After the memory upgrade in Satellite A100-1401E the system freezes

Similar Questions

• Memeroy upgrade in Satellite A100 - 529 does not work

  I am trying to upgrade memory on my Satellite A100-529 (PSAA2E). The system comes standard with DDR2 PC2-4200 1x512mo. I installed 2x512MB DDR2 PC2 5300 and the system tries to turn 5 x without success.

  All the documentation said that RAM DDR is backward compatible. The A100-529 will take only PC2 - 4200?

  I found this page useful:
  [Memory for Toshiba Satellite A100-529 | http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=23657&ft=m&st=3]

  According to the details of the memory, it must use the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM memory modules!

  Using other modules you notebook primer not correctly or will not run stable!

  Concerning

• There is no part (PSAAKL) number satellite A100 - 1401E

  I use the Satellite A100 - 1401E with part number PSAAKL - 00 002 M running Vista Home Basic. I installed windows XPsp2, I can't find the proper drivers, because PSAAKL - 00M 002 part number is not available in the list of model/partnumer. Is there some equivalent models/series that I can use? Could you help me?

  Thanks in advance

  Maurice is right. Many people are confused about that. Just check support page Toshiba of the country where you bought your laptop.

• Satellite A210-1UP - every few minutes the system freezes

  Hello

  I just installed windows 7 32 bit on a satellite A210-1UP

  Every few minutes the system freezes and then continues as if nothing had happened.
  No error or blue screens are displayed

  I would like to know if windows 7 can work without problems on this system?
  That is the version of the bios recommended to run windows 7?

  Thanks in advance!

  Kind regards
  Stijn

  Hello

  Yes, you can run Windows 7 on the A210.
  I ve got an A210 and installed Win 7 32 bit.
  It runs correctly without big problems.
  I have collected the drivers Windows 7 and install it on the system.

  Some missing Toshiba Software, that I could find in other series of satellites; for example, L500.
  Here I chose ve the VAP and Support utility Flash memory card in order to get the FN and the multimedia to work keys.

  PS: I no has not updated the BIOS as it was not necessary; everything is ok.

• After the system restore, clock is located one hour before because of DST

  Because of a logon error, I had to perform a system restore.  After the system restore has completed, I noticed that my clock is set ahead one hour (DST).  I think that TimeZones eventually applied twice to the clock.  I can put back an hour, but I rather it would be correct.  I tried to re - download the patch for the DST, but that did not help.

  Have you tried to reset the clock -

  "With the time server Sychronising Internet?

  Have you checked your area etc

  TaurArian [MVP] 2005-2010 - Update Services

• After the system is booted, the logon process takes 20-30 minutes.

  Microsoft Windows Vista Business SP2 [Version 6.0.6002] / ThinkPad x 301 2776 - A23
  The problem was discovered in November-December 2013.
  After the system is booted, the logon process takes 20-30 minutes (the mouse cursor on the black screen).
  I faced the same behavior in "windows boot" mode when Kaspersky Anti-virus is also uninstalled.
  After 30 minutes, as soon as it was possible to run msconfig, I checked and made sure only microsoft services are running.

  Dear Carlos, thank you very much for the help! The problem was solved by executing the steps suggested in this discussion. Please close this message.

• After the system recovery running following a power outage, my user profile is lost. Unfortunately, he is also the administrator account. How to retrieve the profile or create a new?

  After the system recovery running following a power outage, my user profile is lost.  Unfortunately, he is also the administrator account.  How to retrieve the profile or create a new?

  ·                        Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  ·                        http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  See if the information in the above tutorial will help you.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Difficulty of a corrupted user profile

  After creating the profile, you can copy the files from the existing profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/947242

  A temporary profile is loaded after you connect to a Windows Vista-based system

  See you soon.

  Mick Murphy - Microsoft partner

• No output on the monitor after the system resumes

  After the system goes into hibernation mode, then the mouse is moved or no key is pressed, the monitor does not come to the top again. On the keyboard it no NumLock light at the moment, although num lock is also pressed. If at this time monitor is turned on, it displays "VGA input No Signal" and monitor goes to sleep. Only way is to force a reboot of the system

  Hi AnjanaKumar,

  There are a few things to possibly resolve this problem.

  1. you'll want to make sure you update your video drivers directly from the video card manufacturer's Web site.

  2. it could be the power plan that you configured is not compatible with your configuration:

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-create-or-delete-a-power-plan-scheme

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Windows calendar after the system restore notes no longer exist.

  The Windows calendar after the system restore notes disappeared forever, or can be found somewhere?

  Hello
  
  First we recommend that you search the .ics files confirm the windows calendar old files are present on the hard drive.
  Visit this link for more information: http://windows.microsoft.com/en-US/windows-vista/Tips-for-finding-files
  Windows Vista has an option to cancel the system restore. To do this, follow these steps.
  1. open the system restore by clicking the Start button, all programs, accessories, clicking System Tools, and then click System Restore.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  2. click on undo system restore and then click Next.
  3. proceed to review your choices and then click Finish.
   
  Your computer will restart. When you are finished, you will see a confirmation that the cancellation is complete.
  
  For more information, see this link: http://windows.microsoft.com/en-US/windows-vista/Undo-System-Restore
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problems with the updates after the system recovery

  Hello.

  After about a week after the system recovery, my computer tried to install updates 110 and stuck on number 56 for more than 3 hours.

  If I disconnect the battery and restart the system stuck halfway through the Configure updates - again for several hours.

  Someone knows what's the problem?

  Regards Terry

  Hello Terry,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem can occur because corrupt Windows Update files or parameters.

  I suggest you run the Windows update troubleshooting tool and check if that helps. Please follow these steps:

  a. press Windows + C keys and click on research.

  b. type Troubleshooting in the search box, click on it in the search results.
  c. click 'show all' and then click 'Windows Update'.
  d. click on 'Next' and follow the on-screen instructions.

  If this does not help, please reset the Windows update components and check.
  Refer to this article:
  How to reset the Windows Update components?
  https://support.Microsoft.com/en-us/KB/971058

  Note: Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  https://support.Microsoft.com/en-us/KB/322756

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• After the system starts. I get the error message; "" Unable to start Bluetooth stack service "from BTTray.

  After the system starts. I get the error message; "" Unable to start Bluetooth stack service "from BTTray.

  Pls I need help to resolve this error message.

  Concerning

  Unfortunately, this model laptop has a Broadcom bluetooth device or a device of Atheros.

  Try to install the Atheros driver first because it is more common.  If it isn't an Atheros card, Setup HP rejects the update indicating no match of material.

  If this isn't Atheros, install the Broadcom bluetooth driver.

  Here is the page of the driver for your laptop and Windows 7 64-bit.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5218666#n311

  Bluetooth drivers are in the category network drivers.

  Let me know what happens.

• Portege M800-106 the system freezes when I connect a device via USB

  When I connect a device through a USB port, the system hangs. This happened with any device even something that has been used before. Example - if I turn on the printer /plug in my Blackberry to synchronize the .laptop just going so slow that I have to do a reboot with the devices still connected to get the system working again. Running Vista. Any help please?

  Hello

  You see yellow exclamation marks in Device Manager? Maybe a driver isn't installed properly in the system freezes.
  In addition, I would try to remove the USB ports in Device Manager. After this restart your laptop and USB ports will be recognized again.

  Have you tried a BIOS update? If this isn't the case, you should do it. Before you begin the update, close all running programs and make sure that you are logged on as administrator.

  Last but not least try to reinstall Windows using the Toshiba recovery disc. It only takes a few minutes and then you have settings to factory again! :)

• Re: After upgrade on Satellite A100 BIOS cannot use keyboard more

  Need help... after bios upgrade for Toshiba Satellite A100 my keyboard error... now I can't use my keyboard...
  If I used the external keyboard, as there not enough power into the USB...
  Now, how come back to start bios version...

  Thank you or any medium

  Hello

  Enter the BIOS (by pressing F2 at startup) and try to check in the Bios if compatible keyboard, legacy usb support (something like that) is enabled. It should help.
  Otherwise, playing with the up/downgrade Bios (especially, demote) instead of keyboard problem, can cause the crash of the complete system with white screen.

• Question about memory & CPU in Satellite A100-551 upgrade

  Greetings
  I had the misfortune to get 2 SODIMM KVR667D2S5 / 1 G for my laptop Toshiba Satellite A100-551 that don't work by themselves a single sodimm or as a pair, it doesn't matter which slot they go-they do not work.

  However when the 512 MB sodimm Moose is placed in one of the slots - anyone - either of the kvr etc. SODIMM work giving a total of 1.5 GB of ram.
  Please help me solve this problem.

  Also is it poss to upgrade cpu IE is nested cpu. I already upgraded a laptop cpu when thay had nested CPU, so I am aware of the problems that arise
  Thank you all for your help in this matter.

  Concerning

  Hi Mike

  > I had the misfortune to get 2 SODIMM KVR667D2S5 / 1 G for my laptop Toshiba Satellite A100-551 that don't work by themselves a single sodimm or as a pair, it doesn't matter which slot they go-they do not work.
  It of clear-> modules seems to be not not compatible ;)

  > However when the original 512 MB sodimm is placed in one of the slots - anyone - either of the kvr etc. SODIMM work giving a total of 1.5 GB of ram.

  Can't believe that! As far as I know this laptop was shipped only with a 512MB DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM module.
  Of course you can improve the memory up to 2 GB using two modules 1024Mo.

  Compatible memory that you can find here:
  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=20890&ft=m&St=3

  > Also is it poss to upgrade cpu IE is nested cpu. I already upgraded a laptop cpu when they had nested CPU, so I am aware of the problems that arise
  Well, what say, the CPU is hit you can find easily by using a material like Everest diagnostic program. It would provide useful information on your laptop hardware.

  But to be honest, I'm very skeptical as to upgrade CPU on laptops.
  If you have already modified several processors on laptops so you know that's not very simple and more complicated as the CPU upgrade on desktop computers.

• Upgrade memory on a Satellite A100-912

  I am the owner of a Satellite a100-912 and I want to improve his memory!
  As it seems, this model supports only the modules SODIMM DDR2 PC2-4200 (533 Mhz). Before the purchase of a memory module that might regret, I want to know if there will be compatibility problems if I use this module of PC2-6400 DDR2 SODIMM for notebook (800 Mhz).

  Will it work, even at low clock speed (533 Mhz), or it's going to be a total waste of money?

  As far as I know that the FSB is capable of managing modules to 667 Mhz.
  You can use the lower modules (533 Mhz) without any problem but modules with superior Mhz will not work at full speed because of the limit BSF.

  So I t recommend buying 800 Mhz modules. First of all, they are not supported and secondly it s waste of money!