After upgrading to 11.2.0.1 performance issues

Similar Questions

• Performance issues after upgrade to view 5 on Windows 7

  I'm having a lot of performance problems after upgraded to vSphere 5 and 5 view connecting using PCoIP.  Interaction with the virtual machine are slower with either double or single monitor.  I tried all solutions different workaround proposed on the site of Teradici.  If someone has bugs or suggestions about how do to clear up things please answer.

  Add the following line in the vm config file.

  mks.poll.headlessRates = 1000 100 2

  It should solve your PCoIP lag problems, let me know what your results are.

• Trackpad MacBook Pro late 2011 does not not after upgrade

  I just update the OS in my MacBook Pro (late 2011) which worked perfectly well 'El Capitan' to 'Sierra '. Everything went, smooth and pleasant. but now, the trackpad is completely erratic, is in itself (such as move and open programs like possessed). I tried several suggestions from apple such as checking for updates, check the settings, delete all the gestures, etc. I'm assuming that the material is very well that was perfectly fine yesterday... any suggestions please help.   -Note; I have to use an external mouse, and the latter is very well.

  Hello Med_,

  Thank you for using communities of Apple Support. It is my understanding that after upgrading to Sierra, your MacBook trackpad has become erratic. I know that my trackpad is an important part of my daily use, I can certainly understand your concern. I'm here to help get this resolved with you.

  You did an excellent job so far! Then I recommend the system management controller (SMC) reset. This system can solve some unexpected behaviors. Follow the steps below:

  1. Stop the Mac.
  2. Unplug the MagSafe from Mac power adapter.
  3. Remove the battery. (Learn about removing the battery in the MacBook and MacBook Pro computers).
  4. Press and hold the power button for 5 seconds.
  5. Reconnect the battery and the MagSafe power adapter.
  6. Press the power button to turn on the Mac.

  The LED on the MagSafe power adapters could change State or temporarily disable when you reset the SMC.

  Reset the management system (SCM) controller on your Mac.

  If the problem persists, test this problem in safe mode. This will allow you to exclude the software as the cause. To help get started in safe mode and additional steps, use the steps and the link below:

  1. Start or restart your Mac.
  2. As soon as you hear the startup tone, hold down the SHIFT key.
  3. Release the SHIFT key when you see the logo Apple appears on the screen.

  After the Apple logo appears, this may take longer than usual to reach the login screen or your office. This is because your Mac performs a check of directory of your drive to boot in safe mode.

  To leave safe mode, restart your computer without pressing any keys during startup.

  Try safe mode if your Mac does not end commissioning

  See you soon!

• Satellite A300: TRDC reminder & Toshiba Recovery Disc Creator works after upgrade to Windows 7?

  Hello

  I'm sorry for the bad English.
  Satellite A300.
  Has performed the update to Win7 upgrade Toshiba program.

  This program works;
  TRDC reminder and Toshiba Recovery Disc Creator after update to Wins7?

  The TRDCReminder program found no "revival of the computer.
  Toshiba Recovery Disc Creator program was created and incomprehensible?

  If what these program how to recover your computer in case of failure?
  TEMPRO works in Win7?

  Thank you very much.
  With greetings.

  Igor.

  Hello Igor

  In my opinion, you must create recovery disk before upgrade you to Win7. I did the same thing.
  Later, if something goes wrong, you can use your disks and install Vista using the created recovery disks.

  I don't understand why you want to wait and create these disks after upgrade. This recovery creator disc doesn t create recovery image in the current state, but always the same recovery image, you got with your laptop.

  TEMPRO should work in Win7 too.

• Pavilion dv6-4024tx: display random crashing after upgrade to Windows 10 (back to Windows 7)

  Hey all,.

  I used to own a computer laptop dv6-4024tx Pavilion which I gave to my father to use after you have bought a new laptop for my part. It was in pretty good condition when I gave it to him, with the only problem being that she would get very hot unless a cooling pad was used (which I it comes with). At the time, it was running Windows 7 Home Premium with no problems and everything was fine. However, it might be interesting to note that while I had it I had problems with random blue screens while I was with the latest graphics drivers, so I drove back to the drivers supplied on the support page for this laptop. After I "upgraded" to Windows 10 (do not perform a clean install) for my dad, the laptop would randomly crash and display something like the photo that I have attached, before going empty and show again several times. Believing that it would be a problem with the GPU, I went and Display Driver Uninstaller to remove completely all AMD drivers and software, downloaded the latest driver on the AMD website and installed. It seemed to temporarily solve the problem, but as it's always within 30 days of installation, I offered to go back to Windows 7, but my father wanted to leave it and see how it happened. Oddly enough, for the next month, it never reported the laptop crashing again and the time period for return finally expired. The problem of course back then I tried the same solution from before but the noise continued. I tried to disable the GPU completely from the Device Manager, so that the laptop was running with Microsoft Basic display adapter. He seems to have stopped the fracas, but less than a week my father told me that he had crashed again.  I tried to restore the laptop to a system image I had done years ago, but I learned that you cannot restore an image to a different version of Windows System. Finally, as a last resort I backed everything up and made a real clean install of Windows 10, and the problem has not yet disappear.

  My goal now is to return the Windows 7 laptop somehow. I can mount a virtual image of the system hard drive and access all the recovery files provided by HP, specifically the Recovery Manager. From there, I can do a recovery USB or DVD (s) we hope to restore the laptop to all conditions of factory (so theoretically return to Windows 7). I will try this, but I need a flash player more than 20 GB or several blank DVDs I don't currently. In addition, Recovery Manager says that this medium can never be created once, so it save me time and money (not to mention my last lifeline) if someone could please share their views on the question of whether this method would be successful or not. I know in case it doesn't work, there is always the question of registration of the OS by Microsoft, but I can cross that bridge when I get to it.

  Sorry for the essay I just wrote, but this has been a problem for too long, and I am at a loss to know what to do now (apart from the purchase of another computer). If there are any questions I'll be happy to answer, and I hope we can get this issue is resolved. See you soon.

  

  If you follow this step 3.

  http://www.SevenForums.com/tutorials/675-system-image-recovery.html

  You will need to select "format and repartition disks" as windows 10 will have changed partitions.

• All-in-one Officejet 5610: function Scan lost after upgrade to Yosemite

  Lost the ability to analyze after upgrade, print, and copy works. Have already done everything suggested by Double-U-di in the Mac OS 10.10 post Yosemite and HP Printer Support posted on 30/10/2014: checking for updates Apple, printer removed from the queue, add printer back, reset the printing system, removed the HP software, repair disk permissions * manually installed HP printer drivers v3.0 and added to the queue printer. No change, printing & copying ok, but the scanner does not.

  During approval of the repair disk found a number of problems related to printing and presumably repaired, had more to do with the ' should be 80, group is zero ", but others as well.

  Anyone know what I can do, short of buying a new printer? I realize, it's a dinosaur - always attached via the USB port, but she worked just beautifully before the upgrade.

  Hello @DrBucky,

  Welcome to the Forums of HP Support!

  I understand that you are not able to scan from your HP Officejet 5610 all-in-One Printer to your computer Mac OS X 10.10. I would like to help you to solve this problem today. Thank you for all the troubleshooting steps you tried before reaching out for support. You have completed almost all of the recommended steps. However, the order in which the steps have been completed can cause some problems. Therefore, I will be having repeat you some of these measures to ensure that the appropriate driver is being used.

  Step 1: Reset the printing system and uninstalling the driver:

  It is crucial for the repairs we have a clean slate to work with. Therefore, I'll take you reset the printing system and Uninstall the drivers for your HP Officejet. Please click here for instructions on how to perform the reset and uninstall. Once the site opens, select the drop-down list for 'Mac OS X v10.6, OS X v10.7, OS X v10.8 and OS X v10.9'. Then, please follow the steps in the method 1 and method 2.

  Once steps have been taken, please proceed to the next step.

  Step 2: Check and repair your Mac disk permissions:

  It is very important to perform the audit before the repair. By running the check first, questions are found. Once all questions are found the repair process will correct these problems. By repairing just without checking first, questions may be missed.

  1. Open Macintosh HD and go to Applications
  2. Go to the Utilities folder
  3. Open disk utility
  4. Select the hard disk volume, you use (usually on the left)
  5. Select verify disk permissions
  6. Once this process is complete, select repair disk permissions

  Step 3: Manually install the driver Package:

  Please click here to manually download the package from Apple to HP v3.0 printer driversupdate. Once the site opens click on the download button at the top. Follow the instructions on the screen to install the driver package.

  Step 4: Check the Apple updates:

  1. Go to the Apple
  2. Select System Preferences
  3. Select software update
  4. Click update now
  5. Install your available updates
  6. Computer restart

  Step 5: Add the device:
  

  1. click on the menu of Apple , then Preferences System.

  2. click on Print & Scan and then check if the name of your printer appears in the printer list.

  3. click on the name of your printer, click the sign minus (), then remove the printer.

  4. click on the plus sign (), click Add a printer or a Scanner, click the name of your printer.

  5. click on the area of use or with the help of Print and then select the name of your printer on the shortcut menu. Ensure that the Officejet driver is selected.

  

  6. click Add to add the printer to the list.

  -Source

  Once your printer is properly added to, please try to scan the image. For instructions on the three supported methods of scanning without HP software please click here. The support document indicates that it is for Mac OS X 10.8 but the steps are the same for Mac OS X 10.10.

  Please let me know if a retry of the procedure described in this new order solves your problem of scan. Good luck!

• After upgrading to SP3 of XP SP2, the games is works more slowly or doesn't do at all

  After upgrading to XP SP2 Sp3, games run more slowly or not at all

  Hi Chris,

  To help you better, please answer these questions.

  1 are. What games you referring?

  2. it's getting to a particular game?

  3. are you play game online or installed on the computer?

  4 did you do changes on the computer before the show?

  You can visit the article to optimize the computer's performance.

  Slow PC? Optimize your computer for peak performance

  http://www.Microsoft.com/athome/Setup/optimize.aspx#fBid=w9DbbruDxuH

  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  If you need help with the Windows operating system, just tell me and we will be happy to help you.

• BEFSR81 v3 after upgrade without browser admin access

  After upgrading my BEFSR81 v3 to the latest firmware (2.51.4, build 001 June 13, 2008) I often have problems of access to the Web interface.

  Immediately after a reboot, I can access and manage the router with Firefox or IE without problem.  But then if I do a configuration change the next day all I get is a blank screen after the login prompt.  The only way to solve the problem is to reboot the router.

  He always asks an id of username/password correctly, and if I get the wrong information I'm getting an authorization failed.  But put the correct password just give the empty window.

  I'm tired of running down in the basement of restart the router every time I need to make a change.  Any idea what's going on?

  My router works better, so I'll give my solution here for others.

  During a chat session on 10 April with the support of Linksys, I explained my problem and was told that I can download an older firmware to the following address, then use TFTP to perform the downgrade.  I checked this address still today while writing this message, and I can't get there more:

  Linksys FTP server

  On 10 April, which worked and I managed to download the 2.50.2 firmware which is old enough, but it's the only version I could find on the site recommended.

  The good news is that worked and my router is functional without obvious problems for about two weeks.

  Today I decided to try upgrading the firmware again.  I am disappointed that Linksys has not addressed this problem somehow because others apparently have similar problems with the "current" firmware version  In fact, there is a certain
  confusion on the Linksys BEFSR81 v3.0 support page.

  As of today (April 26, 2009), the download of the firmware for the BEFSR81 page lists the following:

  2008-06-13
  Ver.2.51.1

  (I'm not that these date and numbers because they do match).

  The file of the firmware provided in the link is actually: 2.51.4.4_20081230_code.bin

  Notes the following version history list:

  Firmware Date: June 13,2008
  Current firmware: Version 2.51.1
  Product PartNo: BEFSR81 v3.x

  2.51.4.4 December 30, 2008
  2.51.4.1 Jun 13,2008
  2.51.3 March 2, 2007
  2.51.1 May 5, 2006
  2.50.4 Nov 15, 2004
  2.50.2 May 19, 2004
  Oct 15, 2003 first version 2.45.5

  So, from my own experience and that of others in these forums, version 2.51.4.4 does not work on the BEFSR81 v3.0.

  There are still 2.51.4.1 on the old Linksys support site:

  Linksys support (old)

  It's the version I have installed now, and so far it seems to work.

  I really wish I could find the version 2.51.3 somewhere that it was the most reliable for me.  Unfortunately, I can't find that anywhere.

  Additional information, another user is in these positions:

  More on version BEFSR81 issues.

• After upgrading my Windows Vista computer to SP2 double my user account icons.

  Original title: After upgrading my Windows Vista computer to SP2 double my user account icons. I'm not trying to delete one of them, because all of the account will be deleted.  How can I fix it?

  I use a laptop Lenovo Dual 32-bit CPU. My OS is Windows Vista Business.

  Hello
   
  Where it seems double?
   
   
  Method 1:
  Step 1:
  
  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode 
   
  If step 1 work, try step 2
   
  Step 2:
  Try to perform the clean boot and check if it helps, here is the link:
  http://support.Microsoft.com/kb/929135
   
  Note: When you're done to diagnose, follow step 7 in the article to start on normal startup.
  
  Method 2:
   
  If the problem persists, you can uninstall service pack 2, put the computer in start state in minimum mode, and then reinstall Service Pack 2 and see if that helps.
   
  Step 1:
  
  Perform the system restore and go back to a date when Service pack was not installed on the computer.
  System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions
   
  Step 2: Put the computer in a clean boot state.
  Here is the link:
  http://support.Microsoft.com/kb/929135
  Note: When you're done to diagnose, follow step 7 in the article to start on normal startup.
  
  Step 3: Download Windows Vista Service Pack 2 here:
  http://www.Microsoft.com/download/en/details.aspx?ID=16468

• Connection problems wireless Broadcom 1704 after upgrade to windows 10

  Connectivity problems after upgrade to windows 10 intermittent wireless;  Have an Inspiron 5748 with adapter Broadcom 1704.  Driver is up to date: 7.35.295.0.  Diagnostic shows no problem with the unit.  Will be generally connect to the network, but the connection is deleted intermittently.  Troubleshooting to solve using leads to restore connectivity, but it will then drop again intermittently.  Never experienced problems before windows upgrade 10.

  steveshuff,

  Here are a few parameters to change on your adapter wireless for better performance.

  Turn on and off then on all devices on the network

  1. Turn off the power to the broadband modem and let the modem broadband disconnected for at least 3 minutes.
  2. Shut down all computers that are connected to the network.
  3. Remove power from the wireless router.
  4. Check that a network cable is connected the modem to broadband in the Internet or the wireless router's WAN port.
  5. Check that no series cables or USB are connected to the Modem on broadband.
  6. Connect the power supply to the modem broadband. Wait at least 2 minutes for the Broadband Modem to initialize.
     (If the Modem does not provide Internet connection successfully, unplug the Modem. Wait at least 5 minutes, then plug the Modem back.)
  7. Connect the power supply to the wireless router. Wait at least 2 minutes for the wireless router to initialize.
  8. Turn on the computer and try to connect to the Internet.

  Difficulty of wireless network connections

  Turn off airplane Mode

  For Dell Wireless adapters:

  1. In the Search box, type Device Manager.
  2. Press or click (Control Panel) Device Manager.
  3. In the Device Manager window, click on the sign of the arrow next to network adapters.
  4. Double click or double-click the Référence Dell Wireless WLAN Card.
  5. Click the Advanced tab.
     Note: These options are not available according to the installed wireless adapter.
  6. In the property: box highlight AP Compatibility Mode, select broader compatibility under value: from the menu drop-down.
  7. In the property: box, highlight the Minimum energy consumption, select disabled under value: from the menu drop down.
  8. Click OK.

  For me, to help troubleshoot, please click on my DELL-Jesse L and send me a private Message with the number of Service Dell and your Dell order number.

• IOM-Exchange Provisioning does not work after upgradation to 11.1.1.6.0

  Hi Experts,

  Need your help to solve the issue of implementation of the exchange connector.

  We upgraded the connector to the latest version 11.1.1.6.0 of 11.1.1.5.0 and applied the patch 18310438 for troubleshooting performance issues.

  After installation, exchange Setup does not work, the statistics remain in readiness, asking for your help to solve this problem.

  

  The newspaper of the server connector that we get the error
  
  DateTime = 2014-03-27 T 05: 09:43.0467023Z
  ConnectorServer.exe error: 0: System.TypeLoadException: could not load type 'System.Management.Automation.Runspaces.InitialSessionState' from assembly 'System.Management.Automation, Version = 1.0.0.0, Culture = neutral, PublicKeyToken = 31bf3856ad364e35'.
  to Org.IdentityConnectors.Exchange.LocalRunspaceInstance.InitRunSpace (component snap snap)
  to Org.IdentityConnectors.Exchange.LocalRunspaceInstance... ctor (component snap snap, ConnectorMessages messageCatalog)
  at Org.IdentityConnectors.Exchange.RunspaceInstanceFactory.Create (ExchangeConfiguration config)
  at Org.IdentityConnectors.Exchange.Service.AbstractPowerShellService.CreateRunspace)
  to Org.IdentityConnectors.Exchange.Service.AbstractPowerShellService.Init (Configuration configuration)
  to Org.IdentityConnectors.Exchange.LocalRunspacePowershellImpl.Init (Configuration configuration)
  to Org.IdentityConnectors.Exchange.ExchangeConnector.Init (Configuration configuration)
  to Org.IdentityConnectors.Framework.Impl.Api.Local.ConnectorPoolManager.ConnectorPoolHandler.NewObject () in c:\ADE\aime_icf\icf\framework\dotnet\FrameworkInternal\ApiLocal.cs:line 108
  to Org.IdentityConnectors.Framework.Impl.Api.Local.ObjectPool'1.BorrowObjectNoTest () in c:\ADE\aime_icf\icf\framework\dotnet\FrameworkInternal\ApiLocal.cs:line 1041
  to Org.IdentityConnectors.Framework.Impl.Api.Local.ObjectPool'1.BorrowObject () in c:\ADE\aime_icf\icf\framework\dotnet\FrameworkInternal\ApiLocal.cs:line 981
  at Org.IdentityConnectors.Framework.Impl.Api.Local.Operations.ConnectorAPIOperationRunnerProxy.Invoke (object proxy, method MethodInfo, Object [] args) in c:\ADE\aime_icf\icf\framework\dotnet\FrameworkInternal\ApiLocalOperations.cs:line 178
  to ___proxy1. Schema()
  to Org.IdentityConnectors.Framework.Impl.Server.ConnectionProcessor.ProcessOperationRequest (request OperationRequest) in c:\ADE\aime_icf\icf\framework\dotnet\FrameworkInternal\Server.cs:line 609

  
  

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------------

  
  

  Details of the environment:

  
  

  1) IOM 11 GR 2 with BP 14 installed.

  2) Exchange 11.1.1.6.0 connector with patch 18310438

  
  Kind regards

  David
  

  Hello

  Error solved with the installation of the hotfix windows http://support.microsoft.com/kb/968930 on the connector server.

  Kind regards

  David

• After upgrading vCenter 5.0 to 5.1 found stored procedure 'purge_stat1_proc '.

  Hi all.

  After upgrading vCenter 5.0 to 5.1 found this error in MS SQL 2008 R2 during the performance of work ""past day stats rollup ": "

  Message
  Executed as user: xx\yyyy. Stored procedure 'purge_stat1_proc' not found. [SQLSTATE 42000] (Error 2812).  The step failed.
  Thanks to VMware KB http://kb.vmware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & docTypeID = DT_KB_1_1 & externalId = 2033096
  and http://kb.vmware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & docTypeID = DT_KB_1_1 & externalId = 2006097 there is no stored procedure in vCenter 5.1 purge_stat1_proc installation but job day cumulative stats exist...
  Also there is not a SQL script for this procedure in the vCenter Server installation folder in C:\Program Files\VMware\Infrastructure\VirtualCenter Server\sql.
  Anyone have a suggestion? Maybe it's a bug?

  The answer lies in the same article that you are looking to:

  http://KB.VMware.com/selfservice/documentLinkInt.do?micrositeID=&popup=true&LanguageID=&externalID=2033096

  The script of vCenter 5.1 to create this task (job_schedule1_mssql.sql) is supposed to create a job with a single step.  It seems that they have decided to remove the purge step and the rest of the procedure for her, but for some reason, that the work is not always updated and the stage of the procedure call (now missing).

  You can fix it by running the script job_schedule1_mssql.sql by the instructions in the article.

• Impossible to deploy the model after upgrading to vCenter v4_1

  Hi all

  I updated vCenter Server from version 4.0 to v4.1 and re-registers the hosts.
  Virtual machines are working well and are able to collect data on performance.

  However, when I tried to deploy the model, error occurred and failed to deploy the model.

  (This model were made to vCenter v4.0 environment, before moving on to vCenter v4.1).

  My client needs deploy the model so that it can create a new server next week...

  I looked to the top of the Knowledge Base and found the following information.

  ----------------------------------------------------

  Knockout No. 1036224
  VMware KB after upgrading to vCenter Server 4_0 to 4_1, deployment of a model with a comments customization fails

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1036224 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 321118019 & StateID = 1 0 321114529

  ----------------------------------------------------

  If there is anyone who has solved this problem by following the procedures written in this KB, could you tell me at what level you updated VMware tools for?
  In addition, was the update of the virtual hardware to solve this problem?
  (I hope that the material of the VM is v7, which is the last for ESXv.4.0, update the virtual hardware is not required in my environment :)

  Thanks for you information in advance!

  
  < environment >
  Before the upgrade: vCenter Server * v4.0*, ESX v4.0.0, v7 (latest) of Virtual Machine hardware,.
  After upgrade: vCenter Server * v4.1*, ESX v4.0.0, v7 (latest) of Virtual Machine hardware
  (I've specifically updated only the vCenter server and ESX and VM(Windows/Linux) are not updated).

  Hello

  Try to convert the template to a virtual machine, then new - VM model.

  Sounds strange, but it works for us

• .PS generate a blank PDF file after upgrading from Acrobat Pro 7 to 9 of the file

  Hi all

  I searched for it in vain, so I come to you now in desperation. My boss asked me track down this error and I have to be honest, I'm a little green with Acrobat Pro. So come the situation I know. My Department, usually use a .ps file to generate a publication as a PDF of the other .ps files. We operate on a network share (drive P :) on Windows XP SP3 machines with the latest updates.

  In Acrobat Pro 7 we can double-click the .ps file that executed the code through Adobe Distiller and a finished PFD at the same file below name would exit in the host directory. But now, after upgrading to Adobe Acrobat 9, this process produces a PDF file with all bookmarks appropriate and no content.

  %!
  % Program postScript for distilling and combine multiple PostScript files.
  % During the incorporation of subsets of fonts, it is strongly recommended that you use this technique
  % to distill several subset of police for one of the PS file is used for each policy.

  /prun {/mysave save def % performs a backup before running the PS file}
  DUP = RAS % watch running PS file name
  RunFile built in distilling procedure calls %
  Claire cleardictstack % cleans up after PS file
  mysave restore % restorations save level
  } def
  [/Author (user)
  / CreationDate)
  / Creator)
  / Title (title)
  / Topic (Subject)
  / Keywords (words)
  / DOCINFO Pdfmark
  [/PageMode
  / UseOutlines
  / DOCVIEW pdfmark
  [/ Page 1]
  / View [/ XYZ null null null]
  / Title (cover Page)
  / OUT pdfmark
  [/ Page 2]
  / View [/ XYZ null null null]
  / Title (Page 1)
  / OUT pdfmark
  [/ Page 3]
  / View [/ XYZ null null null]
  / Title (Page 2)
  / OUT pdfmark
  [/ Page 4]
  / View [/ XYZ null null null]
  / Title (Page 3)
  / OUT pdfmark
  [/ Page 5]
  / View [/ XYZ null null null]
  / Title (Page 4)
  / OUT pdfmark
  [/ Page 6]
  / View [/ XYZ null null null]
  / Title (Page 5)
  / OUT pdfmark
  [/ Page 7]
  / View [/ XYZ null null null]
  / Title (Page 6)
  / OUT pdfmark
  [/ Page 8]
  / View [/ XYZ null null null]
  / Title (Page 7)
  / OUT pdfmark
  [/ Page 9]
  / View [/ XYZ null null null]
  / Title (Page 8)
  / OUT pdfmark
  [/ Page 10]
  / View [/ XYZ null null null]
  / Title (Page 9)
  / OUT pdfmark
  [/ Page 11]
  / View [/ XYZ null null null]
  / Title (Page 10)
  / OUT pdfmark
  [/ Page 12]
  / View [/ XYZ null null null]
  / Title (Page 11)
  / OUT pdfmark
  [/ Page 13]
  / View [/ XYZ null null null]
  / Title (Page 12)
  / OUT pdfmark
  [/ Page 14]
  / View [/ XYZ null null null]
  / Title (Page 13)
  / OUT pdfmark
  [/ Page 15]
  / View [/ XYZ null null null]
  / Title (Page 14)
  / OUT pdfmark
  [/ Page 16]
  / View [/ XYZ null null null]
  / Title (Page 15)
  / OUT pdfmark
  [/ Page 17]
  / View [/ XYZ null null null]
  / Title (Page 16)
  / OUT pdfmark
  [/ Page 18]
  / View [/ XYZ null null null]
  / Title (Page 17)
  / OUT pdfmark
  [/ Page 19]
  / View [/ XYZ null null null]
  / Title (Page 18)
  / OUT pdfmark
  [20/page
  / View [/ XYZ null null null]
  / Title (Page 19)
  / OUT pdfmark
  [/ Page 21]
  / View [/ XYZ null null null]
  / Title (Page 20)
  / OUT pdfmark
  [/ Page 22]
  / View [/ XYZ null null null]
  / Title (Page 21)
  / OUT pdfmark
  [/ Page 23]
  / View [/ XYZ null null null]
  / Title (Page 22)
  / OUT pdfmark

  prun (p:/ps/pdf/cover.ps)
  prun (p:/ps/page2.ps)
  prun (p:/ps/page3.ps)
  prun (p:/ps/page4.ps)
  prun (p:/ps/page5.ps)
  prun (p:/ps/page6.ps)
  prun (p:/ps/page7.ps)
  prun (p:/ps/page8.ps)
  prun (p:/ps/page9.ps)
  prun (p:/ps/page10.ps)
  prun (p:/ps/page11.ps)
  prun (p:/ps/page12.ps)
  prun (p:/ps/page13.ps)
  prun (p:/ps/page14.ps)
  prun (p:/ps/page15.ps)
  prun (p:/ps/page16.ps)
  prun (p:/ps/page17.ps)
  prun (p:/ps/page18.ps)
  prun (p:/ps/page19.ps)
  prun (p:/ps/page20.ps)
  prun (p:/ps/page21.ps)
  prun (p:/ps/page22.ps)
  prun (p:/ps/page23.ps)

  
  % INSTRUCTIONS
  %
  % 1. Find all PostScript files in distiller.
  %
  % 2. Make a copy of this file and give it the name you want to have as a prefix
  % for the rΘsultat file. For example, you can name this file MyBook.ps.
  %
  % 3. Include a line for each PostScript file to run by using the syntax of path
  % appropriate for the Acrobat Distiller platform running.
  %
  % Macintosh path syntax: prun (Macintosh HD:Folder:File.ps)
  % Windows path syntax: prun (c:/mydir/file.ps)
  % UNIX pathname syntax: (. / mydir/File.ps) prun
  %
  % Note: the syntax for Windows may seem strange, but the double escapement of the
  % backslash is required to use filenameforall.
  %
  % 4. Distill the file on the computer running Acrobat Distiller.

  Once the process is 'done' the following log file is generated.

  Acrobat Distiller 9.4
  Start: Monday, October 18, 2010 at 13:32:05

  Adobe PostScript software version: 3018.101

  Start time: Monday, October 18, 2010 at 13:32:06
  Source: publicationtest.ps
  Destination: C:\Documents and Settings\User\Desktop\usfdtest.pdf
  Adobe PDF settings: C:\Documents and Settings\User\Application Data\Adobe\Adobe PDF\Settings\High quality Print.joboptions
  c:/ps_script/cover.PS
  c:/ps_script/TOC.PS
  c:/ps_script/page3.PS
  c:/ps_script/page4.PS
  c:/ps_script/page5.PS
  c:/ps_script/page6.PS
  c:/ps_script/page7.PS
  c:/ps_script/page8.PS
  c:/ps_script/Page9.PS
  c:/ps_script/Page10.PS
  c:/ps_script/page11.PS
  c:/ps_script/page12.PS
  c:/ps_script/page13.PS
  c:/ps_script/page14.PS
  c:/ps_script/page15.PS
  c:/ps_script/page16.PS
  c:/ps_script/page17.PS
  c:/ps_script/page18.PS
  c:/ps_script/page19.PS
  c:/ps_script/page20.PS
  c:/ps_script/page21.PS
  c:/ps_script/page22.PS
  c:/ps_script/page23.PS
  Distill time: 00 hour (s): 00 minute (s): 00.390 second (s)
  End of job *.

  Is there something obvious that shouts, "you're a fool!"? I agree with that, simply to repair.

  I thank in advance for any help you can provide.

  Michael

  Run the Acrobat Distiller with the /F. command-line option

• Time Machine does not work after upgrade to Sierra

  The Time Machine (TM) fail to start backup and there is still "preparing backup...". "for more than an hour. This right after upgrading to Mac OS Sierra.

  Another weird thing happens to the toolbar of the Mac Mail. The Junk button is replaced by another button. trying to put back in place, but remove the button become a button.

  Please help with the backup problem mentioned above. Thank you much in advance.

  How long have you waited? After a new installation, it must be a fair while even with a SSD to prepare the first backup due to the number of modified files.

  Make sure the TM drive is in the list of items excluded from Spotlight indexing. ICloud newsletter and other cloud services.