AIR-AP1131AG-A-K9 Reload reason: IMPOSSIBLE CRYPTO INIT.
Hi all
I have a standalone model AIR-AP1131AG-A-K9 AP and have changed the TURN mode by using the command archive mannual. However after changing the mode on my KNEES it gives below the journal and keep at the start.
Reload LWAPP customer. Reload reason: IMPOSSIBLE CRYPTO INIT.
> I found it at the bottom of the link that the ground is as mentioned in point number 9, however solution did not work.
http://www.Cisco.com/en/us/products/ps6366/products_tech_note09186a00808f8599.shtml
> I have downloaded CiscoAironet-AP-to-LWAPP-Upgrade-Tool-v34.exe to level, but after running the file, nothing happens.
Kindly help me to understand what is wrong with my AP?
Here are the logs.
* 00:00:06.644 Mar 1: % LINK-3-UPDOWN: Interface FastEthernet0, changed State to
* 00:00:07.644 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed State to
AP >
* 00:00:18.603 Mar 1: % CDP_PD-4-POWER_OK: full power - supply NEGOTIATED online
* 00:00:24.691 Mar 1: % LWAPP-5-CHANGED: LWAPP changed state of DISCOVERY
* 1 Mar 00:00:24.711: LWAPP_CLIENT_ERROR_DEBUG: lwapp_crypto_init_ssc_keys_and_certs no cert in the CSS file private
* 1 Mar 00:00:24.711: LWAPP_CLIENT_ERROR_DEBUG:
* 1 Mar 00:00:24.711: lwapp_crypto_init: PKI_StartSession failed
* 00:00:24.729 Mar 1: % SYS-5-RELOAD: reload LWAPP CUSTOMER the request. Reload reason: IMPOSSIBLE CRYPTO INIT.
* 00:00:24.729 Mar 1: % LWAPP-5-CHANGED: LWAPP changed State to DOWNXmodem the file system is available.
This should work for you
http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/u...
Sent by Cisco Support technique iPhone App
Tags: Cisco Wireless
Similar Questions
-
Cisco WLC 2504 with AIR-AP1131AG-A-K9
Hello
Can you help me for some info about AIR-AP1131AG-A-K9.
I have a wlc 2504, but I don't know if the AIR-AP1131AG-A-K9-supported 2504 wlc.
Can work this WLC 2504 with AIR-AP1131AG-A-K9 solution?
If so, guide.
Thank you very much
Gezimv
Check out this link. As long as you have software version 8.0.x 2504 version you can use 1131 AP with it. Nothing beyond software fate is more a series of support 1131.
http://www.Cisco.com/c/en/us/TD/docs/wireless/compatibility/matrix/compatibility-matrix.html#56735
HTH
Rasika
Pls note all useful responses *.
-
How can I solve shot Firmware update on AIR-AP1131AG upward
Hello
I recently tried to update the IOS on the my 1131AG Wireless bridge using the Web interface. The upgrade hung up after only a few minutes and now I cannot access the AP WEb interface and it green / flashing orange.
At the terminal, I get this
17:23:42.983 Dec 5: % CAPWAP-5-DHCP_RENEW: could not find WLC by using DHCP IP
. Renew DHCP IP.
Not in a bound State.
* 17:23:52.861 Dec 5: % ADDRESS_ASSIGN-6-DHCP: Interface FastEthernet0 assigned D
Address HCP 192.168.200.104, mask 255.255.255.0, hostname AP001a.e26d.8244Translate "CISCO-CAPWAP - CONTROLLER.vsnl .net '... the domain server (192.168.200.254)
Translate "CISCO-LWAPP - CONTROLLER.vsnl .net '... the domain server (192.168.200.254)
* 17:23:59.485 Dec 5: % 3-CAPWAP-ERRORLOG: did not D log server settings
HCP.
* 17:23:59.511 Dec 5: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROL
LER.vsnl.net
* 17:23:59.536 Dec 5: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-LWAPP-CONTROLL
ER.vsnl.net-L' device with IP 192.x.x.254 is my desktop PC where I was upgrading from the AP. The PA and my office is connected to a Linksys RV042 SOHO router that also serves as a DHCP server.
I am moving back to the old version and I don't know how to do it. I'm not an expert with the IOS controls and my knowledge is very basic. This facility is part of the configuration of my home network. Any help to solve this problem in highly appreciated.
Pls. Let me know if you need more information.
Thank you
Vincent
The best way to convert a point of LWAP access to autonomous is to use the method of the Mode button:
By using a TFTP server to revert to a previous version
http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp160918 -
What is the Aironet AP1131AG or stupid to use... Pls help!
I'm new to all this wireless Cisco come more school "Apple Airport" of wireless. I bought two AIR-AP1131AG-N-K9 and thought I could pretty well plug & play, but the months of play and I don't always have their work? I have a few stupid questions and hoped that someone could throw me a line?
All I wanted was to have a wireless node that would relay DHCP pray for my 2K 3 server and allow wireless clients to connect as if they were wired (to make it simple)
I have:
-Catalyst 3560G (12.2 (25) SEE2)
AIR-AP1131AG-N-K9 (12.3 (8) JEA3) x 2
The Catalyst 3560 G AP connection port is configured in trunk mode. The AP has had all the security and encryption opened upward for troubleshooting. I created a SSID and he attributed to my main network VLAN (5). Can find anywhere where I define my DHCP server...
Stupid questions:
1 - is the AIR-AP1131AG-N-K9 actually do what I want or have I not the wrong thing?
2. I use the IOS on the AIR-AP1131AG-N-K9 right?
3. I searched here for advice on setting up the PA... is this the right place?
http://www.Cisco.com/en/us/docs/wireless/access_point/12.3_8_JA/configuration/guide/1238jasc.html
Thank you in advance to anyone who can shed some light on my dilemma.
George (the fool)
George,
As long as you properly trunking, the dhcp users request is sent to the VLAN that you have configured the ssid on. The vlan management must be native on the trunk and configured on the access point, other than that, try to configure a dhcp server on the switch and see if the users get an ip address. If they do, then you have a problem with the device of L3, dropping the broadcast dhcp or you don't have vlan 5 configured on all of your devices of l2.
-
I have a (AIR-LAP1131AG-A-K9), I can set it up as a stand-alone?
I have a lightweight access point (AIR-LAP1131AG-A-K9). I would like to use it as a stand-alone gateway (AIR-AP1131AG-A-K9). Is this possible? There are configuration changes that need to happen to make this happen? Do I need to use different operating system?
Thank you
Siva
Plug the AP directly on your PC not the router.
The best way to proceed is to comfort in the AP and make sure that the
AP can reach the laptop via a switch or a crossover cable
fixing directly from the laptop and the AP.
With your cable from the console, you will be able to see if you pressed on the
button for 20 seconds.
By using a TFTP server to revert to a previous version
Follow these steps to return standalone by LWAPP mode
Download a version of Cisco IOS using a TFTP server:
Step 1 in the IP address of the computer on which your TFTP server
software should be from 10.0.0.2 to 10.0.0.30.
Step 2 make sure that the PC contains the image point (for example file
as c1200-k9w7 - tar.122 - 15.JA.tar for series 1200 point access) in the
The TFTP server folder and the TFTP server is activated. Monitor of the
TFTP program to see the code for transfer to the AP.
Step 3 Rename the access point image file in the TFTP server folder
C1200-k9w7 - tar.default for series 1200 point access,
C1130-k9w7 - tar.default for a series of 1130 access point, and
C1240-k9w7 - tar.default for 1240 series access point.
Step 4 connect the PC AP with a category 5 (CAT5)
Ethernet cable. This must be a crossover cable if connected
to the AP. Or ethernet cable is normal if the AP and laptop are connected
to a switch.
Step 5 disconnect the power to the access point.
Step 6 push the MODE button and hold the button while you reconnect power to the access
point.
Step 7 press and hold the MODE button until the status light turns red
(about 20-30 seconds), then release.
Step 8 wait that access point restarts, as attested by all lights
Green followed the status light blinks green.
Step 9 after the access point reboots, reconfigure using the graphical interface or
the CLI.
If the image is not download from Server/tftp on your computer, you may need to delete the previous image of tar on the access point of the console:
Simply hold the mode button until the light is red.
Then, by using the console port, make sure that the guest is AP: and do a show «»
"Flash:" on the device and make sure that there is no image that begins
"c1130-rcvk9w8-tar..." ». If there is an image that starts with who then
Delete it with "delete flash:
-
Hello Experts,
We are in the process of purchase of 5 1131AG Cisco AIR-LAP1131AG-E-K9. However I have some doubts to clear
a. first of all, we don't have WLC
b.Will AP have IOS? What version it will be.
can c. I convert their AIR-AP1131AG?
d. or keep them as TOUR
Please can someone help pe clrarify these doubts.
Thank you
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}
Hello
Please use the below doc and this will solve the problem we are facing...
https://supportforums.Cisco.com/docs/doc-14960
Let me know if this answers your question!
Concerning
Surendra
-
We will deploy a wireless solution using the Access Point 1130AG (AIR-AP1131AG-A-K9) with Cisco WLSE works (CWWLSE-1030-K9).
The questions are:
Are there recommendations for the location of Cisco WLSE to work in this building? Furthermore, the building has five floors and each floor has access switch that supports PoE with empty ports Giga?
Second, how many access points are recommended on each floor, floor size is 37.5 x 24 m ^ 2. And all floors are identical in the nature of the building (Council Jobson partition) and the number of users?
Thank you
HASSAN
Hassan:
First of all, the WLSE is like any other server platform, so anywhere with a suitable environment (power/UPS cool, decent, connectivity) should be OK.
About the recommendations on APs how much and where to put em... Well, which is much more difficult.
The only sure answer is that depends on the outcome of an investigation on the right site.
There are so many variables to any given environment, and they are almost always different, that a response may be the result of pure speculation. Which means that is usually guess the right side and overspecifying the solution.
Even then, there are some unknown factors that you can only get with a poll on the site (such as interference... channels used by your neighbors, prospective multipath, dead & such areas).
If you do not know how to make a good site survey, he would pay to hire someone who is long term. It is certainly an additional expense from the start, but the final deployment will be more likely to work in your / your customer expectations.
Once the system is installed, you can make a few tweaks and adjustments according to the measurements reported on the WLSE, but the primary configuration should not be based on a "good guess."
The number of users per access point is also slightly variable according to the type of application and the expected user traffic.
I saw thirty users as an absolute maximum, with as little as ten for use of heavy traffic. Generally speaking, somewhere 20 users per AP for common use would be a reasonable number.
If you have users or systems that will use the 802. 11 b, this number could be lower, since the PA must make accommodations for using 802. 11B and 802.11 g.
More details would be useful, but without a good site survey, no one can really give you a firm answer.
Good luck
Scott
-
1602i-e-k9 AP and WLC 5508 issue of Cisco
Dear forum participants,
I experience a problem connection Access Point 1602i-e-k9 to WLC 5508
I upack and taken an AP on the network, it appears on the WLC (monitor > all APs), I can see it using the link details for several time.
Then he desappears, restart does not help.
I searched the forum for solutions, made AP reset via command "cli rommon-like" + button "MODE" and "reset" . After that, the same thing happens again: he appears on WLC and disappears.
What I am doing wrong?
Brief info on devices and newspapers partial
Please see the full changelog of the AP attached (contains info after the reset command has been entered).
The AP Info
looking at the picture...
extracting information (283 bytes)
Image info:
Version suffix: k9w8-. 152 - 2.JB
Image name: ap1g2-k9w8 - mx.152 - 2.JB
The release directory: ap1g2-k9w8 - mx.152 - 2.JB
The iOS Image size: 9400832
Total image size: 9769472
Image device: Wireless LAN | LWAPP
Family pictures: AP1G2
Wireless switch management Version: 7.4.100.0
WLC Info
Name of the manufacturer... Cisco Systems Inc..
Product name... Cisco controller
Version of the product... 7.4.100.0
Bootloader Version... 1.0.1
Retrieving Image Version field... 6.0.182.0
Firmware version... Console USB 1.3, 1.6 Env FPGA, 1.27
Build Type....................................... DATA + WPS, LDPE
Journal of the AP
reset
[BEGIN] 20.03.2013 14:09:31
Are you sure you want to reset the system (y/n)? There
System reset...
Boot from flash
* 00:00:15.627 Mar 1: % LWAPP-3-CLIENTERRORLOG: Config flash load failed. Initialization of Cfg
* 00:00:15.631 Mar 1: % CAPWAP-3-Journal of ERROR: could not load the configuration of flash. Reset to the default configuration
* 00:00:16.671 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed to uplwapp_crypto_init: MIC present and analyzed successfully
No source of bridge-Group 1-learning
^
Invalid entry % detected at ' ^' marker.
% Without Gateway default route, if not an interface point, may affect performance
* 00:00:46.131 Mar 1: % CDP_PD-4-POWER_OK: all disabled radio - power INJECTOR_CONFIGURED_ON_SOURCE online source
* 00:00:49.411 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 172.17.254.6, mask 255.255.255.0, hostname AP0006.f618.1d3b
Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (172.17.254.1)
* 00:01:00.347 Mar 1: % CAPWAP-5-DHCP_OPTION_43: the 172.17.254.203 drive address obtained by DHCP
* 00:01:00.347 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.
* 00:01:09.347 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
* 00:01:19.347 Mar 1: % 3-CAPWAP-ERRORLOG: go join a capwap controller
looking at the picture...
extracting information (283 bytes)
Image info:
Version suffix: k9w8-. 152 - 2.JB
Image name: ap1g2-k9w8 - mx.152 - 2.JB
The release directory: ap1g2-k9w8 - mx.152 - 2.JB
The iOS Image size: 9400832
Total image size: 9769472
Image device: Wireless LAN | LWAPP
Family pictures: AP1G2
Wireless switch management Version: 7.4.100.0
Extraction of the files...
AP1G2-k9w8-MX.152-2.JB/ (directory) 0 (bytes)
extraction of ap1g2-k9w8-mx.152-2.JB/K5.bin (75790 bytes)
* 14:10:57.000 20 Mar: % CA
extraction ap1g2-k9w8-mx.152-2.JB/S2.bin (9328 bytes)
extraction of ap1g2-k9w8-mx.152-2.JB/S5.bin (106106 byte) PWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:10:57.539 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:10:57.543 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:10:57.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:10:57.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:10:57.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:10:57.543 Mar 20: % CAPWAP-3-Journal of ERROR: could not process the encrypted package capwap 172.17.254.203perform archive download capwap: / ap1g2 tar file
* 14:10:57.547 Mar 20: % CAPWAP-6-AP_IMG_DWNLD: not found required image on AP. image controller download.
extraction ap1g2-k9w8-mx.152-2.JB/info (283 bytes)
AP1G2-k9w8-MX.152-2.JB/HTML/ (directory) 0 (bytes)
AP1G2-k9w8-MX.152-2.JB/HTML/level/ (directory) 0 (bytes)
AP1G2-k9w8-MX.152-2.JB/HTML/level/1/ (directory) 0 (bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/forms.js (17492 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/appsui.js (563 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/ap_home.shtml.gz (1297 bytes)
AP1G2-k9w8-MX.152-2.JB/HTML/level/1/images/ (directory) 0 (bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/images/info.gif (399 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/images/cisco-logo-2007.gif (1648 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/images/background_web41.jpg (732 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/images/login_homeap.gif (19671 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/config.js (25507 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/sitewide.js (16554 bytes)
extraction of ap1g2-k9w8-mx.152-2.JB/html/level/1/officeExtendap.css (41801 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/1/back.shtml (512 bytes)
AP1G2-k9w8-MX.152-2.JB/HTML/level/15/ (directory) 0 (bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/15/officeExtendapBanner.htm (7114 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/15/officeExtendapConfig.shtml.gz (2864 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/15/officeExtendapSummary.htm (718 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/15/officeExtendapHelp.htm (5013 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/15/officeExtendapMain.shtml.gz (3350 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/html/level/15/officeExtendapEvent.shtml.gz (988 bytes)
extraction ap1g2-k9w8-mx.152-2.JB/K2.bin (5830 bytes)
extraction of ap1g2-k9w8-mx.152-2.JB/8005.img (200872 bytes)
extraction of ap1g2-k9w8-mx.152-2.JB/ap1g2-k9w8-mx.152-2.JB (9196955 bytes)
* 14:12:57.694 Mar 20: % 3-CAPWAP-ERRORLOG: white event 48 & combination State 10.
* 14:12:57.694 Mar 20: % 3-CAPWAP-ERRORLOG: SM Manager: failed to process the message of the timer. Event 48, State 10
* 14:12:57.694 Mar 20: % CAPWAP-3-Journal of ERRORS: do not handle the message from the timer.
* 14:12:57.694 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the message of the timer.
extraction info.ver (283 bytes)
Removal of target version: flash:/ap1g2-k9w8-mx.152-2.JB...done.
New image of the software installed in flash:/ap1g2-k9w8-mx.152-2.JB
System to use new IMA configuration
Flash event log entry: / event.log...
GE... done.
Download of archive: 212 seconds
* 14:14:28.389 Mar 20: upgrade successfully, the system image is now reloading
* 14:14:28.425 Mar 20: % SYS-5-RELOAD: reload requested by capwap image download proc. reload reason: NEW IMAGE DOWNLOAD.
* 14:14:28.425 Mar 20: % LWAPP-5-CHANGED: CAPWAP changed State to DOWN
Event.log written
Boot from flash
* 00:00:53.107 Mar 1: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 00:00:54.031 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 172.17.254.7, mask 255.255.255.0, hostname AP0006.f618.1d3b
* 00:00:54.107 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 00:00:54.163 Mar 1: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 00:00:55.163 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (172.17.254.1)
* 00:01:04.927 Mar 1: % CAPWAP-5-DHCP_OPTION_43: the 172.17.254.203 drive address obtained by DHCP
* 00:01:04.927 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.
* 00:01:13.927 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
* 00:01:23.927 Mar 1: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:16:30.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:16:30.539 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:16:30.539 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:16:30.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:16:30.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:16:30.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:16:30.543 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:16:49.211 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:16:49.211 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:16:49.211 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:16:49.267 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:16:49.287 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:16:49.287 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:16:49.303 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:16:49.343 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:16:50.287 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:16:50.335 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:16:50.343 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:16:51.327 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:16:51.335 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:16:51.379 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:16:51.387 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:16:51.395 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:16:52.379 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:16:52.387 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:16:52.423 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:16:53.423 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:16:59.343 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:16:59.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:16:59.539 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:16:59.539 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:16:59.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:16:59.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:16:59.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:16:59.543 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:17:17.699 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:17:17.699 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:17:17.699 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:17:17.755 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:17:17.771 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:17:17.771 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:17:17.783 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:17:17.819 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:17:18.771 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:17:18.819 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:17:18.827 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:17:19.811 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:17:19.819 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:17:19.863 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:17:19.871 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:17:19.879 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:17:20.863 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:17:20.871 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:17:20.907 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:17:21.907 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:17:27.819 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:17:28.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:17:28.539 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:17:28.539 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:17:28.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:17:28.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:17:28.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:17:28.543 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:17:47.203 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:17:47.203 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:17:47.203 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:17:47.259 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:17:47.275 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:17:47.275 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:17:47.287 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:17:47.323 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:17:48.275 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:17:48.323 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:17:48.331 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:17:49.315 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:17:49.323 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:17:49.367 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:17:49.375 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:17:49.383 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:17:50.367 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:17:50.375 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:17:50.411 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:17:51.411 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:17:57.323 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:17:57.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:17:57.543 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:17:57.543 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:17:57.547 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:17:57.547 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:17:57.547 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:17:57.547 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:18:15.699 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:18:15.699 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:18:15.699 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:18:15.755 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:18:15.771 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:18:15.771 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:18:15.799 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:18:15.831 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:18:16.771 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:18:16.835 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:18:16.843 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:18:17.827 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:18:17.835 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:18:17.879 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:18:17.887 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:18:17.895 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:18:18.879 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:18:18.887 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:18:18.923 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:18:19.923 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:18:25.831 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:18:26.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:18:26.543 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:18:26.543 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:18:26.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:18:26.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:18:26.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:18:26.543 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:18:44.699 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:18:44.699 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:18:44.699 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:18:45.163 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:18:45.183 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:18:45.183 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:18:45.195 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:18:45.227 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:18:46.183 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:18:46.231 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:18:46.239 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:18:47.223 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:18:47.231 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:18:47.275 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:18:47.283 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:18:47.291 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:18:48.275 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:18:48.283 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:18:48.319 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:18:49.319 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:18:55.227 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:18:55.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:18:55.543 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:18:55.543 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:18:55.547 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:18:55.547 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:18:55.547 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:18:55.547 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:19:13.695 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:19:13.695 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:19:13.695 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:19:13.751 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:19:13.767 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:19:13.767 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:19:13.783 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:19:13.815 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:19:14.767 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:19:14.827 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:19:14.835 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:19:15.819 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:19:15.827 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:19:15.871 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:19:15.879 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:19:15.887 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:19:16.871 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:19:16.879 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:19:16.915 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:19:17.915 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:19:23.815 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:19:24.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:19:24.539 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:19:24.543 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:19:24.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:19:24.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:19:24.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:19:24.543 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:19:42.695 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:19:42.695 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:19:42.695 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:19:42.751 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:19:42.767 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:19:42.767 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:19:42.783 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:19:42.815 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:19:43.767 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:19:43.815 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:19:43.823 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:19:44.807 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:19:44.815 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:19:44.859 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:19:44.867 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:19:44.875 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:19:45.859 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:19:45.867 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:19:45.903 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:19:46.903 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:19:52.815 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:19:53.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:19:53.543 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:19:53.543 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:19:53.547 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:19:53.547 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:19:53.547 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:19:53.547 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:20:12.111 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:20:12.111 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:20:12.111 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:20:12.167 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:20:12.183 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:20:12.183 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:20:12.199 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:20:12.231 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:20:13.183 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:20:13.235 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:20:13.243 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:20:14.227 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:20:14.235 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:20:14.279 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:20:14.287 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:20:14.295 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:20:15.279 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:20:15.287 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:20:15.323 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:20:16.323 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:20:22.231 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:20:22.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:20:22.543 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:20:22.543 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:20:22.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:20:22.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:20:22.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:20:22.543 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:20:40.699 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:20:40.699 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:20:40.699 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:20:40.755 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:20:40.771 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:20:40.771 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:20:40.787 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:20:40.819 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:20:41.771 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:20:41.819 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:20:41.827 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:20:42.811 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:20:42.819 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:20:42.863 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:20:42.871 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:20:42.879 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:20:43.863 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:20:43.871 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:20:43.907 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:20:44.907 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:20:50.819 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:20:51.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:20:51.539 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:20:51.539 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:20:51.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:20:51.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:20:51.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:20:51.543 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
* 14:21:10.107 Mar 20: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (UNKNOWN_MESSAGE_TYPE (5))
., 1)
* 14:21:10.107 20 Mar: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
* 14:21:10.107 Mar 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.17.254.203:5246
* 14:21:10.163 Mar 20: % CLIENTERRORLOG-3-LWAPP: LWAPP LED Init: incorrect led State 255
* 14:21:10.179 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 14:21:10.179 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed state down administratively
* 14:21:10.191 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:21:10.227 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:21:11.179 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:21:11.227 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to down
* 14:21:11.235 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio1, changed State to reset
* 14:21:12.219 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:21:12.227 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio1, change of State down
* 14:21:12.271 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio1, changed State to
* 14:21:12.279 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
* 14:21:12.287 Mar 20: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 14:21:13.271 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed State to
* 14:21:13.279 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 14:21:13.315 Mar 20: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
* 14:21:14.315 Mar 20: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 14:21:20.227 Mar 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
* 14:21:20.000 Mar 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.254.203 peer_port: 5246
* 14:21:20.539 Mar 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.17.254.203 peer_port: 5246
* 14:21:20.539 Mar 20: % CAPWAP-5-SENDJOIN: send request to join 172.17.254.203
* 14:21:20.543 Mar 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
* 14:21:20.543 Mar 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
* 14:21:20.543 Mar 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
* 14:21:20.543 Mar 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 172.17.254.203 capwap
[END] 20.03.2013 14:21:55
Azim,
I wonder if the regulatory domain of the AP is correct.
Please provide the result following (authorization according to Leo)
1 WLC: sh sysinfo
2 PA: sh version
3 PA: HS inventory
Thank you.
Amjad
Rating of useful answers is more useful to say "thank you".
-
How to install without Internet connection?
I have CS ^ and the hard drive failed, I need to reload. Impossible to use cloud as mini is in the RV and rarely do we have a reasonable internet signal.
Can seem to find a way to tell it to Adobe.
So... what happened to your original install disks?
Adobe provides more disks, but you can download it on another computer and copy it to a USB key... you WILL need an Internet connection to activate after entering your serial number
Download & install instructions https://forums.adobe.com/thread/2003339 can help
-includes a way to go to a page to download the Adobe programs if you do not have a disk or drive
-you will need to enter your original serial number during the installation for non-Cloud programs
-Cloud desktop http://helpx.adobe.com/creative-cloud/help/creative-cloud-desktop.html
-Cloud Getting Started https://helpx.adobe.com/creative-cloud.html
-Membership questions and problems https://forums.adobe.com/thread/1146459
- or kglad links in response to #1 here can help https://forums.adobe.com/thread/2081216
Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq
-
MY imac is around 14 years it freezes a lot and seems to heat there is also a white line appears on the screen
spec is imac4, 1 speed2GHz, memory 2 GB can it be fixed or is it old, cheers
Probably this model
http://www.EveryMac.com/systems/Apple/iMac/specs/imac_cd_2.0_20.html
You can try these two procedures
Reset the management system (SCM) controller on your Mac - Apple Support (see Reset the SMC on Mac desktops)
How to reset the NVRAM on your Mac - Apple Support
This design has an area of wind on the lower edge of the carcass from which the internal fan draws in air (cooling). Visually check this area for dust accumulation that may block the flow of air, which could be the reason for the "heat up".
The line running across the screen may be a hardware problem, if you see immediately after a restart, while the iMac is still putting into service.
-
Where is my book of e-mail and archived address?
For other reasons (impossible to open web pages) I did a Recovery MS where he stated my personal data would be spared. Some points need to be recharged, but the data must remain.
I use Mozilla for a few years (great program, BTW) and had created an address book and records of received emails that I had archived according to the Member of the family.Since the complete recovery step I re-installed Mozilla. He worked and shot the new email to my EarthLink account. I would now like to re - install the address book and my archived e-mail records assuming that they're always around.
Create a new profile as a test to see if your profile is the source of the problems.
If the new profile works then you can transfer files from a profile already used in the new profile, but be careful not to copy files corrupted to avoid transporting on the problem
-
Store.e TV + - error, and green color
My Store.Tv + have a mistake. When turn on, select HARD drive and select a video file, the green color of the screen TV and Store.e TV + Reload, is impossible to use. HDMI cable and RCA cable used.
Help?Hey,.
> Cable HDMI and RCA used cable.
This means that you have already tried different cables?
It would also be my suggestion tests different cables because if the TV changes the color all it could be a broken cable.This occurs with all types of files, or only with a certain file?
What you can do is to reset the box to factory settings and test again. If this isn't the case, it looks like a hardware malfunction.
-
BitLocker Drive preparation tool - fail
Hello
So, I try to activate bitlocker on my laptop drive encryption, which is already running Vista Ultimate x 86. I was not initially intended, and I knew that if I wanted to later, I could allagedly use the Bitlocker Drive preparation tool, so I built it with a single partition.
Now, I want to activate bitlocker, so I downloaded the drive preparation tool, but I when I run it, I get the following error:
"The bitlocker Drive Preparation Tool cannot find a system of target drive. You may need to manually prepare your drive for BitLocker. »
So I search and find this article kb http://support.microsoft.com/kb/933246
I tried to manually specify the system drive by running the command line: ' BdeHdCfg.exe - target: shrink - newdriveletter x: - size 1500-quiet - restart ", but she just runs for a few seconds and then returns to the command prompt, so I check the event log and find an entry under the logs event observer, applications and services, Microsoft, Bitlocker DrivePreparationTool, Admin and found events (event error 1 id) similar to what I saw in the GUI of not find a system drive. Under the operational event folder, I found event ID 4104, "a volume did not meet the requirements for a target volume. Volume: C: reason: impossible to reduce the target volume of the requested size. "
So in the above article, my error message with certain proposed resolutions: "temporarily disable the hibernation option and disk paging. Then, use the Windows preinstallation environment to remove the file Hiberfil.sys and Pagefile.sys file. Restart the computer in Windows Vista. Then run the BitLocker Drive preparation tool. "OR"reinstall Windows Vista. »
So of course, I tried the first suggestion, disabling hibernation using "powercfg-h" off and delete the hiberfil.sys file, disabled a swap under System properties file and deleted the "pagefile.sys" and restarted.
Always the same error :(
Is the second action plan 'Reinstall Windows Vista' serious? I want to activate the drive encryption, should not be this hard. I don't think that requiring people to reinstall just because an application cannot function in a reasonable way to be an excuse...
Hi benneh,.
In the article you posted there are two different scenarios listed that could cause the error message:
"The bitlocker Drive Preparation Tool cannot find a system of target drive. You may need to manually prepare your drive for BitLocker. »
In your post you referenced scenario 2 and the steps you took to solve it, but you reference scenario1 which is as follows:
Scenario 1: You do not have enough free disk space to "at least 10 percent of the active partition must remain free after the partition size is reduced by 1.5 gigabytes (GB). To resolve this error, move the files to another partition or delete files. »
Just to be sure that it is not the reason for your question; After subtracting the reduction in size of 1.5 GB for your total hard drive space always need it the 10 percent of free space on the active partition? Please let us know. Thank you.
Shane
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
Vista not loading - just get a white screen with the mouse pointer
Hi using Vista for a while now, 4 years, no probs real. Then two days the PC crashes, and trying to restart the option repair (recommended) came, or start Windows normally, selected repair option, opens Windows screen, then a mouse pointer and that is it, have tried all the options by using the form F8 but never went to the same point, can not use safe mode , don't be filled disc no at all to repair or reload. Impossible to get even at command proment unless I'm missing a way to get this up on the screen.
Help please,
Hello
1 him comes from the operating system that is pre-installed on the computer?
2. do you get an error message when you try to start in safe mode?
You can turn off all external devices (except the mouse and keyboard), and then try to start.
If you are able to start in safe mode, you need to get a windows vista dvd to solve the problemIf you are able to organize a windows vista dvd, you can perform a startup repairYou may also contact the computer manufacturer to obtain a windows vista dvdSee also the link to learn more:What to do if Windows does not start correctly -
Start PC laptop Toshiba in safe mode, only displays black screen, will not respond to any commands.
Hello, I recently tried to do an advanced start safemode, because when I tried to do safe mode by pressing F8 it would have not responded to the command. Then I did a MSconfig, lit manually in safe mode, so I can then restart and do a scan to search for viruses or hackers of air because he had a reason to suspect. Now, after the manual switch, when I rebooted all I get is a black screen. No logo, nothing. When I press the buttons for the controls at first upward, it beeps at me and that's it.
Done, I have XP, not Vista, don't know if it makes much difference or not, but that's exactly what I did.
Is went to start, click Run, type msconfig, went to the utility system configuration, general tab selected, then the system of services. Then selected drivers devices of loading at startup Safemode-minimal database, and then click OK. Then, the computer said I had to be logged as administrator for these changes to take place and to connect and make changes. I was already logged as admin. so I advanced and restarted the computer and that's when I got black screen, no splash screen, no logo, no cursor.
I just read that I could have possibly messed up by not checking the VGA mode in order to be able to communicate in this mode, I don't know if it is correct or not.
I have my recovery discs, I've tried this morning, following their directions and it will not respond to one of these orders either.
I don't understand, why... it was working fine before I did it, but like I said I suspected a virus or a hijacker, but my Norton 360 and SuperSpyware nothing not detected in normal mode. That's why I tried to safe mode.
Here is the vista forums
Try the forums xp on the link below
http://answers.Microsoft.com/en-us/Windows/default.aspx#tab=4
Answers by topic
- Office & Customization
- Files, folders, & search
- Game
- Hardware drivers &
- Install, upgrade, and activate
- Internet Explorer
- Music & Sound
- Networking, mail, electronic, & updated online
- Maintenance & performance
- Photos & Video
- Programs
- Security, privacy, and user accounts
- System repair & recovery
- TV and movies on Windows
- Windows Update
Walter, the time zone traveller
Maybe you are looking for
-
I accidentally delete interface wifi
As the title says I delete it while I was trying to solve the slow connection, I had Now I don't know what to do, the hours looking for a solution, but nothing...
-
my iPhone 5s did pay almost 3 days in a row and has not lit, what should I do?
-
Help, please!
-
Need for clarity around application transitions...
Well I'll start another project of app, but this time I want to jump completely under the user BB10 interface. That being said, I had a simple NOOB question. Feel free to direct me to any message that is already existing on the subject. But I'm cur
-
Support for multiple versions of an application
Hello If I have an application that has complained about the os 5.0, but uses of the Mineral which are not available on os4.7. Can I change the code base is compatible 4.7. But the app to 4.7 compliance of refactoring removes some of the features of