AIR-LAP1042N-N-K9 in standalone mode? FIXED *.

Similar Questions

• Are there special procedures when I update mode NX - OS (standalone) mode ACI of NX - 9 K?

  Hello world

  I have two questions.

  First of all, are there special procedures when I update mode NX - OS (standalone) mode ACI of NX - 9 K? For examples, NX - OS version, cards online, EPLDs, licenses and so on. And is it possible back ACI mode mode NX - OX, too?

  Secondly, I know that fabric module (below, FM) s are paired FM1 and 2, 3 and 4, 5 and 6, respectively when there are 48-Port 1 / 10 G T/F Module in the chassis. In this case, if the FM in slot 2 to lose, both links to slots 1 and 2 would be lost because the mux detects the loss of slot 2 and therefore takes traffic slot 1 also, that is, the slots are paired. If so, what are the benefits of an investment FM full? Please share your knowledge with me clear ^ ^

  All your help will be appreciated.

  Paul

  Paul,

  Sorry for the delay... Answers to your two questions.

  1. FM can go in one of the remaining slots. The line cards have Muxes them bound to each FM which is "installed" in the switch.

  2. you original question was related to the switches in the mode of the AIT.  As of today, there is limited line cards that operate in mode of the AIT.  3 FMs provide the necessary conditions for the rate of the line more most of the previously mentioned such line cards.  That said, once you install a N9K X9736PQ a minimum of 6 FMs are needed.  So if you have a failure on one FM, your BW system in the tissue deteriorates. The BW is shared across all line cards until the failed FM is replaced.

  T.

• Latest AIR to support the desktop GPU mode?

  Hello

  Does anyone know the latest AIR supporting the desktop GPU rendering mode?

  Thanks in advance.

  I created an application to be able to use the GPU mode for the desktop publishing. There are tons of applications using the GPU on mobile and I think that many developers want to should be able to publish the steam with the same performance.

  I would appreciate your vote for this feature!

  The desktop publishing (steam) mode characteristic rendering #4145057 - GPU!

  Thank you!

• Cisco AIR-CAP3502I-A-K9 can be used in standalone mode?

  Hello

  We strive to deploy AIR-CAP3502I-A-K9 with 5508 controller. However, the controller is remaining and we do not want to delay our site survey. Can we use the AP mode stand-alone for the poll on the site? We don't need to exploit or to pass traffic. As long as he can feed himself which is detected by Ekahau Site survey tool, I'm fine. I can power via a PoE switch.

  Thank you

  You can use it as a regular standalone access point without restriction. Need to download this code and convert CAPWAP IOS autonomous Yould:

  ap3g1-k9w7 - tar.124 - 25d.JA.tar

  You can find instructions how to do the conversion on the Cisco site

• MacBook air does not start in safe mode

  Hello

  I have a MacBook air 2015 and my disk got full and now I can not connect with my user. The progress bar stuck at 100%, and the system won't let me connect. I have read that I need to start in safe mode but I can't do it. My MacBook does not sound at startup and even if I press the SHIFT key the system takes me to safe mode. The only thing I can do is to go into recovery mode.

  Can someone tell me please in the right direction.

  You can use target disk Mode to access the MBA:

  https://support.Apple.com/en-us/HT201462

  When you delete or copy files on the MBA, remember to empty the trash.  Then only the space is allocated for the new data.

  Ciao.

• HP Pavilion g6-1313sh Notebook: dual Radeon graphics card - cannot enter bios mode fixed

  Hello!

  I recently bought this laptop apart from my friend and is struggling with this for a few weeks now.

  I was on the forum every day for a few hours without result.

  so, my laptop is HP Pavilion 1313sh g6 with Win7. I have the latest version of the bios, so I could put my gpu bios mode set instead of dynamic.

  Here's the problem... When my setting was dynamic, I got the "switchable graphics" option and I could put the preset by application. as many people pointed out, it really does not work, so I went back to fix.

  This option is now missing. so I tried in CCC, following this: http://support.hp.com/us-en/document/c03048374 in the fixed bit.

  It is, I have no change option... I only get the graphics card AMD Radeon Dual 'activate' or disable... but not the button to switch permanently to the highest performance card... checked in CCC, it recognize my 2 cards under hardware (1st HD6520G 2nd is Hd7400M).

  I start to tear up the rest of my hair. Please can someone tell me what I miss? as said, the most recent drivers from the site is all settled.

  Thank you!

  Hi @SmokeyJohnny ,

  Thank you for visiting the Forums HP's Support and welcome. I looked in your question about your HP Pavilion g6-1313sh Notebook and issues with graphics switchable. You can do a System Restore. System Restore will help if something is automatically updated and wasn't on the laptop.

  When running a system restore note remove all USB devices. Disconnect all non-essential devices because they can cause problems.

  If this does not resolve the problem would be to uninstall the graphics drivers listed in your device manager. Reboot the laptop and it must be reinstalled the proper drivers. Yours is the AMD Radeon HD 6520 + 7450 Mr. here are your drivers if you need.

  I hope this helps.

  Thank you.

• HP 15-d020ek Mode fixed!

  Hello!

  I have a simple question. Is the "HP 15-d020ek" the option in the Bios to choose between 'Dynamic' & 'Fixed' mode for graphics switchable (I think he has Intel HD 4000 and Nvidia 820 M)

  I really need to be sure about this before buying the laptop, because I need especially for the games.

  Thank you.

  Hi Huntrz,

  To answer your question directly, not the "Dynamic" vs "Ch" configuration is not controlled at the BIOS level.  The switchable NVIDIA Graphics implementation is controlled entirely by the software.

  That is provided by NVIDIA Optimus technology is an option that you can take a look. I have included the link 'NVIDIA OPTIMUS'.

  I hope that answers your question.

• Restart in safe mode fixes my problems. How to diagnose the source of the problem?

  Drop-down menus do not work. I type and nothing shows in the drop-down list. I select something, and Firefox crashes without showing the selection. If I maximize full page, he says. If I type in the same or another dropdown menu, even when it does not, until I reduce the page.

  Restart Firefox in safe MODE and everything works fine. Reboot in normal mode and problems reappear.
  How do I diagnose what is causing the problem?

  Hi Billamicasr

  first try to disable hardware acceleration and check again

  See also: extensions, themes, and issues of hardware acceleration to resolve common troubleshooting Firefox problems

  Thank you

• No air-conditioned WRT1900AC option in network Mode

  I have a few AC supported devices and thought that I would spend my router only AC mode on the 5 GHz network to find the drop-down list offer, mixed, a/d, n, options. Is there some type of extra necessary step to get the CA appears, or am I missing something?

  "a/n only" is the Protocol of the AC.

• How to convert an AP 1700 / 2700 light mode to standalone mode?

  I know that support AP1700/2700 unified by version 15.3.3 mode.

  http://www.Cisco.com/c/en/us/TD/docs/wireless/access_point/15-3-3/configuration/guide/CG15-3-3/CG15-3-3-Chap1-overview.html

  But I couldn't change the mode because of the following error.

  AP1c6a.7a92.5468 #CAPWAP autonomous ap

  Convert a stand-alone image. Move forward? (yes / [No.]): Yes

  No found stand-alone image! The conversion failed.

  Why this error message displayed? Please tell me how I can solve this problem.

  Thank you.

  Atsushi

  According to me that ap1700 can start using a light image which is on the page of downloading software for AP2700/3700.  Is this correct?

  Yes, that's correct, according to this 1700/2700/2600/3600/3700 all have the same image starting with "ap3g2-xxx '.

  http://www.Cisco.com/c/en/us/TD/docs/wireless/access_point/iOS/release/notes/RN-15-3-3.html#32237

  Ap3g2

  1700I 2700I/2700E, 2600I/2600E, 3600I/3600E, 3700I/3700E

  HTH

  Rasika

  Pls note all useful responses *.

• AIR-LAP1042N-N-K9 without command configures

  Hello world

  I have a couple of these nine APs but apparently through the CLI (serial connection) I can not put the command "configure." I access mode privilege with the password, but after that I can't do anything.

  Most I've seen on the cisco site that for the first 5 minutes, that it should give the ip address 10.0.0.1 and the Browse... but I tried 10.0.0.20/24 and nothing.

  This is the first time that I have set up, you can suggest something?

  Thank you.

  Hello

  the AP is LWAPP and WLC get this operation does not require... To enter the Conf t terminal, we need to reimage the firmware of the AP to the stand-alone image and the link below will help you out in getting a result...

  https://supportforums.Cisco.com/docs/doc-14960

  Let me know if this naswered your question and please do not forget to sort the useful messages!

  Concerning

  Surendra

• Not able to connect to essbase in standalone mode

  
  Hi all

  I installed essbase 11.1.2.2 in stand-alone mode. After the installation of the services are running. I tried to connect to via \user_project\epmsystem1\EssbaseServer\essbaseserver1\bin < EPMHOME > maxl essbase. But he failed because of invalid connection. I'm in the name (ID epm_admin PWD xxxxx) password which I entered during Setup. Am I missing something?

  Concerning

  SB

  No, I guess that answer at the bottom of the post:

  https://forums.Oracle.com/message/11004659

• How to keep the tables in mode fixed?

  Don't know about you but I'm not used to the fact that available in many 3.5.3. moves horizontally and vertically. It distracts me a lot, especially with the touchpad on my Macbook Pro. Is there a way to get rid of this automatic void of white on the sides and bottom. If the table is small, there is no need to make "wobbly", don't you think?

  Someone at - it an idea?

  Hi BassPlaya,

  I think that what you are wanting to do is to reduce the size of the painting that arrays of numbers are sitting on.

  As I know there is no way to do. You can drag the table upwards and to the left, but do not stop when the yellow guides appear or hide you the first lines/colomns and be unable to view/edit the.

  I found this problem bothers me is no longer on the Mac-I set my scroll automatically.

  Quinn

• I can force an AP Flexconnect in standalone mode?

  I found an interesting setup where some remote sites have more 400 + ms latency to the controller (because of the 3 G WWAN connection / 4 G with Corp.), I think causing a few problems since the latency required for Flexconnect is not more then 150 + MS it seems if I block traffic CAPWAP lap to the controller and force everything to be locally switched these problems disappear. So I was wondering if there was a way I can force an AP Flexconnect as a stand-alone, I wasn't able to find anything in any documentation that far.

  I have planned an upgrade to 7.4 (from 7.2) to gain the ability to apply an ACL Flexconnect to force all either locally switches at remote sites in the ROUND, but I was just looking for a 'better' stop gap in this ideal design at least.

  --

  CCNP, CCIP, CHRC, CCNA: Security / Wireless
  Blog: http://ccie-or-null.net/

  No.... If the Wan is the question, yes I see him causing problems with the AP in the worst case scenario.  If the amount of the fine when you block udp 5246 and udp 5247, I would say that is the only work autour.  I know there is a setting for the FlexConnect where you can activate the link latency:

  http://www.Cisco.com/en/us/docs/wireless/controller/7.0/Configuration/Guide/c70lwap.html#wp1344052

  Thank you

  Scott

  Help others by using the rating system and marking answers questions as 'response '.

• PES 10 times Organizer and editor crash on multi-core hardware. set the processor affinity unique mode fixed

  As I pointed out in thread http://forums.Adobe.com/thread/941128 I found the editor and organizer for PES 10 crash in basic multi environment, I'm WIndows 64 bit, latest updates (including sp1), I had the same problems with Windows 7 32-bit.

  Workaround is to set the affinity to a single processor.  From the Task Manager, select the "processes" tab, find the exe (for example PhotoshopElementsOrganizer), right click, select "set affinity...". "and reduce the number of CPUS selected (checked) for a single.  (Under different versions of Windows specific means vary, but the basic steps are the same).  It doesn't matter what cpu choose you, but if you are the editor and organizer, put it on different processors.

  Pretty much everything these days being multi-core material, my hypothesis is that Adobe test in a virtualized environment and therefore do not discover this type of unreliabillity.  Adobe really need to test their software further exactly the same problem exists in PSE 6, is hardly new to them.

  The solution is in what precedes.

  If Adobe read this, they should take note that a virtualized environment does not provide a decent systems CPU multi-core fidelity emulation.  The ONLY way to test the reliability of an application is on REAL hardware.