all-in-one Pavilion 23 bo37c

Similar Questions

• 23 all-in-One Pavilion: a Factory Reset also renews the recovery Partition?

  I just did a Factory reset on my 23 all-in-One Pavilion. Previously, in the past, I had inadvertently erased the recovery disc. Fortunately, as I just discovered in the rebuilding process, I did a flash backup restore.

  (1) now that I have to order, updated to 8.1 has done that also recover this recovery on the hard disk drive.

  (2) the last time I did the flash recovery he had only windows 8. Now that I have 8.1 on that I should make a new flash with window 8.1 on this recovery?

  I know that last time I did restore flash he reported that it was a matter of time. Could not do another restore backup discs or Flash after this one. So I suspect that if the recovery disc has not been restored too it does not allow me to make a new key USB recovery stick?
  
  Thank you!  Jack {":-Dx}

  I ALWAYS KUDO AND MARKED RESOLVED. It is THE RIGHT THING to DO... doncha know. «  :-D
  Find thumbs upward, then click on to a KUDO
  Look to the right and see the OPTIONS to mark ACCEPT as a SOLUTION. Thank you!

  I think I found the answer elsewhere here. Here, it is cut and pasted the answer is in the first sentence!  Jack {":-Dx}

• 23 all-in-One Pavilion: Pavilion 23 AIO display dims

  I have a Pavilion all-in-one 23 and the screen guard sponsorpark. He did since I was in about 2 months ago. It's as if she's about to go to sleep, can still be seen on the screen. Sometimes it flashes between normal brightness and dim, dim sometimes and other times he has normal brightness. I have restarted and disconnected, but it did not help. I rest the factory settings screen (even if I haven't changed anything). I also checked the "power plan", the value balanced now. In "standby" mode, it turns off the monitor after 10 minutes and 20 to put the computer to sleep. Anyone have any ideas?

  Hello @KevRPh,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post on how your AIO desktop computer screen darkened intermittently, and I'd love to help you!

  To restore the eating patterns of your desktop by default, I advise you to follow the steps below:

  Step 1. Click the Start button
  Step 2. In the search box, type "Command Prompt"
  Step 3. Right click on command prompt

  Step 4. Click on run as administrator
  Step 5. At the command prompt, type powercfg /restoredefaultschemes and press enter

  reference: http://superuser.com/questions/669571/Windows-8-1-64-bit-power-schemes-gone

  If the problem persists, I also suggest reinstalling the drivers software and hardware of origin provided with your computer. This can be done by following the steps described in this document on the use of the Recovery Manager to restore the software and drivers (Windows 8). To update this software, please follow this resource using HP Support Assistant (Windows 8).

  Please re-post with the results of your troubleshooting, and I look forward to your response!

  Concerning

• 23-1000 all-in-one Pavilion: mouse and keyboard stop working

  I had my all-in-one since end of February 2016 - bought at Best Buy local - touch screen pc works still but don't do me any good because the mouse and keyboard do not work after 3 months of excellent performance.  Both have new batteries.  Can be signal problem because I've set up wireless.

  Help - frustrated and have no idea what to do.

  Thank you

  Terry Anderson

  Hello @MaggiesMimi,

  Thank you for visiting the Forums from the HP Support! The forums are a great place where you can find solutions for your problems, with the help of the community!

  I read your post on the issue of the keyboard and the mouse.  I understand that they both stop working recently, and you have already replaced the batteries.  I can certainly help you with this!

  First of all, try to review the following document and let me know how it goes:

  HP PC - keyboard and wireless mouse troubleshooting

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• 27-a010 all-in-One Pavilion: why the hard drive from my old computer Toshiba displayed on my new HP c drive?

  I got this new computer on Monday. The reason why I bought a new was that I suspected that my old Toshiba got compromised. I even bought a new Linksys router that was AC 1900. My new HP computer has McAfee and uses MicrosoftEdge browser. There are several interesting questions, I hope that experts from HP can answer for me.

  1. why my old Toshiba drive appears on the hard drives in the Device Manager?

  2. Why are there readers D two on disk management? Can't update my Windows 10. I bought a new computer.

  3. why hiberfil.sys and pagefile.sys, swapfile.sys, BOOTNXT appear on my drive C Windows?

  The above synptoms are normal? I need to do something about these questions or just leave them along? I have a microsoft all in one account.

  Thanks for the reply.

  Hello

  I don't see your screen but:

  1. new machine uses Toshiba HDD, not your old machine of Toshiba. HP uses HARD disks with many suppliers, including Toshiba.

  2. Yes, it is normal. One with the file system is the real, without file system is a shadow one.

  3. normally, they are hidden system files, you can hide them if you wish.

  Kind regards.

• All-in-one Pavilion 23 23-b034: 2 try to install the solution Center HP for printer HP Pavilion has failed. Screenshots

  I had to do a cover of the factory recently. I can print with the HP C7280 programs smoothly. I got this printer and the solution Center works on this pc before the resumption of the plant and another pc before that.  I tried to install my printer HP all One Printer Solution Center now twice with today fails. I hope that the help of screenshots.

  I 1) downloaded a complete new installation - 2) off all antivirus - 3) restarted and restarted the printer HP - 4) the fact that all windows updates have been applied for windows 8.1 - 5) tried after the provided HP solutions but always with failure. Installation all the way to the final "device configuration"... and then expires. Thanks for any help.

  

  

  I ALWAYS KUDO AND MARKED RESOLVED. It is THE RIGHT THING to DO... doncha know. «  :-D
  Find thumbs upward, then click on to a KUDO
  Look to the right and see the OPTIONS to mark ACCEPT as a SOLUTION. Thank you!

  RnrMusicMan: (btw, former musician of Navy for this purpose) I need to send thanks a lot for your answer. I have tried, almost to the point of questioning my sanity, too many times tried too many things and all have failed. Why not go and buy a new printer? Financial considerations. Here's what I've worked with... (finally a good result there, at least the best I know for the moment at the end)

  (1) start here, I have an older HP all C720 printer wireless. I do not think at the moment there is a download of the full version which will allow him to install it in a machine of 8.1. An 8 machine if necessary, but not a 8.1 I do not...? That's what I gathered. Where I made my mistake, so, I was this old horse to battle C7280 installed on my newer HP Pavilion and worked very well with 8.1, (read on before thinking 8.1 work with the C7280) when I say great worked, I mean the Solution Center has worked. Then after a while I improved the Pavilion to 8.1 and everything was fine. A couple of weeks, I had to do a cover of the plant on the HP Pavilion. Instead of installing the software of the printer with the center of solutions right then while he was still an OS 8, I upgraded to 8.1 Loaded my favorite of all the programs and tweaks and tricks. Then I said, I'll install the old workhorse C7280. It would not, not at all, regardless of how many tips I read here, and Googling. Then I tried to install the full version of XP on one of the XP machines. No go. Something I said is prevention. Who could know. I tried to purge the XP what I knew could be related to HP. Shut off all antivirus programs, download fees, etc. etc. ad naseum. I have read and read and tried and failed and failed. You get the drama.

  So, I decided that if I could get it on the Acer Aspire one Netbook I could use as a slave, small sorta Acer server. I barely use the netbook anyway. So I couldn't do. Frustration. So I decided JUST ONE MORE ATTEMPT. And here's what I did for Acer.

  I did a factory restore. No former antivirus autour. Nothing is added. Presitine and already had Service Pack 3 with the resumption of the plant.  What follows I have none to little idea of his touch, but that's what I did.

  (2) I have an old modem that I had used as a slave of my new modem D-Link. I got it, because many of my devices will not work on the new 'n'.  I think, old modem old printer, old BONES. I have set the printer to get the old o SSID of the slave and agreed which has no password. Fortunately, I know anyone personally that could use this wireless slave and they all have their own.

  (3) so once again, I downloaded the full version of XP on the netbook. Extracted, he ran, and so he went the full installation and works.

  That's a lot, but I'm a cheap guy who hates to throw even if old devices, good. I use this Chrome extension called Extension Office remotely in order to get on the netbook from any computer and print using the Solution Center.

  I don't know what I did but I know I've worked. So this is my solution. I'm sure some could find another work around, but probably way above my paygrade.

  Once again, thanks a lot for taking the time. I think I followed your solution several, much too long and did not work. Unless I was always doing something wrong.  My solution was radical but it works for me always try to use these appliances. I just take good care of them and they last. My most recent is the HP Pavilion and it's going on 2 years now.

  Differences or questions please ask. 'Jack :-{D '.

• All-in-one Pavilion 23 23-b034: when upgrading your OS Version, can you do a new recovery disk?

  I have a HP Pavilion bought with Windows 8 and improved to 8.1

  Hello

  No, you can create ONCE and the recovery/backup media will bring your machine to factory settings (IE Windows 8) and that you need to update again. The game you created restore the recovery partion.

  Kind regards.

• 20-b010 Pavilion all-in-one: Pavilion 20-b010

  How can I remove the RAM 4 GB (Im assuming that its 2 2 GB chips) and add chips memory 8 GB (2) to MAX Out?

  It should be combined?

  He can't find the diagram of the where there is in all that in a single computer.

  Please send the link to me or the diagram.

  Thank you

  [Personal information]

  It is in several languages, but the pictures speak for themselves. See Page 18

  Manual

  More information

  Modules of DDR3-1333 laptop consumes 2 x 8 as you have already understood.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• All-in-one Pavilion 23-Q227C: HP install and download Assistant does not

  Whenever my computer starts up, the HP download and install the wizard tries to run to download a driver Realtek (SP74157) and HP Support Assistant (SP71727).  It fails each time, with a pop up that says "installation HP and download Assistant works do not" and the only option is to "close the program".  Don't know if these downloads are important, but their failure every time is, at the very least, a nuisance.

  Solutions?

  @ericbro

  I'm not aware of a program that runs on the HP of other consumer computers that the HPSA who would try to install an update for your driver Audio HP's.

  • If you remove the HP Support Assistant to programs and features,
  • If you stop and restart the computer from a STOP condition (not restart),
  • who should squelch (stop) the HPSA and no subsequent download / install primed by the HPSA

  If the process is repeated even after the removal of the program and by completing a cold (boot off) start, then installation must be controlled with other than the HP Support Assistant (as you say).

  The Task Manager will appoint the HPSA program when that program (HP Support Assistant) is open (click program and run).

  The Task Manager > Details will appoint the program (HPSA) as "HPSF.exe' (executable for the HPSA).

  If the HPSA is the process that is continually download and try to install the driver, you might have to search in the list of processes (Task Manager > Performance > resource monitor) and see if you can find the rogue program.

  I think that if the driver is to download somewhere on the network, you would see a relative link / address in the resource monitor.

  I may have missed something, of course...

  If I think of anything else, I'll post.

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  Fixed / responded? Click this post accept as Solution to help others find answers.

• Multi-card reader don't like to give back the cards Memory Stick Duo Pro 23 Pavilion all-in-one

  I want to just make sure I don't do something wrong.

  When I plug it into a SD card seats when inserted about 2/3 of the way into the slot and I can easily put my fingers on it to remove it when it's time to take it out.  When I plug the Memory Stick Duo Pro that is not recognized until it is at least inserted 9/10 and I can push completely rinse with a case and am not sure that it has bottomed out or not.  It works fine, but now it is not removable without the use of pliers tweezers.

  Is this normal behavior and waited for the mult card reader integrated into 23 all-in-one Pavilion?

  I have a more than adequate solution.  I plugged in the little USB card reader that accepts MS Pro Duo in their own homes. This post is therefore more closely to ensure that I'm not missing something obvious.

  My guess is that the drive or the motherboard was designed for the case to be a little closer it is.

  Hello @MarksPavilion,

  I understand that you have problems, remove the Memory Stick Duo Pro card reader that he will not jump out far enough to catch. The problem you describe seems to be a physical problem. Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html.
  
  I want to thank you for display on the HP Forums. Have a great day!

• Pavilion all-in-one Q214 23: factory restore on the new HP Pavilion all in one computer

  I have a week 6 old Pavilion Desktop all-in-one.  I wanted to do a factory install on it because I had a lot of extra things that I don't want anymore, I installed and I thought what a factory restore would be better.  I went to the HP Recovery Manager and no where in the choices he said 'factory restore '.  He used to have this option in the HP recovery environment.  I checked all the options and nothing on the factory restore.  I made a set of recovery discs, but I always remember that HP still had the opportunity to do a factory restore.  I have tried F11 and F8 and no luck.

  Answers or suggestions will be greatly appreciated.

  Hello

  Thanks for posting in the HP Support forum. Welcome!

  According to the model of the computer, it can not be called exactly the HP system recovery but if your computer is originally shipped with Windows preinstalled 10, recovery partition must be present.

  S ' Please, first manually copy your imporant most of the data on an external partition

  -Follow these instructions here to open the collection from inside Windows

  > > http://www.tenforums.com/tutorials/4130-reset-windows-10-a.html

  > > http://www.tenforums.com/tutorials/4130-reset-windows-10-a.html#option2

  'S called it Reset - Windows Reset with options to RESET the machine as long as the plant (remove all), with an option to "freshen up" Windows and keep personal files.

  Let me know how it goes and if it works for you.

• All-in-one HP Pavilion f394: PC cannot recognize the device wireless

  Cannot pair my RocketFish for PC speaker... all tried, device not recognized... one thing remains to check is if my computer has a switch to turn on the Bluetooth / wireless... I can't find anything that looks like a switch, so I think that the problem lies elsewhere!

  I also have a printer connected wireless to PC, so I don't understand why I can't pair the speaker to PC... what else I'm not right?

  PC is only a foot of speaker

  speaker works fine when connected with cable

  My network card is a Qualcomm-Atheros AR 9485 802.11b/g/n WiFi Adapter

  I also have a keyboard and wireless mouse with... PC them found immediately!

  Hello:

  The Qualcomm Atheros AR 9485 802.11b/g/n WiFi to adjust your PC's is not a combination wifi/bluetooth network adapter.

  Your PC has not built in bluetooth network.

  The product also confirm this.   If your PC came with built-in bluetooth, this feature would have been placed on the networking features section.

  http://support.HP.com/us-en/product/HP-Pavilion-TouchSmart-20-F300-all-in-one-desktop-PC-series/5395621/model/5400377/document/c03997171/

  The best thing to do would be to buy an external usb bluetooth adapter.

• Pavilion all-in-one 23: Add the second monitor to HP Pavilion CTO all-in-One-23-p110z

  As it is configured, the factory is the "HP Pavilion all-in-one-23-p110z CTO" capable of supporting a second monitor?  I see NO obvious "video inputs" ports.

  Thank you!

  Hi @beckinista,

  Thank you for being an active member of the HP's Support Forums.   I understand that you would like to know if you can connect a second computer monitor 23-p110z all-in-One CTO Pavilion.

  The specifications of the motherboard of your computer show that there not a secondary display port. I have included HP Pavilion 23 - p110z all-in-one CTO Office product specifications and configurable Options and HP and Compaq Desktop PCs - specifications of the motherboard, Boa for your reference.

  I hope the above helps.

• HP Pavilion 23 touch screen all in one

  After I upgraded to Windows mytouchscreen does not work, when I look for the stylus and touch it says that I don't have, I tried to download

  Hello new @YOLIE80S,

  At this point, I would say we have all the drivers for your computer on Windows 8.1. I would like to have you go to the drivers page from PC Desktop HP Pavilion TouchSmart 23 - f217c all-in-one and start with the Chipset drivers. Once they are installed you should re - install ALL drivers for your computer.

  If the above does not work, we will have to back up, recover your computer to factory settings, run ALL the HP and Windows updates and try again Windows 8.1 update. To save your personal information and ensure it is not lost, I would like you to look at and follow the steps in the HP Support document: backup of files (Windows 8), who will be your personal files are up to date.
  
  CAVEAT! If you want to keep the e-mails or bookmarks/favorites that you want to save them as I do not think they are saved in the backup HP process.
  
  Then, I would like to see again you and follow the steps in the HP Support document: performing a recovery of HP (Windows 8) system, which will allow you through to get your computer back to factory settings.
  
  IMPORTANT - your staff of files such as libraries, personalization settings, user accounts and desktop themes are permanently deleted. The settings on the computer are returned for values by default (as it was when it came from the factory). All applications and software installed on the computer when it came from the factory are relocated, and their settings are reset to the default values. In addition, software, applications, programs, and everything you have installed or saved on the computer are deleted permanently.
  
  Once you have recovered your computer, don't forget to run ALL the updates from HP and then run ALL Windows 8 updates. Finally, run the 8.1 Windows Update, and then install all the drivers on page all-in-one HP Pavilion TouchSmart 23 - f217c drivers PC Desktop that I linked at the beginning of this post
  
  If ultimately it does not work the Pen look and Touch of your computer is perhaps not currently compatible with Windows 8.1 and you may have to wait to see if new drivers are validated. I want to thank you for display on the HP Forums. Have a great day!

• Maximum RAM to HP Pavilion all-in-One MS228sc

  Given that my HP Pavilion all-in-One MS228sc is more slow - even after the release of space on the hard drive that I do research on the possibility of an upgrade of RAM.

  The ins Pavilion "born" with 2 GB of RAM in the slots and 2 GB virtual RAM.

  My question if I can substitute one or both blocks with block of 2 GB RAM. In this way, I'll have 3 or 4 physical RAM instead of 2.

  I guess that will increase the performance of many things

  Hello

  The machine came with 4 GB of RAM, max as shown:

  Memory

  Attributes of the element

  Memory installed	4 GB
  Maximum allowed	4 GB (2 x 2 GB) (64-bit operating system) 4 GB * (2 x 2 GB) (32-bit operating system) * Actual available memory may be less
  Speed support	PC2-6400 MB/s
  Type	200 pin DDR2 SO-DIMM