An unspecified problem was reported. Please check your printer.

Similar Questions

• Your iCloud was suspended, please check your account:

  I received this as a text message on my cell phone:

  Your iCloud was suspended, please check your account:

  http://appleid.Apple.NET.cgi-key.confirm.EU.Web.cmd.myapple.webscmd.Apple.User6. id02.net

  I have connected my iCloud.com iCloud account and everything seems fine.

  I was wondering if this was seen nowhere else in nature (there are no results on Google).

  Thank you

  It seems suspicious, first of all I would expect to be HTTPS and appleid.apple.com not .net.

  I would say that it is a phishing scam!

  If your account has been suspended it would be an e-mail message to your e-mail address associated with your apple ID.

  If you're on an iPhone, report the message as spam and Apple will receive.

• could not find a server reports and analysis hyperion running on localhost port 6800. Please check your connection string server and verify that the server is

  Hi all

  We have properly installed and configured Hyperion Reporting and analysis 11.1.2.4 in windows 2012 server however when I try to logint to the workspace, I get an error like "start-up of the specified document does not exist in the repository." "Select a new start under the General Preferences tab document" monitoring of "could not find a server reports and analysis hyperion running on localhost at port 6800. Please check your connection string server and verify that the server is up '.

  
  

  
  

  

  
  

  

  HyS9RaFramework_epmsystem2-syserr:

  GsmNotFound

  com.brio.one.services.globalservicemanager.GSMException: GsmNotFound

  at com.brio.one.services.globalservicemanager.GSMFactory.getGSM (unknown Source)

  to com.brio.one.client.ClientFactory. < init >(Unknown Source)

  to com.brio.one.client.ClientFactory. < init >(Unknown Source)

  to com.brio.one.client.ClientFactory$ ClientFactoryInitializer.connect (unknown Source)

  at com.brio.one.client.ClientFactory.getClientFactoryConnect (unknown Source)

  at com.brio.one.client.ClientFactory.getDefaultGSM (unknown Source)

  at com.brio.one.web.properties.ApplicationProperties.getDefaultGSM (unknown Source)

  at com.brio.one.web.properties.ApplicationProperties.getDefaultGSMContext (unknown Source)

  at com.sqribe.WS.WSBaseServlet.setDefaultGSMContext (unknown Source)

  at com.sqribe.WS.WSBaseServlet.initLogging (unknown Source)

  at com.sqribe.WS.WSBaseServlet.loadConfiguration (unknown Source)

  at com.sqribe.WS.WSBaseServlet.init (unknown Source)

  to weblogic.servlet.internal.StubSecurityHelper$ ServletInitAction.run (StubSecurityHelper.java:283)

  at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)

  at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)

  at weblogic.servlet.internal.StubSecurityHelper.createServlet(StubSecurityHelper.java:64)

  at weblogic.servlet.internal.StubLifecycleHelper.createOneInstance(StubLifecycleHelper.java:58)

  to weblogic.servlet.internal.StubLifecycleHelper. < init > (StubLifecycleHelper.java:48)

  at weblogic.servlet.internal.ServletStubImpl.prepareServlet(ServletStubImpl.java:539)

  at weblogic.servlet.internal.WebAppServletContext.preloadServlet(WebAppServletContext.java:1981)

  at weblogic.servlet.internal.WebAppServletContext.loadServletsOnStartup(WebAppServletContext.java:1955)

  at weblogic.servlet.internal.WebAppServletContext.preloadResources(WebAppServletContext.java:1874)

  at weblogic.servlet.internal.WebAppServletContext.start(WebAppServletContext.java:3155)

  at weblogic.servlet.internal.WebAppModule.startContexts(WebAppModule.java:1518)

  at weblogic.servlet.internal.WebAppModule.start(WebAppModule.java:487)

  to weblogic.application.internal.flow.ModuleStateDriver$ 3.next(ModuleStateDriver.java:427)

  at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:52)

  at weblogic.application.internal.flow.ModuleStateDriver.start(ModuleStateDriver.java:119)

  at weblogic.application.internal.flow.ScopedModuleDriver.start(ScopedModuleDriver.java:201)

  at weblogic.application.internal.flow.ModuleListenerInvoker.start(ModuleListenerInvoker.java:249)

  to weblogic.application.internal.flow.ModuleStateDriver$ 3.next(ModuleStateDriver.java:427)

  at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:52)

  at weblogic.application.internal.flow.ModuleStateDriver.start(ModuleStateDriver.java:119)

  at weblogic.application.internal.flow.StartModulesFlow.activate(StartModulesFlow.java:28)

  to weblogic.application.internal.BaseDeployment$ 2.next(BaseDeployment.java:672)

  at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:52)

  at weblogic.application.internal.BaseDeployment.activate(BaseDeployment.java:212)

  at weblogic.application.internal.EarDeployment.activate(EarDeployment.java:59)

  at weblogic.application.internal.DeploymentStateChecker.activate(DeploymentStateChecker.java:161)

  at weblogic.deploy.internal.targetserver.AppContainerInvoker.activate(AppContainerInvoker.java:79)

  at weblogic.deploy.internal.targetserver.BasicDeployment.activate(BasicDeployment.java:184)

  at weblogic.deploy.internal.targetserver.BasicDeployment.activateFromServerLifecycle(BasicDeployment.java:361)

  to weblogic.management.deploy.internal.DeploymentAdapter$ 1.doActivate(DeploymentAdapter.java:52)

  at weblogic.management.deploy.internal.DeploymentAdapter.activate(DeploymentAdapter.java:200)

  to weblogic.management.deploy.internal.AppTransition$ 2.transitionApp(AppTransition.java:31)

  at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:261)

  at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:246)

  at weblogic.management.deploy.internal.ConfiguredDeployments.activate(ConfiguredDeployments.java:170)

  at weblogic.management.deploy.internal.ConfiguredDeployments.deploy(ConfiguredDeployments.java:124)

  at weblogic.management.deploy.internal.DeploymentServerService.resume(DeploymentServerService.java:181)

  at weblogic.management.deploy.internal.DeploymentServerService.start(DeploymentServerService.java:97)

  at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)

  at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)

  at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)

  In the workspace, it shows that the Service is pending.

  

  EMP Diagnostic Report:

  

  Can help kindly out how should I solve this problem.

  I restarted the services and rebooted the Machine but still getting the same error.

  Kind regards

  VJ

  
  

  Hello

  I've reconfigured the Reporting, analysis, and everything by, I chose "Drop table" and the issue was resolved.

  Kind regards

  VJ

• your user profile was not loaded correctly! you have been logged on with a temporary profile. Changes to this profile will be lost when you log out. Please, check your log of events for more information or contact your administrator

  Desperately need help.  I'm supposed to use my computer to type a HUGE Affidavit today and its buggered! Oh no.! Get started with my kids have been playing on my computer and install different games.  So I thought that I do the big thing non-technical MOM and start cleaning up the programs!  Well I accidently deleted NIVIDA and probably something else (I think) and totally messed up my computer!  I have re-uploaded NIVIDA and now my computer "looks like" back to normal, but it throws this error message
  
  "your user profile was not loaded correctly! you have been logged on with a temporary profile. Changes to this profile will be lost when you log out. Please, check your log of events for more information or contact your administrator"

  and now I can't save anything or find my pictures that I'm desperate for! Can someone please give me a helping hand.  Not technically minded, to take me on as a challenge!  Thanks bunch :) Sarah

  Desperately need help.  I'm supposed to use my computer to type a HUGE Affidavit today and its buggered! Oh no.! Get started with my kids have been playing on my computer and install different games.  So I thought that I do the big thing non-technical MOM and start cleaning up the programs!  Well I accidently deleted NIVIDA and probably something else (I think) and totally messed up my computer!  I have re-uploaded NIVIDA and now my computer "looks like" back to normal, but it throws this error message
  
  "your user profile was not loaded correctly! you have been logged on with a temporary profile. Changes to this profile will be lost when you log out. Please, check your log of events for more information or contact your administrator"

  and now I can't save anything or find my pictures that I'm desperate for! Can someone please give me a helping hand.  Not technically minded, to take me on as a challenge!  Thanks bunch :) Sarah

  Here is the tutorial to solve this problem. It is very involving. Please read the step by step.
  http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

  t-4-2

• Impossible to reach on the Adobe servers. Please check your firewall settings and try again in a few minutes

  I'm launching the CC Office tab in the menu at the top of my macbook pro bar. The "CC" icon is grayed out now and the message I get when you click on ' impossible to get on the Adobe servers. Please check your firewall settings and try again in a few minutes. I do not have a firewall on my computer and until yesterday it was working fine. I used the CC yesterday to work on a different network, but now I am unable to access it from home.

  I tried things that seem obvious to me as uninstall then reinstall the software of Office CC and I turned my mac and turn it on again a few times but nothing helped. I have also tried to follow the other forum posts asking for similar solutions but don't really understand what they are all talk. If anyone can help it would be much appreciated.

  Thank you, Jamie

  A chat session where an agent can remotely look inside your computer can help

  Cloud creative support chat (all creative cloud customer service problems)

  http://helpx.Adobe.com/x-productkb/global/service-CCM.html

• Cannot open COM1. Please check your port settings, XP SP3

  Hello
  I have some XP SP3 workstations that are used in the factory.  The shell of charge is attached to COM1.  When I test the appliance to make sure that all devices work, the shell load test will not open COM1.  When I use HyperTerminal to test COM1, I get the message "cannot open COM1. Please check your port settings. "I checked the BIOS of a workstation and compare it to the non-working station.  Corresponding to all of the information correctly.  When I check property COM1 resources, the station problem looks identical to the right station and no conflicts.  IRQ 04 corresponds to the current setting.  To get the workstation resurfaced to open COM1, I open COM1 properties, resource tab, uncheck and then re-check "use automatic settings" with your status to uncheck.  After having double checked the "use automatic settings", I click OK.  I then go back to see what the parameters are.  He changed his IRQ 07.  This change works until the computer has been restarted , and then the following steps must be applied again.  Also, if I perform these same steps on a workstation, I get the same results with the change IRQ.  I don't have the problem with com except COM1 ports.  We use the software in a box.  Change to use another com port is not an option.

  Thank you
  MANISH

  Hello

  Note that your computer is under domain, you must contact the TechNet forum, where we are the support technicians who are well equipped with knowledge on the issues of domain, do please visit the link provided below.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

• Cannot open COM1. Please check your port settings

  I have some XP SP2 workstations that are used in the factory.  I use Clonezilla to reimage the workstations (Yes, we have valid licenses for all units) where you have to replace a hard drive or have warranty work that requires a new installation.  We have put arrangements in place on the specified comm ports.  The printer is connected to COM1.  When I test the appliance to make sure that all devices work, the test of the printer will not open COM1.  When I use Hyperterminal to test COM1, I get the message "cannot open COM1. Please check your port settings. "I checked the BIOS of a workstation and compare it to the non-working station.  Corresponding to all of the information correctly.  When I check property COM1 resources, the station problem looks identical to the right station and no conflicts.  IRQ 04 corresponds to the current setting.  To get the desktop put open COM1, I open COM1 properties, resource tab, uncheck and then re - check the box "Use automatic settings" without applying the Statute to uncheck.  After having double checked the "use automatic settings", I click OK.  I then go back to see what the parameters are.  He changed his IRQ 07.  This modification works until the computer has been restarted so the following steps must be applied again.  Also, if I perform these same steps on a workstation, I get the same results with the change IRQ.  I don't have the problem with comm except COM1 ports.  We use the software in a box.  Change to use a different comm port is not an option.

  It seems that the cloning process is causing the problem.  Clonezilla is fast and reliable with the exception of what seems to be a problem of comm port.  I'm looking for someone who can tell me what settings can I change to make COM1 to work without having to go through additional steps after the workstation is restarted.

  Thank you
  Rick

  Hello

  The question you have posted is adapted in the TechNet forums. Post your questions here for a better response.

  Here is the link: http://social.technet.microsoft.com/Forums/en-us/category/windowsxpitpro

• "The Dell Dock language file, which is necessary for its operation, has failed to load. Please check your Dell Dock installation"

  Original title: Dell Dock

  Get a message saying: 'the Dell Dock language file, which is necessary for its operation, has failed to load. Please check your Dell Dock installation

  Try this for the restoration of the system to Vista before the problem:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://www.DellDock.com/

  Above is the link for redownload for him, if necessary.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_technical_support

  Contact the Dell Support link re problems with their software above.

  See you soon.

  Mick Murphy - Microsoft partner

• When I try to send an email to MYOB I get error message saying: "an email session could not be started. Please check your MAPI installation '.

  Error message: a message session could not be started. Please check your MAPI installation - sending email from MYOB

  When I try to send an email to MYOB I get error message saying: "an email session could not be started. Please check your MAPI installation '.

  How can I solve this problem?

  Hi all

  I have a workaround which is a little less boring that the patch "restart the PC": If you get the error where MYOB crashes when you try to send an e-mail, open Task Manager (ctrl-alt-del or right click on the start bar), then go to the "Processes" tab and close all instances of wlmail.exe using the button "complete the process".

  It seems that this error occurs if you have Windows Live Mail opened when you try and send emails of MYOB. If you then close WLMail after that get the error the process seems to never close, so you have to close it manually. If you send all your emails with closed WLMail MYOB it seems to be OK.

  See you soon

• The upgrade of Windows 8 "we can connect you right now, please check your internet connection and try again.

  I just downloaded the upgrade of Windows 8 with the 14:99 option $ discount and after following the steps, he comes to the download section and said "we can connect you right now, please check your internet connection and try again" I tried several times and my internet connection is fine, why am I seeing this?

  Thank you

  PS I am in Australia and Runninng Windows 7 Home Premium 32 bit

  Hey Binka,.

  Your specific error message (failure of the API online store [error: 0x803d0013.]) requires agents that specialize in ESD. 

  The ESD team contacts are listed here.

  There was also another resolution for this source of error in this thread.

  
  

  Windows 8 pro update - we cannot connect

  
  

  He said simply that the original poster had a PC to update and maintain their system and verify that the date is correct are their resolution.

  For all other users who came across this thread, take into account advice from cyberjayar in his post on 31 October. Make sure that your Antivirus programs and firewall is completely turned off during installation. Thanks for posting, happy assignments!

  
  

  -Robert

• We are unable to connect at this time. Please check your internet connection and try again.

  I recently bought a SSD and needed an iso to install Windows with.

  I tried to run the window installer 8 to create the ISO, but every time that I run it and enter my product key, it says:
  We cannot provide at this time
  Please check your internet connection and try again.
  I tried restarting the computer, delete the temporary files, as an admin, creating a new user account, setting my DNS servers, restart my router and my dns to hot flashes.
  I did not have this problem a few days ago, but he had another problem involving incorrect data when you try to run the installer.

  Try to rename or delete the Web installation folder and try again.

  C:\Users\\AppData\Local\Microsoft\Web install

  See also:

  http://techingiteasy.WordPress.com/2013/02/14/how-to-obtain-64-bit-Installer-and-create-install-media-for-Windows-8/

• Impossible to get on the adobe servers, please check your firewall settings and try again in a few minutes

  Adobe Creative cloud continues to print this message and allows me to install in apps "Impossible to reach on the adobe servers, please check your firewall settings and try again in a few minutes" pls help

  Please read https://forums.adobe.com/thread/1499014

  -try some steps such as changing browsers and disable your firewall

  -also clear the cache of your browser if you start with a fresh browser

  -check the file hosts for blocked entries https://forums.adobe.com/thread/1912777

  http://myleniumerrors.com/installation-and-licensing-problems/creative-cloud-error-codes-w ip.

  https://helpx.Adobe.com/creative-cloud/KB/creative-cloud-desktop-application-failed.html

  http://helpx.Adobe.com/creative-cloud/KB/failed-install-creative-cloud-desktop.html

• How to remove the message "Please check your billing information.

  "Please check your billing information" is the title of a message that I get from Adobe, everytime I open my creative cloud Lightroom. The message asking me to update my billing information. I did so, following the suggested steps and I keep getting this message that account the days until I no longer able to access creative cloud. I went to an online chat with the customer support and was informed by the operator that he had updated my account information. It was three days ago and I keep getting the message that my account now has 24 more days to stay active. What can I do now?

  Hello

  You will need to contact support by calling/chat for this request.

  Contact the customer service

  * Be sure to stay connected with your Adobe ID before accessing the link above *.

  Kind regards

  Sheena

• Hi, I tried to download the trial version free photoshops and after I sign in I get this pop up message saying ' unable to reach adobe servers, please check your firewall settings ", I checked the and there is nothing wrong with the firewall, is

  Hi, I tried to download the trial version free photoshops and after I sign in I get this pop up message saying ' unable to reach adobe servers please check your firewall settings ", I checked them and there is nothing wrong with the firewall, is there a problem with the adobe servers? can someone help me?

  Please try the steps mentioned in: https://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

• Failed to load, please check your javascript page errors

  Hello

  After a crash of edge Animate CC 2015 I tried to restart my work, but then I got the following message: echec failure loading, please check your page javascript errors.

  I have seen this problem before the Board of Directors. I looked in the file to see the problem, but my knowledge is not good enough to solve. Can someone help me?

  with sincere friendships.

  Mark

  PS... in the link below, you will find my files.

  http://www.markbroeze.nl/markbroeze_2.zip

  Thank you! You saved me a lot of work. I deleted the double fonts/fonts from the js file and open the file again!