AnyConnect IkeV2 backup server with test

Similar Questions

• VCB to backup server with HP's Eva and Dell AX4 storage systems

  I have two storage systems connected to a backup server. It is installed on Windows 2003 Server x 64 PowerPath5.2. Windows see each storage only once, so I think that multiple paths to the storage works correctly. Whenever I try to start to browse (or start the backup operation) a VM on HP Eva everythink is ok, but for the VM on AX4 I recive error message:

  Error: Cannot open the disk blklst

  :/ / snapshot-2627 [VRAID5_1, 43TB_datastoreDell3] PLBOLFS01/PLBOLFS01.vmdk@plbolvc:

  443? xxxx/xxxx. Could not open the file on disk: error: Disk library failed (can't access

  a SAN/iSCSI LUN support this virtual disk. (Tip: If you use vcbMounter y)

  or may use the '-m ndb' option to switch to disk based network access if it

  you want.) If you were trying to access at the file level, stop the vmount served

  this by typing "net stop vmount2" in a command prompt to force vmount to re-scan f

  or SAN LUNS and try the command again.). Cannot open ' blklst://snapshot-2627 [VRA

  [ID5_1, 43TB_datastoreDell3] PLBOLFS01/PLBOLFS01.vmdk@plbolvc:443'. Conf OMIS

  Figure scsi0:0 of disk.

  An error has occurred, cleaning

  ...

  D:\mnt\PLBOLFS01 deleted directory

  PrepareForBackup() failed to prepare PLBOLFS01 for backup, returned the error 1

  The external command failed. See the above error.

  Exit code: 1

  What can I do with it?

  VCB Version 1.5

  Next step would be to check a second time your zoning and lun masking. There could be a conflict with the various mpio drivers between eva and the clariion. I would try to remove all mpio drivers too.

  Dave

  ************************

  If the automobile had followed the same development cycle as the computer, a Rolls-Royce today cost $100, get 1 million miles per gallon, and explode once a year, killing all the world inside.

  Robert X. Cringely, InfoWorld magazine

• With the support of IKEv2 VPN server configuration

  I'm putting my pc W7 as a VPN server with the support of IKEv2, but it escapes me, although I am not a novice.

  I read a lot of forums "directions for use", but no address really details.

  (1) for IKEv2, I need to install a certificate... I could not find a step by step guide.

  Everyone for help...?

  (2) how to set up the VPN server on my local LAN for testing to exclude router firewall etc... and connect my 920 lumia.

  Everyone for help...?

  Hello

  My apologies for the delay in response.

  For that matter on the VPN with IKEv2 Server Setup, you will need to post your request here on the TechNet forums.

• Backup server AnyConnect when Session limit reach

  Hello

  I did the usual search engine and forum crawl looking for the answer, but can't find anything definitive.

  Is it possible for AnyConnect use the backup server defined in the connection profile when the session limit is reached on a SAA?  Basically if I hit the limit of 250 on my ASA 5510 in zone A, it will try the backup server that ASA is defined in the connection profile which is in region B?

  What I've read, the backup server comes into play when the AnyConnect client cannot connect, but in this scenario, it will connect but get an error message.

  Any input appreciated.

  See you soon,.

  Andrew

  Unfortunately, I think that the answer is no unless she changed in recent versions.  I asked this of Cisco for more than a year.  We have the same problem... when anyconnect hits a bridge but cannot connect because of all sorts of reasons, no IP address remains in the IP local pool, no licenses, failure DAP, etc., he never tries gateways following in the list.  It is ONLY when the door is completely unavailable will continue to backup from the list.  I hope more people chime for Cisco can finally fix this.

• Cloning by rman on a different server with the directory structure different and different DBNAME in EBS 11i using quick Clone

  Hello

  We want only DB (not apps) cloning through PROD rman, step TEST EBS 11i using quick Clone without taking downtime of PROD (i.e. No. BKP COLD).

  Source and target are on different servers, different file structure and the different database name.

  Kindly let me know the detailed procedure?

  Kind regards

  RR

  
  

  You can use this simple method that I am.
  

  
  

  Take backup of production with rman:

  {

  overlap archivelog all;

  backup format compressed backupset database tag PROD_FULLBKP ' / u10/PROD1_L0_BKUP_20131125/PROD_DB_set%s_piece%p_%T_%U' filesperset 15;

  SQL 'alter database backup controlfile to trace. "

  SQL 'alter system switch logfile;

  SQL 'alter system switch logfile;

  SQL 'alter system switch logfile;

  overlap archivelog all;

  backup as compressed backupset archivelog all delete input PROD_ARCHBKP format tag ' / u10//PROD1_L0_BKUP_20131125/ARCH_PROD_set%s_piece%p_%T_%U' filesperset 20;

  backup format ' / u10/PROD1_L0_BKUP_20131125/PROD_ctl_%T_%U' current controlfile;

  }

  
  

  Move the backup on the test server:

  SCP /ftp

  Modify the pfile to the test server:

  Parameters such as:

  db_name

  control_files

  modify the pfile to match the location of the test server

  Add this parameter

  db_file_name_convert = ' / PROD_datafile_location/datafile ', ' / test_datafile_location / data ', ' / PROD_datafile_location/tempfile ', ' / test_datafile_location / data.

  log_file_name_convert = ' / PROD_redofile_location/ONLINELOG ', ' / test_redofile_location / data ".

  Start the DB:

  Start the db in nomount:

  startup nomount.

  Connecting to rman and start to restore:

  Auxiliary RMAN.

  RMAN > run

  {

  allocate auxiliary channel a1 device type disk;

  allocate auxiliary channels a2 device type disk;

  allocate auxiliary channel a3 device type disk;

  allocate auxiliary channel a4 device type disk;

  data duplicated in the PREPRODUCTION backup location ' / u10/PREPRODUCTION/oraR12/clone_backup/PROD1_L0_BKUP_20131125 ";

  }

  OR

  If you specify time/perform a recovery of time based, like below:

  RMAN > run

  {

  allocate auxiliary channel a1 device type disk;

  allocate auxiliary channels a2 device type disk;

  allocate auxiliary channel a3 device type disk;

  allocate auxiliary channel a4 device type disk;

  data duplicated in PREPRODUCTION backup location 'LOCATION_OF_BACKUP', until ' TO_DATE (7 July 2012 09:45 ',' DD/MM/YYYY HH24:MI:SS') ";

  }

  Concerning

  Karim

• Backup VM with VBLOCK

  I'm new to vBlock but have a decent understanding of vSphere and pretty much thru ver4.1 (some in ver 5).  Here's my question:

  I'm with a company that uses vBlock and ESXi4 stand-alone servers.  No vCenter.   Inrteresting Setup.    They are not instant, and they do not have the VM backups.

  Now, I'm still green behind the ears to this company, so I don't think I can say much of their virtual infrastructure and virtual policies, but whenever they need to make changes to their system (even if they are virtual machines), they either do or build a new server and test it on the new server.   In regards to the side of the virtual machine, they told me that they are not instant is because their SAN (Fibre Channel of EMC) vBlock can VM backups.  That's why even serves as to why they have no VM used cover backup/restore applications.   Fortunately, they have never had a need to post this because they have never had to restore a virtual machine.

  I am skeptical.   From what I've read, vBlock and SAN interface device provides true VM backups.   If I'm not mistaken VBlock simply integrates 3 (vSphere, Cisco and EMC SAN routing).   I don't know that the SAN has the standard ability to backup files (IE.  The virtual computer files) but to be able to completely restore a computer virtual... I don't think so.  And, although it is possible to recreate a virtual machine files... it will take time to do so and if the configuration remains intact or not is questionable, in my opinion.   In any case, I wanted to see if someone knew more VBLOCK and could you tell me if what I said is true.    If this isn't the case, I'll have to chime so that they can take the appropriate decisions.

  A Vblock (Yes, that's how VCE spells it) is sold with Enterprise more than license for the hosts, they are required to be able to include Nexus 1000v and PowerPath VE, with vCenter Standard edition (which allows unlimited guests).

  By the reference guide (page 9) architecture - https://community.emc.com/servlet/JiveServlet/previewBody/5665-102-2-20157/h6935-vblock-infra-packages-ref-arc.pdf

• Unavailable backup server

  I'm restarting this topic.  I followed the direction to turn it off, wait, turn on and restart my Palm Pre Plus to launch the automatic backup, but were unsuccessful.  I keep getting the message "backup server unavailable."  Also, I have no list of previous backups, which leads me to believe that my data has never been backed up.

  I have a valid Palm profile because I can log into it, but whenever I try a manual backup, I get an error message 'server not available backup '.

  What is the step beyond to disable the backup, wait, restart, start, manual backup?

  Thanks in advance.

  I was going to just say that I see that you have done a backup today and check back with you to see if you still experience the problem.
  
  I will continue to investigate other issues of backup users.

• Windows backup fails with 0 x 80080005

  You try to start Windows backup fails with the following error:

  The backup application could not start due to an internal error:

  Server execution failed (0 x 80080005).

  Please help, thanks.

  0 x 80070005 backup and Restore Error

  Message: "restoration incomplete. Your computer cannot be restored... »
  (when I run the Windows system with an installed Norton 2010 product restore)

  http://www.Symantec.com/Norton/support/kb/web_view.jsp?wv_type=public_web&docURL=20091030142819EN&LN=en_US

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• Anyconnect Ikev2 uses aggressive Mode

  Hello world

  I'm trying to fix the IKE Aggressive mode with vulnerabilities PSK on our Cisco ASA that runs old IPsec and Ikev2 Anyconnect VPN.

  When I run the command

  Crypto isakmp HS her

  User using IPSEC VPN

  IKEv1 SAs:

  HIS active: 25
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 25

  1 peer IKE: 63.226.x.x
  Type: user role: answering machine
  Generate a new key: no State: AM_ACTIVE

  Then, he tells me that this VPN client is using aggressive mode right?

  User using IKEV2 anyconnect

  Crypto isakmp HS her

  17 peer IKE: 192.206.x.x
  Type: user role: answering machine
  Generate a new key: no State: AM_ACTIVE

  IKEv2 SAs:

  Session-id: 361, status: ACTIVE UP, IKE County: 1, number of CHILDREN: 1

  Tunnel-id Local remote status role
  x.x.x.x/4500 1696279645 192.206..x.x/33328 answering MACHINE READY
  BA: AES - CBC, keysize: 256, Hash: SHA96, Grp:5 DH, Auth sign: RSA, Auth check: EAP
  Duration of life/active: 86400/24756 sec
  His child: local selector 0.0.0.0/0 - 255.255.255.255/65535
  selector of distance 172.16..x.x.144/0 - 172.16.x.x/65535
  SPI ESP/output: 0xa315b767/0xbec2f7cc

  Need to know anyconnect ikev2 does not share any key of share pre then why the number of line 17 shows AM (aggressive mode)?

  The ikev2 Protocol has nothing to do with the aggressive mode or main at all.

  If you do a 'sh crypto isa"it will show you the the ikev1 and his ikev2.

  If you still see a flow in the table, maybe it's a stuck session.

  To disable the aggressive mode, enter the following command:

  Crypto ikev1 am - disable

  For example:

  HostName (config) # crypto ikev1 am - disable

• Using IKEv2 from Microsoft with Cisco ASA

  Hello

  I just want to confirm something, if I can put this issue to rest.

  We have a Cisco ASA 5505 running OS 8.4

  For remote access, we have the configuration of SSL VPN to include IPSec (IKEv2).

  With the help of our AnyConnect client works.  No problem.

  The issue is on my Windows 7 computer when I place a remote access profile I choose IKEv2 (PPTP or L2TP/IPSec).  However, this does not work.

  It error to say that he "cannot find a matching policy.  I'm assuming what he mean't he couldn't find any political IKE.  I have added other policies of IKE, which has find a match, but ASA connects the barks by saying "IKE neogoiation fails in search of a certificate or a preshared key".

  There is no option for inputing a pre-shared for IKEv2 on Windows 7 with its profile.

  Therefore, I think that on the ASA 5505 IKEv2 is only used for remote access with the AnyConnect client (or the client AnyConnect Secure Mobility) and NOT with other clients like Microsoft IKEv2.

  Is this really the case?  Or can I use IKEv2 integrated with Windows 7 to access remotely the ASA 5505 enabled for IKEv2 for remote access (and not as a site-based virtual private network)?  If so how did you get it to work.  It is an empty topic of discussion on the Internet.

  Thank you!

  -rya

  Hi Rya,

  I don't think there are changes to this recently but ASA doesn't work with anyconnect with IKEv2.

  I recently wrote about this in my blog

  https://supportforums.Cisco.com/community/NetPro/security/VPN/blog/2011/02/08/ASA-84-IPSec-VPN--whats-new
  (Point 4)

  Frankly I did not follow developments of this features recently, so I might have missed something.

  Marcin

• Help with the easy VPN server with LDAP

  Hello

  I used to be able to set up our easy VPN server with local authentication.

  But now, I'm trying to use LDAP authentication to match with our policies.

  Can someone help me please to check the config and tell me what is wrong with him?

  My router is a Cisco1941/K9.

  Thank you in advance.

  Ryan

  Current configuration: 5128 bytes
  !
  ! Last configuration change at 13:25:16 UTC Tuesday, August 28, 2012, by admin
  ! NVRAM config update at 05:03:14 UTC Monday, August 27, 2012, by admin
  ! NVRAM config update at 05:03:14 UTC Monday, August 27, 2012, by admin
  version 15.2
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  router host name
  !
  boot-start-marker
  boot-end-marker
  !
  !
  !
  AAA new-model
  !
  !
  AAA group ASIA-LDAP ldap server
  Server server1.domain.net
  !
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authentication login ASIA-LDAP-AUTHENTIC ldap group ASIA-LDAP
  local VPN_Cisco AAA authorization network
  Group ldap AAA authorization network ASIA-LDAP-ASIA-LDAP group authorization
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  !
  No ipv6 cef
  !
  !
  !
  !
  !
  IP domain name domaine.net
  IP cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  Crypto pki token removal timeout default 0
  !
  Crypto pki trustpoint TP-self-signed-765105936
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 765105936
  revocation checking no
  rsakeypair TP-self-signed-765105936
  !
  !
  TP-self-signed-765105936 crypto pki certificate chain
  certificate self-signed 01
  30820229 30820192 A0030201 02020101 300 D 0609 2A 864886 F70D0101 05050030
  2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30
  69666963 37363531 30353933 36301E17 313230 36323630 39323033 0D 6174652D
  355A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031
  532D 5365 6C662D53 69676E65 642D 4365 72746966 69636174 652 3736 35313035
  06092A 86 4886F70D 01010105 39333630 819F300D 00308189 02818100 0003818D
  C1B7E661 4893D83A EFE44B76 92BAA71A 6375 854 C 88 D 4533E51A 49791 551D8EF7
  F82E2432 E65B401D 27FE4896 2105B38A CB1908C1 9AE2FC19 8A9393C3 1 B 618390
  EE6CB1CC 5C8B8811 04FA198E 16F3297B 6B15F974 13EE4897 97270547 31 74270
  4590ACA6 68606596 97C5D4D5 462CACA0 CDDAC35A 17415302 CFD4E329 8E7E542D
  02030100 01A 35330 03551 D 13 51300F06 0101FF04 05300301 01FF301F 0603551D
  23041830 1680142E FF686472 569BCCF1 552B 1200 1 060355 5B660F30 D35060DB
  1D0E0416 04142EFF 9BCCF155 68647256 2B1200D3 5060DB5B 660F300D 06092 HAS 86
  01010505 00038181 00558F64 05207 D 35 AA4BD086 4579ACF6 BCF6A851 4886F70D
  1D0EA15B 75DBFA45 E01FBA5C 6F827C42 1A50DD11 8922F1E5 3384B8D8 8DD6C222
  0187E501 82C1C557 8AD3445C A4450241 75D771CF 3A6428A6 7E1FC7E5 8B418E65
  74D265DD 06251C7D 6EF39CE9 3 D FE03F795 692763 AE865885 CFF660A5 4C1FF603
  3AF09B1E 243EA5ED 7E4C30B9 3A
  quit smoking
  license udi pid CISCO1941/K9 sn xxxxxxxxxxx

  ISM HW-module 0
  !
  !
  !
  secret admin user name of privilege 15 5 $1 rVI4$ WIP5x6at0b1Vot5LbdlGN.
  ryan privilege 0 0 pass1234 password username
  !
  redundancy
  !
  !
  !
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  Configuration group customer isakmp crypto VPN_Group1
  xxxxxxxxxxxx key
  DNS 10.127.8.20
  pool SDM_POOL_1
  ACL 100
  netmask 255.255.255.0
  ISAKMP crypto ciscocp-ike-profile-1 profile
  match of group identity VPN_Group1
  authentication of LDAP-ASIA-AUTHENTIC customer list
  whitelist ISAKMP ASIA-LDAP-authorization of THE
  client configuration address respond
  virtual-model 1
  !
  !
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  !
  Profile of crypto ipsec CiscoCP_Profile1
  game of transformation-ESP-3DES-SHA
  set of isakmp - profile ciscocp-ike-profile-1
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  IP 10.127.15.1 255.255.255.0
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  Shutdown
  !
  interface GigabitEthernet0/0
  IP xxx.xxx.xxx.xxx 255.255.255.224
  automatic duplex
  automatic speed
  !
  interface GigabitEthernet0/1
  IP 10.127.31.26 255.255.255.252
  automatic duplex
  automatic speed
  !
  type of interface virtual-Template1 tunnel
  IP unnumbered Loopback0
  ipv4 ipsec tunnel mode
  Tunnel CiscoCP_Profile1 ipsec protection profile
  !
  local IP SDM_POOL_1 10.127.20.129 pool 10.127.20.254
  IP forward-Protocol ND
  !
  IP http server
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP route 0.0.0.0 0.0.0.0 GigabitEthernet0/0
  IP route 10.0.0.0 255.0.0.0 10.127.31.25
  IP route 10.127.20.128 255.255.255.128 GigabitEthernet0/0
  !
  Note access-list 100 category CCP_ACL = 4
  access-list 100 permit ip 10.0.0.0 0.255.255.255 everything
  !
  !
  !
  !
  !
  !
  !
  LDAP attribute-map ASIA-username-map
  user name of card type sAMAccountName
  !
  Server1.domain.NET LDAP server
  IPv4 10.127.8.20
  map attribute username-ASIA-map
  bind authenticates root-dn CN = xxx\, S1234567, OU = Service accounts, OR = Admin, OU = Acc
  DC = domain, DC = net password password1
  base-dn DC = domain, DC = net
  bind authentication-first
  !
  !
  control plan
  !
  !
  !
  Line con 0
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line 67
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line vty 0 4
  transport telnet entry
  !
  Scheduler allocate 20000 1000
  end

  Router #.

  Ryan,

  It seems that you are facing the question where it is indicated in the section:

  Problems with the help of "authentication bind first" with user-defined attribute maps:

  * Then you are likely to see a failure in your authentication attempt. You will see the error message "Invalid credentials, result code = 49.  The newspapers will look something like the journals below: *.

  Which is the same error you see. Go ahead and replace in your attribute map and test again.

  If you remove the command "bind-first authentication' configuration above, everything will work correctly.

  https://supportforums.Cisco.com/docs/doc-17780

  Tarik Admani
  * Please note the useful messages *.

• I'm transferring my entire website from my old Web host at GoDaddy. How to copy all my files (in Dreamweaver) to my Web site from the server, it's on now, on my desk? So I can then connect you to my new server with GoDaddy and transfer all s

  I'm transferring my entire website from my old Web host at GoDaddy. How to copy all my files (in Dreamweaver) to my Web site from the server, it's on now, on my desk? So I can then connect you to my new server with GoDaddy and transfer all of the site?

  If you don't have local copies of your site on your computer...

  1 create a new Site definition using your old FTP GS-01 information: definition of a new site. Learn Dreamweaver CS5 & CS5.5 | Adobe TV

  2. Once you have the defined site and can connect, click on the Get (down arrow) command in the files Panel

  3 when you are prompted to hit "get the entire Site? Yes

  4. After downloading the entire site, navigate to the Site > Manage Sites > click the site > Edit > servers > click on the remote server > Edit to enter your new GoDaddy FTP Info

  5. after the test connection to check, you can connect, click the command Put (up arrow) in the files Panel

  If you have a site already defined for your old Web host, go to #4 above.

• Cheap construction and Simple Home ESXi Server to test

  I think building a desktop computer (you can call it home server) for VMware vSphere Hypervisor to test at home for educational purposes.  I am currently using a > 6 yr old Dell laptop which does not support VMware vSphere hypervisor.  I have no luck in my workplace to have hands on VMware.  Course VCP5 is expensive here in Malaysia, about 3 times salary for a fresh grad. If you have savings of 1/3, should be save to just sign up for the course of 9 months.  Also I would need to take leave of 5 days on the course, they have no weekend class.

  My plan is to set up for lab test (VCP5 test) and possibly configure 4 virtual machines.  What are the best way to build that ESXi server to test?

  Processor - AMD FX-6100

  http://www.Newegg.com/product/product.aspx?item=N82E16819103962

  Motherboard - ASRock 960GM/U3S3 FX [Micro-ATX]

  http://www.Newegg.com/product/product.aspx?item=N82E16813157323

  RAM - 16 GB (2 x 8 GB) 240 - Pin DDR3 SDRAM DDR3 1600 (PC3 12800)

  http://www.Newegg.com/product/product.aspx?item=N82E16820231606

  Adapter - Realtek 8111E (shipped with Mobo)

  HARD drive - WD Green WD10EZRX 1 TB IntelliPower (do not plan for any RAID installation)

  http://www.Newegg.com/product/product.aspx?item=N82E16822236070

  Box - COOLER MASTER Centurion 5

  http://www.Newegg.com/product/product.aspx?item=N82E16811119068

  Power - COOLER MASTER eXtreme Power Plus 500W or COOLER MASTER GX 450W RS450

  I have experince in the building of my own office back in the years of the pentium - pentium 4.  But I certainly have no experience in the construction of a system as complicated as, I am a total newbie to VMware.  I need your need help and tips to avoid buying machines bad for my setup.

  my budget would be RM3000, which is about USD1000. (Now I think I can get USD600 below after opt for AMD on Intel Core i7)

  Thank you

  * Some links that I found

  Hardware configuration

  http://wahlnetwork.com/2012/03/13/building-ESXi-5-whitebox-home-lab-servers/

  http://vdestination.com/2011/01/19/building-a-home-lab-101/

  Configuration (configure lab environment, do not apply to me)

  http://professionalvmware.com/2012/05/vSphere-5-autolab/

  http://www.simple-talk.com/sysadmin/virtualization/VMware-Lab-Setup---a-virtualized-lab-for-testing-HA-and-DRS/

  http://www.VMwarevideos.com/video-my-home-VMware-vSphere-lab

  You don't need a San to install ESXi, but if it's under consideration for the VCP that a SAN would be beneficial, as would a second host ESXi - in this way you will be able to test vMotion, DRS, HA-

• Server with 10 TB LUN attached by physical brutes FC connection works, but second 10TB seems to be limited

  I have an ESX Server with two virtual machines on it, one of the servers is to store medical images. These virtual machines are essentially backup servers to servers that are physical (not virtual).  The main server is a physical server with an attached IBM DS4700 direct and secondary sandbox. I have 20 TB of data spaced so far.  Side virtual server also direct a of DS4700 attached to the area of ESX and he sees the first 10 fine to, as a single disc, and Yes, I know that this seems to go against the norm.  In any case we work for well over a year to date.  I add the second 10TB and I now seem to be limited by the expected 2 TB-512 b per LUN through documentation.  I would like to know why I was able to create the first 10 TB LUN without problem using physical RDM mode, but when I try to add the next physical drive from RDM on the same server (see 9.54 TB LUN very well), using the same method, why windows or should I say VMWare ESX is not being able to see the 10 to complete this time.  I am aware of the supposed limits, but the first works fine, why only now did he not see it.  To clarify the "Add" function of VMWare 9.54 Tb thin LUN during the creation of the new disc, but in Windows, it only recognizes the first 1.5 to (so it seems) I have not actually tried to format the volume in Windows and have yet once removed from the virtual machine.

  Windows 2008 64 bit standard on top of ESX 4 Enterprise Plus connected via direct fiber DS4700 and DS4000 with 10 TB on each table.  The virtual machine has been improved to version 7 machine and I have NOT tried add the second 10TB still with the new VM version. Thought I would ask first.

  Yes, you can map your volume of GPT in any physical Windows but I can't tell if you will experience data corruption or not, as I know that more than 2 TB volumes don't are not supported with current versions of vSphere.

  It is a good article on 2 TB limit, and how taken Windows support that: http://blogs.technet.com/b/askcore/archive/2010/02/18/understanding-the-2-tb-limit-in-windows-storage.aspx

  Tomi

  http://v-reality.info

• Editing a data store on the backup server

  Hello

  I have an ESXi 4.0 production (free version) with 2 virtual machines.

  I have a second server ESXi 4.0 which will be my backup server. This server has a data store single named 'VM-Store.

  Question: Can my production server I mount the datastore (VM-Store) located by backup server?

  Thank you

  Terry

  Welcome to the forums - you can not mount th einternal by another host ESX esx host storage - you'll need some kind of storage device shared as FC SAN, iSCSI SAN or NAS/NFS.

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful