ASA 8.2 (5) upgrade 8.2 (5.26) breaks through VPN?

Similar Questions

• After ASA 7.1 (2) upgrade 8.0 (4) remote VPN is not working properly.

  I just upgraded my ASA from 7 to 8 and now, my remote access VPN working properly. The tunnels connect and I can ping anything, but I can't browse network shares or connect to Exchange.

  No idea as to what I'm missing?

  Thank you

  Dan

  IPSec VPN packets are removed when compression is enabled, when you configure the enable command ip-comp under Group Policy, then large packages that are eligible for compression are deleted in silence by the security apparatus. VPN compression is only useful for very slow Internet connections, so we suggest you disable compression (ip-comp disable). Alternatively, you can move on to build interim 8.0 (4.16) or later. (CSCsu26649)

  Release notes for Cisco 8.0.4.

• ASA 5510 to Sonicwall TZ205 - ASA 9.1.6 upgrade breaks Tunnel VPN

  After reclassification of 8.4.5 to 9.1.6 my tunnel from site to site between an ASA 5510 and a Sonicwall TZ 205 is 'up' and I can ping the external interface of the other but I can't ping LAN to LAN.

  Hey Kevin,

  They should not be a difference on the config VPN between these versions, can you try to run a packet - trace on the SAA or place a screenshot inside while sending traffic.

  Example:

  entry Packet-trace within the icmp < src="" ip=""> 8 0

  Capture the vpn inside the match ip host host interface

  It may be useful

  -Randy-

• site-to-site between 5505 s ASA: a subnet cannot send traffic through VPN

  Hello again! In case you saw my last post, I managed to solve the problem of isakmp with my tunnel from site to site a couple of weeks.

  Everything works fine now, except for one strange thing. First of all, a topology:

  Our main campus is 1 (192.168.32.0/20) of the plant, plant 2 (192.168.16.0/20) and MOS (192.168.0.0/20). The ASA "KSIASA01" is on the main campus.

  On the other side of the tunnel, on a SDSL circuit ~ 400 Kbps, is plant 3 (192.168.48.0/20) and the ASA "KSIASA03."

  Now I can ping addresses in factory 3 very well to our main campus, if I leave the subnets 192.168.11.0/24, 192.168.25.0/24, 192.168.18.0/24 and 192.168.42.0/24. However, several other subnets fails when I ping from the main campus. The. I'm more concerned is 192.168.38.0/24.

  Here's the twist: if I ping from plant 3, I can ping everything in the main campus very well. Also, after I ping the subnet 192.168.38.0/24 of plant 3, I can then ping back from 192.168.38.0/24 to plant 3 without problems. But after an hour or two, we can no more.

  On KSIASA01, if I turn the Packet Tracer, failed pings reach "VPN Lookup" and then fail with "(acl-drop) Flow is refused by the configured rule." "

  My research tells me so far that it can be a NAT problem, but I can't understand it. I will attach sanitized configs for the two ASAs. Thanks in advance for your help and advice.

  Hello, Jefferson.

  NAT seems perfect (at first glance).

  The only problem I've found there's inconsistency in encryption ACL:

  the Plant1-Plant2-MOS object-group network

  network-object MOS 255.255.240.0

  network-object Plant2 255.255.240.0

  network-object Plant1 255.255.240.0

  outside_2_cryptomap list extended access allowed object-group Plant1-Plant2-MOS Plant3 255.255.240.0 ip

  vs.

  the Plant1Plant2MOS object-group network

  network-object MOS 255.255.240.0

  network-object Plant2 255.255.240.0

  object-network Subnet38 255.255.255.0

  object-network Subnet42 255.255.255.0

  access extensive list ip Plant3 outside_1_cryptomap allow 255.255.240.0 object-group Plant1Plant2MOS

• ASA 5510 worm. 8.2 (5) access through VPN without client management?

  Hi all

  I am completely new to networking Cisco and virtual private networks, I'm working on to the ASA 5510 8.2 (5) 46.  Currently, the unit is set up very very little.  Access to the administration are accessible from my home network to 192.168.2.1.  I'm trying to enable management access remotely by VPN.  I created a clientless SSL VPN, which, during the wizard process, access to the specified administration was the/admin adding to the VPN https url.  Add the/admin in the url for VPN is not me the VPN connection, and by using the/admin url from the portal returns a message "not available".  Also, from the portal I can't access the ASDM using inside IP network management, it also returns the message as "unavailable".  Again, I'm new to this, any help would be greatly appreciated.  Here is my config.  and thank you!

  : Saved : ASA Version 8.2(5)46 ! hostname ALP5510 enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted names ! interface Ethernet0/0 nameif outside security-level 0 ip address 99.66.203.148 255.255.255.248 ! interface Ethernet0/1 shutdown no nameif no security-level no ip address ! interface Ethernet0/2 shutdown no nameif no security-level no ip address ! interface Ethernet0/3 nameif inside security-level 100 ip address 192.168.2.1 255.255.255.0 ! interface Management0/0 nameif management security-level 100 ip address 192.168.1.1 255.255.255.0 management-only ! boot system disk0:/asa825-46-k8.bin ftp mode passive dns domain-lookup inside dns server-group DefaultDNS name-server 68.94.156.1 name-server 68.94.157.1 same-security-traffic permit inter-interface pager lines 24 logging asdm informational mtu outside 1500 mtu inside 1500 mtu management 1500 ip local pool vpn 192.168.2.10 no failover icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-714.bin no asdm history enable arp timeout 14400 global (outside) 101 interface nat (inside) 101 0.0.0.0 0.0.0.0 nat (management) 101 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 99.66.203.150 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http server session-timeout 20 http 192.168.1.0 255.255.255.0 management http 192.168.2.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.2.0 255.255.255.0 inside ssh timeout 5 console timeout 0 management-access inside dhcpd address 192.168.2.3-192.168.2.10 inside dhcpd dns 68.94.156.1 68.94.157.1 interface inside dhcpd enable inside ! dhcpd address 192.168.1.3-192.168.1.10 management dhcpd dns 68.94.156.1 68.94.157.1 interface management dhcpd enable management ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside enable inside group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn webvpn   svc ask enable group-policy eng internal group-policy eng attributes vpn-tunnel-protocol webvpn webvpn   url-list value EngineerBookmarks username user1 password mbO2jYs13AXlIAGa encrypted privilege 15 username user1 attributes vpn-group-policy eng webvpn   url-list value EngineerBookmarks tunnel-group test type remote-access tunnel-group test general-attributes address-pool vpn tunnel-group Engineering type remote-access tunnel-group Engineering general-attributes default-group-policy eng ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters   message-length maximum client auto   message-length maximum 512 policy-map global_policy class inspection_default   inspect dns preset_dns_map   inspect ftp   inspect h323 h225   inspect h323 ras   inspect rsh   inspect rtsp   inspect esmtp   inspect sqlnet   inspect skinny    inspect sunrpc   inspect xdmcp   inspect sip    inspect netbios   inspect tftp   inspect ip-options   inspect icmp ! service-policy global_policy global prompt hostname context no call-home reporting anonymous Cryptochecksum:05f3afe3383542c8f62b1873421a7484 : end asdm image disk0:/asdm-714.bin asdm location 99.66.203.150 255.255.255.255 inside no asdm history enable 
  
  
  			 
  I'm TAC if you give me a number I can help you, I think we will extend that if we continue on the support forum
  		   

• Upgrade to 2.3.3 break functions

  my phone updated to 2.3.3 and now parts of my apps don't work

  problem 1:

  using cameraUI the software will direct the user to the camera and take a picture, then use this

  deviceCameraApp.addEventListener (MediaEvent.COMPLETE, imageCaptured);

  to return the image information

  This no longer works.  It's as if the app is completely restarted once the image is taken.

  problem 2:

  This no longer works

  var callURL:String = "this:" + num;

  var targetURL:URLRequest = new URLRequest (callURL);

  navigateToURL (targetURL);

  He will lead the phone dialer to the user, but does not fill the phone number field

  any help guys?

  found the problem

  I had to overlay air 3.0 in flash pro

• ASA with fire 5555 x Installation/Configuration/full features enablment

  Dear,

  I had a lot of confusion about the ASA with the power of fire all the new features, upgrade, changes made me lost.

  Can someone describes the steps to install the ASA with firepower and upgrade its image & package and the license application. (configuration of the box from scratch).

  What is the best practice for the installation of ASA with firepower in a network?

  TAMÁS is our license what are the features will be important for me, if I want to do a total security. And how about internet proxy I think of ending my TMG Web proxy and use this ASA. I want to use the devices to its full occupancy and all the features that I needed to be activated if necessary.

  How to deal with WLC and the wireless network (which is the best practice for ASA with the firepower and WLC

  Yes maybe that's a lot, but I think many inspiring answers will knock at least with redirection to another topic or some brilliant ideas.

  Kind regards

  Christel

  @mishaal-thabet

  There is a Quick Start Guide to ASA with module power of fire services here:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/SFR/firepo...

  In addition, to configure your policies of Management Center of firepower to make the most effective module, I recommend the Cisco Live presentation by 2015: "BRKSEC-2018 migration ASA IPS and CX to firepower." You don't have to worry about the title, it's a good overview for most use cases.

  It can be found here:

  https://www.ciscolive.com/online/connect/sessionDetail.WW?SESSION_ID=836...

  The WLC interact with the ASA directly but the placement of your controller and you use anchor and host controllers can play in your ASA interface design (i.e. comments in an area controllers demilitarized). Other than that, Wireless subnets are just part of the variable "$HOME_NET" located on the module of firepower.

  I hope this helps.

• How can I upgrade images IOS system of routers, switches and firewalls

  Hello

  I am very surprised and fewer still understand how the program license or the Cisco's IOS upgrades are done. I have several routers, switches & ASA who I wan upgrading of IOS, but I can't do it. How ever I can download these images on the internet, but I want to know how can I do this Cisco as I don't trust these IOS is available on the internet.

  According to my study I found that I need to have the number of Cisco Service contract for the devices so that I can download updated the IOS Images for them.

  Someone kindly explain what are the best methods for requirements above.

  Concerning

  @Mohammed

  You are right about a contract of service. Cisco calls this Smartnet support. It includes both supported hardware (i.e. returns for defective equipment), software support (including the right to download and upgrade your software) and technical assistance (through the Cisco TAC). SMARTnet is charged separately for each device covered. Once you have it, your cisco.com username must be associated with your service contract number. This will allow then allows you to download the software of cisco.com. (There are a few cases where you don't have to have a support contract - especially when there is a safety notice (PSIRT) indicating that the Cisco software was flawed it was released at the beginning.)

  Each product (or product family) has a product on cisco.com support page. This page includes release notes, Setup guide, user guides and links to downloads of software for this product. Start by reading the release notes and determine which (if any) update is appropriate for your product. Then, you can download and upgrade the software if necessary.

• The ASA - Client to use SSL and connections options I have?

  We have a large site and have only allowed using IPSEC for all our branch in branch and the user tunnels. We tried SSL years but she limits so we stopped deployment. We must now begin the SSL VPN user and I have a few questions basic ASA.

  I have a unused ASA 5510 for tests that currently holds the 8.3.2 on it, Security code more license, 100 SSL VPN peers and 250 total peers of VPN, VLAN max 100, 2 seconds, active/active contexts, 2 proxies of phone CPU and everything else is disabled. We do not intend on using a SSL connection web anywhere (Anyconnect essentials?) and will not use the entire customer VPN SSL which will be hand loaded on machines or downloaded from the ASA and loaded on the computer if possible. I want to know is what version of the current code can install on my ASA without losing my existing SSL VPN 100 peers license and that the Anyconnect customer would be sustained? I've seen talk about premium Anyconnect but do not know its relationsonship. If I improve the ASA of new releases or versions of code my peer SSL VPN license turns into an Anyconnect Premium license?

  Any help to get started you in the right direction would be appreciated. I know I can spend days trying to understand Cisco licenses and traps and still get burned in the end with the function or the wrong license. Basically, I want to know what I have to install the end-user complete SSL VPN clients and I have to do with the ASA to provide this functionality with current license / feature set there. I also want to know what the end user should be used because it seems that Anyconnect Secure Mobile is the same if I use all its security features. Example - I am not able to check for firewall/malware etc programs but we currently have a policy in place which does not allow browsing the Internet or access when end users have connections VPN tunnel on our site. That restriction will always be kept if this is possible thanks to the SSL VPN connection also.

  Thank you

  Paul

  The SSL VPN client-based license will remain active on your box through Software ASA updates later. AnyConnect Essentials (which you already have) will work with the feature of SSL VPN license.

  You would be upgrading to AnyConnect Premium only if you wanted to add features like clientless SSL VPN (purely based on a browser) or other items such as Advanced Endpoint Assessment (AEA). AnyConnect Premium can coexist with Anyconnect Essentials on the SAA even if you can't mix and match licenses Premium and Essentials.

  Essential distinction or Premium is mainly directed towards the installation of the ASA. The same AnyConnect Secure Mobility client software (version 3.1 is the latest for Windows and OS X and is quite a nice new version) is used in both cases. Functional additional client plug-ins are things such as the AEA and the NAC 802.1 x. Your group policies based on the SAA as no split tunneling, etc. remain in force.

  If you intend to allow clients of mobile devices (iPhone, iPad, and Android (a very limited support for the last BTW)) to access your VPN, you will need to add the mobile on the SAA AnyConnect license and install the client from the respective AppStore. Note that Windows Phone and Blackberry don't are not supported as client AnyConnect.

• VPN access no longer works after upgrade from 10 IOS!  Any input to fix?

  VPN access no longer works after update IOS 10!  With the help of an iPhone 5 or 6, our employees use their hotspot phone to connect to our VPN.  Suddenly, he broke Monday after the upgrade to IOS 10.  We have experienced many versions of IOS, and it has always worked.  Any patch available?

  Hello howlindaug,
  Thank you for using communities of Apple Support.

  If I understand your message that your employees will no longer be able to connect to your virtual private network with their iPhone 5 or 6 after the upgrade to iOS 10. Sierra Mac OS and iOS 10 delete a VPN profile PPTP connections when a user upgrades from their device. If your VPN is a PPTP connection, you'll want to use one of the options listed in the section below:

  Prepare for removal of PPTP VPN before upgrade you to iOS 10 and macOS Sierra
  

  Alternatives for PPTP VPN connections

  Try one of these other VPN protocols for authentication by user that are safer:

  • L2TP/IPSec
  • IKEv2/IPSec
  • Cisco IPSec
  • VPN SSL clients on the App Store, such as those of AirWatch, Aruba, Check Point, Cisco, F5 Networks, MobileIron, NetMotion, Open VPN, Palo Alto Networks, Pulse Secure and SonicWall

  Best regards.

• Upgrade to Windows 10 from 8.1 to Bootcamp

  Hello

  I recently installed windows 8.1 on my macbook pro 15 retina using bootcamp. I have now an iso upgrade windows 10 on a USB and a product key. IM wondering now how the upgrade. Can I do it through the windows partition, or on the side of OS X using bootcamp? Also, if I do it through side windows, making the risk of having the upgrade wipe the OS X partition or will it stay within the windows partition? Mind you, I'm not very tech savvy, please use as many details as possible.

  Thank you

  What year/model is your Mac?

  Please make sure that your Mac is listed in use 10 Windows on your Mac with Boot Camp - Apple Support, otherwise you will encounter problems of pilot.

• Upgrading RAM... what will happen on my cluttered Desktop?

  Re; early 2009 iMac 10.10.5 (2) x 2 GB RAM modules pre upgrade.

  When I go through the procedure of Exchange to my old for additional RAM modules and more new RAM modules, what will happen on my busy office, if anything?

  It is my understanding that links file that you drag on the desktop are stored in RAM.

  When I leave the current RAM modules, all that now appears will be lost, or much less accessible?

  Accessibility is the whole point to have them there.

  Am I worrying unnecessarily, or if I am save these file, image and video links very used somewhere?

  Nothing will happen.  The content of the Finder window is not stored in volatile RAM, but in the database and preference files to make them permanent, subject to your evolution, which is on the desktop at any time.

  

• iPad with Safari after upgrade issues

  I have an iPad model no MD526B/A and since the upgrade I have problems with clicking through websites of salma and Mail.  Any suggestions?

  This is a common problem and there is currently no permanent solution.

  Try turning off JavaScript under settings - Safari - Advanced.

• Want to 24-n075na: upgrade to Windows 10 Pro on Envy 24-n075na All-- One PC in

  I tried to upgrade to Windows Pro 10 on the Envy 24 - n075na all-in-One PC of Windows 10 Home. He can't be upgraded.  It seems to go through the process of upgrading shutsdown and restarts and then displays a message that says: it could not be upgraded.

  Any ideas.

  Thank you

  I thought about it. It was mcaffee blocking the upgrade. Remove and the update worked fine!

• free upgradation of geniune vista home premium to Windows 7 is possible or not.if yes how

  Sir, I bought acer 5738 laptop G 3 months ago with vista Home premium pre-installed.i am in India. I heard that microsoft provides for free upgradation of windows 7 at all its vista users.i am badly in need for upgradation to win 7. Please guide me how detailed and easy for the same.can it be done online. I'm not an IT professional.

  Hello avinash kumar singh,.

  Welcome to the Microsoft Answers Forum!

  There is an upgrade if you acquire a product as packaged at retail of Windows® Vista between June 26, 2009 and January 31, 2010, you are eligible to receive product upgrade Microsoft Windows 7 corresponding to the cost of shipping and handling ($9.99). Count 6 to 8 weeks (depending on the availability of inventory) for delivery following the release of Windows 7 on October 22, 2009.

  Here is a link that will give you information on the upgrade option:
  http://www.Microsoft.com/Windows/buy/offers/upgrade-option.aspx

  Please go through it and check if you have an eligible Windows Vista to take advantage of the upgrade to the cost of shipping.

  Here is a link that will give you information about the terms and conditions:
  https://OM2.one.Microsoft.com/OPA/validation.aspx?storeid=127971aa-ac70-438F-9304-4bd05de66415&LocaleCode=en-us

  I hope this information helps. Please get back to us if you have any other questions on this subject.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know.