ASA disconnects the customer due to the XAUTH failure even if XAUTH disabled

Similar Questions

• L2l VPN between ASA with the IP address public and CISCO2911 behind the ISP router with port forwarding

  Hi all

  My apologies if this is a trivial question, but I spent considerable time trying to search and had no luck.

  I encountered a problem trying to set up a temporary L2L VPN from a Subscriber with CISCO2911 sitting behind the router of the ISP of an ASA. ISP has informed that I can't ignore their device and complete the circuit Internet on the Cisco for a reason, so I'm stuck with it. The Setup is:

  company 10.1.17.1 - y.y.y.y - router Internet - z.z.z.z - ISP - LAN - 10.x.x.2 - XXX1 - ASA - 10.1.17.2 - CISCO2911 - 10.1.15.1 LAN

  where 10.x.x.x is a corporate LAN Beach private network, y.y.y.y is a public ip address assigned to the external interface of the ASA and the z.z.z.z is the public IP address of the ISP router.

  I have forwarded ports 500, 4500 and ESP on the ISP router for 10.1.17.2. The 2911 config attached below, what I can't understand is what peer IP address to configure on the SAA, because if I use z.z.z.z it will be a cause of incompatibility of identity 2911 identifies himself as 10.1.17.2...

  ! ^ ^ ^ ISAKMP (Phase 1) ^ ^ ^!
  crypto ISAKMP policy 5
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  lifetime 28800
  isakmp encryption key * address no.-xauth y.y.y.y

  ! ^ ^ ^ IPSEC (Phase 2) ^ ^ ^!
  crymap extended IP access list
  IP 10.1.15.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
  Crypto ipsec transform-set ESP-3DES-SHA 3rd-esp esp-sha-hmac
  card crypto 1 TUNNEL VPN ipsec-isakmp
  defined peer y.y.y.y
  game of transformation-ESP-3DES-SHA
  match the address crymap

  Gi0/2 interface
  card crypto VPN TUNNEL

  Hello

  debug output, it seems he's going on IPSEC States at the tunnel of final bud QM_IDLE's.

  What I noticed in your configuration of ASA box, it's that you're usig PFS but not on 2911 router.

  So I suggest:

  no card crypto OUTSIDE_map 4 don't set pfs <-- this="" will="" disable="" pfs="" on="" asa="">

  Then try tunnel initiate.

  Kind regards

  Jan

• Connected to the ASA via the "VPN Client" software, but cannot ping devices.

  I have a network that looks like this:

  

  I successfully connected inside the ASA via a software "Client VPN" tunnel network and got an IP address of 10.45.99.100/16.

  I am trying to ping the 10.45.99.100 outside 10.45.7.2, but the ping fails (request timed out).

  On the SAA, including the "logging console notifications" value, I notice the following message is displayed:

  "% 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; "Connection for icmp src, dst outside: 10.45.99.100 inside: 10.45.7.2 (type 8, code 0) rejected due to the failure of reverse path of NAT.

  I have a vague feeling that I'm missing a NAT rule of course, but not all. What did I miss?

  Here is my configuration of ASA: http://pastebin.com/raw.php?i=ad6p1Zac

  Hello

  You seem to have a configured ACL NAT0 but is not actually in use with a command "nat"

  You would probably need

  NAT (inside) 0-list of access inside_nat0_outside

  He must manage the NAT0

  Personally, I would avoid using large subnets/networks. You probably won't ever have host behind ASA who would fill / 16 subnet mask.

  I would also keep the pool VPN as a separate network from LANs behind ASA. The LAN 10.45.0.0/16 and 10.45.99.100 - 200 are on the same network.

  -Jouni

• SCCM Remote Client - disconnect the PCoIP Session

  Hello

  We have a problem on virtual machines Windows XP 64-bit with SCCM remote client.

  When the user approved the request, PCoIP session closes. This is not the case on the Windows 7 virtual machines.

  I checked pcoip logs and that:

  04/08/2013, 11:36:40.416 > RC LVL:2: 0 MGMT_IMG: CODEC: change of State of CODEC_DISABLED to CODEC_DISABLED

  04/08/2013, 11:36:40.416 > LVL:2 RC: COMMON 0: TERA_PCOIP: session_evenement = TERA_MGMT_SYS_SESS_EVENT_RESET, disconnect the cause (0xfffffe0c)

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 SERVER: main server: called cb_notify_session_status (mask 0 x 10) with tera_disconnect_cause (0xfffffe0c)

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 SERVER: server: TERA_MGMT_SYS_SESS_EVENT_RESET cause of disconnection (0xfffffe0c).

  04/08/2013, 11:36:40.416 > LVL:1 RC: SERVER-501: map_tera_to_vdp_connection_result_code: tera unknown disconnect cause(-500)

  04/08/2013, 11:36:40.416 > LVL:1 RC:-501 SERVER: server: map_tera_to_agent_close_code() failed due to disconnection (0xfffffe0c). With the help of PCOIP_AGENT_CLOSE_CODE_BROKER_INITIATED

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 SERVER: connection_closed: code = 2.

  04/08/2013, 11:36:40.416 > RC LVL:1: 0 VGMAC: the Session Statistics: average TX = 0.116288 average RX = 0.0140269 (Mbit/s) Loss=0.00%/0.00% (R/T)

  04/08/2013, 11:36:40.416 > RC LVL:2: 0 MGMT_SYS: closing of the Session remotely!

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 MGMT_SYS: *.

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 MGMT_SYS: *.

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 MGMT_SYS: *.

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 MGMT_SYS: *.

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 SERVER: Server mailbox: MBX_SHUTDOWN with agent disconnection (0x0) reason code

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 SERVER: Server mailbox: stop the mailbox message loop

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 SERVER: backend: had completed the message of the application

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 SERVER: backend: output

  04/08/2013, 11:36:40.416 > LVL:2 RC: 0 SERVER: the Server Cleanup: kill pcoip with agent disconnect reason code (0) and wait

  04/08/2013, 11:36:40.416 > LVL:1 RC: SERVER 0: map_agent_to_tera: DISCONNECT_GENERIC-> TERA_DISCONNECT_CAUSE_HOST_BROKER_GENERIC

  04/08/2013, 11:36:40.416 > LVL:0 RC: 0 MGMT_SESS: tear down the session

  04/08/2013, 11:36:40.416 > RC LVL:2: 0 MGMT_VCHAN: VChanPluginExit: closing the plugin 'VMware_Server '.

  04/08/2013, 11:36:40.447 > RC LVL:2: 0 MGMT_VCHAN: VChanPluginExit: Plugin 'VMware_Server' is closed.

  04/08/2013, 11:36:40.447 > RC LVL:1: 0 MGMT_VCHAN: = > parted with success all plugins VChan

  04/08/2013, 11:36:40.447 > LVL:2 RC: 0 SERVER: the Server Cleanup: detachment inputdevtap

  04/08/2013, 11:36:40.447 > LVL:0 RC: EXTERN 0: input_devtap == > can't get the process token for the user.

  04/08/2013, 11:36:40.447 > LVL:2 RC: 0 SERVER: the Server Cleanup: closing of mailboxes

  04/08/2013, 11:36:40.447 > LVL:2 RC: 0 SERVER: the Server Cleanup: free copy of the argument

  04/08/2013, 11:36:40.447 > LVL:2 RC: 0 SERVER: the Server Cleanup: complete cleaning

  Hi Linjo,

  Seems, all my problems are related to the type of OS client!

  I will deploy Windows XP 32-bit or Windows 7 for VDI other sites.

  BR

• Jack was very warm when you disconnect the plug iPhone

  When my iPhone 6 supported this morning, I noticed the plug that goes into the wall was pretty hot when I disconnected the unit from the wall.  I never noticed this before.  Is it a bad sign and is it safe to use?

  On the phone under 80% charge when you unplugged? If Yes, the cube would be hot, because the phone draws more power for the first 80% of the load, it then tapers. If you have any doubts bring it to an Apple store for the assessment.

• How to disconnect the access code from my iPad 2

  How to disconnect the access code from my iPad 2

  What do you mean by "disconnect"? If you mean stop using an access code then settings > password (enter your current password) > disable password

• SE connect/disconnect the 3g automatically

  Hello

  We have a Toshiba Portege R600, and working with a docking station to the office (with ethernet). But when you work in a home, we using 3g networks. My problem is when disconnect us the docking station, we are setting in network 3g connected automatically, and when the portege is connected to the 3g disconect station automatically.

  It is posible? because if I'm going to meet with my pc, I disconnect the docking and I lost some time to connect to the 3 g and I lost information.

  Thank you

  Anna Baker

  Hi Anna

  I don't think it's possible to do fully automatic LAN/WWAN switching again. Using Windows Vista/XP or Windows 7?

  /Nifer

• Satellite L750 system hangs after disconnecting the WLan

  I bought Satellite L750 series laptop I have connected Wifi. If I disconnect the Wifi system get hooked. I can't do anything to that. I've updated the driver software and I checked all the possibilities that my knowledge.

  > if I disconnect Wifi system and then get hooked.

  I assume you are using Fn + F8 to toggle the wifi.
  Right?
  Have you tried to restore the system to verify if there is a system problem?
  I think you should do and need to retrieve the laptop using the HDD recovery procedure
  Turn on the device, press F8, choose repair my computer, choose HARD drive recovery and follow the instructions on the screen, then you will get the system with the factory settings.
  Then test the WLan.

• Do I need to disconnect the Satellite L series battery if its full load?

  Hello world
  When my battery is fully charged, disconnect the battery?
  Sorry for my bad English, & thank you!

  N ° why you do that?
  I have never done this with my books.

• Equium 2000: How to disconnect the cables strip of motherboard

  Hallo,
  could you please someone describe to me how to disconnect the two flat-band-cables the Equium 2000 with the low Group (readers) motherboard, that the connectors don't get corrupted.

  Thank you!

  Harald mueller

  Hello

  I'm not 100 sure that cables say exactly, but at both ends of the connector, you should see little "clips" or "parentheses". You have to put on the side. So normally it should be possible to pull the cables. But if you do, you should be carefully.
  But if you have no experience of these things, you shouldn't do it. In this case, the best way is to ask the guy to service for assistance.

• Disconnect the cable in a VI script

  How to disconnect the wire between two terminals in a VI script?

  Get a reference to the thread and call the Delete method. If the wire is connected to multiple receivers, you can get references to the source and (other sinks), remove the wire, then reconnect to all receivers other than the one you want to disconnect.

• Disconnect the user from the sql server Server 2008 SQL server client

  Hello...

  Please can someone guide me on how to disconnect the server SQL server 2008 sql server user client if the client is more than 10 minutes of inactivity
  Thank you
  Salomé

  Hello

  SQL Server is not supported in these forums. Please ask the appropriate here Microsoft TechNet Ant:

  http://social.technet.Microsoft.com/forums/SQLServer/en-us/home?category=SQLServer

  Thank you.

• How do I Fix error code 43 CD. Windows disconnected the disk do not know how to reconnect.

  My Pavilion g7us Notebook Pcs Cd-Rom Drive showed a 43 error code and my computer has disconnected the Cd-Rom drive, and he said: it will not reinstall because there is a problem with the drive, how to fix my cd-rom so that I can start my backups and use my Dvd Player and burner.

  In addition, depending on the operating system, try following the steps under "Windows 7 or Windows Vista" or "Windows XP" in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• I plugged a wireless mouse for my laptop, but I can't seem to disconnect the touchpad

  I plugged a wireless mouse for my laptop, but I can't seem to disconnect the touchpad, what should I do?

  Hello Roberto,

  On how to disable the trackpad on a DELL computer, contact DELL.

• I get a server error live when I try to load Halo 2 in windows 7. I Shadow Run responsible, and I am disconnected. It worked fine on vista 64. Can I disable Windows Live? I use the game as independent.

  Upgrade to Windows 7 Pro 64.   Loaded Shadow Run, works well, tried to play Halo2, which was already on the machine, and it does not open.  I get an error message that the server is already running.  I tried the compadiblity box and disconnected the modum by forums, it still does not work.  Thanks for all the ideas.  Mike Moczan

  Hi, Mike Moczan,.

  Welcome to the Microsoft Answers site!

  I suggest you to load the game in a clean boot state to see if the problem is not caused by the interference of any third-party application.

  To perform a clean boot on a computer that is running Windows 7, follow these steps.
  1. click on start, type msconfig in the search box and press ENTER.

  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  2. in the general tab, click Selective startup.
  3. under Selective startup, clear the check box load startup items.
  4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
  5. click on OK.
  6. When you are prompted, click on restart.
  7. after the computer starts, check if the problem is resolved.

  If your issue is resolved, follow the how to determine what is causing the problem section in KB article to narrow down the exact source.

  http://support.microsoft.com/kb/929135.

  In addition, see the section on how to restore your computer to a Normal startup mode.

  Concerning
  Varun j: MICROSOFT SUPPORT
  Visit our Microsoft answers feedback Forum
  http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ and tell us what you think

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.