ASA vpn client

Similar Questions

• Unable to connect to other remote access (ASA) VPN clients

  Hello

  I have a cisco ASA 5510 appliance configured with remote VPN access

  I can connect all hosts on the INSIDE and DMZ network, but not able to access other clients connected to the same VPN.

  For example, if I have 2 clients connected to the VPN, customer and CustomerB, with a pool of vpn IP addresses such as 10.40.170.160 and 10.40.170.161 respectively, these two clients are not able to communicate with each other.

  Any help is welcome.

  Thanks in advance.

  Hello

  I'm a little rusty on the old format NAT, but would be what I would personally try to configure NAT0 on the 'outer' interface.

  It seems to me that you currently have dynamic PAT configured for the VPN users you have this

  NAT (outside) 1 10.40.170.0 255.255.255.0

  If your traffic is probably corresponding to it.

  The only thing I can think of at the moment would be to configure

  Note of VPN-CLIENT-NAT0-access-list NAT0 for traffic between VPN Clients

  list of access VPN-CLIENT-NAT0 permit ip 10.40.170.0 255.255.255.0 10.40.170.0 255.255.255.0

  NAT (outside) 0-list of access VPN-CLIENT-NAT0

  I don't know if it works. I did not really have to configure it on any ASAs running older software. There was some similar questions here on the forums for the new format.

  -Jouni

• ASA VPN clients

  I couldn't find the answer to this in google.

  You have to use the anyconnect software or you can use other as openvpn client software to connect to your asa.

  If it is for home, ASAs all equipped with 2 free licenses of AnyConnect Premium.

  You can even set up a VPN SSL without client using those and does not any client software - a simple browser.

  Purchase price for a small number of licenses AnyConnect is very cheap indeed.

  You can use generic third-party clients for IPsec VPN IKEv1 (not for the SSL VPN client-oriented).

• Configure Cisco ASA VPN client

  I did some research and the answers it was supposed to be possible, but no info on how to do it.  I wonder if it is possible to configure a Cisco ASA 5505/10/20 to be a customer to an existing (in this case) cisco vpn client.  The reasons why are complicated (and irrelevant IMO), but basically, I need to be able to make a small network that may be on this vpn rather than on individual computers.

  The vpn client is a Basic IPSec over UDP Cisco VPN to an ASA5505.

  So, how to set up an another ASA to connect to it as if it were a client?

  Hello

  Here is a document from Cisco on the configuration, the easy ASA of VPN server and Client

  Although in this case, they use a PIX firewall as a client.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805c5ad9.shtml

  Here's another site with instructions related to this installation program

  http://www.petenetlive.com/kb/article/0000337.htm

  I imagine that the site of Cisco ASA Configuration Guide documents will also give instructions how to configure it.

  -Jouni

• ASA VPN client certificate authentication

  Hi all

  We finished our from the ASA Firewall VPN client. Is it possible to authenticate users with certificate. Certificate itself being our ASA server.

  Our requirement is to have:-user must use one laptop company provided for the VPN connection. I think it's possible with certificate OmniPass. Y at - it another way to have this control.

  Thank you

  -John

  Hi John,.

  It is indeed possible to authenticate your users to VPN client with certificates and it will prevent guests who do not have the certificate installed on their computer to connect.

  In the subject to use the ASA CA Local, I advise you to use only if you have Anyconnect client and not the classic IPSEC client.

  The local ASA CA has been implemented for use for WebVPN and Anyconnect sessions only so I advise you to use an external CA if your customer is the IPSEC one.

  Kind regards

  Nicolas

• Assign the static IP address by ISE, ASA VPN clients

  We will integrate the remote access ASA VPN service with a new 1.2 ISE.

  Authentication is performed in Active directory. After authentication, can address assigned to a specific user of VPN by ISE IP?

  This means that the same VPN user will always get the same IP address. Thank you.

  Daniel,

  You can override the IETF-RADIUS-Framed-IP-Address in the authorization policy.

  However if I may make a suggestion:

  Unless you have only a handful of users to do so, it may be appropriate to assign the address of ISE pool or perform the mapping of LDAP attributes on ASA itself.

  In the latter case, the IP addresses are kept on the server as LDAP attributes and ASA will map the IP address. You don't want to keep address IP DB in several places.

  M.

• ASA VPN client and OWA Exchange/2013

  Hi all... quick question ASA...

  Does anyone know the status of support for OWA Exchange 2013 and the ASA webvpn client access?

  I know that the ASA has a model for 2010... It works with 2013? Is there is the 2013 model in the pipeline for the ASA?

  Thank you!

  Hi Paul,.

  There is an improvement (CSCul27869) that opens to Exchange 2013 be supported with ASA.

  CSCul27869
  It is an enhancement request to add support for OWA 2013 with webvpn.
  https://Tools.Cisco.com/bugsearch/bug/CSCul27869/?reffering_site=dumpcr

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Issue of ASA VPN client

  Hello.

  I have a question about a connection between an asa5505-sec-bun-k9 (who acts as easy VPN client) and an EASY VPN server.

  The connection with the easy VPN server is OK, but I can't connect to the internet and create VPN for my ASA5505 connections when I activated the feature.

  Is this a normal phenomenon with Easy VPN active customer?

  Cool

  Please, note useful

• VPN site to site & outdoor on ASA 5520 VPN client

  Hi, I'm jonathan rivero.

  I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.

  the executed show.

  ASA1 (config) # sh run

  : Saved

  :

  ASA Version 8.0 (2)

  !

  hostname ASA1

  activate 7esAUjZmKQSFDCZX encrypted password

  names of

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  address 172.16.3.2 IP 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 200.20.20.1 255.255.255.0

  !

  interface Ethernet0/1.1

  VLAN 1

  nameif outside1

  security-level 0

  no ip address

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/5

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  2KFQnbNIdI.2KYOU encrypted passwd

  passive FTP mode

  object-group, net-LAN

  object-network 172.16.0.0 255.255.255.0

  object-network 172.16.1.0 255.255.255.0

  object-network 172.16.2.0 255.255.255.0

  object-network 172.16.3.0 255.255.255.0

  object-group, NET / remote

  object-network 172.16.100.0 255.255.255.0

  object-network 172.16.101.0 255.255.255.0

  object-network 172.16.102.0 255.255.255.0

  object-network 172.16.103.0 255.255.255.0

  object-group network net-poolvpn

  object-network 192.168.11.0 255.255.255.0

  access list outside nat extended permit ip net local group object all

  access-list extended sheep allowed ip local object-group net object-group net / remote

  access-list extended sheep allowed ip local object-group net net poolvpn object-group

  access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  outside1 MTU 1500

  IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0

  no failover

  ICMP unreachable rate-limit 100 burst-size 10

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 access list outside nat

  Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1

  Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec kilobytes of life security-association 400000

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  card crypto VPNL2L 1 match for sheep

  card crypto VPNL2L 1 set peer 200.30.30.1

  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 20

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  !

  !

  internal vpngroup1 group policy

  attributes of the strategy of group vpngroup1

  banner value +++ welcome to Cisco Systems 7.0. +++

  value of 192.168.0.1 DNS server 192.168.1.1

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value splittun-vpngroup1

  value by default-ad domain - domain.local

  Split-dns value ad - domain.local

  the address value ippool pools

  username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15

  tunnel-group 200.30.30.1 type ipsec-l2l

  IPSec-attributes tunnel-group 200.30.30.1

  pre-shared-key *.

  type tunnel-group vpngroup1 remote access

  tunnel-group vpngroup1 General-attributes

  ippool address pool

  Group Policy - by default-vpngroup1

  vpngroup1 group of tunnel ipsec-attributes

  pre-shared-key *.

  context of prompt hostname

  Cryptochecksum:00000000000000000000000000000000

  : end

  ASA2 (config) #sh run

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  86400 seconds, duration of life crypto ipsec security association
  Crypto ipsec kilobytes of life security-association 400000
  card crypto VPNL2L 1 match for sheep
  card crypto VPNL2L 1 set peer 200.30.30.1
  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
  VPNL2L interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 20
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  tunnel-group 200.30.30.1 type ipsec-l2l
  IPSec-attributes tunnel-group 200.30.30.1
  pre-shared key cisco

  my topology:

  

  I try with the following links, but did not work

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml

  Best regards...

  "" I thing both the force of the SAA with the new road outside, why is that? ".

  without the road ASA pushes traffic inward, by default.

  In any case, this must have been a learning experience.

  Hopefully, this has been no help.

  Please rate, all the helful post.

  Thank you

  Rizwan Muhammed.

• ASA static IP Addressing for IPSec VPN Client

  Hello guys.

  I use a Cisco ASA 5540 with version 8.4.
  I need to assign a static IP address to a VPN client. I saw in the documentation Cisco that this can be done to validate the user against the local ASA and in the user account database, you assign a dedicated IP address, or using the vpn-framed-ip-address CLI command.
  The problem is that the customer never gets this address and it always gets one of the pool in the political group. If I delete this pool, the client can't get any address.
  No idea on how to fix this or how can I give this static IP address to a specific VPN client?
  Thank you.

  Your welcome please check the response as correct and mark.

  See you soon

• What VPN Client for ASA 5550 AnyConnect Premium connection?

  We have version9 a couple of ASA550 I want to put in place a VPN client for use with remote access to administration.  We have included AnyConnect VPN, Premium license peers 2 so I guess we can just use of Cisco AnyConnect VPN client.  I went to Cisco's Web site and it says that I don't have right to the last Anyconnect VPN Client 4.x but I don't have access to the version 3.x.

  The 3.x client is compatible with the ASA and also Windows 10?

  If Yes, what is the correct file to use, there are many files listed for download in AnyConnect 3.x?

  In addition, what is the difference between the AnyConnect 3.x and 4.x customer and why Cisco restricting 4.x?

  Jim

  AnyConnect 4.x has changed the licensing model. AnyConnect 4.x licenses are term based licensing vs perpetual 3.x. There are a number of other differences, mainly due to there being only two license types - more and Apex - no Mobile plus, Advanced Endpoint Assessment, shared VPN etc. Cisco offers a nominal or no license cost of migration until the end of 2015. (depending on what you have: positive Essentials or Apex at premium)

  AnyConnect 3.1 will work with Windows 10 and the latest version of the Software ASA (since Version 3.1.10010). Reference:

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  There are two ways it is distributed - as a stand-alone installation or package for the distribution of the ASA station. Both come in Windows, Mac OS X and Linux distributions. For a Windows client, you must use either:

  AnyConnect-Win-3.1.12020-pre-deploy-K9.ISO

  AnyConnect-victory - 3.1.12020 - k9.pkg

  .. .to the current version of these respective form factors.

• A VPN client / ASA cannot access the Internet.

  VPN clients can get to the servers internal/DMZ but not Internet. This is the partial config of the SAA. TIA

  Pool VPN 10.17.70.0

  DMZ 192.168.100.0

  172.0.0.0 internal

  -------------------------------------

  nonatdmz list of allowed ip extended access any 192.168.100.0 255.255.255.0

  access extensive list ip 172.0.0.0 nonatdmz allow 255.0.0.0 10.17.70.0 255.255.255.0

  standard access list splittunnel allow 172.0.0.0 255.0.0.0

  Global interface (10 outside)

  Global interface (Businesspartner) 10

  NAT (inside) 0-list of access nonatdmz

  NAT (Inside) 10 0.0.0.0 0.0.0.0

  NAT (DMZ) 10 0.0.0.0 0.0.0.0

  Vinnie, happy that you have found here.

  Telnet for asa by vpn session, you need to add this statement.

  management-access inside

  In this same connection see split tunnel vs local Allow only lan access, you can learn the differences and you will better understand your configuration asa related to ra vpn.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080702999.shtml

• All necessary licenses on ASA 5510 for old Cisco VPN Client

  We're trying to migrate our firewall Watchguard to a Cisco ASA 5510, who bought some time ago. For some reason, all of our users have already installed the old Cisco VPN client. I think it will work. Are there licensing issues on the 5510 I had to be concerned with?  No matter what special config that needs to be done on the 5510?

  Fix. You don't require licensing of AnyConnect of any type of configuration and the use of IKEv1 IPsec remote access VPN (which use the old Cisco VPN client).

  You will be limited to 250 active IPsec peers (remote access more no matter what VPN site-to-site) by the platform (hardware) device capabilities that are enforced by the software.

• ASA VPN server and vpn client router 871

  Hi all

  I have ASA 5510 as simple VPN server and 871 router as simple VPN client. I want to have the user ID and permanent password on 871 and not to re - enter username and password since 871 uses dynamic IP address and every time I have to ' cry ipsec client ezvpn xauth "and type user name and password.

  any suggestions would be much appreciated.

  Thank you

  Alex

  Do "crypto ipsec client ezvpn show ' on 871, does say:

  ...

  Save password: refused

  ...

  ezVPN server dictates the client if it can automatically connect with saved password.

  Set "enable password storage" under the group policy on the ASA.

  Kind regards

  Roman

• Remote VPN client and Telnet to ASA

  Hi guys

  I have an ASA connected to the Cisco 2821 router firewall.

  I have the router ADSL and lease line connected.

  All my traffic for web ports etc. of ADSL ftp and smtp pop3, telnet etc is going to rental online.

  My questions as follows:

  I am unable to telnet to ASA outside Interface although its configuered.

  Unable to connect my remote VPN Client, there is no package debug crypto isakmp, I know that I have a nat that is my before router device my asa, I owe not nat port 4500 and esp more there, but how his confusion.

  I'm ataching configuration.

  Concerning

  It looks like a config issue. Possibly need debug output "debug crypto isa 127".

  You may need remove the command «LOCAL authority-server-group»

  NAT-traversal is enabled by default on the ASA 8.x version. So you don't have to worry about NAT device in the middle.