Issue of ASA VPN client

Similar Questions

• Routing issue of Cisco VPN Client ASA

  Hi, I use a Barracuda NG for firewalls and I would use a Cisco ASA 5505 for VPN Client connections. But I have the problem that I can't get a connection to the VPN PC connected to the internal network. But I can reach the VPN connected PC from the inside. Here is a diagram of my network:

  cisco_asa_prob.jpg

  

  Here the IP Configuration and the routing of the Barracuda firewall table:

  screen_shot_2014-08 - 12_at_16.01.42.png

  

  I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

  The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

  Here is the config Cisco ASA:

   : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

  Can someone please help me solve this problem?

  When I tried to solve this I didn't choose which interface the Packet Tracer?

  The interface inside or DMZ interface?  Inside, he says it will not work with the dmz but the error did not help me

  Anyone here knows why it does not work?

  screen_shot_2014-08 - 12_at_16.34.57.png

  

  screen_shot_2014-08 - 12_at_16.33.06.png

  

  Hello

  Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

  entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

  Route by tunnel watch also with 255 administrative distance.  I've never used that in my scenarios... lets see...

  Concerning

  Knockaert

• Unable to connect to other remote access (ASA) VPN clients

  Hello

  I have a cisco ASA 5510 appliance configured with remote VPN access

  I can connect all hosts on the INSIDE and DMZ network, but not able to access other clients connected to the same VPN.

  For example, if I have 2 clients connected to the VPN, customer and CustomerB, with a pool of vpn IP addresses such as 10.40.170.160 and 10.40.170.161 respectively, these two clients are not able to communicate with each other.

  Any help is welcome.

  Thanks in advance.

  Hello

  I'm a little rusty on the old format NAT, but would be what I would personally try to configure NAT0 on the 'outer' interface.

  It seems to me that you currently have dynamic PAT configured for the VPN users you have this

  NAT (outside) 1 10.40.170.0 255.255.255.0

  If your traffic is probably corresponding to it.

  The only thing I can think of at the moment would be to configure

  Note of VPN-CLIENT-NAT0-access-list NAT0 for traffic between VPN Clients

  list of access VPN-CLIENT-NAT0 permit ip 10.40.170.0 255.255.255.0 10.40.170.0 255.255.255.0

  NAT (outside) 0-list of access VPN-CLIENT-NAT0

  I don't know if it works. I did not really have to configure it on any ASAs running older software. There was some similar questions here on the forums for the new format.

  -Jouni

• ASA VPN clients

  I couldn't find the answer to this in google.

  You have to use the anyconnect software or you can use other as openvpn client software to connect to your asa.

  If it is for home, ASAs all equipped with 2 free licenses of AnyConnect Premium.

  You can even set up a VPN SSL without client using those and does not any client software - a simple browser.

  Purchase price for a small number of licenses AnyConnect is very cheap indeed.

  You can use generic third-party clients for IPsec VPN IKEv1 (not for the SSL VPN client-oriented).

• Configure Cisco ASA VPN client

  I did some research and the answers it was supposed to be possible, but no info on how to do it.  I wonder if it is possible to configure a Cisco ASA 5505/10/20 to be a customer to an existing (in this case) cisco vpn client.  The reasons why are complicated (and irrelevant IMO), but basically, I need to be able to make a small network that may be on this vpn rather than on individual computers.

  The vpn client is a Basic IPSec over UDP Cisco VPN to an ASA5505.

  So, how to set up an another ASA to connect to it as if it were a client?

  Hello

  Here is a document from Cisco on the configuration, the easy ASA of VPN server and Client

  Although in this case, they use a PIX firewall as a client.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805c5ad9.shtml

  Here's another site with instructions related to this installation program

  http://www.petenetlive.com/kb/article/0000337.htm

  I imagine that the site of Cisco ASA Configuration Guide documents will also give instructions how to configure it.

  -Jouni

• ASA VPN client certificate authentication

  Hi all

  We finished our from the ASA Firewall VPN client. Is it possible to authenticate users with certificate. Certificate itself being our ASA server.

  Our requirement is to have:-user must use one laptop company provided for the VPN connection. I think it's possible with certificate OmniPass. Y at - it another way to have this control.

  Thank you

  -John

  Hi John,.

  It is indeed possible to authenticate your users to VPN client with certificates and it will prevent guests who do not have the certificate installed on their computer to connect.

  In the subject to use the ASA CA Local, I advise you to use only if you have Anyconnect client and not the classic IPSEC client.

  The local ASA CA has been implemented for use for WebVPN and Anyconnect sessions only so I advise you to use an external CA if your customer is the IPSEC one.

  Kind regards

  Nicolas

• ASA vpn client

  Hello world

  I would like to ask for help in order to correct a customer vpn tunnel. I'm not familiar with the AAS, so please do not laugh if I write something stupid

  So I inherit one asa, which has two interface used physical and vlan more. Outdoors, office, management and management. I use my computer on the vlan management, and I can reach the computers on the desktop (192.168.12.0/24) and the branch (192.168.10.0/24). I would realize that I connect to thrught houses a vpn, and I should reach the 12.x and 10.x network as I was in these networks (due to the microsoft allowed wirewall to the local network traffic).

  I inherited a vpn configuration which I added my user.

  I'm trying to cite only the relevant portion of config:

  SSH 192.168.99.0 255.255.255.0 management

  access extensive list ip 192.168.99.0 nonat_management allow 255.255.255.0 192.168.99.0 255.255.255.0

  access extensive list ip 192.168.99.0 nat_management_branch allow 255.255.255.0 192.168.10.0 255.255.255.0
  access extensive list ip 192.168.99.0 nat_management_office allow 255.255.255.0 192.168.12.0 255.255.255.0

  IP local pool ippool 192.168.99.100 - 192.168.99.200

  NAT-control
  Global 1 interface (outside)

  NAT (management) - access list 0 nonat_management
  nat_management_office list of access 5 NAT (management)
  nat_management_branch list of Access 10 NAT (management)

  192.168.99.50 management - dhcpd addresses 192.168.99.79
  enable dhcpd management

  L2TP strategy of Group internal
  monty password username * == encrypted nt
  monty username attributes
  Protocol-tunnel-VPN l2tp ipsec
  VPN-framed-ip-address 192.168.99.99 255.255.255.0
  attributes global-tunnel-group DefaultRAGroup
  ippool address pool
  Group Policy - by default-l2tp
  IPSec-attributes tunnel-group DefaultRAGroup
  pre-shared key *.
  tunnel-group DefaultRAGroup ppp-attributes
  ms-chap-v2 authentication

  I quote the encryption settings, because I can connect to asa, I think that I have problems with the nat or access rules.

  I have an ip local pool 192.168.99.100 - 192.168.99.200, but I have the fixed ip with the vpn-framed-ip-address 192.168.99.99 255.255.255.0

  Happened when I connect and try to reach the following computers:

  I can reach only a freenas 192.168.12.2, and I see in his journal that I have connected with 192.168.99.99 (vpn-framed-ip-address)

  I can't reach the computers on networks, however I have two nat rules, working when I'm in the office network 99.0

  access extensive list ip 192.168.99.0 nat_management_branch allow 255.255.255.0 192.168.10.0 255.255.255.0
  access extensive list ip 192.168.99.0 nat_management_office allow 255.255.255.0 192.168.12.0 255.255.255.0

  It seems that these two nat rules do not work with my vpn client.

  And it is very important to arrive at the asa with ssh through the tunnel, but I can't.

  I don't know if that is the ip address of the vpn client is in the management network, perhaps one should change to another network:

  for example 192.168.95.0/24

  A vpn asa for Dummies or any help is appreciated.

  Thank you very much

  Hi Chris,

  The following should help:

  access-list allowed 192.168.12.0 nonat_office 255.255.255.0 192.168.90.0 255.255.255.0

  In this way, returning office subnet pool VPN traffic is exempt from nat. And so you will not get the failure of RPF checking.

  In addition, you must change this:

  nat_vpn_office to access extended list ip 10.10.10.0 allow 255.255.255.0 192.168.12.0 255.255.255.0

  (incoming traffic on the VPN remote access would come from the VPN pool.) Not your home network.)

  You must have:

  No nat_vpn_office access list extended ip 10.10.10.0 allow 255.255.255.0 192.168.12.0 255.255.255.0

  access extensive list ip 192.168.90.0 nat_vpn_office allow 255.255.255.0 192.168.12.0 255.255.255.0

  NAT (outside) 5 nat_vpn_office list of outdoor access

  Hope this helps, and sorry for the delay.

  -Shrikant

  P.S.: Please check the question as answered if it was resolved. Do rates all useful messages. Thank you.

• Assign the static IP address by ISE, ASA VPN clients

  We will integrate the remote access ASA VPN service with a new 1.2 ISE.

  Authentication is performed in Active directory. After authentication, can address assigned to a specific user of VPN by ISE IP?

  This means that the same VPN user will always get the same IP address. Thank you.

  Daniel,

  You can override the IETF-RADIUS-Framed-IP-Address in the authorization policy.

  However if I may make a suggestion:

  Unless you have only a handful of users to do so, it may be appropriate to assign the address of ISE pool or perform the mapping of LDAP attributes on ASA itself.

  In the latter case, the IP addresses are kept on the server as LDAP attributes and ASA will map the IP address. You don't want to keep address IP DB in several places.

  M.

• ASA VPN client and OWA Exchange/2013

  Hi all... quick question ASA...

  Does anyone know the status of support for OWA Exchange 2013 and the ASA webvpn client access?

  I know that the ASA has a model for 2010... It works with 2013? Is there is the 2013 model in the pipeline for the ASA?

  Thank you!

  Hi Paul,.

  There is an improvement (CSCul27869) that opens to Exchange 2013 be supported with ASA.

  CSCul27869
  It is an enhancement request to add support for OWA 2013 with webvpn.
  https://Tools.Cisco.com/bugsearch/bug/CSCul27869/?reffering_site=dumpcr

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Issue of SSL Vpn client'

  you are not sure if it's possible/Device asa 5550 - but a customer can establish SSL VPN to the remote network and devices on the local network to access remote network printers?

  so you have a network client that creates an SSL VPN to network B network B configurable so that the automatic work met the same vpn ssl to a different IP address?

  I don't know if its just me, but I don't understand what you mean with that:

  so you have a network client that creates an SSL VPN to network B network B configurable so that the automatic work met the same vpn ssl to a different IP address?

  You can try to explain once more?

  Now I think tell you the following, please look at this:

  HQ - ASA - INTERNET - office2

  Now the office2 will a clientless vpn SSL to the ASA and subsequently, you want HQ in order to communicate with certain printers or servers to Desktop 2 via SSL vpn without customer... If that's the question the answer is no. clientless vpn SSL will only allow traffic to go from office2 at HQ and not all traffic , this will depend on which allows you to configure the clientless ssl (Smart tunnels, Port-forwarding, Plugins).

  Yet once I don't know if that is the question.

  Kind regards

  Julio

  Note all useful posts

• Issue of ASA vpn site to site isakmp

  Hello

  He has been asked to configure on ASA a new vpn site-to-site. For that vpn should I put:

  crypto isakmp identity address
  crypto ISAKMP allow outside

  .. the configuration of my identity crypto isakmp is automatic and isakmp crypto is not enabled on any interface. I love vpn with ike enabled on the external interface. My question is: why should I enable isakmp on the external interface and especially can create disturbances to ike vpn that are already in place?

  By elsewhere-group or tunnel-group strategy, it was me asked to set up, the two do not have indication of ike. Never seen this kind of configuration before vpn, something new.

  Thank you

  Hi, Giuseppe.

  The crypto isakmp command activate outside changed ikev1 crypto Enable outside in the new ASA versions you need not enable this.

  There is also no need configure isakmp crypto identity address such that it is set to auto.

  This command indicates that the tunnel would be negotiated on the basis of the IP address but since it is set to auto it on it own will therefore not need to specify this command.

  Yes, you can create a new group policy group for this new tunnel and tunnel and there should be no impact on other tunnels of work.

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• LAN ASA 5505 VPN client access issue

  Hello

  I'm no expert in ASA and routing so I ask support the following case.

  There is a (running on Windows 7) Cisco VPN client and an ASA5505.

  The objectives are client can use the gateway remote on SAA for Skype and able to access devices in SAA within the interface.

  The Skype works well, but I can't access devices in the interface inside through a VPN connection.

  Can you please check my following config and give me any advice to fix NAT or VPN settings?

  ASA Version 7.2 (4)

  !

  ciscoasa hostname

  domain default.domain.invalid

  activate wDnglsHo3Tm87.tM encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  interface Vlan3

  prior to interface Vlan1

  nameif dmz

  security-level 50

  no ip address

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain default.domain.invalid

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any

  inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 any

  outside_access_in list of allowed ip extended access entire 192.168.1.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 dmz

  local pool VPNPOOL 10.0.0.200 - 10.0.0.220 255.255.255.0 IP mask

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 524.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  Global 1 interface (outside)

  NAT (inside) 1 10.0.0.0 255.255.255.0

  NAT (inside) 1 192.168.1.0 255.255.255.0

  NAT (outside) 1 10.0.0.0 255.255.255.0

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map pfs set 20 Group1

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.0 inside

  SSH timeout 5

  SSH version 2

  Console timeout 0

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd dns xx.xx.xx.xx interface inside

  dhcpd allow inside

  !

  attributes of Group Policy DfltGrpPolicy

  No banner

  WINS server no

  value of server DNS 84.2.44.1

  DHCP-network-scope no

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec l2tp ipsec webvpn

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  Group-lock no

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelall

  Split-tunnel-network-list no

  by default no

  Split-dns no

  Disable dhcp Intercept 255.255.255.255

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout 30

  disable the IP-phone-bypass

  disable the leap-bypass

  allow to NEM

  Dungeon-client-config backup servers

  MSIE proxy server no

  MSIE-proxy method non - change

  Internet Explorer proxy except list - no

  Disable Internet Explorer-proxy local-bypass

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  address pools no

  enable Smartcard-Removal-disconnect

  the firewall client no

  rule of access-client-none

  WebVPN

  url-entry functions

  HTML-content-filter none

  Home page no

  4 Keep-alive-ignore

  gzip http-comp

  no filter

  list of URLS no

  value of customization DfltCustomization

  port - forward, no

  port-forward-name value access to applications

  SSO-Server no

  value of deny message connection succeeded, but because some criteria have not been met, or because of a specific group policy, you are not allowed to use the VPN features. Contact your administrator for more information

  SVC no

  SVC Dungeon-Installer installed

  SVC keepalive no

  generate a new key SVC time no

  method to generate a new key of SVC no

  client of dpd-interval SVC no

  dpd-interval SVC bridge no

  deflate compression of SVC

  internal group XXXXXX strategy

  attributes of XXXXXX group policy

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  Split-tunnel-network-list no

  XXXXXX G910DDfbV7mNprdR encrypted privilege 15 password username

  username password encrypted XXXXXX privilege 0 5p9CbIe7WdF8GZF8

  attributes of username XXXXXX

  Strategy Group-VPN-XXXXXX

  username privilege 15 encrypted password cRQbJhC92XjdFQvb XXXXX

  tunnel-group XXXXXX type ipsec-ra

  attributes global-tunnel-group XXXXXX

  address VPNPOOL pool

  Group Policy - by default-XXXXXX

  tunnel-group ipsec-attributes XXXXXX

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:a8fbb51b0a830a4ae823826b28767f23

  : end

  ciscoasa #.

  Thanks in advance!

  fbela

  config #no nat (inside) 1 10.0.0.0 255.255.255.0< this="" is="" not="">

  Add - config #same-Security-permit intra-interface

  #access - extended list allowed sheep ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

  #nat (inside) 0 access-list sheep

  Please add and test it.

  Thank you

  Ajay

• All necessary licenses on ASA 5510 for old Cisco VPN Client

  We're trying to migrate our firewall Watchguard to a Cisco ASA 5510, who bought some time ago. For some reason, all of our users have already installed the old Cisco VPN client. I think it will work. Are there licensing issues on the 5510 I had to be concerned with?  No matter what special config that needs to be done on the 5510?

  Fix. You don't require licensing of AnyConnect of any type of configuration and the use of IKEv1 IPsec remote access VPN (which use the old Cisco VPN client).

  You will be limited to 250 active IPsec peers (remote access more no matter what VPN site-to-site) by the platform (hardware) device capabilities that are enforced by the software.

• Remote VPN client and Telnet to ASA

  Hi guys

  I have an ASA connected to the Cisco 2821 router firewall.

  I have the router ADSL and lease line connected.

  All my traffic for web ports etc. of ADSL ftp and smtp pop3, telnet etc is going to rental online.

  My questions as follows:

  I am unable to telnet to ASA outside Interface although its configuered.

  Unable to connect my remote VPN Client, there is no package debug crypto isakmp, I know that I have a nat that is my before router device my asa, I owe not nat port 4500 and esp more there, but how his confusion.

  I'm ataching configuration.

  Concerning

  It looks like a config issue. Possibly need debug output "debug crypto isa 127".

  You may need remove the command «LOCAL authority-server-group»

  NAT-traversal is enabled by default on the ASA 8.x version. So you don't have to worry about NAT device in the middle.

• connect Cisco VPN client v5 to asa 5505

  I have remote vpn configuration issues between ASA5505 and Cisco VPN client v5. Successfully, I can establish a connection between the client Vpn and ASA and receive the IP address of the ASA. Statistical customer VPN windows shows that packets are sent and encrypted but none of the packages is received/decrypted.

  Cannot ping asa 5505

  Any ideas on what I missed?

  Try adding...

  ISAKMP nat-traversal crypto

  In addition, you cannot ping the inside interface of the ASA vpn without this command...

  management-access inside

  Please evaluate the useful messages.