Assortment of problems

Similar Questions

• Satellite L30 - 113 memory problem

  I have a Satellite L30-113 that does not have the right
  size of the memory.

  The system was shipped with 512 MB and 1 GB extra, I installed
  Stick, but for some reason any windows reports only 896 MB installed and graphics card
  use 128 MB. The BIOS also pointed out that only 896 MB of ram is installed.

  When I run the system information for windows it only detects 1 GB module
  Although if I remove a memory module and have either 512 MB or 1 GB installed
  It works very well.

  I also installed the latest version of the BIOS and does not seam to
  have had no effect.

  Also the two sticks of memory were tested in another laptop, so I know that both work.

  Are there problems with the mixture of sizes of memory in these laptops or to memory
  Poles should be assorted sizes?

  The operating system is Windows XP Pro

  * Excerpt from system information for windows
  The value of property *.
  * + Memory: + * summary
  + * Place: * + motherboard or motherboard
  * + Maximum capacity: + * 1024 MB
  + * Memory: * + Slots 2
  * + Error Correction +: * No.
  * + Physical name: + * matrix memory
  * + Operating system: + * memory
  * + The device index: + * J501
  + * Capacity: * + 1024 MB
  * + Memory + type: * DRAM
  * + Width of data: + * 64-bit
  * + Bank Label +: * channel B0
  * + Form factor: + * DIMM
  * + Total width: + * 64
  * + Type Detail: + * synchronous

  Thank you very much
  Matt Tyrrell

  I agree with Abe. I noticed a few comments about it in the forum, and it seems that the Satellite L30 should be upgraded with exactly the same modules.
  I mean that the modules must support the same speed (MHz), the same manufacturer and so on

  For me it s clear that other computers are able to manage these modules, but it seems as the can-do that L30!

• Problem reading SD cards with PC under Windows 7

  My computer running Windows 7 is no longer reads my SD cards.  There is not a problem with maps so my laptop can read them.  I used these SD cards in my PC several times before.  When I go to my computer - the SD card is not listed.  The computer recognizes when I have a USB flash drive installed.  Any help would be appreciated.

  My computer running Windows 7 is no longer reads my SD cards.  There is not a problem with maps so my laptop can read them.  I used these SD cards in my PC several times before.  When I go to my computer - the SD card is not listed.  The computer recognizes when I have a USB flash drive installed.  Any help would be appreciated.

  =================================================
  Apparently, you have an internal media player?

  If you go to... My computer / devices with removable storage... and
  the assortment of removable disks that are normally associated with
  different media player slots are not available... I would suspect
  hardware failure of the media player.

  It may be interesting to try to buy a cheap USB media player
  and use instead of the internal drive.

• We get an error "there was a problem, restart your PC. No changes"while trying to reinstall Windows 8

  * Original title: Windows 8 reinstall could not start

  Try reinstalling Windows 8 (x 64 OEM version), but after clicking on start, I get the following error:

  "There was a problem, restart your PC.  Has been no change. »

  Ditto for the Refresh tool.  Verification of the Solutions tool thinks for a minute, then disappears.  Have tried to introduce these tools after boot, as well as an assortment of other boards around the internet such as the cmd line queries.  Any thoughts?  Had the PC for a year now, no weird mods or alteration of configuration, just installed Office and a few games of limited resources.  As a single user, I have full administrator access.

  Hi Paul,.

  Thank you very much for taking the time to answer.

  The product key for Windows 8 on computers that are preloaded with are encrypted.

  For more information, see the suggestions provided by Andre Da Costa of the next thread.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/Windows-8-key-embedded-in-the-BIOS/ce42cbdb-914D-4346-93ed-a86a5a77aa9f

  I wish that you contact the Asus technical support and get the recovery disk to fix the problem more far.

  Please reply with the status.

• Problems with Rich Black in Illustrator

  I wonder if anyone has experienced this problem...

  Often, I work on ads for newspapers and may present works of art with intense black. So I use 100% K each time than black is used. But intense Black has been sneaking in drawings. For example, I was working with a file with 7 or so the work plans and noticed that many of my black items inexplicably were dark black. I went through all the blacks in the file and changed all blacks to 100% K. Then I registered under and selected the option 'save all work in a separate file plans. At the opening of the individual files that save on I noticed that some of the black elements have been reduced to dark black. At this point, I had to cross, and then reselect each black to make sure that it was not dark black. Is there a default setting in there which is causing this to happen. Any help on this would be greatly appreciated. It has been an ongoing and frustrating problem in my workflow.

  Thank you

  do you mean a particular intense black or a seemingly random assortment of CMYK?

  the document has already had her changed to RGB color mode (or vice versa)?

• BMCC/CinemaDNG RAW problem w / video (first 7.1 vs Resolve)

  I did some initial testing with 7.1, focusing on the characteristics of CinemaDNG, because this is by far my main interest for the update as an owner of BMCC/enthusiast. I do not work with the files correctly, or it seems that the debayer/interpreter RAW is significantly downgraded in the way which solve process files.

  After having a brief discussion on twitter with Al Mooney (@al_mooney) product manager for Adobe Premiere Pro, he encouraged me to consider on the forums. I decided to confront the problem in a quick video. 1. for people considering an optimal workflow of BMCC using first (I personally prefer to edit directly from first, don't use is not a proxy). 2. for Adobe to consider when they evolve to the incredible creation platform.

  I want to emphasize, I am NOT pixel peeping here, there seems to be a major loss for how first transformation / access RAW data.

  System:

  iMac late 2011, i7 3.4 w / Radeon 6970 m 2gig ram

  SSD, OWC - 12 GB OF RAM

  Mavericks fresh install w / 7.1 updated

  Camera

  BMCC RAW 29.97 interpreted to 23.98 (Firmware 1.4.2 last)

  Here's a little video (200 x speed) of the problem

  http://Vimeo.com/79208889

  
  

  Benjamin Reece

  work

  thedeltree.com

  personal

  tomoveyou.me

  Kevin,

  Thanks for the idea. I understand that other workaround solutions, here too, to add BMCuser workaround that someone suggested (using Speedgrade like this seems to have access to the full dynamic range CinemaDNG).

  Speedgrade using seems to be more ideal, because it requires less manuvering. In addition, make a note of all sequences is very heavy on a consistent basis. I prefer to get my house, or at least selects before proceeding to a rank of quick - but I also prefer to do a fast slope before entering a rough cut as I don't want to not cut with the poorly assorted color balance, or over/under exposed shots - much less see the customer. Finally, Speedgrade seems again ideal because it does not require messy back and forth if you need get in and out during the customer approval process. Save the color for the end.

  1 import CinemaDNG in first

  2. the Assembly to modify (or opening selects at least) in the first

  3 Quick rank in Speedgrade

  4. change rough/final first

  5. output to solve 10 via XML if need to adjust or if no track curves/movement necessary to use Speedgrade to the final color

  Let me know if this workflow is logical. Also, I assume that we are at least 6 months to 1 year to get this type of 'The Source settings' ability in first, so I could do a blog post workflow for people who are looking for something faster using Photoshop, Lightroom, resolve or After Effects to the rank before their sequences. (who defeated the purpose of the dealing first to natively edit CinemaDNG IMHO).

  Thank you!

  Benjamin Reece

  work

  thedeltree.com

  personal

  tomoveyou.me

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• MacBook Pro display problem

  Hello members of the community.

  As of recently, I have noticed some glitches when feeding on my MacBook or awakened from his sleep.

  The colors are distorted, usually with pink, green, or yellow blobs. Blobs cannot entirely replace the colors, they appear to be contained in a element would normally be. For example. the menu bar will be partially pink and white, but pink does not leave the menu bar in this area, and the Office has green lines on it.

  I tried to take a screenshot, but the problem resolves in about 20 seconds, but it's a recurring problem.

  It happens when I wake up, connection or not. I had also certain powers serious and problems of performance, such that my MagSafe LED would not illuminate when plugged on rare occasions, fan could turn unnecessarily, graphics performance were SUPER slow, and the health of my battery was running out quickly. I actually ran a report on the system at 2 different times and my quality of full load is depleting of 1.2% per charge cycle, which is very worrying. I went from 6281 mAh mAh 6138 maximum capacity after two cycles of load. I'm tracking closely it because at this rate, my battery will survive only at load cycles about 150 instead of the 1000 expected, gives me the idea that this could very well be a bad battery. The computer is also warm to the touch while you sleep, not connected to the power supply. I NAP active but even taking into account should not be hotter my iPhone did the same thing.

  I have reset the SMC, and it solved a couple of problems. The charger works fine now and my performance improved considerably (which made me feel better, either it is a high-performance laptop, a 11-inch MacBook Air should not he surpass), and battery life has improved. I feel even if it uses a lot of power in his sleep. Maybe I need to turn off the NAP and see if that makes a difference. The graphic bug still persists however, and I don't have enough time to see if the max battery is depleting again.

  In regards to the bug, is there something that can be done? Basically, I want to assure you that I took all appropriate measures or if someone else has this problem to see if it can be software related instead of my computer.

  I have the entry level MacBook Pro with the retina, last generation.

  Any constructive contribution welcome!

  See you soon.

  -adreaux

  Hello bernardn753,

  After reviewing your post, it seems that you are having problems with the screen showing strange things on it. Looks like you already have a troubleshooting. I recommend you read this article, as reset NVRAM would be to reset your screen resolution settings that should help.

  How to reset the NVRAM on your Mac.

  Thank you for using communities of Apple Support. Good day.

• with IOS 10.0.2 - 5s iphone Bluetooth problems

  Since upgrading ISO 10.0.2 my M50 from PLT Plantronics (helmet unique headset) do not reliably connects with my iPhone 5 more. I have to go to the settings, activate bluetooth turned off/turned on, touch the device on the bluetooth page, etc. Once it connects successfully, it will reconnect (if I turn off the headset and turn it back on) for a short period. The next day he does not connect itself but I play with bluetooth on the iPhone again.

  It has always worked perfectly before the 10th of IOS.

  And, as I noticed others mentioning, the volume is much lower with IOS 10. The maximum volume is much lower. I can barely hear it now, more normal background noise, while driving.

  I did:

  Forget this device for the PLT M50 and paired again (several times)

  I did a Reset Network Settings

  I don't know what else to do - but it's a 10.0.2 IOS issue.

  Hello AppleUser2k,

  Please ask questions about your problems of connection between your iPhone and your Plantronics headset since you upgraded to iOS 10. I understand how important it is to have your Bluetooth devices connect with your iPhone with reliability. Here's what I recommend.

  The first thing we want to make sure is that all your data is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, try the troubleshooting steps in this article to help: get help to connect a Bluetooth accessory with your iPhone, iPad or iPod touch device should also check with the manufacturer that the device has all the drivers and firmware to work with the new version of iOS.

  If you have checked everything and that you have installed the latest firmware or driver and always are problems, please be aware of your surroundings when you encounter these problems. If you can isolate the time or location, you see the problems, you can isolate the cause. You can even see this help article to ensure that you are not affected by outside interference: the potential sources of Wi-Fi and Bluetooth.

  Thanks again and have a great rest of your day.

• Problem after update 10.0.2 iOS iPhone touchscreen

  After I have updated to iOS 10.0.2, I noticed a problem with the touch screen. Using the position of the image on the right side, near the corner, the toushscreen does not work.
  For example: when you use the keyboard, I can't type the letter 'P', have trouble typing BACKSPACE. Using the Contacts app, I can't scroll through using the alphabet bar.

  Do what idea of the problem?

  Kind regards!

  Hi fabriciorela,

  Thanks for the upgrade to iOS 10! I understand that the right of your screen is unresponsive to the touch. You can try the steps in this link to fix the problem. If the screen of your iPhone, iPad or iPod touch does not respond to touch

  If it does not help the problem, try to restore the device to factory settings. I would like to backup your important data first.

  The backup of your iPhone, iPad and iPod touch

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod to factory settings

  Please use the Apple Support communities to post your question. Let us know how it turns out. Have a great day.

• Bluetooth connection problem iPhone - audio system Nissan after upgrade iOS10

  After iOS10.0.2 iOS9 on iPhone upgrade, I got a cordially problem receive calls raise Nissan car audio.

  I can make a call without any problem. Bluetooth connection is stable. I can download address book e.t.c. But I can't receive a call. I see the incoming call on the radio shows. After pressing the button "answer" on the car Audio System, audio between iPhone and Audio streams car breaks down.

  But the cellular connection remains active. I need to rotate the audio output on the screen of the iPhone car for iPhone and back to the car. After that, I can continue my call via the car radio.

  Thanks in advance

  Hello StasV,

  Thank you for using communities Support from Apple. I know having a problem with calls on your iPhone in your car, it's not what you expect. The good news is that these steps will be useful for your problem of phone calls while using the bluetooth in your car. Go to settings > general > accessibility > routing of Audio calls and the value headset/Bluetooth Headset and retest your question.

  Audio routing call - the iPhone user Guide
  Help to connect your iPhone, iPad or iPod touch with your car radio

  See you soon!

• 2 iphones on one iTunes, problem of photo icloud account

  OK, my brother-in-law just updated its OS on his Iphone. He shared an Apple ID with his wife, who has his own iPhone. They all have two backup only in iCloud. His problem is that his wife photos are now on his phone. How can he fix it?

  Get its own identifier Apple- create and start using a Apple - Apple Support ID

• Problem activation ISO 10 September 2016

  After my Ipad iOS 10.0.2 update I could not activate because it says I am not access with the original Apple journal. Makes no sense. I bought the new Ipad in seven of 2013 Dabs.com. She has been linked to my Apple account 10 days ago (I deleted my profile by own Apple support Web site suggestion as a way to fix my problem, the other restoration/upgrade to the Ipad with ITunes update). I contacted the support of Apple (I have two numbers in case Apple). Asked Apple support to provide a proof of purchase I made. Told me now the reception that I provided does not correspond to my Ipad, but Apple isn't going to help with all the details to help to regularize the situation. The Ipad is mine and well was linked to my account from the date of purchase in September of 2013 until I removed it at the suggestion of site specific help from Apple. I now do not have access to my ipad £460 for more than 10 days and have lost money and time talking to 4 different cooperatives of Apple, after 6 calls and none seem able to deal with a ridiculous situation. Alexandre Vitorino (Apple) seems to have the best handle on weird how this situation is. Please can someone fix this? A software update on an Ipad that I own shouldn't stop me using it and then force me to prove that I admit actually before I use it again! I'm a professional businessman who uses it for meetings of the Council. I have a receipt for my camera and get treated like a kind of criminal.

  My sincere sympathy for those who can't find their original receipt or forget their original log-in Ipad because Apple does not help, you and your Ipad will be also useless mine is currently!

  If you are in the same situation please confirm to this post. I can't be alone, if she feels like it!

  Post edited by: cibble10

  Lock activation occurs when the ID of original Apple blocking it does not match with your current Apple ID.

  Until you can bring a receipt valid from an Apple reseller or authorized, it's nothing you can do.

  BTW, the polling stations in this Apple-owned forums is prohibited. You can review the terms of use.

• Anyone know how to solve my problem? I can't import my photos from Iphone to computer. Sign says: Photos in the camera cannot be imported because the IPhone is locked with a password or read. My phone is unlocked. I've tried everything

  Anyone know how to solve my problem? I can't import my photos from Iphone to computer. Sign says: Photos in the camera cannot be imported because the IPhone is locked with a password or read. My phone is unlocked. I tried everything, every single idea. Without success! Any other idea?

  For example, you specify that the device does not display the lock screen, correct? Do you use Touch IDS? If so, try to put your finger on the device to see if it's what he wants.

  See you soon,.

  GB