Aurora - Premium option-DPN liquid cooling: 01YGW

Similar Questions

• HP Z840 workstation: for Z840 liquid cooling?

  I currently have a Z800 WS dual Xeon CPU and coolant.  I am scheduled for a new WS and watched the Z840 but I don't see an option of liquid cooling. I run the structural analysis software that allows me to analyze a load case by heart so more cores means a faster flow.

  I was told that the faster clock speed and multiple real cores will be the best, so what will work better CPU and RAM?

  Another question, is that HP has a Mobo that supports several consumers i7 cpu popular with a lot of ram? I don't know if the Z840 WS and processor Xeon is the best bet.  Are there other options?

  There is no option of liquid cooling for z840 systems. With current processors, we do not believe that the system requires liquid colling option. HP get a kit rather than high-performance cooling liquid cooling in air. I don't know when, but not a long time.

  The following quicspecs list the supported processors and the memory modules. This system supports INTEL® XEON® E5 and DDR4 - 2133 ECC Registered / RAM load reduced (LR).

  http://WWW8.HP.com/h20195/v2/GetPDF.aspx/c04400043.PDF

  For performance, it is not a simple question. It depends on your application such as processor, memory intensive, drive-training or other resource intensive applications.

• Area 51 - R2, liquid cooling noise?

  Hi all

  I got a whole new area 51 R2 as a warranty replacement for my previous Aurora.

  Is there something I have to ask the community here before he gets too late:

  When I start the computer (and a few minutes after) I can hear the sound of liquid (liquid Interior movement) and let me know if this is normal. Area 51 seems to be much quieter, however, never heard the liquid through my Aurora Office.

  Is there something I should be concerned? Is in normal?

  Is it possible that the amount of cooling in the machine to be less that ideal and for this reason to hear the sound?

  You guys can help me with this?

  Thanks in advance for your comments.

  I also hear that on my area 51 - R2. I found this document in the section manuals X 51 - R3, "Alienware - x 51-R3 to liquid cooling" that applies to all Alienware liquid cooling units. In this document, he says,

  "The sound is standard for all computers with liquid cooling units and . stops after a few minutes of computer use. »

  "The sound of bubbling is due to the air that is in the coolant . Assembly. When the temperature of the liquid rises, it expands and the air bubbles in the tube are removed. »

  Maybe that's what we hear.

• Alienware CPU liquid cooling and fans and power supply on the new motherboard

  Hello. Would be my Alienware Aurora R4 CPU liquid cooling and fans, and the power supply inside of light on a new motherboard which is in a different situation? Because my R4 Alienware Aurora case is too big and occupy us too much space, and my office is weak. Thank you.

  You can get a better response if you re - post it in the forum of the Club of Alienware .

• Start of Aurora R4 gel after the cooling pump

  I am desperate for some help I recently followed a thread that have instructions on how to fix a clogged liquid cooling pump and after difficulty had rerun which seemed to be fine, the processor cores slowed 50ish c after crossing successfully blocking even if bf4 caused to reach just below 100 c. fact some tests with temperatures with regular use intervened then for about 15 minutes, is come to a computer is turned off, trying to start it again, he started upward then made a windows config that caused a restart, at that time I got past the bios that warned me of the accident, then slowly leave bios much slower screen so I never saw him. After that he try to load windows but hangs at startup of windows only get a small part of the windows icon to actually show. All mind you my fan goes loud enough but not as it was pre liquid cooler maintenance but still working really, I'm afraid I've damaged the CPU but it seems that from what I read online that if I got to load windows at all it is in operation.

  Plug I know vvv

  Windows 7 Edition home premium

  I7 3820 3.60gh processor

  Invidia GTX 555

  8 GB RAM on 2 4 gig sticks

  WD xl500m

  Please HELP, I just followed guides and I took my time running, I had would not fry the CPU, I already have a h55 of corsair on how to improve the cooling that I thought would be best. At this point I just want someone to diagnose it please what can be wrong now.

  Update

  At down to CPU, all taking care to avoid static when you manipulate this taken CPU so much so he rested in a wooden Bowl for the duration of the cleaning operations. Cleaned of any thermal paste used with iso alcohol 91% out of the jaws of the unit, CPU, socket cooling and nowhere else that touched the metal. The plug itself did not have any direct exposure to the dough as well below the CPU, it was very good, all the pins left intact and had no discoloration. My cooling pump that I fixed previously obtained ventilated and cleaned up a bit more, this time making sure the water in the tank was 100% at level before sealing it upward.

  Then after watching some videos of people making those I sat the CPU in the socket, reapplied dough online about the same amount that the last company on the CPU first, tighten all fluid on the CPU coolers, and now I find myself just try not to be afraid to turn everything back on when he's back together.

  Wish me luck, and all the words of advice would still be appreciated.

• [Power Mac G5] Type of liquid cooling system?

  Y at - it anyway how to determine type of LCS just by looking at the case?

  We have old school Power Mac G5 DP 2, 7GHz (early 2005) we use for editing (well, for the last two years, he's right there and no one wants to touch this old piece of...). They will throw him in the year, and since I was take care of him for a while, I thought I'd take home when they do and use it as a backup machine for the data of my and my wife. I would like the max memory, put a few large hard drives (and small SSD, but there seems to be a lot of problems with this) and run the Linux command (more problems).

  But first, I have to clean the machine and look at the State of it. What particularly concerns me is the LCS (DP 2, 7GHz I) - these things have been prone to leaks and what I found there are at least three revisions of the LCS - second of them made by Panasonic seems to be the most reliable. I can't look inside, deeply, because it must be ready to use at least for another 3-4 months, I can do is to open the case and remove the front fan and look outside the heater.

  So this brings me to my question: Y at - it anyway to determine the type of LCS just by looking at the case?

  Thank you...

  Apparently, there were two models more prone to leaks than others, although still very rare. See this http://www.everymac.com/systems/apple/powermac_g5/faq/powermac-g5-liquid-cooling-infos-fuites-issues.html

  The damage inflicted by a system of flight are very serious, and it is almost impossible to hide or completely clean. As soon as you open the side panel on the Power Mac, you will easily be able to tell if this unit experianced a problem.

• Noisy liquid cooling system

  I have a HP Clubhouse Phoenix with liquid cooling. The fan has become noisy. After 2 hours with assistance today to find the noise, we found whence he came. They gave me a part number 657398-004 or 657398-003. This part is not in stock, and they had no idea when it would be available. Google search has a share of provider, but this game is abandoned. My question is has anyone know of a system that I could use to replace that defective compatible liquid cooling?

  Hello 731coach,

  I don't have a replacement for this part number, but if the fan itself became noisy, have you considered oiling it?

  Most of the fans can be lubricated. Sewing machine oil works very well. Away from stuff like WD-40.

  How to lubricate a noisy fan.

  Again, don't know if that's what you want to say as being the problem, but if yes, give the oil trick to try. Google fixing noisy fans computer to view the videos.

  It will be useful.

• T7910 part number, liquid cooling unit, Precision TMJK2

  Can someone tell me how I can find this;

  www.Dell.com/.../documents ~esupport-r7910-liquid-cooling-en-v1.aspx

  I checked with the people of Dell parts and they have never heard of him, but this video installation is obviously from Dell. It is also as a T7910 NOT a R7910 who said in the URL.

  Given that the other will probably also be eager to find that at some point... Here is a picture of one, the part number is 0TMJK2. Asetek is the company that actually makes it to Dell. its an OEM part however. You can not order or buy it directly from Asetek.

  Good luck to order property. I finally have someone found at Dell who might actually find the part number, but it was out of stock. She said that the top price was $139.99...

  

• Aurora R1 - R4 A - 51 Corsair h80i Corsware mind-Meld liquid cooling adapters-> 0 <-not available h55 h60 h75 h100i h105 also

  M M Mark II:

  Coolers of H80i/100i Sata-Fan area-51 & Aurora R1 - R4

  Quantity available: 0 (sold out since 3.16.15)

  

  Picture shows 7 pins of the Aurora - I also 5pin of area-51. An adapter like this is what Dell had to you when the pump of your clogged R4 for unresolved reasons not allowed & overheated your high dollar Ivy-E.

  I built the above adapter & I have enough power to do more than 9 of them for the aftrmrkt Corsair-type coolers in your area 51 & Aurora R1 - R4. Sold through eBay & here on the forum:

  

  -: 55/60/75/80i/100i/105? I have technology majik in mind-Meld w/CmndCntr-

  For h80i/100i - above - I used the correct 7pin to reconnect your bunch of overhead lighting, & you go your connector sata & pumps fan connect my sata-mutual Fan connectors. It is the Mark II version, where the rider to the ground happens in the sata connector. Crimping base & welding using correct pins & UL1009 BLK 22awg wire. 1 "wire >< 2.5"="" end-to-end.="" h55/60/75/105="" will="" use="" a="" similar="" setup:="" mark="" iii,="" see next post="">

  Do you need one? Meh. But if you do, CmndCntr will notice current pump execution status, you will not get the fan @ start up error, & your CorsairLink fact his majik via usb for temp and fan speed monitoring. If you don't have a link, then try it. The idea of the wire back as if it was b4 the swap. And you can pop your fans of the pump head, reconnect on sysfan, leave the CC to do its thing. Uninstall the link. It I said...

  Cost is $ 15, so you will not break try it. Ready to post on now. If you want to be on the shopping list:

  1. Carillon in this thread & say: to the bottom of my stranger with the mind-Meld (my R1, R4, A - 51 etc.)
  2. Follow it up w/a friend request
  3. I'll message back for your Paypal ID & we take care of the rest

  Of course you can look @ my pictures & make your own mind-Meld retro-fit-kit: details are brutally specified here, where you can buy a foot hold how/where your source material & build your:

  • The ALX files: Operation Mind-Meld: Command Center Retrofit for Aurora R4 overheating problem SOLVED! Corsair H55 H60 H75 H80i Area 51 h100i h105 how to project Corsair cpu cooler liquid beam = Corsware
  • http://en.community.Dell.com/Owners-Club/Alienware/f/3746/t/19585441

  

  left: simple wire used for the rider "son" of superior quality (chemical bonding) land of new gold-plated pin sata

  Middle: components used to adapt #2 - right: finished product

  below: more pinned on. Yours is ready to send out now.

  

  I had planned to welding - assembling 4 adapters over this weekend, but as John Lennon advised us:

  life is what happens to you when you're busy making other plans

  The foregoing were not welded or assembled yet: a good thing, too. If sell Mark III adapters in the post below, I can convert them more "Tesla Swiss Army knives" (below, add 2.50) If you wish.

  When your M - M adapter arrives, open your door case & plug it. Time is about to sing the words this moving Lennon - McCartney favorite - song right on then & there to your dear Alien:

  Close your eyes... don't be afraid... the monster of swap is gone... it is on the run... & your Daddy's here

  beautiful, beautiful, beautiful, beautiful boy...

  https://www.YouTube.com/watch?v=j0IMASimhRo

  The beautiful Lennon / Darling Boy - one of my favorite too - (as in Mr. Holland's Opus)

  Adapters Alienwair comes to be run to the top of the flag pole: Let's see who salutes...

  My R1 Aurora down with mind-Meld.

  I'll take a Mark III Tesla (Swiss Army Knife) version.

  Not sure why my cooler Asetek original works still after 4 years, but my Aurora-R1 must live forever.

  Who knows what brings the future. I don't know that I want my cooler Asetek replacement as new (not used or rebuilt). This card allows to use Contingency Plan-B (using a Corsair/Asetek proven cooler).

• ReadyNAS 516 with liquid cooling

  is it possible to place a liquid cpu cooling on the readynas 516 cpu?

  Thanks, I'll look for another way to cool the unit, then transcoding 1080 p mkv files

• BIOS R4 Aurora missing options

  Hello

  I have a R4 with a build-date late 2013 (see datasheet below) version of the BIOS A11 running. I installed my videocard to an EVGA GTX 1070, and when I went into the BIOS, I noticed that the CPU power management Configuration page is now empty... is there literally no options at all. I'm missing all parameters that were there, including basic multipliers and other parameters of overclocking.

  Selection of the "load OC level 1" or "load OC level options 2" in the previous page had no effect on the missing parameters. I downloaded and re-flashed with the A11 BIOS update on the Dell Support site, but there has been no change.

  Main screen of the BIOS:

  

  The Advanced tab:

  

  CPU power management Configuration screen:

  

  I'm not sure what happened, or even when it happened. I can't be sure the timing of the correlates of problem BIOS to upgrade the hardware... it was a month since I was last in the BIOS. Also, at the same time, I applied a large update of Windows (the Windows 10 anniversary update) and installed a new its PCIe card. Too many changes to be able to cancel for testing purposes.

  Any ideas what's happening? I'm unable to OC my computer.

  Data sheet:

  Aurora R4, the Service tag

  BIOS version A11

  Win 10 Pro (x 64) v1607 (Build 14393)

  Core i7 - 4820K @ 3.7 GHz

  EVGA GTX 1070 FTW ACX3.0

  16 GB of RAM

  512 MB SSD / 1 TB HARD drive

  Heyo noodle,

  CASS ole was asked if I could put some info here, so here goes:

  Recently, I update my R4 Aurora as well.  A little older than you, I have an i7 3930 and it was A3 BIOS about it.  I've updated my BIOS before installing my Radeon R9 380 4gig and 16gig new RAM card.  I had Flash the BIOS A05 first then A11 BIOS on the Dell site.  I installed the A11 version about a month ago.  I checked my BIOS and I have the same options that Cass ole, looks like.

  http://i655.Photobucket.com/albums/uu272/Chuckrock2004/dellscreen.jpg

  I also have the same version of Windows 10.

  Chuck

  I don't have an its PCIe card.

• How do I remove the "premium" option of images appearing as search results

  Knew not even about them until we chose and bought almost a picture of "premium" of $250 for use in one of our messages.  Don't want that to happen accidentally.  If we can eliminate these from our search results?  Thank you!

  In your search options, be sure to select the $ and $$ and not the $$$

  

• Missing 309g: 3 Photosmart Premium options for Scan-&gt; computer

  I used to have 3 options on the Scan-> computer screen.  Now I only have the picture to the file Option and creates a jpeg file, I think.  How can I return the 3 options.  I did a reset to the factory settings and used app doctor Scan from HP.  Thank you

  Hello

  Assuming that I understand your intention, while clicking Scan on the front panel of the printer, and then clicking on computers, only one option appears, am I right?

  Forums, open the HP Solution Center software and click on the settings button.

  In the selection of the Section Scan "Scan to... Setup '.

  In the left pane to select the scan shortcuts required and click on add or the arrow button to move it to the right pane.

  Once all required option listed as available in the right pane, click Refresh the device.

  That should restore this option in the front panel.

• Cooling system Alienware Aurora R4

  Due to several accidents on my R4 Aurora, I google after the reason because these crashes, and I read that a problem could not work liquid cooling system. I live in Zurich in Switzerland, where I can buy a new cooling system?

  eBay Europe... examples of US stock cooler ... 'none' wide wide 120x25mm or 120x38mm should be ok... Google images Corsair H80i

  

  replace the stock R4 Alienware Aurora CPU cooling pump

  R4 (need advice)

  

  R4 premium 38mm large radiator manufacturer 01YGW (google/bing/eBay or Dell Sales)

  The thermal high quality grease if your cooler is delivered without any substantive multi-orientation

• replacement fan on the cooling system liquid on HPE h9 - 1215t Office in Phoenix

  Speak with technical support, they identified the fan on my liquid cooling on my new computer does not work correctly.  It does not start by itself, but if I give it move a bit, he starts and is still spinning.

  I really want to send it and leave a computer for a few weeks. I can easily replace the fan myself - but I can't find a replacement part or a fan number anywhere.

  Does anyone know the numbers of replacement parts and where to buy one?

  Thank you

  Product number: D7W28AV

  • • Windows 7 Home Premium 64
  • • 3rd generation Intel® Core™ processor quad-core i7-3770 [3.4 GHz, 8 MB of shared cache]
  • • Liquid cooling solution
  • • 2 GB Nvidia GeForce GT630 [DVI, HDMI, and VGA via adapter]
  • • 16GB DDR3 1333 MHz SDRAM [4 DIMMS]
  • • 256GB Solid State Drive
  • • 1 TB 7200 RPM SATA hard drive
  • • Microsoft Office Trial
  • • $20 OFF Norton Internet Security™ 2013 - 36 months
  • • Blu - ray player & SuperMulti DVD burner
  • • DVD SuperMulti burner
  • • 15-in-1 reader cards, 4 x USB 2.0 (front), 2 x USB 3.0 (top)

  So I bought a fan used on ebay-

  So that was the same part number, it not was not the same exact fan (no lights, no plastic), but it has perfectly aligned, uses less amps and worked without problems.

  My original fan: PVA092g12h-p28-ee

  Fan I bought-

  PVA092g12h no options