autonomous access point 1602 with three SSID

Similar Questions

• Unique SSID to the autonomous access point

  Hello

  My question is that if I have one SSID on an autonomous access point while I use the vlan native too. I mean what's the best practice in this case, if the vlan wireless say 10.

  Also I have to use the bvi-1 or I have to creat bvi another for this vlan?

  Thank you

  In my experience it's not a must to use native vlan.

  No, you should use only one interface BVI.

  Just like that:

  Ter of conf
  !
  Dot11 ssid ABC
  VLAN 10
  Open authentication
  Authentication-key wpa version2 management
  WPA - psk ascii cisco123
  Comments-mode
  !
  d0 IND
  SSID ABC
  encryption aes encryption vlan 10
  !
  D1 IND
  SSID ABC
  encryption aes encryption vlan 20
  !
  d0.10 IND
  encapsulation dot1q 10
  !
  D1.10 IND
  encapsulation dot1q 10
  !
  gig0.10 IND
  encapsulation dot1q 10
  !
  int bvi1
  IP address

  Concerning

  Remember messages useful rates

• How to set up the access point 1602 I just bought

  Hello world

  Hope you can help. I just bought an AIR-SAP1602I-A-K9 with an internet provider. With her, I also bought a power injector. I tried to use it as a standalone AP. It does not come with any instruction, and I'm not good at Wifi config. I hope you can help... My requirement of adjustment is very simple:

  -Create and broadcast the SSID called MYCSL

  N ' not no authentication or encryption. (is this open authentication?... so that people just plug the SSID as the user can start to cruise internet without putting in any key.)

  -The access point does not have a static ip assigned, instead, he gets an IP from one of my dhcp server in the network.

  -How to connect my laptop to configure via web http?

  Can you tell me what should be configured? Although it is a new product from a legitimate retailer... Cisco said that they could not support it without any contract of Starnet... as a consumer... they should give the kind of grace period to support the new products... In any case, hope you can help me out here :)

  I thank very you much for your help in advance.

  Takami Chiro

  Hi Takami,

  Take a look at one of the previous announcement. I would be more similar. Hope this will help you keep started. If you are the kind of things anywhere you please come back the Forum and someone will be able to help you.

  https://supportforums.Cisco.com/discussion/12217126/access-point-air-SAP...

  Hope that helps.

  Concerning

  Najaf

• Accept clients according to their power RSSI in autonomous access point

  I want to allow only users who are close access point to strong power RSSI and require low power RSSI other users to connect to other AP closest to them

  I use standalone AP 1130 g

  You can change the flow but it is global. You can disable discounted data on a given access point that allows only devices that can associate with 48mbps or 54 Mbps. If you want.

  Here is a link that explains the data to a standalone access point rates.

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.4_10b_JA/config...

  Sent by Cisco Support technique iPhone App

• AP 2702i as autonomous access point?

  Hi all

  We bought just the AIR-CAP2702I-E-K9 a few days ago. We want to use it as a standalone AP. The problem is that the device won't be configurable somehow: "conf t" does not work, not even after a "debug console cli capwap. The fact is that the AP continues to give the following error message:

  % CAPWAP-3-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.

  The fact is that we will not deploy this AP with a WLC. Is it possible or workaround to convert the CAPE based IOS in a basic stand-alone SAP version?

  Concerning

  NO.

  Hello

  Have you downloaded this image:

  http://software.Cisco.com/download/release.html?mdfid=284362257&flowid=3...

  Be aware that the independent IOS for the 2700 has limited features. Since the 2700 is a novelty, the standalone IOS is wireless site-only for investigation.  It is not intended to serve the customers as of yet.

  How to convert:

  http://rscciew.WordPress.com/2014/05/07/access-point-conversion-lap-to-a...

  http://www.YouTube.com/watch?v=QQ_NuxdRhQ4

  See the same type of position: https://supportforums.cisco.com/discussion/12254031/2702i-convert-autono...

  Concerning

  Remember messages useful rates

• L2 roaming with 2 autonomous access points?

  Hello

  Is it possible for 2 1130AG in stand-alone mode to quick support layer 2 roaming?

  My clients are a mix of clients of compatible and not cisco cisco ccx.

  (Authentication could be open or WPA etc.)

  If so, do 1 AP do acts as a WDS?

  I fell on the docs that say I need a WLSM and that an acting as a WDS AP don't work...

  If I do not use WDS and simply have 2 AP with the same SSID: -.

  If I only use open authentication, then the roam would be a little faster?

  The AP would update switches upstream MAC tables when a customer changes AP?

  Thank you

  Oh, I see now. You get absolutely L2 roaming out of the box. It's all part of the 802.11 Protocol - the customer will inform current accreditation which he left, which AP it will and then he will wander. With open authentication or PSK, it will be almost transparent to the client.

  Cisco Secure fast roaming is an entirely different topic. In the above case, if the customer is using the PEAP Protocol, it will need to authenticate to the RADIUS server whenever he roams to a new AP. Cisco FSR puts cached credentials in the WDS AP for fast authentication, which takes the RADIUS server outside the process. This significantly speeds up a course for users of the EAP, and it is especially noticeable (and necessary) for wireless IP phone users.

  Again, I hope it helps!

• MAC filter with autonomous access points

  Hi all

  A very simple question... I want to create local wireless networks using autonomous APs for the first time. I know this can all do with a trivial way controller, but this project can't stretch to that...

  • Can I use MAC filtering on autonomous APs to restrict clients associate?
  • I think that it will be 1240AG devices, but I guess the answer is the same for all models?
  • Can I mix MAC filtering with WEP/WPA? And use MAC filtering without encryption?

  Thank you!

  Paul

  PS. I know filtering MAC is terribly weak, but it is a requirement here...

  Yes, you can:

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15filt.html#wp1034987

  Stupid requirements.

  Thank you

  Chris

• I can't delete files in Access Point 1602 ROMMON mode

  Hello:

  I want to know if it is possible to remove files or directories that are currently allocated in the flash memory. As you can see in the following output, I'm in ROMMON mode and one of the images cannot start propoerly.

  AP: dir flash:
  Directory of flash: /.

  10 drwx 832- ap1g2-k9w8 - mx.153 - 3.JBB
  7 - rwx 230 env_vars
  drwx 5 0 ?
  6 - rwx 1048 private-multiple-fs
  39 384 drwx configs
  8 drwx 64 ap1g2-k9w7 - mx.152 - 4.JB6
  41 drwx 832 ap1g2-k9w7 - mx.153 - 3.JD
  265 - rwx 349557 crashinfo_20160705-223838-UTC

  7404544 bytes available (24531456 bytes used)
  PA:

  Best regards.

  OK, let's do this easily.

  If independent IOS, this is what you want the PA to start with, the more simple (and fast) to get this race is to format the flash of the AP (command: format flash :).)

  When formatting is finished, load the standalone IOS using the method of the Mode button.

• MIB for channel RF/setting read on autonomous Access Points

  Hei everyone.   Does anyone know if there is a channel RF of SNMP mib sfor reading/setting and other RF settings on stand-alone 1131AG Accesspoints. In my network, we use "less congested frequency" choice for the selection of the channel and wants to be which is the result of this.

  Best regards, Roy

  "Less populated frequency" does not... be together your AP to a specific channel or put in evidence that channels 1, 6 or 11.  You can use a mib to seethe list mib browser... This migh link... help tram know if its different from the 1131AG:

  http://www.oidview.com/MIBs/9/Cisco-dot11-if-MIB.html

• How can configure auronomous with WPA2 pre-shared key access point

  I worked with the 4400 WLC series and set up access points aironet 1140, and all work without any problems.but when I tried to configure the autonomous access point I couldn't configure the AP with WPA or WPA2 preshared key and I could configure it with WEP, I want to help here.

  Wi - Fi Protected Access 2 (WPA 2) Configuration example
  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008054339e.shtml

  Please rate when useful or appropriate.

• Access Point WAP200 is compatible with the injector WAPPOE12?

  Hello!!!

  I want to bring the power of an Access Point WAP200. I need to know if the WAPPOE12 injector is compatible with this kind of Access Point.
  I deployed 108 AP WAP200 in a wireless network and I want to know what type of power injectors, I use in this set.

  Thank you!!
  Best regards, Carlos

  Hi cramosfors. The search of the forums I found this.

  http://homecommunity.Cisco.com/T5/access-points/WAP200E-with-WAPPOE12/m-p/204398/highlight/true#M798...

• PS B110a - wireless configuration will fail if the network has multiple access points

  Photosmart B110a (CN245B) wireless AIO printer.

  I have several wireless access points using the same SSID to provide coverage over a large area. When you install the printer on the screen TouchSmart wireless installation fails. Print report reveals the following error:

  "More than one access point/router wireless was found which matches your network name (SSID). If this is not intended, your HP printer can connect to the wrong network. »

  In my case this IS planned but there seem to be no available option to answer "OK, just connect to any point of access by using my SSID.  If I turn off all but one the APs configuration complete OK. If I have to do every time I turn on the printer the printer is USELESS for me.

  Did I miss something?

  sijomi

  This should not be a problem.  I have a B110 (and another 10 or so HP wireless printers) on a network of airports with 5 access points and they just connect.

  Here are a few suggestions:

  1. don't use WEP - use WPA or WPA2 with a 13 + character password.

  2. enable the SSID broadcast on all access points

  3. do not use the MAC filtering acddress

  4. make sure "AP isolation" or "isolated wireless" is disabled.

  5. make sure that you are not on a private network, virtual, or connected to your network of comments.

  6. If different strings on access points do not work, try the same channel.

• The upgrade of Cisco 1600 access points

  A customer has Cisco 1600 12 access point and they want to add 3 access points. These access points are autonomous access points and the customer is tired to make individual changes by access points.  I suggested that the new access point be base controller, so my question; These existing access points can be upgraded to LWAPP? Or do need to be replaced? Or this controller one web-based access to existing contact points and be controlled.

  so my question; can these existing access point be upgraded to LWAPP? Or do they need to be replaced?

  Yes, existing AP can be converted into TOUR mode with a recovery image. Here's how you can do it (note that there are several ways) http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/ http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/ is the good idea to get a WLC (like 2504) to manage in a simple way, rather managing them individually. See below the product bundles available. If this is the case, you will get with license 25AP 2504 for almost for free when you buy 2 x 1702. Make sure that you choose the product of appropriate regulatory AIR-AP1702I-A-WLC HTH Rasika * Pls note all useful responses *.

• Access point of the AIR-CAP1602E-N-K9

  Hello

  can someone help me set up AIR-CAP1602E-N-K9 as autonomous access point.

  This is a new default affecting by my knowledge, it's a point of access controller based pls if help how to convert in autonomous access point and the image that is compatible with that.

  Hi Kamal,

  Hope links below will keep you started with LWAP autonomous.

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/u...

  https://supportforums.Cisco.com/docs/doc-14960

  http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

  For standalone AP, you can use the configuration below. In the link below, you can skip the configuration under 'bridge Configuration.

  https://supportforums.Cisco.com/document/61936/autonomous-AP-and-bridge-...

  Hope that helps.

  Concerning

  Najaf

• Help AIR-LAP521-G-E-K9 wireless access point

  Hello everyone,

  is there anyone who can give me guidance on how to configure an access point wireless AIR-LAP521-G-E-K9 offline? I tried to connect to a standard 1 GB switch, feed it with an IP via DHCP, it responds to the PING, but when it comes to detect in the CCA (3.1), it says unable to connect without even asking username and/or password. Try to connect to it via HTTP or HTTPS does not work either.

  Perhaps someone could explain to me what I am doing wrong?

  Thanks in advance.

  Stefano.

  Stefano,

  The 521 AP series can operate in light or autonomous mode. If your AP is currently the light image above we can convert by using tftp. (I suspect it does, as shown in light AIR - LAP number while AIR - AP is generally self-contained)

  The best way to check is to check the details of neighbor of cdp for the version of the software AP (or connect to the console of the AP and issue a 'show version').

  If the software has 'k9w7' in the name, which is autonomous. If she has "k9w8" then it is light. When operating in light you will be not able to telnet/ssh or go to the web page of AP.

  To convert your autonomous access point, please follow the procedure described here:

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp160918

  -Patrick Croak

  TAC wireless