AP 2702i as autonomous access point?

Similar Questions

• Unique SSID to the autonomous access point

  Hello

  My question is that if I have one SSID on an autonomous access point while I use the vlan native too. I mean what's the best practice in this case, if the vlan wireless say 10.

  Also I have to use the bvi-1 or I have to creat bvi another for this vlan?

  Thank you

  In my experience it's not a must to use native vlan.

  No, you should use only one interface BVI.

  Just like that:

  Ter of conf
  !
  Dot11 ssid ABC
  VLAN 10
  Open authentication
  Authentication-key wpa version2 management
  WPA - psk ascii cisco123
  Comments-mode
  !
  d0 IND
  SSID ABC
  encryption aes encryption vlan 10
  !
  D1 IND
  SSID ABC
  encryption aes encryption vlan 20
  !
  d0.10 IND
  encapsulation dot1q 10
  !
  D1.10 IND
  encapsulation dot1q 10
  !
  gig0.10 IND
  encapsulation dot1q 10
  !
  int bvi1
  IP address

  Concerning

  Remember messages useful rates

• Accept clients according to their power RSSI in autonomous access point

  I want to allow only users who are close access point to strong power RSSI and require low power RSSI other users to connect to other AP closest to them

  I use standalone AP 1130 g

  You can change the flow but it is global. You can disable discounted data on a given access point that allows only devices that can associate with 48mbps or 54 Mbps. If you want.

  Here is a link that explains the data to a standalone access point rates.

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.4_10b_JA/config...

  Sent by Cisco Support technique iPhone App

• autonomous access point 1602 with three SSID

  Dears.
  I'm 11 1602 sap ap configuration in one of our client's site... he wants three SSIDs, one of them for wireless ip phones.
  the problem that I am facing is when I set up the port of the ap in the trunk to allow 4 VLANS, vlan for ap and the rest three VLANS for SSID. I can reach the point of access and the SSID not broadcast... I already configured my core switches with dhcp for VLANs, but it does not work...
  switches to kernel running in vrrp active passive scenario...
  Please guide me in this setting because I'm not very familiar with wireless solutions.
  What is the best practice for this... How to do it.

  Sent by Cisco Support technique Android app

  Hi Mohammed,.

  Have you added 'mbssid' in the config.

  Reference: https://supportforums.cisco.com/docs/DOC-16087

  Also join the running configuration.

  Thank you

  Victor

  Help others using the system of rating and marking answers questions like "answered."

• MAC filter with autonomous access points

  Hi all

  A very simple question... I want to create local wireless networks using autonomous APs for the first time. I know this can all do with a trivial way controller, but this project can't stretch to that...

  • Can I use MAC filtering on autonomous APs to restrict clients associate?
  • I think that it will be 1240AG devices, but I guess the answer is the same for all models?
  • Can I mix MAC filtering with WEP/WPA? And use MAC filtering without encryption?

  Thank you!

  Paul

  PS. I know filtering MAC is terribly weak, but it is a requirement here...

  Yes, you can:

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15filt.html#wp1034987

  Stupid requirements.

  Thank you

  Chris

• L2 roaming with 2 autonomous access points?

  Hello

  Is it possible for 2 1130AG in stand-alone mode to quick support layer 2 roaming?

  My clients are a mix of clients of compatible and not cisco cisco ccx.

  (Authentication could be open or WPA etc.)

  If so, do 1 AP do acts as a WDS?

  I fell on the docs that say I need a WLSM and that an acting as a WDS AP don't work...

  If I do not use WDS and simply have 2 AP with the same SSID: -.

  If I only use open authentication, then the roam would be a little faster?

  The AP would update switches upstream MAC tables when a customer changes AP?

  Thank you

  Oh, I see now. You get absolutely L2 roaming out of the box. It's all part of the 802.11 Protocol - the customer will inform current accreditation which he left, which AP it will and then he will wander. With open authentication or PSK, it will be almost transparent to the client.

  Cisco Secure fast roaming is an entirely different topic. In the above case, if the customer is using the PEAP Protocol, it will need to authenticate to the RADIUS server whenever he roams to a new AP. Cisco FSR puts cached credentials in the WDS AP for fast authentication, which takes the RADIUS server outside the process. This significantly speeds up a course for users of the EAP, and it is especially noticeable (and necessary) for wireless IP phone users.

  Again, I hope it helps!

• MIB for channel RF/setting read on autonomous Access Points

  Hei everyone.   Does anyone know if there is a channel RF of SNMP mib sfor reading/setting and other RF settings on stand-alone 1131AG Accesspoints. In my network, we use "less congested frequency" choice for the selection of the channel and wants to be which is the result of this.

  Best regards, Roy

  "Less populated frequency" does not... be together your AP to a specific channel or put in evidence that channels 1, 6 or 11.  You can use a mib to seethe list mib browser... This migh link... help tram know if its different from the 1131AG:

  http://www.oidview.com/MIBs/9/Cisco-dot11-if-MIB.html

• How can configure auronomous with WPA2 pre-shared key access point

  I worked with the 4400 WLC series and set up access points aironet 1140, and all work without any problems.but when I tried to configure the autonomous access point I couldn't configure the AP with WPA or WPA2 preshared key and I could configure it with WEP, I want to help here.

  Wi - Fi Protected Access 2 (WPA 2) Configuration example
  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008054339e.shtml

  Please rate when useful or appropriate.

• The upgrade of Cisco 1600 access points

  A customer has Cisco 1600 12 access point and they want to add 3 access points. These access points are autonomous access points and the customer is tired to make individual changes by access points.  I suggested that the new access point be base controller, so my question; These existing access points can be upgraded to LWAPP? Or do need to be replaced? Or this controller one web-based access to existing contact points and be controlled.

  so my question; can these existing access point be upgraded to LWAPP? Or do they need to be replaced?

  Yes, existing AP can be converted into TOUR mode with a recovery image. Here's how you can do it (note that there are several ways) http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/ http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/ is the good idea to get a WLC (like 2504) to manage in a simple way, rather managing them individually. See below the product bundles available. If this is the case, you will get with license 25AP 2504 for almost for free when you buy 2 x 1702. Make sure that you choose the product of appropriate regulatory AIR-AP1702I-A-WLC HTH Rasika * Pls note all useful responses *.

• Access point of the AIR-CAP1602E-N-K9

  Hello

  can someone help me set up AIR-CAP1602E-N-K9 as autonomous access point.

  This is a new default affecting by my knowledge, it's a point of access controller based pls if help how to convert in autonomous access point and the image that is compatible with that.

  Hi Kamal,

  Hope links below will keep you started with LWAP autonomous.

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/u...

  https://supportforums.Cisco.com/docs/doc-14960

  http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

  For standalone AP, you can use the configuration below. In the link below, you can skip the configuration under 'bridge Configuration.

  https://supportforums.Cisco.com/document/61936/autonomous-AP-and-bridge-...

  Hope that helps.

  Concerning

  Najaf

• Help AIR-LAP521-G-E-K9 wireless access point

  Hello everyone,

  is there anyone who can give me guidance on how to configure an access point wireless AIR-LAP521-G-E-K9 offline? I tried to connect to a standard 1 GB switch, feed it with an IP via DHCP, it responds to the PING, but when it comes to detect in the CCA (3.1), it says unable to connect without even asking username and/or password. Try to connect to it via HTTP or HTTPS does not work either.

  Perhaps someone could explain to me what I am doing wrong?

  Thanks in advance.

  Stefano.

  Stefano,

  The 521 AP series can operate in light or autonomous mode. If your AP is currently the light image above we can convert by using tftp. (I suspect it does, as shown in light AIR - LAP number while AIR - AP is generally self-contained)

  The best way to check is to check the details of neighbor of cdp for the version of the software AP (or connect to the console of the AP and issue a 'show version').

  If the software has 'k9w7' in the name, which is autonomous. If she has "k9w8" then it is light. When operating in light you will be not able to telnet/ssh or go to the web page of AP.

  To convert your autonomous access point, please follow the procedure described here:

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp160918

  -Patrick Croak

  TAC wireless

• to convert 1142N AP autonomous lightweight access point

  Hello

  I have 4 1142N access points are all points of light access. Because I don't have a controller, I need to convert to standalone AP.

  I went through document cisco 1142, where it is mentioned that "the access point 1142 doesn't have the default IP address"

  I know procedure to convert offline in which I need to connect ap to the TFTP 10.0.0.1 with the ip address by default, but as for 1142, we do not have the default ip address. What is the procedure to convert offline?

  I have to assign a pool in one of the local switch and connect the ap to these switches with vlan, so she will receive the IP address of the DHCP server?

  But how can we without default IP address? I wonder about this...

  If I did not turn on where I can assign pool dhcp... what should I do?

  Please suggest me to convert 1142 standalone AP ap...

  I will be thankful to get the right answer...

  Hi Vinod,

  Here's the resolution...

  The image that is on the device's LWAPP, not the autonomous... If you want to use the AP in stand-alone mode, then the image must be W7...  It's...

  C1140-k9w7 - tar.124 - 21A .JY .tar not c1140-rcvk9w8 - tar.124 - 23c.JA.tar

  Please feel free to download any image from the below link and perform the conversion of image LWAPP to stand alone...

  http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=IOS+Software&mdfid=282439881&treeName=Wireless&mdfLevel=Model&url=null&modelName=Cisco+Aironet+1140+Access+Point&isPlatform=N&treeMdfId=278875243&modifmdfid=null&imname=&hybrid=Y&imst=N

  the methos to convert is...

  Download TFTPd32 of google and install it on your PC... point of the image that you downloaded on the TFTP server.

  Connect a cable ethernet between your notebook and AP... both should be on the same subnet... Connect a cable from the console and access the hyperterminal console with the command... Make sure that you are able to ping the PC and AP and vice versa!

  AP > en

  AP #debug lwapp console cli or debugging console cli capwap

  T AP #config

  AP (confg) int FA 0

  AP(confg-IF) ip addr (same subnet as the laptop)

  End AP(confg-IF)

  Force - reload DOWNLOAD - AP #archieve sw / overwrite tftp: / /.

  Force - reload DOWNLOAD - AP #archieve sw / overwrite tftp: / /<10.0.0.5>/c1140-k9w7-tar.124-21a.JY.tar

  The above command will do it for you!

  Let me know if that answers your question...

  Concerning

  Surendra

  ========

  Please don't forget to rate the post if this has been useful for you or useful

• The Access Points of 1142 conversion of autonomous to LWAPP

  Hi all

  I'm trying to convert 5 1142 APs to LWAPP... they came as autonomous APs out of the box, but the client decided to go the unified road, so I need to convert them to finish the job.  I tried to use that tool to upgrade to ver 3.4 and it say that the AP 1142 is not supported by the upgrade tool

  Is there another way to do this?

  Thanks in advance!

  Console or SSH to your access point and enter the following command:

  Archive Download-sw tftp://x.x.x.y/c1140-rcvk9w8-tar.124-21a.JA.tar

  x.x.x.y = the address of your tftp server.

  just like the upgrade to any newer device of Cisco. Of course you need a running tftp server, ect.,...

  Good luck to you.

  Doug

• Ordered the wrong access point!

  I thought that I had ordered a 1130ag but looks like I ordered a 1131ag LWWAP.

  Please could someone tell me what the difference between a 1130 and 1131. I understand I can load the IOS on the light AP software using a tftp server, but I do not know which exit to load on this subject. 12.3JX, 12.3JA, 12.3JEA, 12.3JEB! can anyone help please? either by the way, I am in the United Kingdom, do not know if this affects image to install. Thank you.

  Hi Paul,.

  This happens all the time, so it shouldn't be a problem :) I'm guessing that you have received this AP - AIR - LAP1131AG - x - K9 LWAPP. When you really wanted this AP - AIR-AP1131G-x-K9 Cisco IOS software. Look at the comparison;

  http://www.Cisco.com/en/us/products/ps6087/products_data_sheet0900aecd801b901c.html

  That being said, you should be good to go with 12.3 (11) JA1.

  To access Cisco Aironet to Cisco IOS version 12.3 Points (11) JA1

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b11jar1n.html

  Cisco IOS version 12.3 (11) JA1 supports 32 MB independent platforms. 16 MB platforms and platforms supported by Cisco IOS version 12.3 (8) JA and earlier versions (350, 1100, 1130, 1200 and 1230 access points and access point/bridge 1300 series) are supported by Cisco IOS version 12.3 (8) JEA1.

  Do not install a "JX" (it is a software image support to upgrade and recovery Cisco Lightweight Access Point Protocol (LWAPP));

  These release notes describe features, improvements, and caveats for Cisco IOS release 12.3 (11) JX1.

  Note: This version must be loaded on points of access to the plant or by using the lightweight stand-alone mode upgrade tool. Your access point may become unusable if you install this software without using the upgrade tool.

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b311jx1.html

  Returning to standalone Access Point

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.

  By using a TFTP server to revert to a previous version

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  --------------------------------------------------------------------------------

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.

  Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access point.

  Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.

  Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 9 after the access point reboots, reconfigure using the GUI or the CLI.

  This doc.

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  I hope this helps!

  Rob

• Cisco 1602i series Access point installation

  Hello everyone. I tried to configure cisco AIR-CAP1602i-E-K9 series access point is default for the configuration files and other settings, I guess you are looking for WLC. but I do not have a WLC I want to configure the AP a standalone conceerne Access point. I connected via switch where all the ports on the switch are vlan 10 switch is connected to a router and I have configured the router as DHCP server. It is my first time that I've never touched a cisco point for configuration of access. below is the error that was coming up on the screen countinously when I access the AP via the console. Kindly any assistance in this regard would be highly appreciated. Thank you

  * 00:18:46.324 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:19:31.824 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:19:36.828 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:19:36.948 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.218, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
  * 00:19:42.824 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

  * 00:19:51.823 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:20:37.323 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:20:42.327 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:20:42.447 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.219, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
  * 00:20:48.323 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

  * 00:20:57.323 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:21:42.822 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:21:47.826 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:21:47.946 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.220, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
  * 00:21:53.822 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

  * 00:22:02.822 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:22:48.322 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:22:53.326 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:22:53.446 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.221, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)
  * 00:22:59.322 Mar 1: % 3-CAPWAP-ERRORLOG: did not get the server DHCP server log settings.

  * 00:23:08.322 Mar 1: % 3-CAPWAP-ERRORLOG: could not resolve CISCO-CAPWAP-CONTROLLER
  Not in a bound State.
  * 00:23:53.821 Mar 1: % 3-CAPWAP-DHCP_RENEW: could not find WLC by using DHCP IP. Renew DHCP IP.
  * 00:23:58.825 Mar 1: % 3-CAPWAP-ERRORLOG: event white 38 & combination of State 2.
  * 00:23:58.945 Mar 1: DHCP-6-ADDRESS_ASSIGN %: BVI1 Interface assigned address DHCP 10.10.0.222, mask 255.255.255.0, hostname AP64f6.9dee.87d1

  Translate "CISCO-CAPWAP-CONTROLLER"... the domain server (255.255.255.255)

  If you do not have WLC, you will need to convert this access point in stand-alone mode. See below on this post. You must required image before this conversion. If you have a support contract with Cisco you can download from Cisco.com

  https://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

  https://mrncciew.com/2013/12/13/AP-conversion-using-mode-button/

  HTH

  Rasika

  Pls note all useful responses *.