Bad calling pool

Similar Questions

• NML bad call

  ReadyNAS RN104
  OS: 6.6.0
  App: nas-transmission

  Faild start because getting an error message: bad call NML

  Any idea?

  Thank you

  App: nas-transmission

  Version: 2, 92 - nt2

  I have reinstalled twice and it works again...

• Acer Aspire XP, will not load, gives calling pool bad error bluescreen 0x000000c2 (0 x 00000043, 0xc6f6c000, 0x00000000, 0x00000000)

  Have acer aspire one, it turns on appares to load windows xp but stops and has a pool caller bad blue screen, it lasts for a half second, so had to video screen to get the code 0x000000c2 (0 x 00000043, 0xc6f6c000, 0 x 00000000, 0 x 00000000). NetBook then passers-by to start in safe mode, last good con fig etc.

  You can choose one of them, but shut up just go back on screen. Went out disk hard netbook has no CD drive, put in the caddy and connected to another computer, can access all the files came out RAM and installed on another computer, is very well... Hard drive so OK. and Ram OK, so it's XP drivers...?

  took a hard drive of lenovo and put it in the acer, 4 months he turned acer and it works very well and is much faster.

  now I know his thinking about windows xp vista or windows7 operating system update.

  looked at windows xp folder driver thought about reinstall but it is best just to remove / upgrade the system

  No new hardware in six months.

  blue screen comes on during a half sec in safe mode, then restarts.

  pressed F8 got more options said to not restart if fail, then it would freeze on blue screen.

  said press alt gr f10 or f12 to get factory files but the option isn't there.

  When I mounted the disc via caddy with the lenovo there only one partition so no recovery is prescent.

  all user files can be viewed and copied, fortunately...

• Blue screen - Reel Bad Call

  I have a computer on which I can start is longer.  Using the hard disk to try to boot from I get bad_pool_caller 0x000000c2 (0 x 00000043, 0 x 0, 0000000 0000000, 0xc797D000).  I have a windows XP disc and when I try to repair the operating system or start from the disc - I get the same message with the second parameter changed - 0xc797 becomes 0xC4D3D000 and other channels.  From time to time, it will say physical memory dump.  I tried unplugging all devices, try the last known, tried to start in safe mode and perform a clean boot - none of them work.  Also I have run diagnostics on hardware and all past.  Any help would be appreciated.

  Hi Charles

  Try the steps in the article that I provide and leave me if your problem is solved

  http://www.ehow.com/how_5781000_fix-bad-pool-caller.html

  Bravo!

• Why do I get 'Bad call Dll Convention'?

  Hello

  the gall attached contains an experimental to read dll in LV 8.6 and use in VB6.

  The zip file contains the vi (adding 2 numbers), LV, VB6 project.

  The service seems to work.  He adds the numbers, but still, it gives the error "Bad dll calling convention".

  I think I did good. I used the Conventioin of the Standard call.  I used Double in LV and long in VB.

  How can I get rid of this error?

  Sombody allows this example on his machine.  Maybe it's something to do with my specific machine?

  VB usually gives the error "Bad DLL calling Convention" when you said an incorrect function.  This can be as simple as exporting with __cdecl instead of __stdcall (although this will crash more likely only), or it could be that because of the function declaration to say the battery is placed in a terrible state because the DLL call placed more or less data on the stack that VB should based on your statement.

  In your specific case, I see a few problems.   For reference:

  In LabVIEW, is your equivalent C function prototype as shown in your project file:

  Double AddNumbers (double * xY, double x, double y)

  In VB, your statement is:

  Declare Sub AddNumbers Lib "D:\NI Projects\eDAS400\DLL\LVDLL Experiment\SharedLib.dll" _

  (ByVal x As Double, ByVal y As Double, xy As Double)

  The first "double" in the C prototype means that the function in the DLL call will return a double.  In your VB prototype, by declaring "Sub" you are, in essence, says VB you don't expect the DLL to return data.  It is a likely cause of your error.  To resolve this issue, change to say "Declare function", and then add 'Double' at the end of the statement.

  The second problem I see is that in your prototype C, the first parameter is passed by reference (like a pointer).  However, your statement of VB, passes all ByVal.  You must change this option to make the parameter that returns data (in this case xY) is passed ByRef.

  Finally, it seems that your parameters in the function of C are probably not in the order that you expect.  I expect to be x, y, xy (which you have in the VB declaration), but the order in the C (ie. in the DLL) function is not the same.  This results in a funny behavior.  The order must match between the two.  To resolve this, I recommend you actually change the LV DLL so that settings are exported in more logical x, y, xy order.

  I think this should take care of your problems.  Sorry so lengthy, but I wanted to make sure that you understand the 'why' on this one because it can be a common error trying to create/call VB dll.

  Jason

• Win 8 PC crashes when I try to run or to reinstall Firefox. Bad BSOD pool header

  Since yesterday, Firefox crashes my PC. I did a search by a duct add on that was appeared and ran malware and registry cleaners. I also uninstalled Firefox.

  Computer works normally, but I can't re install Firefox which is my favorite browser. Each resettlement attempt ends in BSOD and a shtting down and restart and a suggestion that I search online for bad pool header.

  I've read about it and it doesn't seem to be a solution for me and a bit of his somewhat advanced, so I would ask instead for my question before you start tweaking the computer in many different ways,

  Thank you for any input! I need my Firefox to operate effectively :)

  BTW I run Windows from a regular desktop to start no new app/charms interface (ugh). So all the instructions would be most useful by using standard windows commands old school.

  I'll just add that it seems that the error can be with the font cache:

  STACK_TEXT:
  fffff880 ' 19492248 fffff802' 5fef68a4: fffff901 00000000'00000019 00000000'00000021 ' 015f7000 00000000'00001060: nt! KeBugCheckEx
  fffff880 ' 19492250 fffff960' 000b9f91: fffff901 '015f7000 00000000 00000000' fffff901'00000001 00000000' 64667454: nt! ExFreePool + 0 x 792
  fffff880 ' 19492330 fffff960' 000ca86d: fffff901 ' 00c82a08 fffff901 '052f2ab0 fffff901' 015f7020 fffff880 ' 194923e0: win32k! EngFreeMem + 0x21
  fffff880 ' 19492360 fffff960' 000ca07f: fffff901 '052f2ab0 00000000'00000003 00000000'00000000 fffff901' 00c829b0: win32k! bLoadGlyphSet + 0xe5
  fffff880 ' 19492390 fffff960' 000cb6e9: fffff880 00000000'00000003 00000000'00000001 00000000'00000000 ' 194926e0: win32k! bReloadGlyphSet + 0x18f
  "fffff880 ' 19492520 fffff960' 000cb620: fffff901'00c829b0 fffff880 ' 00000001 00000000 00000001' fffff880 ' 194926e0: win32k! ttfdQueryFontTree+ 0x61
  fffff880 ' 19492580 fffff960' 000cb91c: fffff960'000cb5a8 fffff901'00 c 67350 00000000'00000000 00000000'00000000: win32k! ttfdSemQueryFontTree+ 0 x 78
  "fffff880 '194925b 0 fffff960' 000d98cf: fffff901 00000000' fffff901 ' 00144030 00000000 00000000' fffff880 ' 19492b 28: win32k! PDEVOBJ::QueryFontTree+ 0x6c
  fffff880 ' 19492660 fffff960' 000d896e: fffff901'0008 has 010 fffff880 ' 19492938 00000000 00000000' fffff960' 00033998: win32k! PFEOBJ::pfdg + 0xdf
  "fffff880 ' 194926 d 0 fffff960 ' 0006c8e9: ffffffff 'ffffffff fffff880 ' 19492998 fffff880' 19492898'00000000 fffff880: win32k! RFONTOBJ::bRealizeFont+ 0x4e
  fffff880 ' 19492830 fffff960' 00129476: 00000000'00000000 00001598'00000000 00000000' 656d616e 73a 30000'00000000: win32k! RFONTOBJ::bInit+ 0 x 737
  fffff880 '194929f0 fffff960' 0012972f: 00000000'00000000 00000000'00001598 fffff880'19492 b 20 00455ed8'00000008: win32k! ulGetFontData2 +0 x 46
  fffff880 '19492ae0 fffff960' 0012969a: 00000000'00000000 00000000'00000000 00000000' ffffffff ffff90a0'216f69ef: win32k! ulGetFontData+ 0x5b
  fffff880 '19492b 30 fffff802' 5fcdd453: 00000000'00000000 00000000' 0035e0f8 fffff880 '19492ba8 00000000' fefbc000: win32k! NtGdiGetFontData+ 0 x 106
  fffff880' 19492b 90 00000000' 7760b9aa: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiSystemServiceCopyEnd + 0x13
  00000000' 0035e0d8 00000000'00000000: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000: 0x7760b9aa

  It's the same type of error, as reported in this this thread.

  Try to rebuild the cache of police:

  Rename the FNTCACHE. DAT (in C:\Windows\System32 folder).

  Rename the FNTCACHE. DAT to something like FNTCACHE.old

  Restart the computer and let Windows re - create the FNTCACHE. DAT

  In addition, right now 'disable' Driver Verifier:

  Windows key + S > type verifier.exe and press 'Enter' on the keyboard > clear the existing settings > finish > click 'Yes' to the message to delete the settings and exit the program

  For Windows 7, the following article, can explain how the problem arises:

  http://support.Microsoft.com/kb/2908190/en-us

• Date format blackBerry Smartphones bad call log

  Hi, I just noticed very strange format of call logs... observe:

  

  in the column on the right ago early in the first line (time/min), on the other lines I would expect date (day/month)... but only the first issue fits... it seems to be Connect minutes! :

  

  as you can see, I called the number 30 minutes ago, there a good hour Journal (01:30) and journal to correct day (27.6 is today) but shows a few minutes instead of months!

  I have the same problem. If you select the English language (Option > Language), you can see the log the correct day. I think that, Czech translation contains some bugs. :-(

• Smartphones blackBerry corrupted or bad call sound

  It's the second time that this has happened over the last 4 weeks.

  When you make a call, the sound is a noise clicking that mutes the sound in. The conversation is impossible. Reset (soft or hard) does not solve the problem. The only way I could get was to reinstall the OS (do an update).

  This time, I noticed that the problem happened right after that I got the headphones into the socket. I tried to put the helmet on. Sounds of music always playing good. Tried turning of service, bluetooth etc and turn back on. No use.

  I am running 4.6.0.297 on a "BOLD".

  The phone is like a telephone, only good unsuable for music and texting. I'll update later today to 4.6.0.304 and see if that helps.

  I guess that something is getting damaged. Any ideas?

  I would like to know if it is a bug in the software, or a difficult question and I should consider getting a replacement until it is too late. But I have the feeling that, until it becomes a problem more recurrent THAT RIM won't be able to do big thing with her.

• Recompose + pool stuck in Admin view

  Hi all

  So I hate to list the many questions/problems, we are affected by all grouped together, but we are sure to have questions that I feel should not occur.

  And please note that I started working with VMware, so I'm not an expert, just trying to learn best practices.

  View environment:

  7 host ESX - mvn1 - mvn7 (v4.1 u1)

  2 servers connection - mvc1 + mvc2

  1 security Server - mvs1 (with hope to put in place a second shortly)

  1 replica server - mvr1

  Shared storage between all hosts via iSCI

  They are as follows (and any help what do I get on part or all of the questions would be greatly appreciated):

  A. first of all, I noticed that it takes more than one hour to clone a machine model/create a Pool of 1 VM / create linked Clone pool. Size of the model is about 30g. I've seen articles indicating that this is normal, it just seems like we want to optimize it a little more to have 'a' VMs created more quickly.

  B. in the admin view, I have a pool that seems an orphan and will remove itself from the view of the pool. Therefore, there are 5 mV in this pool who have the message Error (Missing). All attempts to eliminate the pool or the VMs do not work. Ive tried the SVIClone command without success (although it said that it completed successfully). This occurred after only a bad call. When recomposition, I can't not done properly and some of my virtual machines have been removed from the VC but kept in admin view. Now, I can't get rid of them.

  C. in this sense, can someone please confirm that these are appropriate measures to recompose the pools for updates/hotfixes:

  1. ask to master model of loan. Make sure that VM is off.  (Decline of the area or to keep it on the field when taking snapshots and creating LC pool?)

  2. create the snapshot of the model

  3. follow the wizard in view and instant install Linked Clone pool - first selection

  4 replica is created and child VM appear in function image parent

  To redial:

  1. create the second snapshot with parent amended template

  2. in the Admin view, crop, and select new snapshot

  3 recompose

  4 remove the first snapshot and keep only the second.

  When recomposition, the names of DNS, the domain of the virtual machine is turned on, rights, all should remain the same and no affected correct? All applications (ex: Outlook) should stay with the game of profile information?

  Thanks for any assistance,

  r.

  Here are the instructions for connecting to ADAM

  • Connect to the computer hosting your VMware View connection server through VMware Infrastructure Client or Microsoft RDP.
  • Open the ADAM Active Directory Service Interfaces Editor.
  • In a Windows Server 2003, click Start > programs > ADAM > ADAM ADSI Edit.
  • In a Windows Server 2008, click Start > all programs > administrative tools > ADSI Edit.
  • Right-click ADAM ADSI Edit , and then click on connect to.
  • Verify that Select or type a domain or server is selected, and the destination points to localhost.
  • Select the distinguished name (DN) or naming context , and then type dc = vdi, vmware, dc = int = dc.

  As far as questions of fact composer composer account have the correct permissions to AD.   Did you look in the logs of composer within the guest to see if you can get all the information from there?

• Nican.dll call python questions

  Hi all

  I have a feeling that this issue will be left without an answer, but I'll ask anyway.

  For a project, I need to use Python2.7 to receive frames from a bus.  What I have to do is monitor CAN all traffic on the bus, I have to send frames.  I searched (and searched and searched) for some sort of solution to this, but have found none.  Here's the code I have so far:

  Test #CAN using Python

  types import *.
  import table *.

  #Load DLL
  CANdll = cdll. LoadLibrary ("NICAN.dll")

  canName = c_char_p ("CAN0")
  canNumAttr = c_ulong (8)

  # Define constants
  NC_TRUE = c_ulong (1)
  NC_TRUE = c_ulong (0)
  NC_CAN_MASK_STD_DONTCARE = c_ulong (0x00000000)
  NC_CAN_MASK_XTD_DONTCARE = c_ulong (0x00000000)

  # The values taken from nican.h
  #NC_ATTR_BAUD_RATE = c_ulong (0 x 80000007)
  #NC_ATTR_START_ON_OPEN = c_ulong (0 x 80000006)
  #NC_ATTR_READ_Q_LEN = c_ulong (0 x 80000013)
  #NC_ATTR_WRITE_Q_LEN = c_ulong (0 x 80000014)
  #NC_ATTR_CAN_COMP_STD = c_ulong (0 x 80010001)
  #NC_ATTR_CAN_MASK_STD = c_ulong (0 x 80010002)
  #NC_ATTR_CAN_COMP_XTD = c_ulong (0 x 80010003)
  #NC_ATTR_CAN_MASK_XTD = c_ulong (0 x 80010004)

  # instantiate the table a
  canAttrIdList = (c_ulong * 8))

  # Fill the values in the table
  canAttrIdList [0] = c_ulong (0 x 80000007)
  canAttrIdList [1] = c_ulong (0 x 80000006)
  canAttrIdList [2] = c_ulong (0 x 80000013)
  canAttrIdList [3] = c_ulong (0 x 80000014)
  canAttrIdList [4] = c_ulong (0 x 80010001)
  canAttrIdList [5] = c_ulong (0 x 80010002)
  canAttrIdList [6] = c_ulong (0 x 80010003)
  canAttrIdList [7] = c_ulong (0 x 80010004)

  #NC_ATTR_BAUD_RATE = 500000
  #NC_ATTR_START_ON_OPEN = NC_TRUE
  #NC_ATTR_READ_Q_LEN = 100
  #NC_ATTR_WRITE_Q_LEN = 0
  #NC_ATTR_CAN_COMP_STD = 0
  #NC_ATTR_CAN_MASK_STD = NC_CAN_MASK_STD_DONTCARE
  #NC_ATTR_CAN_COMP_XTD = 0
  #NC_ATTR_CAN_MASK_XTD = NC_CAN_MASK_XTD_DONTCARE

  # instantiate table a
  canAttrValueList = (c_ulong * 8)

  # Fill the values in the table
  canAttrValueList [0] = 500000
  canAttrValueList [1] = NC_TRUE
  canAttrValueList [2] = 100
  canAttrValueList [3] = 0
  canAttrValueList [4] = 0
  canAttrValueList [5] = NC_CAN_MASK_STD_DONTCARE
  canAttrValueList [6] = 0
  canAttrValueList [7] = NC_CAN_MASK_XTD_DONTCARE

  returnValue = CANdll.ncConfig (canNumAttr, canAttrIdList, canName, canAttrValueList)

  CODE ##END

  Which causes this error:

  Traceback (most recent call changed):
  File "C:\Users\Chadwick\Dropbox\Senior Project\CAN\NI-CAN\ITB CAN\test.py", line 63, in
  returnValue = CANdll.ncConfig (canNumAttr, canAttrIdList, canName, canAttrValueList)
  ValueError: Procedure called with not enough arguments (missing 16 bytes) or bad calling convention

  It seems that I am not calling the function correctly.

  Yes, I understand that nor is not supported by the Python.  However, any help with this is appreciated.

  Thank you

  He is the labour code.  I question the material for how many images of waiting there, then read them individually as I'm having no luck using ncReadMult.  If someone needs to do this, here's a starting point.

  /thread

  types import *.
  import table *.
  import sys
  import of struct
  time of import

  #Load DLL
  CANdll = windll. LoadLibrary ("NICAN.dll")

  NC_ST_READ_AVAIL = c_ulong (0x00000001)
  NC_ATTR_READ_PENDING = c_ulong (0 x 80000011)

  # HEADER INFORMATION RELEVANT C
  # typedef NCTYPE_INT32 NCTYPE_STATUS;
  # typedef NCTYPE_UINT32 NCTYPE_OBJH;

  ##typedef struct {}
  # NCTYPE_ABS_TIME Timestamp;
  # NCTYPE_CAN_ARBID ArbitrationId;
  # FrameType NCTYPE_UINT8;
  # NCTYPE_UINT8 DataLength;
  # NCTYPE_UINT8 data [8];
  #} NCTYPE_CAN_STRUCT;

  class CAN_STRUCT (Structure):
  _fields_ = [("Timestamp", c_ulonglong),
  ("ArbitrationId", c_ulong);
  ("Frames", c_ubyte);
  ('DataLength', c_ubyte);
  («Données», c_ubyte * 8)]

  CAN_receive_buffer = (CAN_STRUCT * 1000))

  Status = c_long (0)
  CAN_HANDLE = c_ulong (0)
  #CAN_data_size = c_ulong (sys.getsizeof (CAN_receive_buffer))
  CAN_data_size = c_ulong (17600)

  CAN_received_size = c_ulong (1)
  CAN_NAME = c_char_p ("CAN0")
  canNumAttr = c_ulong (8)

  # Define constants
  NC_TRUE = c_ulong (1)
  NC_FALSE = c_ulong (0)
  NC_CAN_MASK_STD_DONTCARE = c_ulong (0x00000000)
  NC_CAN_MASK_XTD_DONTCARE = c_ulong (0x00000000)

  # The values taken from nican.h
  #NC_ATTR_BAUD_RATE = c_ulong (0 x 80000007)
  #NC_ATTR_START_ON_OPEN = c_ulong (0 x 80000006)
  #NC_ATTR_READ_Q_LEN = c_ulong (0 x 80000013)
  #NC_ATTR_WRITE_Q_LEN = c_ulong (0 x 80000014)
  #NC_ATTR_CAN_COMP_STD = c_ulong (0 x 80010001)
  #NC_ATTR_CAN_MASK_STD = c_ulong (0 x 80010002)
  #NC_ATTR_CAN_COMP_XTD = c_ulong (0 x 80010003)
  #NC_ATTR_CAN_MASK_XTD = c_ulong (0 x 80010004)
  #NC_ATTR_LISTEN_ONLY 0 X 80010010

  # instantiate the table a
  canAttrIdList = (c_ulong * 9))

  # Fill the values in the table
  canAttrIdList [0] = c_ulong (0 x 80000007)
  canAttrIdList [1] = c_ulong (0 x 80000006)
  canAttrIdList [2] = c_ulong (0 x 80000013)
  canAttrIdList [3] = c_ulong (0 x 80000014)
  canAttrIdList [4] = c_ulong (0 x 80010001)
  canAttrIdList [5] = c_ulong (0 x 80010002)
  canAttrIdList [6] = c_ulong (0 x 80010003)
  canAttrIdList [7] = c_ulong (0 x 80010004)
  canAttrIdList [8] = c_ulong (0 x 80010010)

  #NC_ATTR_BAUD_RATE = 500000
  #NC_ATTR_LISTEN_ONLY = NC_TRUE
  #NC_ATTR_READ_Q_LEN = 100
  #NC_ATTR_WRITE_Q_LEN = 0
  #NC_ATTR_CAN_COMP_STD = 0
  #NC_ATTR_CAN_MASK_STD = NC_CAN_MASK_STD_DONTCARE
  #NC_ATTR_CAN_COMP_XTD = 0
  #NC_ATTR_CAN_MASK_XTD = NC_CAN_MASK_XTD_DONTCARE

  # instantiate table a
  canAttrValueList = (c_ulong * 9)

  # Fill the values in the table
  canAttrValueList [0] = 500000
  canAttrValueList [1] = NC_TRUE
  canAttrValueList [2] = 100
  canAttrValueList [3] = 0
  canAttrValueList [4] = 0
  canAttrValueList [5] = NC_CAN_MASK_STD_DONTCARE
  canAttrValueList [6] = 0
  canAttrValueList [7] = NC_CAN_MASK_XTD_DONTCARE
  canAttrValueList [8] = NC_FALSE

  # Configure the equipment CAN
  Status = CANdll.ncConfig (canNumAttr, canAttrIdList, CAN_NAME, canAttrValueList)
  If Status! = 0 :
  "Printing on"ncConfig"error
  Status of printing

  Status = CANdll.ncOpenObject (CAN_NAME, byref (CAN_HANDLE))
  If Status! = 0 :
  "Printing on"ncOpenObject"error
  Status of printing
  impression CAN_HANDLE.value

  Time.Sleep (1)

  Try:
  Status = CANdll.ncAction (CAN_HANDLE, c_ulong(0x80000001), 0)
  If Status! = 0 :
  "Printing on"ncAction:start"error
  Status of printing
  impression CAN_HANDLE.value

  I have = 0
  ##string = "" data: "".
  String = «»

  pending_CAN_frames = c_ulong (0)
  while I<>
  Status = CANdll.ncGetAttribute (CAN_HANDLE, NC_ATTR_READ_PENDING,
  32, byref (pending_CAN_frames))
  Print "waiting for frames: %d" % pending_CAN_frames.value
  If Status! = 0 :
  "Printing on"ncGetAttribute"error
  Status of printing
  for n in range (0, pending_CAN_frames.value):
  Status = CANdll.ncRead (CAN_HANDLE, CAN_data_size,
  ByRef (CAN_receive_buffer [n]))
  for n in range(0,pending_CAN_frames.value):
  for j in range (0, CAN_receive_buffer [n]. DataLength):
  String = string + '%x' % (CAN_receive_buffer [n]. Data [j])
  print '% X\t%d\t%s' % (CAN_receive_buffer [n]. ArbitrationId, CAN_receive_buffer [n]. DataLength, string)
  String = ' ' #reset chain
           
  I += 1

  # ALWAYS CALL LAST
  Finally:
  Status = CANdll.ncCloseObject (CAN_HANDLE)
  If Status! = 0 :
  "Printing on"ncCloseObject"error
  Status of printing

  /thread

  I hope this helps someone in the future.

• pass fails with a missing resource pool alert

  Hi, I have a server dell power edge r510, with ESXi 5.0 is installed in it.

  in one of the virtual machines within this server, I installed Vcenter (I think that it is Version 5.1) everything was stable until the vcenter database gets 10 GB and crashed and I couldn't fix it. So I installed a new windows with vcenter 5.5 inside vps. and for this new vcenter reconnected to the server. so, I've reconfigured resource pools and VPS users again in this new vcenter.

  Watch ESXi host now as does not not to the vcenter. but all virtual machines inside the esxi server work without problems.  I can't reconnect to the host in vcenter, and I can't connect directly to the ESXi via vsphere client and root password.

  but I can log on to the esxi via ssh or console.

  from the console, I restarted the management services, but it does not help.

  the SSH, I ran the following commands:

  status /etc/init.d/vpxa #.

  vpxa is running

  status /etc/init.d/hostd #.

  pass is not running.

  When I restart pass, it is said has started, but after a few minutes still pass fails.

  l # /etc/init.d/hostd restart

  Watchdog - pass: PID of the file/var/run/vmware/watchdog-hostd. PID does not exist

  Watchdog - pass: impossible to end guard dog: no monitoring running processes to pass

  SH: you must specify which kill

  [421281] Begin ' pass ++ min = 0, swap, group = pass etc/vmware/hostd/config.xml', min-uptime = 60, max-fast-failures = 1, max-total-failures = 1000000, bg_pid_file = "

  pass began.

  **********************************************************

  status /etc/init.d/hostd #.

  pass is running.

  ***************************************************************

  but I can't use all the controls of esxcli.

  List of the allowedip of esxcli network firewall ruleset

  Connect to locahost failed: connection failure

  ************************************************************

  status /etc/init.d/hostd #.

  pass is not running.

  ***************************************************************

  I searched the problem on localhost, Ko, said check the CPU usage is below 90%, which is good in my esxtop, then says check network ports and pings, they were right, too, said to check/etc/hosts to 127.0.0.1 localhost entry and checking /etc/resolv.conf and they were right too. as I can ping localhost and localhost nslookup returns 127.0.0.1

  then I started reading the server logs and found this error output of vm-support: hostd.log

  [cntos58-64-Farzin - 105.vmx'] could not get the parameters of resource for a virtual machine under tension

  Award of the VM ' / vmfs/volumes/.../cntos58-64-Farzin-105.vmx' to the root resource pool - configured pool 'pool11' does not exist

  SysInfo error on return operation State: verification of Admission of cpu resource failure. See the VMkernel detailed error information log

  cntos58-64-Farzin - 105.vmx: vim.fault.InsufficientCpuResourcesFault

  *************************************************************************

  How can I change the list of resources of the VM to ssh when esxcli do not work?

  I am facing this problem recently, almost all the 5 days the server will respond is not in vcenter, restart the entire esxi server can solve the problem but it apears again.

  I think that resource in vcenter pools doesn't sync properly with the configuration of esxi, as when I connect to the server directly with root/vshpere it shows different configuration than what I see in vcenter!

  and I can't upgrade esxi host because there are about 10 VPSes important and stable running on this server which is my main server and I can not have time on this server or migrate virtual machines to a different server/IPs.

  because I'm not sure of the compatibility of the versions of drivers/bios nic with ESXi 5.5 and I fear that if I update the ESXi from 5.0 to 5.5 I face other questions strangers/downtime.

  I had the server up and running again, by editing this file: /etc/vmware/hostd/pools.xml

  then I found the VPS with id of the pool of resources 11 evil, changed for another pool of resources as the other virtual machines.

  2014 07-29 T 08: 38:52.64965Z

  2

  pool366

  and then made a

  restart the /etc/init.d/hostd

  all started working again without restarting the whole esxi server and turn off virtual machines, I have searched for about 1 day to solve this simple thing!

  even once when I made a few changes in the vcenter, and then restarted resource pool settings move it in ssh, it fails under vcenter changed the VM resource for a bad configuration pool.

  so I changed the resource pool manually xml and restarted spend, while vcenter can connect to the esxi host.

  then vcenter, again removed all the resource pools and created new resource pools. and this question of time is set.

  There was some resource pool configuration that was imported from esxi host to vcenter which was no longer available and has not been deleted in syncronizations between esxi and vcenter when changed resource pools. and the list of the missing resources caused problems.

• I recently downloaded Firfox 4, which is constantly freezing up. What is going on, nothing has changed on my end.

  I am constantly "script does not" invite and even if I cancel the script, Firefox remains frozen/insensitive, and even if I try to restart it takes a lot of time! What happened to middle (gmail) emails, navigate to a web page on a business... to bad call timed times. I have not changed anything on my end. If I can't get this fixed, I'll have to go back to the Explorer? Ugh! Please help me... Is there a way to return to an earlier version of Firefox when I didn't have this problem? Thank you.

  If you do not want to go back to 3.6. * You can get Firefox at http://www.mozilla.com/en-US/firefox/all-older.html 3.6.16

  Please don't get Firefox on sites like filehippo oldapps or such when there is no need of any version.

• Update the RN204 OS 6.6; Update of plex 1.2.2.2857 fails to start with "empty resource error."

  Since the last firmware update to 6.6 on my RN204, the plex 1.2.2.2857 server application version does not work. After installation, when I click on the button 'On', I get the following error: initialization failed: empty resource error. NML bad Call.

  Looked at several threads on Netgear and Plex. Can't find the solution. My plex server is dead!

  Please see https://community.netgear.com/t5/Current-NETGEAR-and-Partners/Problems-running-Plex-Media-Server-aft...

  By restarting your NAS and a handful of minutes waiting should cause the problem to be solved.

• Couch Potato server by Mhynio 3.0.1.

  Program will not start on 10 Windows and OS 6.5.0

  Error message

  Resource error is empty. Bad call NML

  Code: 22002010000

  Help please!

  p.s. I can mess with SSH

  Forget the above post it please

  Just tried a re - install using firmware update instead of download App and my installation is back...

  Is the above a bug in 6.5.0?

• Upgrade to 6.6.0 on RN214

  I just upgraded to 6.6.0

  Now, I find that Plex has an error

  "Application failed to initialize".

  EmPy resource error. Bad call NML.

  Everything was fine before the upgrade. ?

  I have the last plex.

  Please see https://community.netgear.com/t5/Current-NETGEAR-and-Partners/Problems-running-Plex-Media-Server-aft...

  By restarting your NAS and a handful of minutes waiting should cause the problem to be solved.