Bad connection with List_Item?'

Similar Questions

• Troubleshoot the bad connection with router (WRT350N) and Point (WAP4400N) wireless access

  Hi all

  I have a problem and will apprecaite all the help I can get. I think I will find an answer here.

  I have a small network, Linksys WRT350N (wireless router) attached to a modem and then connected to a desktop computer and with 3 wireless laptops connected to the router. All 3 are really great to work and access the internet very well.

  Currently, I have the need to expand the network to 3 floors, so I bought 3 Points of access wireless of Linksys (WAP4400N).

  I ran 3 cables CAT5e cable from the router and which ends individually all 3 floors, the top floor is less than the router 40meters. With the cables that came in their boxes, I connected the APs to the router and I have correctly set up the 3 Access Points with them attached to the router, all 3 works perfectly (I can access wireless internet via 3-point). However when I take the points of access to the upper floors and connect cables cat5e APs no longer work but connect after some time with the message "limited connectivity".

  Why can I connect when the APs are connected to the ground floor via a short cable that came in the box and not when it is connected to put cables from the ground floor to the upper floors but rather make the "LIMITED SERVICE" message and cannot connect to the internet.

  Also if I connect the cat5e cables directly to a laptop computer on all the floors, I can connect to the internet (the work of cables fine when connected directly to a laptop computer), but when it is connected to the connection of the APs has failed and I begin to see strange IP addresses from the APs.

  Oh, one more piece of important information: when I connect cables CAT5e cable on all floors direct to a laptop I can connect to the internet (the work of cables very well when it is connected directly to a laptop) but when connected to the failed to connect APs and I begin to see strange IP addresses from the APs.

  HEPL!

  I think I have the forum a status report on my post. As I mentioned in my last post, the problem has been as a result of lower cable at my provider. The network is running smoothly. Has been in place since last week when I replaced the lower quality cat5e cable cat5e cable.

  A Board here please be careful and make sure you complete the cable. A bad end can lead to connection problems I discovered in this case when my team confidence terminated cable incorrectly.

  Network up to & operational: Linksys WRT350N router without wire + 3 Linksys Wireless Access Points WAP4400N + Modem providing access to (1 computer (cable), 6 workstations (wireless), & 5 laptops (wireless).) Network to grow shortly.

  Thanks to everyone who helped make this project a reality.

• Bad connection with charger

  I don't know how it happened, but I think that it is after I accidentally slept on it. Although it either in this topic will only show 50% battery level unless I have to apply pressure on the back. I also spend autour charger wire to get the phone for free and what load will show battery level OK. If I hit it slightly, it turns off charge and requires a lot of scope to put on the. While he's dead and I have thye charger connected, it will show the battery especially with 1 bar of red at the bottom with the symbol but load does not load. Again, I must move the thread so that it can start loading in which case would begin to turn it on and then show the battery level. I know this is similar to other subjects but Iran were all singular and I combined problems, which means that I need an another solution to fix this cannot so somebody tell me what happened and how to fix it please.

  Issue edited by Rickard

  @malakhi

  That is not factory reset the phone

  malakhi wrote:
  Try the reset factory and turning the phone off and charge your phone when is disabled. Then fully charged switch on and feedback

  @HaosLeonidas

  This seems to be a hardware problem, contact your Local support for your device inspected

• Tecra Z50-A-14 t - bad connection WiFi signal

  In short.

  Absolutely the same problem with my new Tecra.
  Stable connection by cable.

  Bad connection same 3 5 meters from the router. If the distance is longer, or I use the laptop in another room sometimes it s no link at all.
  The card is Intel (R) Dual Band Wireless AC-3160 and that article how I found the link above.

  All electronic in the work of the House with no problem, but this piece of garbage to Wi - Fi only the same has even after 3 visits in the repair shop. And that s for new out of the box laptop.

  I really disappointed me.

  + The message was edited: link has been removed - forum rules +.

  Hmm. have you noticed the same problem of weak signal using the laptop to the power of the battery as well as connected to the adapter?

  My signal low similar knowledge questions may seem due BOF WiFi enabled power saving settings. This setting can be found in the current power plant? Advanced settings

  On the other hand, it might be possible that there is something wrong with the WiFi antenna cable. Maybe it is not properly connected to the mini PCI module

  In the case of changing the settings would not help you and if your already updated the Wlan to the latest version available, I think that the Toshiba certified maintainer should check the antenna.

• Bad experience with Lenovo.

  Hello world

  I would like to share with you my bad experience with lenovo. I bought S10 2 weeks. Since the first day, it has not worked right. In the middle of my work it rebooted by itself and took a lot of time (20-30 min) to open XP when I turned it on. Then, I decided to restore the system with the OneKey Recovery button, but I couldn't activate the laptop after that at all. After that, I called technical support and explain my problem. They advised me to call lenovo sales and ask to replace the system. I followed the advice and call them and the representative told me that I have to send the laptop to the technical support group and they try first to solve this problem, if they would not be able to fix then I would send a new, and it would take at least 2 weeks to understand what is wrong with the system. I was indignant at this topic and he told me that if I want a new right now that I have to pay 15% bonus. Can you imagine that? Then I called the technical support group and we did some tests together and it did not work. After that, they still suggest to call lenovo sales to replace this laptop. Finally, sales representative decided to replace my laptop faulty by a new one. He arranged the pick UPS faulty laptop and created the order for the new system. Later the same day, I found that they charged me twice for the laptop. This means that I have a defective S10 only laptop, but have paid in full for two laptops. Today is the second day, and nobody came to the inverter to take the defective laptop. I called them and I was wondering why no one pick up the laptop. The answer was: no one does not organize the UPS pick up. This is Lenovo service! I've never seen this kind of service. It's terrible! I asked to connect with the Manager, but the Manager was very busy and I left the request to remember. I lose 4-5 hours of my time to explain my problem and request a replacement. Whenever they transferred my call to various departments, I had to wait 20-25 min. technical support is very good, they are very helpful and polite. Unfortunately, I can't say the same for lenovo sales representatives. It was my first lenovo and I'm sure that the last of them. Would not recommend to anyone to buy it. The service is horrible!

  I hope that, ultimately, the faulty laptop is picked up tomorrow. I am thinking to return it and get my money back if they don't send me not the new Friday, as they promised.

  Thanks for sharing your experience here!

  I received my S10 new and very satisfied. This works perfectly. Finally, I got what I wanted.

  I did from my first experience with Lenovo: If you have a problem with Lenovo products you should call and talk with officials. It is best to talk with several representatives, because not every representative has correct information. If the representatives are not useful, you have to speak to the supervisor or Manager. In addition, post your case in this forum. I suspect that some manager Lenovo check this forum. My problem has been resolved as soon as I posted my experience here.

  The IBM product portable grand, but I wish they hire more agents for sale or magazine somehow their service.

  Marry Christmas

• bad connect to Sql * more via command and cannot log on to the designer (need for connection string)

  I installed Oracle Developer with success, but having bad connect to Sql more than command line, also unable to connect via the developer tools, I get a TNS: Connect timeout occurred. This happens also for the "Plus" Sql for Windows.

  

  
  

  However, I can connect via the Sql Plus command window when it is executed from "Start-> all programs", but not when I first run the command window:

  

  
  

  I have a good Oracle 11 g install on Windows 7 and a good developer Sql install so I can connect to databases, but something does not work when you try to connect through these tools. Although Sql Plus works when called from 'Start-> all programs'
  

  sqlplus scott/tiger - don't use SQL * Net, you can connect like this even with the listener is stopped.

  Developer SQL can ONLY connect using SQL * Net & can be blocked by the firewall

  to connect using sqlplus & SQL * Net, you need to invoke it as below

  sqlplus scott/tiger@orcl

• INSTEAD, error PLS-00049: bad connection variable

  I try to use a PLACE for me to enter data in a table of bridge. Thanks in advance
  
  I get the following error:
  
  Error on line 4: PLS 00049: bad connection variable ' NEW. MEMBER_ID'
  
  2 INSTEAD OF THE INSERT OR UPDATE OR DELETE
  3 ON VI_Member_Talent_VW making REFERENCE AGAIN AS NINE OLD and OLD
  4. FOR EACH LINE
  5. START TO
  6. IF THE INSERTION
  
  Here is the code:
  
  
  
  CREATE OR REPLACE TRIGGER VI_INSERT_UPDATE_MT
  INSTEAD OF INSERT OR UPDATE OR DELETE
  ON VI_Member_Talent_VW REFERENCING NEW AS NEW as OLD OLD
  FOR EACH LINE
  BEGIN
  IF THE INSERTION
  THEN
  INSERT INTO VI_Member_Talent (Member_ID, Talent_ID) VALUES (: NEW.) Member_ID,: NEW. Talent_ID);
  END IF;
  IF THE UPDATE
  THEN
  UPDATE VI_Member_Talent SET Member_ID =: NEW. Member_ID, Talent_ID =: NEW. Talent_ID
  WHERE ROWID =: OLD.ID;
  END IF;
  IF THE REMOVAL
  THEN
  DELETE FROM VI_Member_Talent WHERE ROWID =: OLD.ID;
  END IF;
  END;
  
  Edited by: user13003575 may 2, 2010 08:53

  user13003575 wrote:
  It's the view

  CREATE OR REPLACE FORCE VIEW  "VI_MEMBER_TALENT_VW" ("ID", "Member_ID", "Talent_ID") AS
  SELECT rowid id, Member_ID, Talent_ID
  FROM VI_Member_Talent
  /
  

  and there is the problem.

  The view was created with quotes around column names, so that they are case-sensitive. You need to either modify your trigger double quote column names, or rebuild the view without the quotes. Personally, I'd go with changing the display.

  John

• Bad connection variable

  Hi friend
  
  I don't want to use a trigger to update a value of varchar2:
  
  create or replace trigger WORK_STITCH_NAME_TRIG
  after insert or update on ASS_WORK_STITCH
  for each line
  declare
  NAME VARCHAR2 (100);
  Start
  If the insertion
  Select ENAME in the NAME of UAMRIS. WORDER where OID =: new. OID;
  Update UAMRIS. WORDER
  Set ENAME =(:new.NAME)
  where OID =: new. OID;
  end if;
  end;
  /
  
  but it gives me error like ': New.Name' variable of bad connection.
  
  Can someone help me with this please!
  
  Thank you
  
  Zitouni

  : OLD /: NEW applies only to the trigger of the columns of the table. Your relaxation is on table WORK_STITCH and the NAME is variable PL/SQL. Simply remove: NEW:

  create or replace trigger WORK_STITCH_NAME_TRIG
  after insert or update on ***_WORK_STITCH
  for each row
  declare
  NAME VARCHAR2(100);
  begin
  if inserting then
  select ENAME into NAME from UAMRIS.WORDER where OID=:new.OID;
  update UAMRIS.WORDER
  set ENAME=NAME
  where OID=:new.OID;
  end if;
  end ;
  /
  

  SY.

• I just bought the last Apple TV - I can't seem to connect with the App Store and Siri is completely useless. This is an example of how Apple is unable to produce a useful product?

  I just bought the last Apple TV - I can't seem to connect with the App Store and Siri is completely useless. This is an example of how Apple is unable to produce a useful product?

  Hello

  Be sure to follow the instructions in this article to support > set up your Apple TV (4th generation) - Apple supported

• Current device is registered with the former owners of Apple ID, not allow me to connect with my Apple ID?

  Current device is registered with the former owners of Apple ID, not allow me to connect with my Apple ID?

  The former owner must unlock with their password, or give you the password. Otherwise, the phone doesn't help you and no one can help you. Get your money back if you can.

  What to do before you sell or give away your iPhone, iPad or iPod touch - Apple Support

• Loss of connection with iCloud

  Whenever I login I have to re - connect with my iCloud - suggestions, no matter who?

  I assume you mean iCloud.com website?  How are you internet connection otherwise?

• Mac book air cannot detect my iPhone 6, after the cable on my I phone 6 to connect with my mac book air, nothing appear on the mac book. Seems like it can't detect the file i phone 6. I want to export my photos and do the upgrade version.

  Hi, after plug the cable on my phone i 6 to connect with my mac book air, nothing appear on the mac book.

  Seems like it can't detect the file i phone 6. I want to export my photos and do the upgrade version.

  Current situation is nothing exportable phone and also cannot do anything mac book because they cannot detect each other. Please advise, thank you.

  You can try to move to a different USB port. And if your just trying to swap photos try Airdrop. Also try to go here If iTunes does not your iPad, iPhone or iPod - Apple SupportHope this help, good luck to you.

• In a roaming network, Mac always connects with AE which is further away

  So, I had a roaming network for years to host a detached office which was too far from my house.  Worked very well.  Now, my family and I have moved into a temporary rented condo (two floors).  Therefore, there is a lot of wifi networks in the area in conflict with.

  After trying to extend the network (signal too low in the area), I decided to try the roaming network again.  Most of the time, it works very well.  But from time to time, my iMac (on the ground floor) connects with the Airport Extreme, which is on the floor instead of the Airport Express, which is down in the same room as the iMac.  What happens when it connects to the Airport Extreme on the floor, my Tx rate drops to less than 100 Mbps (sometimes dramatically if) and I am unable to listen to the music to my Airport Express without dropouts.

  The dressing was to turn off my wifi on the iMac, and then turn it back on.  It will then connect to the Airport Express.   The problem is that I have to do this in general once a day as my iMac will enter into the "standby" and periodically reconnect with Airport Extreme when I wake up (or if I re-enable it if off).  Ideally, he would stay with the Airport Express.

  So I hope that there is an alternative.  I thought about simply renaming the Airport Express network in the different name of Airport Extreme.  But all the itinerant instructions whereby I know that network names must be the same for all airports in the roaming network.  But perhaps this is not the case.

  Comments are appreciated!

  Unfortunately, you encounter a known issue with the use of a roaming network... and it is not specific to those provided by Apple either. The "solution" you use, although not elegant, is basically everything with that we have (at this time) to go.

  In theory, your iMac fixed, must always connect to the Wi - Fi with the signal network hard... not necessarily the closest to it. It may be possible, since you mentioned that you live in a highly congested environment Wi - Fi, your iMac is struggling to determine the right network to connect to when starting.

  Of course, a more "permanent" solution for your iMac, at least, would connect directly to the nearest base by Ethernet station.

• Thunderbird does not connect with the server

  Another recent problem is Thunderbird does not connect with the server. I don't know if sent mail will go out, but I know I'm nothing receive. My internet connection works well for FF or another browser. I checked my settings and they seem OK. I checked the default settings in Win10x64 and they are correct. Any ideas?

  Although windows 10 is new for us all. How do solve you. I have other solution with very similar issues.

• Does not connect with the e-mail server after update.

  Thunderbird ran an auto update yesterday. Then it just stopped working. It does not connect with the Comcast email server. An error message appears "Unable to connect" and "the connection was refused when attempting to contact live.mozilla.messaging.com. I don't want to uninstall and reinstall for fear of losing my emails and address book. How can we get Thunderbird set, there is no tool in the toolbar to enable the debugging and correction of program errors.

  I use Thunderbird version 38.1.0.

  Thank you.

  The problem solved itself, Thunderbird has just started working. I followed the thread suggested by Christ1 and found none of it applied. No malware, no browser, no certificate error security block. I did, however, in Thunderbird, under Tools/Options/General uncheck the button for "When Thunderbird launches, show the Start Page in the message box." I do know that if this helped, Thunderbird still do not access Comcast mail for hours after that, even with several stops and restarts.

  Until the next problem...