Bad connection with charger

Similar Questions

• Troubleshoot the bad connection with router (WRT350N) and Point (WAP4400N) wireless access

  Hi all

  I have a problem and will apprecaite all the help I can get. I think I will find an answer here.

  I have a small network, Linksys WRT350N (wireless router) attached to a modem and then connected to a desktop computer and with 3 wireless laptops connected to the router. All 3 are really great to work and access the internet very well.

  Currently, I have the need to expand the network to 3 floors, so I bought 3 Points of access wireless of Linksys (WAP4400N).

  I ran 3 cables CAT5e cable from the router and which ends individually all 3 floors, the top floor is less than the router 40meters. With the cables that came in their boxes, I connected the APs to the router and I have correctly set up the 3 Access Points with them attached to the router, all 3 works perfectly (I can access wireless internet via 3-point). However when I take the points of access to the upper floors and connect cables cat5e APs no longer work but connect after some time with the message "limited connectivity".

  Why can I connect when the APs are connected to the ground floor via a short cable that came in the box and not when it is connected to put cables from the ground floor to the upper floors but rather make the "LIMITED SERVICE" message and cannot connect to the internet.

  Also if I connect the cat5e cables directly to a laptop computer on all the floors, I can connect to the internet (the work of cables fine when connected directly to a laptop computer), but when it is connected to the connection of the APs has failed and I begin to see strange IP addresses from the APs.

  Oh, one more piece of important information: when I connect cables CAT5e cable on all floors direct to a laptop I can connect to the internet (the work of cables very well when it is connected directly to a laptop) but when connected to the failed to connect APs and I begin to see strange IP addresses from the APs.

  HEPL!

  I think I have the forum a status report on my post. As I mentioned in my last post, the problem has been as a result of lower cable at my provider. The network is running smoothly. Has been in place since last week when I replaced the lower quality cat5e cable cat5e cable.

  A Board here please be careful and make sure you complete the cable. A bad end can lead to connection problems I discovered in this case when my team confidence terminated cable incorrectly.

  Network up to & operational: Linksys WRT350N router without wire + 3 Linksys Wireless Access Points WAP4400N + Modem providing access to (1 computer (cable), 6 workstations (wireless), & 5 laptops (wireless).) Network to grow shortly.

  Thanks to everyone who helped make this project a reality.

• Bad connection with List_Item?'

  Hi all
  I use Oracle 10 g and I write this code in a Menu:

      Customer_Id NUMBER(10) := :LIST_ITEM_CUSTOMERS;

  LIST_ITEM_CUSTOMERS corresponding to NUMBER data Type
  
  So, I got this error:

   Bad bind variable 'LIST_ITEM_CUSTOMERS'?
  
  
  
  Thanks in advance :)                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    

  You can't get directly the content of an element of forms when you are outside (menu or pll). Use the built-in Name_in() function:

  var := Name_in('LIST_ITEM_CUSTOMERS');
  

  François

• Started at Mo and not charging with the charger connected. Charger works. Keyboard not workin except power button / stop. Restarted using ex in car without success. SW

  Started MacBook and not charging with the charger connected. Charger works. Keyboard does not not except the power button / stop. Restarted ex drive no available help hoping that it was a matter of SW. SW and the operating system works very well. Read some info online. Tried to reset the SMC. Now, the MacBook does not start. Can U help me please. Thanks in advance.

  MacBook, 2010, Mac OS X 10.6.8

  Hi Veronica Steward,.

  I understand that you have turned into a series of questions about your MacBook and want help getting the computer to turn on. Here is an article that can help you through the steps to fix this problem:
  

  If your Mac will not turn on - Apple Support

  Let us know how it goes and thanks for coming to Apple Support communities.

  See you soon.

• Bad experience with Lenovo.

  Hello world

  I would like to share with you my bad experience with lenovo. I bought S10 2 weeks. Since the first day, it has not worked right. In the middle of my work it rebooted by itself and took a lot of time (20-30 min) to open XP when I turned it on. Then, I decided to restore the system with the OneKey Recovery button, but I couldn't activate the laptop after that at all. After that, I called technical support and explain my problem. They advised me to call lenovo sales and ask to replace the system. I followed the advice and call them and the representative told me that I have to send the laptop to the technical support group and they try first to solve this problem, if they would not be able to fix then I would send a new, and it would take at least 2 weeks to understand what is wrong with the system. I was indignant at this topic and he told me that if I want a new right now that I have to pay 15% bonus. Can you imagine that? Then I called the technical support group and we did some tests together and it did not work. After that, they still suggest to call lenovo sales to replace this laptop. Finally, sales representative decided to replace my laptop faulty by a new one. He arranged the pick UPS faulty laptop and created the order for the new system. Later the same day, I found that they charged me twice for the laptop. This means that I have a defective S10 only laptop, but have paid in full for two laptops. Today is the second day, and nobody came to the inverter to take the defective laptop. I called them and I was wondering why no one pick up the laptop. The answer was: no one does not organize the UPS pick up. This is Lenovo service! I've never seen this kind of service. It's terrible! I asked to connect with the Manager, but the Manager was very busy and I left the request to remember. I lose 4-5 hours of my time to explain my problem and request a replacement. Whenever they transferred my call to various departments, I had to wait 20-25 min. technical support is very good, they are very helpful and polite. Unfortunately, I can't say the same for lenovo sales representatives. It was my first lenovo and I'm sure that the last of them. Would not recommend to anyone to buy it. The service is horrible!

  I hope that, ultimately, the faulty laptop is picked up tomorrow. I am thinking to return it and get my money back if they don't send me not the new Friday, as they promised.

  Thanks for sharing your experience here!

  I received my S10 new and very satisfied. This works perfectly. Finally, I got what I wanted.

  I did from my first experience with Lenovo: If you have a problem with Lenovo products you should call and talk with officials. It is best to talk with several representatives, because not every representative has correct information. If the representatives are not useful, you have to speak to the supervisor or Manager. In addition, post your case in this forum. I suspect that some manager Lenovo check this forum. My problem has been resolved as soon as I posted my experience here.

  The IBM product portable grand, but I wish they hire more agents for sale or magazine somehow their service.

  Marry Christmas

• bad start with rotating globe

  I was shocked to see this so called support and began with control R and done a tune up at all the possibilities. It is now working very well but I decided to unplug my iphone, I had connected for charging when in my computer.

  Can someone tell me what happened and WHY this past?

  TKS

  On the screens, you see when you start your Mac - Apple Support

  If you see a globe turning instead of an Apple logo, it means that your Mac is from a boot disk based on the network as a Netboot or recovery of the Internet instead of a boot floppy connected or integrated. If you mean to your Mac start off this way, press and hold the power button to shut down your Mac. Then, press the power button to start normally.

• My iPhone 6 guard making his power on and off loading when it is connected with the MacBook Air early 2015

  Hi Please help me. My iPhone 6 retains what load noise when connected with my MacBook Air early 2015. It makes me crazy! I tried with several real Apple's USB cables, update to the latest iOS (phone and MacBook), updated the iTunes, clean the orifices, everything! I just got this MacBook on the Apple store. Please help me! Thanks in advance!

  Hi mikaelaridz,

  I understand that you just bought a MacBook Air in an Apple store, and when you plug your iPhone 6 in it, you are to hear a sound indicating that the connection does not work.  If your MacBook Air has a port USB - C, you must use the USB - C for Lightning cable to connect your iPhone.

  Using the USB - C port and adapters on your MacBook (retina, 12 inch, early 2015) and later

  Port USB - C

  USB - C is an industry standard generation that allows to load and transfer of video data - while a simple connector. Your MacBook comes with a USB - C port:

  

  Through this port, you can:

  • Charge your MacBook.
  • Power output.
  • Transfer data between your MacBook and other devices.
  • Connect the video output such as HDMI, VGA and DisplayPort.
  • Connect to other technologies, such as Ethernet.

  Port USB - C on your MacBook supports data transfer speeds to up to 5 Gbps (USB 3.1 Gen 1).

  USB - C for Lightning cable

  Apple USB-C for Lightning cable allows you to connect any device equipped with a connector of lightning with your MacBook. It provides data transfer and power of lighting fixtures. For example, you can use this cable to connect your MacBook to these devices:

  • iPhone, iPad and iPod touch
  • Magic Mouse 2
  • Magic keyboard
  • The Magic Trackpad 2

  You can also load these devices without using your MacBook by connecting to the C - USB to the lightning cable and plug the cable of the USB - C 29W power adapter.

  USB - C for Lightning cable supports data transfer at up to 5 Gbps (USB 3.1 Gen 1).

  This cable requires no power to operate. However, devices that you plug into it could draw power from your MacBook, you should unplug it when you're not using it.

  If this isn't the issue, then I suggest taking your new MacBook Air and iPhone at the Apple Storewhere you bought it.  A genius can inspect your computer for you, there is no hardware problems and staff can help you set up.  Here's how Contact Apple and make an appointment.

  Take care

• Hai, my ipod shuffle when it is connected with the computer, it flashes organge light.  If I don't take no light

  Hai, my ipod shuffle when it is connected with the computer, it flashes orange light.  If I remove without light and music.  Even I kept connected all day with my laptop for charging.  But without success.  Is it possible to change the battery?

  If the shuffle still appears in iTunes when you connect, you can try to do a restore using iTunes, where the cause is a software problem.

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod settings - Apple Support

  If the problem reoccurs after the restoration, it's probably a battery worn.  Need soldering skills to replace yourself, and iPod shuffle (with the exception of the 1st generation) is very small.  Not easy to work on.  This web site has repair guides

  https://www.iFixit.com/device/iPod_Shuffle

  and parts are available from sources like eBay.

  Apple 'serve' the shuffle, if it's the 4th gen (current type).  Rather than change the battery of your device, you get a replacement unit.  According to this document, out-of-warranty fees are $39

  Pricing of the Service - The Apple iPod Support

  NOTE: If your shuffle is less than one year of the date of purchase, it is under warranty.

  The retail price of a brand new 4th gen iPod shuffle, with new headphones, docking cable and warranty of one year is $ 49.

• Tecra Z50-A-14 t - bad connection WiFi signal

  In short.

  Absolutely the same problem with my new Tecra.
  Stable connection by cable.

  Bad connection same 3 5 meters from the router. If the distance is longer, or I use the laptop in another room sometimes it s no link at all.
  The card is Intel (R) Dual Band Wireless AC-3160 and that article how I found the link above.

  All electronic in the work of the House with no problem, but this piece of garbage to Wi - Fi only the same has even after 3 visits in the repair shop. And that s for new out of the box laptop.

  I really disappointed me.

  + The message was edited: link has been removed - forum rules +.

  Hmm. have you noticed the same problem of weak signal using the laptop to the power of the battery as well as connected to the adapter?

  My signal low similar knowledge questions may seem due BOF WiFi enabled power saving settings. This setting can be found in the current power plant? Advanced settings

  On the other hand, it might be possible that there is something wrong with the WiFi antenna cable. Maybe it is not properly connected to the mini PCI module

  In the case of changing the settings would not help you and if your already updated the Wlan to the latest version available, I think that the Toshiba certified maintainer should check the antenna.

• Is it possible to connect with FACEBOOK Customer / Tech Support? I got my ID stolen FB and I can't connect with a living soul!

  Is it possible to connect with FACEBOOK Customer / Tech Support? I got my FB ID stolen and I can't connect with a living soul! I'm really tired of FACEBOOK and ZUCKERBERG, boasts getting its 1 billionth Member, meanwhile, its members have problems with scams, hackers, even FACEBOOK is now BANNING people for the addition of family and friends! This must be a scam any seriously! Im sick of him, he turned my whole as for social networks. If it wasn't for the fact that I have almost all of my family in Europe and around the world all in one place, I would certainly remove my account. The problem with that is if you delete your FACEBOOK PROFILE, you don't actually remove them. FB keeps them because they are the property of Facebook the minute climb you the post! This information is in the conditions of joining Facebook, but not on the registration page! that is wrong with this picture. THEY HAVE NO SUPPORT, NO CUSTOMER SUPPORT, IT IS Y HAS NO PHONE NUMBER YOU CAN CALL TO REPORT YOUR STOLEN ID AND NOW I HAVE TO ALL RUN IT AROUND TO TRY TO FIND A CYBER CRIME UNIT WHO WILL HELP ME! How can the other thing, I know if Mytechgurus.com is a legitimate business. As I've been hacked and my ID stolen (curiously enough all what's happened just as I was banned from Facebook to add a friend, I've not seen in 36 years.) They have deleted my friendship with her and banned me for 7 days)! Facebook. MyTechGurus.com have charged me $700.00 for 2 pc for serivce of 24/7 for 2 years. Granted they have always been there in the last 6 weeks to help with all the problems that the pirate had created. They've phoned while I had a technician remote access online help with verbal information as it was a huge problem. but I put it back now because a governing body here in Australia called SCAM WATCH who is supposed to tell you who is a scam and is not was good enough to tell me that they are there only to report a scam, they can not physically tell you if one of them is actually a scam or not! I was left to literally chasing my own tail! HE IS THERE ANYONE TO HELP ME AT ALL!

  Hello

  Sorry, we can not help except at the point you in the right direction.

  The Microsoft Community is a site of support of peer reviewed for Windows
  and some Microsoft Products and has absolutely no connection or influence
  with Facebook.

  Rob - SpiritX

• HP G61 problem with charging the battery.

  Dear Sirs, I have read so many posts but I could not find a solution, so I decide to post one on my own.

  I have a HP G61 and work properly it works. The problem I have is with the battery.

  If I scream at the bottom of the laptop and leave it with the charger on when I start the laptop battery is full 100%

  during the initialization of the light of the current passes, the HARD drive light is normal and sometimes the charge light is on, a few times is off.

  I noticed that a lot of ppl have similar problems, so what I have is that

  With a multimeter, I have seen that the output power of the power brick is very well! Besides that I had three laptops computers HP with the same power supply, so I try this brick to the other laptop seems to work very well with the other laptop. I try another laptop PSU to this one and had the same problems.

  I concentrate so that the problem is in the battery. I download the HP battery checker and scan my bat (was100% charged) and the result was OK!

  so the mystery in this case is that the laptop does not work properly, I try full preformance, no problem at all, just the battery runs faster (make sence)

  While the laptop is running the power cord is plugged and there is no light on the side of the connector but there is light ot the power on the laptop.  As I m working with the laptop, then the charging light lights up and the battery seems to be linked to HQ and charcging.  sometimes says connected but no recharge! When I have the indicator of hip and pricing that could will a few seconds, then disappears and returns to the mode of unloading...

  If I shout down the laptop and let it connect with the brick power then the perception led can be turned off, but after a while turns on and stays on for a long time seems so at the normal charge...

  I know that sounds strange and crazy, but that's what happens...

  That this laptop works properly and I m ok with his performance (to the extent of the rest turned on) I see no reason recycling!

  the only annoying, it's that sometimes can not fresh at all so that it is turned on and of course after a while goes out...

  the battery is an original HP battery and if it is loaded to 100%, last up to an hour and something...

  hope I gave you a complete picture of what's going on with this machine.

  I tried also a few solutions that I found on the internet about the parameters of power controllers, ACPI etc. which seems to fix the problem with the power of microsoft management. This has had a small solution for a few days and then return to the former status. (I don't know if windows restores some steps on their settings)

  If there is a problem of material at the end of the day on the mobo, I would like to know it there is a chip or controller or any other component that I can replace. (I m engnr electronic so I can replace it) I had a few dead HP G61 models with screens broken, etc. or broken mobos

  Thanks in advance

  Stavros

  Hi @Polykarpos,

  You already have the troubleshooting that I would have recommended to you.  At this point, you should contact HP Total Care at 1-800-474-6836 in North America or Start here if you live outside of North America.

• Unable to connect with the MIFI device.

  I have a Verizon Jetpack 890 L mifi device and an older model Dell laptop that is wireless. After spending two hours on the phone with Verizon, finally got the correct IP address for the device to 'connect' with the computer. The States of the computer it is connected to the device, but the device shows that it of just nothing connected to it, have tested the device with a phone and the Xbox and the two front showed connected and functioning with the device. But the computer does not connect to the internet. Help, please!

  The message "the network password needs to be 40bits or 104bits depending on your network configuration. "This may be criteria such as 5 or 13 ascii characters or 10 or 26 hexadecimal characters" means that the system used encryption is WEP (instead of WPA or WPA2).  Although it is the lowest available wireless security, now that I think about it, I'm a little surprised that the mifi comes with a wireless security is enabled.

  There are at least 3 different "passwords" potentially used by your device.

  1. There may be a password that allows the device to connect to cellular service.  As far as I can tell from the manual, it is a "PIN code" that may or may not be required by your cell carrier (i.e., Verizon).  See page 15.

  2. There is a password that gets access to the configuration of the mifi utility.  This is the password that is supposed to be printed on the back of the mifi AND displayed on the LCD when the mifi is turned on.

  3. There may be a password for encryption (or "network key") wireless as the wireless mifi and your computer is configured to use WEP, WPA or WPA2.

  The more I read the manual for this device, I am convinced that the default setting for wireless encryption is 'None' and the password on the back of the device #2 above.  On the other hand, I can't imagine how he could have set himself up for the WEP encryption.

  Here are my latest suggestions.

  1 reset the mifi to factory default.  Beside the decision-making when the power cord is connected is a small button.  With the power on, press and hold this button. The manual says only: "hold."  I would like to keep the button pressed for at least 20 seconds or until there is some indication on the screen that a reset has occurred. You will need a unfolded paperclip to press the button. See http://support.verizonwireless.com/clc/devices/knowledge_base.html?id=50011#alt

  2. make sure that the battery is fully charged.

  3. turn on and confirm that the connection ('up' and 'arrows'), (e.g., 4 G LTE) service and the strength of the signal (bars) are turned on:

  

  4 wait about 10 seconds and then go to "View available wireless networks," find the one that matches your mifi (check to make sure that you do not have a neighbor with a mifi with a similar SSID) and click on connect.  You should NOT be asked for a password.

  5. open a web browser and enter the address 192.168.1.1 OR vz.hotspot in the address box and click GO.  You should see the following text:

  

  6. Enter the password of the sticker on the back of the mifi in the box and click on the button "Login".

  From there, you can follow the manual to configure wireless security settings.  Good luck.

• My Sprint HTC Android mobile phone connects with the supplied USB cable, but the computer says 'No HTC Device Connected'

  My Sprint HTC Android mobile phone connects with the USB cable, but the computer says 'No. HTC Device Connected' so I can't sync...

  Hello

  1. do you have HTC Manager installed on the computer?

  2. have you tried it with different USB ports?

  You need the HTC Sync HTC phone Manager software.

  Method 1: Try again with different USB ports and see if that helps.

   

  Method 2: If HTC Sync is installed, if you get the message "no device connected" in HTC Sync, ensure that your phone USB setting is changed to "Charge Only" to "HTC Sync".

  If the methods above do not help, you can contact HTC for additional help.

  Here is the link: http://www.htc.com/us/support/

• Smartband SWR10 not connection with phone after update of Lifelog

  After yesterdays updated my smartband does not connect with the phone. No data is transferred and the message inside SmartConnect says "Connect charger" (but I don't know that it is fully charged). Same situation was around a month ago, and it's getting boring. Is it possible to fix it?

  OD, double relocation at all connected with smartband and restart helped smartband. I have node know what was the problem, but it is resolved.

• Sky wireless broadband does not connect with Vista

  I just changed my BT broadband to Sky.It works fine on my Mac but not connecting with my roommates PC that uses Windows Vista.After calls long with sky they said there is a problem with the DNS. I tried to call Microsoft, but they want to charge me which I am unwilling to do. I can connect to the internet on the pc with the thin Ethernet cable. In the center of network share, I have a cross between the network and the help of Internet Icon.Please as it should be sorted as soon as POSSIBLE and I cannot believe with such a company big as the sky that has thousands of customers, they say that it is a known issue and there is nothing they can do... So basically they say that anyone with Vista cannot use their wireless computers!

  Help, please...

  Hello pookieboy140,

  I suggest that you start with the management of Network Diagnostics on the computer that will help you in error, like why you are not able to connect to the Internet.

  You can refer the link that will give you information about this below:

  http://Windows.Microsoft.com/en-us/Windows-Vista/using-Windows-Network-Diagnostics-event-logs-to-solve-network-problems

  Since you are not able to connect to the Internet, the best way to solve this problem is to contact your service provider.

  Thank you
  Irfan H, Engineer Support Microsoft Answers.