Basler a601f ieee 1934 any pci card?

Similar Questions

• What ieee 1394 pci card Fireware should I install to my hp pavilion h8 1234

  What ieee 1394 pci card Fireware should I install to my hp pavilion h8 1234?  I need to run a Nikon Super Coolscan 8000 Ed currently using Windows 7.

  Thank you

  2Wander

  A PCI Express x 1 card that is compatible with the operating system installed. You can find one at NewEgg.com or another provider online. Use Google or Bing to find the one you need.

• DVI PCI Card/s for G3 minitour

  I am a new Member of this forum and I hope that someone has the necessary answersI. I have a Power Macintosh G3 Beige minitour @ 333 MHz, and I'm on OS 8.5.1. There is a reason, I must stay with OS 8.5.1.

  I am wanting to know if there is a Dual-DVI PCI card that will work in this machine, so I can run two monitors via DVI in order to get a higher resolution than is available with VGA. My understanding is that VGA tops out at 1280 x 1024 and I need just a little more.

  If there is not an available Dual-DVI card that will work with my setup, how about two single DVI cards? If, by chance, there are two ways, that would be better and two monitors can also..., run off PCI cards without involving the port of regular monitor of the factory. If the port of the factory to be used, is there an adapter (or adapter cable) him/DVI.

  I know it's several questions, but get them out of here, in my first post may save some back.

  Thanks for any help, Tom

  Hi & welcome!

  In fact, VGA will give you more resolution than DVI.

  Radeon 7000

  The 32 MB memory DDR (Double Data Rate) will also help, allowing your computer to display very high resolutions up to 2048 x 1536 at 60 Hz if your analog monitor supports. Resolutions up to 1600 x 1200 are supported using digital flat screen, depending on the individual abilities of your LCD monitor.

  http://www.Macworld.com/article/1004789/radeon7000.html

  http://www.xlr8yourmac.com/graphics/radeon_7000_feedback.html

  There are faster cards still better, but more rare and the fastest I had were Formac cards, can have a couple somewhere here.

• Satellite A30 - 303 install wireless mini PCI card internal

  Hello
  I am installing a PA3300U (Atheros) mini PCI WiFi internal card and have a basic question that I hope someone will be able to answer. There are two cables, white and black (under the cover of the wireless card on the case) which I suppose are for the internal antenna. The question is where do these attach to on the mini-PCI card (unfortunately I have no instructions for the card mounting)?
  I'll be very grateful for any assistance with this.
  Best regards, Dave.

  Hello

  I don't actually see one of the Atheros cards, but on other brands, there are two connectors that are marked with the HAND and to THE.
  A white cable normally goes to the HAND and a black to the auxiliary voltage

  BR

  Tom

• SP A10 with mini PCI card

  Help!

  Had great success with Toshiba would like to use it in wireless mode. LAN mini PCI card switch have still can not find the drivers on the computer to enable.

  Any suggestions

  Thank you very much

  Steve

  Hello

  What type of card LAN Mini PCI do you own?

  Please publish the name of the vendor, the name of the map and so on!

  Goodbye, Meier

• Startup gets "Network cable unplugged" on (new) wireless mini-PCI card

  Repost in the previous topic was locked, but has not been resolved. Original post below, please see previous post for more details

  I recently installed a Netgear DG834GT wireless router and now have intermittent problems connecting my Tecra 9100. If the 9100 has been off for awhile (like overnight), when I restart I get always "Network cable unplugged" for the wireless connection. Reboot several times (anything from 3 upwards) I finally get connected to the router and everything then works fine for hours. Even a quick restart at this point (that is, once that the wireless adapter is connected) does not cause a problem, but as soon as I leave the stop of the machine during a time he fails again on restart.

  There are no errors in the event log.

  I am using wireless mini-PCI cards and have already updated to the latest version of the driver.

  Any ideas gratefully received, for now every morning is a 20 to 30 minutes of rebooting frustration trying to get my connection work.

  (Running Win2K professional)

  Hello

  I have the same problem if I stand for laptop and access point at the same time. If the access point is already in use, the connection is established shortly after. First the access point must establish a connection to the modem. Now the wireless connection is not available.

  I guess after the second reboot, the connection between the AP and the modem is already finished and you can use the network wireless successfully.

  Good bye

• ? PRO/Wireless mini PCI card will switch

  This question has been posted before, but I have not found a solution

  I have installed a PRO mini-PCI card / Wireless 2915ABG in my A30. It is recognized as a card very well, but I can't turn it on. Not with the switch and or the software.

  Any tips?

  Hi rothirgo,

  As far as I know Satellite A30 series is built with Atheros and Agere wireless card. This means that Toshiba has been test machines with just these two cards and do not support another manufacturer of the WL card for this machine. If you have the Intel card and good driver, it should work too.

  Is in the device, a problem Manager? When your card has been properly installed, go to control panel > network connections. If there is Wireless Network Connection showed that it should be enabled.

  If you do this, you can now search for available networks in the wireless network connection properties.

  Just one last question. You have wireless on / off switch on the left side of your laptop? What Wireless Card on FN + F8 check if there is an answer.

  Please let me know what you have done and are there any error messages.

• How can I install a full-size pci card in a Slimline desktop environment

  I got a s5623w computer Slimline of office for a gift.  A year later I wanted to install a pci card hardware to capture analog video and transfer it to digital to my computer.  Well, I've been very disappointed and found that the map is too long.  What type of equipment or upgrades can even installed in the slimline computers anyway?  Is there a way for the size to connect to this computer?  The material I want to install has taken to a VCR and a port IEEE 13694 (who was left out of this model, why I have no idea) is it possible to install it or did I just lose a lot of money.  Or is there a special place to purchase these short hardware PCI cards?

  Please consider using a video capture device / USB like these for VCR (analogue) type signals. In regards to a Firewire/1394 card, consider the SYBA Low Profile PCI-Express 1394 b/A, StarTech PEX1394B3LPor SIIG FireWire 400 PCI Express x 1 rack w/LP

• Tecra 9100 - W-LAN-Mini-PCI-card upgrade

  Hello everyone,

  I ve got a with the W-LAN-onboard Tecra 9100 working doesn´t.
  Instead of repairing the old W - Lan Mini-PCI-card I want to move to a new standard (802. 11 b / g with 108 Mbit/s max) Mini-PCI card.

  I prefer the mini Notebook-WLAN-Gigabyte GN-WIAG02 PCI adapter.

  Is it possible to chance the card built into the Gigabyte card?

  Hello

  It s nice that you want to upgrade your wireless mini-pci network card. But I suggest you rather a card with an Atheros chipset. The best choice is perhaps a card with a Chipset of Atheros 5005GS since I upgraded my Tecra 9100 with this card and it works like charm. (and not so expensive as other s cards)

  To swap the card, you must remove the plastic cover of the keyboard and unscrew the two screws in order to release the keyboard.
  After removing the keyboard, you will find an aluminum side cover left which is set with a special torx screws. The best would be to get these torx screwdriver to loosen this bolt and remove the cover.
  After removal, you will see the map with the cables that lead to the antenna. (One white and one black) Be very CAREFUL when remove the Connector cables, because if damage you one of the cable connectors there is no return since the cables are cables "Mini-coax" and cannot be "connected."

  I warn you, just do it if you're really sure and if you know what you're doing, because I won't take any responsibility if damage you something on your machine. Otherwise, I wish good luck and would appreciate some comments on your success.

  See you soon

• Satellite 5200 903: Mini PCI card does not work

  Hello

  I am a user of one:
  Satellite 5200 903: P4 - M 2.2 / 256 + 256 DDR/60 GB/15 t SXGA + / DVD - R - RW / nV FX 5600/SFP/WIFI ready/XP

  My computer is a Toshiba Wirless lan Mini PCI Card.
  I installed the card a few years ago - everything worked great.
  In early 2006, I installed a new operating system (XP Pro + SP1, same system as before) because it was necessary.
  I installed all the drivers for the card of W - Lan, of course, the map worked in a good way (no driver incompatibility or other problems).
  But, and this is the reason of this topic here. It is not possible to connect my card to any hot spot. I tried with 2 different access points, but the result is the same. 'No connection Point found '.

  Does anyone have an idea of what to do or where I could look for failure? Is there maybe no special software required (I couldn't remember that I needed in my last installation special driver or software)

  If more information is needed, please let know me.

  (Sorry for the bad English, but it is not my first language.)

  THX for your help

  Hello Christian

  First your English is fine, and I'm sure that every user will understand what you want to describe.
  Back to your problem: the wireless card properly recognized and listed in the Device Manager?
  If so, please be sure that this card is enabled. Just that you should be able to see any wireless network.

  You n t need any special software. WIFI connection can be configured using settings in windows.

• Selection of DAQ PCI cards - pulse based on the position of the AO

  I build a replacement computer for an aging instrument control system, and I'm trying spec a PCI card to use.  My line of sight is on the M6229, but I'm a little confused as to if she's going to do what I want.  We will use LabView 8.6 for the software, and RT module is not an option.

  The question has been posted here in various forms, but I think that this iteration could be a little original:

  The requirements of the program are:

  -Two analog outputs are used to generate a raster 2D model, while the internal counter counts the pulses of preamp at each stage of the grid.

  -The dwell for each point must be controllable by the user (ideally as low as 0.01 ms), and the count rate can go up to 5Mcps.

  -The number of points x / y in the raster model is controllable by the user, a will have a maximum of 400 x 400 (160000).

  At the moment I'm simulating a 6229 in MAX and written a model of Sawtooth on channel X and a linear ramp on the channel of Y.  The sampling frequency / can be deducted immediately requested size of dwell and pixel of the user.  I generate the set of values of xy 2D matrix and write to data acquisition.  I use voluntarily no more points that are necessary, because this application prefers one out an alias on the AO conducted, channels to maintain a separate position for each pixel in the detector.  Thus, for example, for a 100 x 100 pixel image with 1ms live per pixel, the quick scan signal is essentially a 100 Hz sawtooth, sampled 100 times at a sampling rate of 10 kHz.

  However, the frequency of sampling for the pulse counter must be very high to follow with the input of the preamplifier signal.  I think that I can't have separate sampling frequencies for two separate tasks, so I'm left with a choice between creating an XY array unnecessarily large to match the sample for the pulse counter clock, or ask your question here

  Does anyone have any advice? In the end, I want to make sure we buy the best equipment for the job, but as always, we are also interested in the best bang for the buck.  Is a map of the M series not up to this task?

  
  

• HP Touchsmart 600-1105xt - PCI card

  Hi - I am trying to add support for USB 3.0 to my TouchSmart 600-1105xt system and I found that there is 1 slot mini-PCI express. However I have not sure how to add to my system. Its different for a touchsmart since all are crammed into a small place and I don't know how to expose the PCi Card without breaking anything. Any help is appreciated.

  There is NO external ports,

  you will have to completely disassemble the unit to join the mini-pci slot which normally has the TV tuner in it.

  As I said, this is not repairable.

• Could not receive data from GPIB system controller (PCI card of NI - 488-2)

  Hello

  We create a daughter card that will allow our product shipped to communicate via GPIB. This girl GPIB card must be able to receive the SCPI message send by system GPIB controller and reply to the message. In my current configuration, system controller is a card PCI of NOR-488. 2 installed on a PC running Windows XP.

  On the side of card GPIB girl, we have NAT7210 with 75160 and 75161 transceiver chips. NAT7210 is connected to the interface of static memory controller (SMC) an Atmel ARM9 embedded Linux OS running. We use the Linux GPIB library on sourceforge - http://linux-gpib.sourceforge.net/ .

  For now, chip NAT7210 initialization stage seems to be successful. Using Measurement & Automation Explorer software that comes with the NI GPIB PCI card, it is able to detect the daughter GPIB card; the cushion and the sad values are correct. However, chip NAT7210 has failed to receive the * IDN system controller message.

  Here's what I did to initialize the NAT7210:

  (1) set 0 x 99 in SPMR register. To make sure that we are 7210.

  (2) in AUXMR the value 0 x 02 (chip reset at the controls). To affirm the message local pon.

  (3) skip the step that defines the ICR and registered ICR2 because we use the default clock 8 Mhz.

  (4) the value 0 x 31 (addressing Dual mode) in the register of the ADMR.

  (4) together in ADR 0x01 to register.

  (5) contained SPMR 0x40. Initial response of series. I don't know what are reasonable values to settle here.

  (6) together to register 0x07 in hidden PPR. Do not participate in the parallel polls.

  (7) set TASKS and NTNL bits in the AUXRG register.

  (8) the value 0 x 51 (hldi to the order) in the AUXMR register.

  (9) to activate the interruptions; IMR0 = 0xC5, IMR1 = 0xBF and IMR2 = 0x4F (no plans for DMA transfers).

  (10) the value 0 (command pon) in the AUXMR register. Final step.

  The NAT7210 Linux configuration file content:

  minor = 0

  board_type = "gpib".

  name = "gpib0.

  PAD = 1

  sad = 96

  Timeout = T3s

  EOS = 0x0a

  together-reos = yes

  all-bin = no

  together-xeos = no

  together-eot = yes

  base = 0 x 70000000

  IRQ = 45

  DMA = 0

  master = no

  Any ideas on what could be the reasons NAT7210 has failed to receive the * IDN system controller message?

  Steve, thanks for your comments.

  It turns out that the deactivation of functions that print messages in the debug library has solved the problem of reception.

• BNC-2110, 6023E PCI card and Labview V9.0: is the sensitivity of data acquisition (change more little detectable voltage) 0.002V?

  BNC-2110, 6023E PCI card and Labview V9.0: sensitivity of data acquisition (change more little detectable voltage) is 0.002V

  Hi, I use the software/hardware above to read a voltage of a potentiostat world Precision Instruments No..

  I'm trying to record changes in voltage as low as 0.0003V but using the wizard DAQ, I seem to be limited to a sensitivity of 0.002V.  This is the limit of real sensitivity or have I missed something?

  Any help would be greatly appreciated.

  Hi DCAM77,

  Thanks for joining the forums!

  The PCI or 6023E has a 12-bit ADC.  In other words, it can make the difference between 4096 (2 ^ 12) different levels within the range of cards.  The card you have has a selectable range by ± 10 V, ± 5 V, ± 500 mV or ±50 mV software.

  This means that the minimum detectable variation will be 4 mV, 20 mV, 244 µV or 24, depending on the chosen range µV.

  You should be able to use the ± 500 mV or ±50 mV to get the least significant bit (LSB) value, you need, even if it means that your signal is located between these values.  If not, then you need to consider other materials to the application, or the addition of external circuits across the signal.

• What is the correct USB 3.0 PCIE card for Z800?

  I am looking to buy the correct USB 3.0 PCIe card for a Z800, but I can't find any HP thru. Anyone has the info > 12 and 60 cards HP dollar on EBAY, but I don't know if those who are good.

  Hello

  Based on the following specifications, the machine has a lot of options:

  http://h18000.www1.HP.com/products/QuickSpecs/13278_na/13278_na.PDF

  You can buy 1 port card, map 2 ports, card port 3 or even 4 ports card such as:

  http://www.StarTech.com/cards-adapters/USB-3.0/cards/2-port-PCI-Express-SuperSpeed-USB-3-card-adapter~PEXUSB3S2

  You should check the slot to get the support of the card right.

  Kind regards.

  PS eBay is another story, you can buy some card dollars.