BEFSR41 router problem

Similar Questions

• Need help installing BEFSR41 router

  Hello

  I need some help configure a router BEFSR41, that I bought recently.  A year ago, I got a WRT54GS router and was able to set it up to my Siemens modem DSL 4100 b without any problem.  (Maybe I was just lucky before when I set up the wireless router)  Now I have misery BEFSR41 to work.  I tried to replace my BEFSR41 in the same position as my WRT54GS by using the same configuration.  I'm reproducing the setting on my WRT54GS BEFSR41 router to the wired connection. I took the "Automatic Configuration - DHCP" on my WRT54GS, so on the BEFSR41, I choose "obtain an IP address automatically".  I also activate local DHCP server from 192.168.1.100.  This should configure the BEFSR41 as WRT54GS, right?  But I couldn't get on the internet using BEFSR41 with this configuration.

  I checked the routing table for the two router see if it makes a difference and noticed that the only thing different is that the routing table for BEFSR41, the fields of the gateway is 0.0.0.0, but they have correct values on my WRT54GS.

  Another difference between the two routers is that on the screen of my WRT54GS State, he showed entry 192.168.0.1 DNS1 and DNS2 and DNS3 entries are empty.  On the State of BEFSR41 screen, it showed DNS1 as 192.168.0.1, then he repeats DNS1 as 192.168.0.1, and finally another DNS1 entry is empty.  How important is it that on the status of the BEFSR41 display, is to show field DNS1 3 times? (instead of DNS3 DNS1, DNS2)

  Thanks in advance for any help.

  I suspect that the reason the 4100 and the BEFSR41 do not play well together is that both of them use the proxy DNS servers.  DNS proxy on the BEFSR41 servers run 192.168.1.1 and the DNS proxy on the 4100 servers run 192.168.0.1.   My bet is that "double proxy servers" are simply not passing addresses correctly.

  As to why the 4100 b works with your old router, but not with your most recent router, I'm not sure.  Is your 4100 several years old?  Often old modems work with older routers, but not with the newer routers.

  I think that it is best to place your 4100 b in Bridge mode.  It would like to convert it to a real modem.  It therefore would not have an IP address, or make your PPPoE connection.  This would be "Not used PPPoE" (on the modem).

  Your BEFSR41 would have to be configured to your PPPoE connection.

• Network Magic cannot discover a "BEFSR41" router behind a "WET610N" wireless bridge

  Just upgraded to a WRT610N 2 version in my office.  He pulls an IP address from my cable router and distributes IP addresses (this is setup for DHCP) without problem.  I need to extend the home network to another part of the House so I took 2 x WET610N wireless bridges.  Since many devices will have to use the bridge I'll recycle my BEFSR41 as a switch.  I have the router configuration and bridge; the bridge connects to the port "uplink" on the router, and the DHCP has been disabled on the router.  But when I run Network Magic BEFSR41 router cannot find the other side of the bridge.  Any ideas?

  You need this post in the section Network Magic from this forum.  If the router acts as a switch, it will be transparent and not e seen.

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• Has lost all contact with BEFSR41 router via network

  Hello

  in this thread: -.

  http://homecommunity.Cisco.com/T5/wired-routers/BEFSR41-v3-activating-UPnP/m-p/101243/highlight/true...

  posters describe the problem that the original password is damaged if UPnP is enabled.  A poster gives the password which is replaced in an arbitrary manner, but when I tried (after having the same problem), I couldn't make it work and he had to restore factory settings and repeat the configuration from scratch.

  Now, for some reason, I can't do it yet!  "admin/admin" is no longer accepted, and if instead, I try to open the configuration using the Wizard installation CD I get an error message saying "unable to connect...". "and tells me to press the"reset"button (which of course I did, nothing helped).  However, ping the router produces an immediate response with success and my internet access is as before.

  Please, what can I do to get out of this endless loop?  There are some configuration changes, I need to do and I can't!

  If your router works fine then you don't need a re-flashing the firmware on your router.

  As far as disable UPnP is concerned, maybe it's a bug in the firmware.

• Strict NAT with a BEFSR41 router

  So I play frequently on my xbox 360 and I like to browse my computer when I'm waiting for a match. With my old router, same brand and model, all I had to do was do port forwarding with the ports recommended on xbox.com and enable upnp and I had no problems to connect to games, joining friend games or assembling them mine.

  So when I got my replacement router I have activated the same options as before but kept getting the strict NAT message when I start a game and none of my friends could join my game and I couldn't join them. So I enabled the DMZ and clone the MAC address of xbox 360. He got rid of the NAT strict message but I noticed a significant drop in the speed of the internet, yet none of my friend could join my game and I couldn't reach them.

  So I had to unplug the router and connect the xbox directly on the modem I have while waiting for the replacement router and I could do all the things as before. So it leads me to believe that there is a problem with the router. I have a linksys BEFSR41 v. 4.3 router and modem motorola with a DSL connection.

  Any advice or ideas would be greatly appreciated.

  Yes, you are right that if the modem acts as a router, it should be filled if you want to connect to another router... If your modem is full you will not get the internet light on your modem (it will remain off)...

  Once you configure the modem in Bridge mode full you must configure the type of internet connection of your router in PPPoE and enter the correct user name and password provided by your Internet Service Providor (ISP)... Once done, click on save settings...

  Click the status tab and search for an IP address, if you get 0.0.0.0 for the IP address click on the Connect button and weait... Power Cycle your modem and your roputer for a minute and see if you can go online... Once you are online, you can make the settings as shown in the previous post for your X - Box and it should connect...

• OfficeJet 6600 e-all-in-one: Wireless connectivity with the new router problem

  We had the printer since 12 months, workin with no problems.

  Just got a new modem/router (NETGEAR V7610) installed as part of the NBN implementation and I can't get the printer to connect to the new router. 5 and 2.4 G active networks. The two defined newtorks on security WPA2-PSK [AES].

  The printer detects the wireless (2. 4 g) network, but can't coplete the connection. Tried the two direct input the network key and using WMA.

  -The display panel shows "wireless invalid password (WPA) is entered.

  -The results of network printer test page indicates a FAILURE on safety.

  I was able to connect to multiple other devices (laptop, iphone, Kindle...) without any problem. Used the two direct entry of the key network and WMA.

  Anything else I can try?

  Find a new update of the firmware for the printer (May 9, 2016).

  After you apply the update, the printer is able to connect to the new modem.

• Satellite A100-014: connection Wireless D-link router problem

  I think that it is working properly. I keep getting kicked from WLAN (connected to the dlink DWL 900AP), but if I plug the Ethernet cable it works very well.

  This vista software is a major pain. It will let me install the d-link software.

  Does anyone have any knowledge about it?

  If you need the d-link software you must ask the manufacturing of router for these updates or visit the support site for manufacturing.

  What WLan encryption are you using? I used WPA2 and I had similar problems.
  My router and the wireless network card were not 100% compatible with this encryption.

  Now I use the WPA or WEP and it works.

• Time Capsule router problems

  Recently, my wireless network has had problems.  He became more and more slow.  My devices connect without problems and the signal is full but it takes significantly more time to do something about it.  My iMac doesn't seem to have problems but are my other devices (phone, Tablet, PS3, PS4).  Netflix is essentially very bad because it keeps buffering every 30 seconds and I have to run PS4 upgrades must run all night because they take 8 + hours to download.  I had questions about 5-6 months, which I was able to correct by closing all the way down, 20 minute wait and then turn the modem, the router, and then the computer.  I tried again twice, but he don't seem to have any effect.

  My modem is a Motorola Surfboard SB6141.

  My router is a time capsule, model A1409.

  iMac is a model 27 inch late 2009 10.10.5 running.

  The capsule is connected directly to the modem via Ethernet.  All other devices are connected to the wireless network.  Any advice would be greatly appreciated.

  Thank you!

  Something directly connect to the modem by ethernet. And do a test to see if download and shipping limits are together and working properly.

  You must turn off the modem at each change of customer... 5 minutes is probably enough, but this can take up to 15 minutes.

  If you have good speed then when you put the back... TC test via ethernet to TB... once again, you should get almost the same download and upload speeds as the test to the direct modem.

  Now, test your wireless... you say that the iMac has no problem... so please give us the numbers... It is difficult to work from vague descriptions...

  Then, I need to know the connection speeds and all possible information. Run diagnostics on the computer wireless.

  You should also do a factory reset full of the TC and reconfigure it as follows.

  Start from a factory reset. No files are lost on the drive hard in doing so.

  Universal factory reset

  Turning off the TC... That is, remove the power supply cord or the power at the wall outlet, wait 10 seconds... Hold the reset button... be nice... Turn on always even now in reset... and keep holding in for another 10 seconds. You may need assistance because it is difficult to hold in reset and power on. It will show the success quickly flashing led front. Release reset... and wait a few minutes for the TC to reset and return with the factory settings. If the front LED flashes quickly you missed and simply try again. The reset is quite fragile in these... Press the key while it is just click away and not more... I've seen people bend lever or even break. I use a toothpick as a tool.

  NB. None of your files on the hard drive of the TC are removed... This simply clears the settings of the router of the TC.

  The installer the TC.

  And then redo the configuration of the computer with the Mavericks - Yosemite - ElCapo. (MYELCAP)

  1. the use of very short names... NO APPLE RECOMMENDED names. Without the space and pure alphanumeric characters.

  for example TCgen5 for the base station and the name of the TCwifi wireless.

  If the problem is using wireless TC24ghz and TC5ghz with fixed channels as it also seems to help stop the nonsense. But it can be tried in the second round. IE, plan on a first and second series of changes to fix this... If all goes well... I note other steps can you tour2.

  2. use all passwords also consistent with 1. but maybe a little longer. IE 8 and 20 characters of mixed cases and numbers... no alphanumeric non-caracteres.

  3. If the TC is router, you can ignore this point. It is only a problem when the TC is bridged.

  If ensure that the TC is always the same IP address... you will need to do this on the main router using a dhcp reservation... or a bit more complex setup by using the static IP address in the TC. But it's important for deriving from intellectual property in all directions when MYELCAP do not remember his name for 5 min after a reboot done for poor network management.

  4. check that your share on the computer name does not change... Make sure that it is also in line with the above... short without space and pure alphanumeric... but this change will mess up your TM backup... so be prepared to make a new, full backup. Sorry... keep this one for the second round, if you want to avoid a new backup.

  5 attach the TC disc into the computer manually.

  In Finder, go, connect to the server in the main menu,

  Type in SMB://192.168.0.254 (or whatever ip of TC is that you made static. It's a default router 10.0.1.1 and I encourage people to stick with it unless you know what you're doing).

  You can use the name... SMB://TCgen5.local where you replace TCgen5 with your name of TC... local is the default domain of the TC and does not change.

  However the names are not so easy as... the IP address nor reliable. They are not at least not in Yosemite. The field can also be a problem if you are not clogged or wireless directly to the Treasury Board.

  6. ensure that IPv6 is set to link-local only in the computer. For example wireless open network, wireless and Advanced preferences / TCP/IP... and the difficulty of IPv6. link-local only. Do the same for the ethernet if you use it.

  It is a lot more jiggery pokery, you can try, but the above is a good start... If you still find not reliable... don't be surprised.

  You may need to do more work on the computer itself. for example, to reset the NVRAM/PRAM/SMC... helped some people. A clean installation of the operating system is also useful if you update installed.

• Communication of the computer/router problems

  I bought a wireless router and plugged into a line of cat-5 while it would broadcast internet for my ultra-livre, which of course is not an ethernet port.  Now I have access to the internet, but applications that use the internet, as the steam and Skype, does not connect.  What is the problem?

  Hello

  Welcome to the Microsoft community.

  I see that Steam and Skype does not work on your computer.

  1. What happens when you try to sign in to Skype?
  2. What operating system is installed on the computer?

  You must have a strong Wi - Fi connection to work on Skype.

  You can check this link for more information.

  https://support.Skype.com/en/category/SKYPE_ACCESS/

  Steam problem please contact steam to help support.

  Go back with the necessary details so that we can help you better.

• BEFSR41 connectivity problem

  I have an old router BEFSR41 V.2 that I pulled from the closet to use.  I can't have internet connectivity once I install it.  I ping the router at 192.168.1.1 but always no internet.  The router is dead?  Should I update the firmware?  I can't find links for this old router.

  I don't think that Linksys still has the firmware for older models of devices like the BEFSR41. I suggest you to reset and reconfigure the router according to the type of connection to your ISP. If you use a cable connection type, remember to clone the MAC address of the router during the configuration process. If you are using DSL with PPPoE, enter your PPPoE username and password on the router configuration page.

  Check out these links and use them as a guide:

  http://KB.Linksys.com/Linksys/UKP.aspx?pid=94&VW=1&articleid=3686

  http://KB.Linksys.com/Linksys/UKP.aspx?pid=94&VW=1&articleid=3687

  Note: Don't worry if your router configuration page appears differently than those indicated in the article.

• Installation with WRT310N wireless router problem

  I have currently an old model WRT54G Router installed wireless that works very well, but I need the WPS technology if I want to install a newer model WRT310N router. I used the installation cd supplied with the router, which has not seen any problem until I removed the old router and plugged in power in the new after connecting the anc ethernet cables to my cable modem. For some reason any the software wont recognize the new router so I can continue with the configuration of the installation. Since I plugged the new router in the same connections that I had had the old LInksys router connected to, I do not understand why and I can not proceed with the installation. I finally just reinstalled... connected., my old router and it works fine, but this isn't a solution for me.

  It might have something to do with the sequence to connect the different cables? I also tried to use 192.168.1.1. via my browser and could up the installation screens but it wont let me install the new router so that the old one is still in place and without the old one in place, I can not access the configuration on my desktop screens.

  I have my router in a closet with my... cable modem... .but the WRT54G worked fine for 2 years in the same cupboard and I also installed a Netgear N600 router as an alternative. is it installed fine until what happened to the point where he said the beach was too limited. .i guess work in the closet.  I guess I can buy a range extender to solve this problem, but I have no experience with those so im not sure if this will solve the problem. I prefer to get the Linksys WRT310N to work if possible.

  Thanks for any help you can provide.

  Thanks for the tips on how to handle this. Fortunately, I discovered later that the Linksys router, I bought on ebay, is apparently defective and it now resides in my trash. That said, I also realized with the help of a neighbor that my Kindle works with the good old Linksys router I used for 4 years or more. My problem was to not understand how to download books on the Kindle, even though I thought I did. So the problem is moot. Sorry I got worth this site with no problem.

• static IP address assignment to TiVo on BEFSR41 router

  Hello

  I'm trying to put in place a couple of TiVo cable already on my home network so I can 'see' on my Mac using the TiVo Express of Toast Titanium function and copy the TiVo on my Mac programs.   TiVo technical support suggested that the problem is that my Mac IP address is 198.162.1.100 (assigned automatically) and for some reason some of my TiVo is on 198.162.0.2 et.0.3.  They suggested that I have manually assign a static IP address for the for put them in 'sync' with my Mac address - that is to say, something in the range 198.152.1.xxx of TiVo.

  I was able to assign a static IP address of 198.162.1.109 to the head of the TiVo (and my Mac is still not see it), but I received an error message when I tried to assign 198.162.1.110 to the other TiVo.   Technical support suggested I check with you on assignment of the IP address via the router.  Can you tell me if this is possible and if so, how?

  Thank you!

  If the TiVo is Gets an IP 192.168.0.2 or similar when using dynamic/DHCP/Auto IP addresses means the TiVo is connected to a different router or get an IP address from another DHCP server.

  1. Please check your wiring. Your modem should connect to the internet, the port of the BEF everything is connected to the BEF. If the modem has additional LAN ports, a modem/router combo device. Do not use additional ports on the modem/router combo.

  2. If wiring is OK, as previously indicated another reason for a 192.168.0.2 automatic address IP sharing a computer inside your network that has been configured for an internet connection. With internet connection sharing you can share an internet connection through this computer. To do this, the computer will assign 192.168.0. * IP addresses on its side LAN. Please check your computers if there is one that has internet connection sharing enabled.

• Connectivity of the wireless router problem

  I have a Cisco's Linksys WRT160N wireless router.  After it is up and running, all my wireless devices work fine.  My sons Wii for my laptop, my wifes iPod Touch. But the strangest thing is happening.  I have problems connecting to the internet with my desktop computer that is hard wired to the linksys router.

  Often I can connect any... other times it's quite slow compared to when I plug my office directly to a cable modem.  Finally, sometimes certain aspects of the Web page will appear while others won't.

  Question: Is damaged?  Or is there something that I am missing.  You would think it would be right forweard enough... OH, I have also replaced the cables from the desktop to the router and have already done all the reboot that I care to do as well as redo the ip address in the part of the repair of my control panel.

  Any ideas?

  Access the Page of configuration of your router and lower the MTU size of the router to Auto/1500 to 1400.

• Interference WRT400N Wireless Router problem.

  Hello!  I would be grateful if someone can help me with my problem.  I live a mile on a mountain.  When a vehicle comes to the top of the mountain at a certain point, we get interference which causes the computer programs and the internet to freeze until the vehicle pass at some point.  Simply, this started about 6 months ago and is very frustrating.  How can I change the frequency channel on the Linksys simultaneous Dual - Band Wireless - N Router, model #WRT400N?

  On the wireless page, you have not selected Manuel as you're supposed too?