Best practices in VMWare ESXi 3.5 installation and deployment of VMDK u3?
Hi all
I'm about to implement virtualization on my business technology
I've got these resources to be used by VMWare ESXi 3.5
Dell PowerEDGE 2950 III
32 GB DDR - II 667 MHz
internal 4 x 500 GB SATA 7200 RPM HDD (RAID 5) - I know that it's slow to host the VMDK
Internal USB slot on the motherboard (but not USB flashdisk?)
Dell PowerVault MD3000
10 x 300 GB SAS 15 k RPM
2 x Dual port Gigabit Ethernet NIC (x 4 in total)
iSCSI - 2 x Gigabit Ethernet for the switch (mute not to VLAN)
I wonder where I should install the VMWare ESXi? for the VMDK, I believe that the deployment in the SAN is the right place.
and any suggestion for the use of the SATA HARD drive internal?
any comments would be greatly appreciated.
Thank you.
You mean Deployment.jpg diagram?
In this case, there is an error.
You need a network 2, not 4.
Each controller and each NIC (on ESX) must have an IP in a net and another IP in the second NET.
ESX guests 4 targets, 2 in a net, 2 in the other.
André
* If you found this device or any other answer useful please consider awarding points for correct or helpful answers
Tags: VMware
Similar Questions
-
best practices for the storage of the vm and vhd
no doubt this question has been answered not once... Sorry
I would like to know the best practice for the storage of the vm and its virtual hard disk to a SAN.
Any show advantage does make sense to keep them on separate LUNS?
Thank you.
It will really depend on the application of the virtual machine - but for most of the applications no problem by storing everything on the same data store
-
VMware ESXi freezes during installation
I have problems to install VMware ESXi on a HP dl380 g3. Accessing the server using its iLO interface. I boot from the cd and choose Setup ESXi. Then, it load the following modules (vmkboot.gz, vmkernel.gz, sys.vgz, cim.vgz, ienviron.tgz, image.tgz, install.tgz). After that, he said "Booting MBI = 0x000100d8, entry = 0 x 00100212" and freezes. By freezes, I mean that my keyboard is blocked so I can't even disable caps lock on or off. I let it sit for 10 min and she still fails. I tested the cd trying to install it on a virtual machine, and it seemed to work fine. So, it doesn't seem to be a problem with the disc.
Any ideas on what could be the problem?
Thank you
John
DL380 G3: http://h18000.www1.hp.com/products/quickspecs/11473_div/11473_div.HTML
The processors listed don't look like 64-bit processors. I couldn't find a solution for this kind of material. My workaround, however, is to simply continue using ESXi 3.5 on these and ESXi 4 on more recent/64-bit servers.
Note: If you found this useful, please consider to attributing points. Thank you!
-
Best practices to configure NLB for Secure Gateway and Web access
Hi team,
I'm vworksapce the facility and looking for guidance on best practices on NLB with webaccess and secure gateway. My hosted environment is Hyper-v 2012R2
My first request is it must be configure NLB, firstly that the role of set up or vice versa.
do we not have any document of best practice to configure NLB with 2 node web access server.
Hello
This video series has been created for 7.5 and 2008r2 but must still be valid for what you are doing today:
https://support.software.Dell.com/vWorkspace/KB/87780
Thank you, Andrew.
-
What are the best practices for creating only time data types, and not the Date
Hi gurus,
We use 12 c DB and we have a requirement to create the column with datatype of time only, if someone please describe what are the best practices for the creation of this.
I would strongly appreciate ideas and suggestions.
Kind regards
RanjanHello
How do you intend to use the time?
If you are going to combine with DATEs or timestamps from a other source, then an INTERVAL DAY TO SECOND or NUMBER may be better.
Will you need to perform arithmetic operations on time, for example, increase the time to 20%, or take an average? If so, the NUMBER would be preferable.
You are just going to display it? In this case, DAY INTERVAL in SECONDS, DATE or VARCHAR2 would work.
As Blushadow said, it depends.
-
VMware ESXi 4.1.0 and snapshot problem - no disk space
Hi all
We now have a big problem with our free space on the disk. We are using VMware vSphere (vSphere Client ver 4.1.0 and VMware ESXi ver 4.1.0):
Our vm has 2 HDD (500 GB, 1 TB). Now we have only 20 GB of free disk 1 and several snapshot files. To remove the snapshot, we need more than 20 GB of free space (corect?). What we need to do more free space? We can move snapshot files from the first disk to the second disk?
Thanks for any help
concerning
Dragan
First of all, you can redirect your new snapshot on another store/disk as explained in this article "http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1002929".
Secondo, you can delete snapshot older and smaller but not all together as explained in this article by Duncan Epping "http://www.yellow-bricks.com/2008/01/07/delete-all-snapshots/."
Alex
-
Hello, I have install ESXi 3.5 U3 on a Hp Proliant 380.
I have created a virtual machine to Windows 2003, and when I want to install VMWARE TOOLS from Vmware Infrastructure Client, it does not install on the virtual machine vmware tools. Nor has received all messages from a Client Infrastructure and neither of the virtual machine.
Why could this happen?
Thanks in advance
NO.
The installation of vmware tools lies in an iso file, which is located on your host ESX itself and is mounted on the virtual machine when you click "install vmware tools".
Weather or not your host has a cdrom drive is not serious, you can always add a virtual cdrom drive to your guests and use iso files, or the cdrom drive on the PC that you are using the VI client from.
If you vm doesn't have a virtual cdrom drive, it can't mount the vmware tools iso, and you cannot install the vmware tools.
-
VMware ESXi 5.1 Installation repair
I have a 5.1 host that does not load. I'm trying to find how to fix the esxi installation 5.1. When I boot to the iso installation that was used, I'd expect a repair option.
Hello
You do not have an option of repair on ESXi. Once you start with Installation ISO. continue upwards and on the next screen, promt, you will be prompted with a startup message
found the existing VMFS partition found. you want to keep the partition, select Yes.
If you have the host as disconnected or no answer yet on the vCenter server take a screenshot of your host-network--.configuration guts to networking. You will lose
network config and the need to recreate the same. But you can save your data from VMFS partition.
Thank you
Avinash -
Best Practices for CF9 Server w/IIS Installation
I'm all new to coldfusion and would like some guidance on the installation location.
I have two two servers running IIS on WS2008. Server 1 is my main database running MS SQL2005 and Server 2 is my dedicated server.
I intend on developing Flash/CF builders from my PC. Looking for recommendations for the best configuration to install CF9.
Thank you
Kurt
I would also like to mention that you can understand how you plan to integrate systems if you plan to use one of the servers GIS that are out there.
-
Best practices of Vmware with Vstorage
Hello
I'm under the process of implimenting a virtulized with HP EVA CF based storage environment.
The Setup program that would be two esx/esxi hosts would be linking EVA 4400 and connect via FC HBAS on each host.
We have enteprrise licnese with us as well as the Cisco nexus switches. I'm uncomfortable with the configuration of the Nexus.
Need expert advice on a few quick questions;
1. should I keep the VM on a storage shared for vmotion etc. Yes, I think so.
2. how to get EVA configured for optimal performance. There will be 4 VM running on each host ESX/ESXI.
3. should there be separated by machine VM LUN on by hostor how this work.
4. do I need to use the grouping of NETWORK cards that I don't have two NICS for each host.
5. I don't have an idea on RDM. It's worth should be used? Under what scenarios it is used and what not?
Kind regards
Sushil
A quick google search returns the following doc, am sure that there are quite a few other resources that model-specific maybe you use:
http://h20195.www2.HP.com/v2/GetPDF.aspx/4AA3-3801ENW.PDF
BTW, yes the for loop will change the default psp for all the LUNS online. As I said, changing the default psp to your HOME will do as well, but requires a reboot...
Good luck!
-
Best practices for the use of the DPS and cloud logins creative?
Hi-
I did have a chance to respond to my question via Google... If there was a previous topic posted on the forum about it, my apologies.
We users of DPS Pro for several years now, and in the early stages of the evolution of our software to cloud creative teams. We always use the Pro DPS account to produce a monthly magazine for iPads, Android and Amazon devices, but I'm trying to understand how our connection CC and 3 different connections rendition DPS will play together.
Right now, we're on CS5.5, so when we publish to different renditions, we record and off the Folio Builder when we need to access each account:
Once we move to CC, I'll be connected to this account (for me, there [email protected])-who is also mentioned as having access administrator and DPS App Builder in the dashboard of the Administration of our account Pro DPS. DPS account
Is there a way to get my CC/DPS [email protected] connection to allow me to create renditions in the three accounts - magazine, magazine_droid, magazine_amazon - or I have to log in and out of the Folio Builder in InDesign CC to create these "renditions", as we do in CS5.5?
And if it affects my CC updates somehow to log in and out of all these accounts?
Thank you in advance for your help!
Kristina
Your journal in the constructor of folio and your journal in CC are separated.
-
OBIEE installation and deployment on AIX
Hi Experts,
I installed OBIEE 10.1.3.4 on IBM AIX 5.3 (full installation with oc4j). Now how can I deploy the application which had Windows, I could choose the url for the presentation of the services and send it to the customer by which he could access the respective areas. But in AIX, after completing the installation, I do not know how to proceed (may sound silly, but you please forgive me... new in OBIEE... :)))
Help and advice needed!
Thank you
AKThe URL will be exactly the same as a Windows installation, but will have the name of your Unix server. You will need to learn how to start and stop services OBIEE and OC4J on Unix. It's pretty well documented on the Installation of the Infrastructure and the Configuration Guide.
-
Adobe Design Premium CC 2015 silent installation and deployment to mac machines
Hello
We started working on the tool suite casper to create packages and deploy them to silently mac machines. We use the composer tool to create packages. Our standards to deliver .pkg as end of the deliverable.
Adobe Design Premium 2015 CC / cc Photoshop 2015/cc standard design 2015 request received for packing and it is large.
Please let me know how to package for computers on mac with the help of composer or a better way to deploy this application to end users in silent mode? Please help me.
Thank you
lherault
You can use the creative Cloud Packager tool to build a pkg for distribution.
For more details on deployment with Caspar, see the white paper at technical documents | Resources | JAMF Software
-
Best practices of ESXi.
I'm trying to find out if I implement best practices correctly on ESXi 4.1 U1. Our facility has two on-board NICs and a quad card NETWORK to use for data and management networks. We have fiber for the side storage. If I understand the latest practices should I trunk 6-port then use port groups to manage traffic VLAN where going.
My question is this does not put excessive pressure on the network card that is used for the traffic of vmotion/vmkernel? If I put the switchport in one VLAN specific datagrams wouldn't get inspected and abandoned by the switch asics as opposed to the ESXi host to have to deal with them? I don't know if traffic would have a significant impact, so be it, but wanted to check before the implementation...
Thank you
FroggyI guess that you are concerned about air on the ESXi host performance, because it must deal with VLAN tags.
Don't worry about this. The overhead is minimal and modern NICS also have material unloading of functions for VLAN that will be used by ESX in many cases of handling.
However, remember that you have no safe the uplinks on the physical switch! Just create a virtual switch and add all the rising physical their. ESXi them then use all function of the active/standby/unused attribute that you can set by group of virtual ports.
Andreas
-
Best practices for vsphere 5.1
where can I find the doc more up-to-date about berries EQL configuration / best practices with vmware vsphere 5.1
Hello
Here is a link to a PDF file that covers best practices for ESXi and EQL.
Best EqualLogic practices ESX
en.Community.Dell.com/.../20434601.aspx
This doc mentions specifically that the storage Heartbeat VMKernel port is no longer necessary with ESXi v5.1. VMware has corrected the problem that made it necessary.
If you add it to a 5.1 system it will not hurt. It will take an IP address for each node.
If you upgrade 5.0 to 5.1, you can delete it later.
Here is a link to VMware which addresses this issue and has links to other Dell documents which confirm also that it is fixed in 5.1.
Kind regards
Maybe you are looking for
-
HP5746: Hp5756 uninstalled after Mac/Sierra updated and won't reinstall
I'm trying to help my mother who lives away from me. She upgraded the OS to Sierra today and can't get the HP5746 to work. Apple helped his printer delete or it has been deleted, but now she can't reinstall. She tried to reinstall the printer driver,
-
Get rid of "Star" "top apps" and categories on my main screen
When I go on my main screen, I have a banner with the recommended items. I see as 'best new games' how to simplify my screen?
-
Re: Tecra M9 - Clean install XP SP3 - sound doesn't work do not
I installed XP SP3 on my M9 from scratch, all the drivers are loaded and my device manager, says it all is hunky dory, but sound does not plug headphones or loudspeakers. I reinstalled the Realtek drivers a couple of times now but still nothing. Help
-
Satellite A300: Polish character does not appear using hotkey with 'c '.
Hey,. I am user of Toshiba Satellite A300 and early on, I discovered that there the combination Alt + C assigned to commissioning ATI - Catalyst Control Center. Unfortunately this combination should normally produce Polish characters 'Â' (it seems no
-
New Envy 15-j171nr running Windows 8.1, all the patches applied, including an update of the HP recommended BIOS. Only other change of important configuration, I've done was to enable virtualization in the BIOS (necessary for the required software an