BIOS Flash Utility fails with "BIOS directory is not found."

Similar Questions

• LoadPanel fails with error-94 file not found code unless I am in debug mode

  I've written a dll that has a number of panels in a .uir file.

  When I have it, debug using "debug SeqEdit.exe", everything works fine.

  But, if I just use "run SeqEdit.exe" (without debugging and using the same sequence file, I get the error message:)

  "Error in the call to LoadPanel.

  Handle of parent of Panel: 0,

  The IUR filename: HiPot.uir.

  Resource Panel ID: 4.

  Error code:-94

  File not found. "

  The IUR file is always in the same place, the only difference is that I do not use the debug option.

  It's probably something simple I've forgotten?

  You should not use LoadPanelEx in this case?

• Booting from a flash drive fails with a message: operating system not found

  I tried to boot from a flash drive, but it says operating system not found. Is there something wrong, that I did? I used a program called ISO on USB and he managed to copy the installer of Ubuntu on my flash drive.

  As you try to install a Linux operating system, I recommend you this announcement in a Linux forum. Not many people on these forums will be familiar with the installation of LInux.

• Storage migration fails with the error: could not complete the network copy to path to the file

  Hello

  I have two hosts ESXi 5.5 with local storage and VMware vCenter device which manage them. Everything worked well until that time.

  Now when I try to make the host migration and storage, processing or power off the virtual machine, I get the error message:

  Could not complete the network for file /vmfs/volumes/.../path/to/file.vmdk copy

  The situation is the same when I try to deploy VM on ESXi-2 model that is on ESXi-1.

  All with the network configuration is correct. I have ping between the hosts on ESXi and ESXi and vCenter. No firewall hosts ESXi and vcenter. No physical firewall between hosts.

  The network latency is less than 1 ms. No packet loss.

  I read this VMware KB article: Storage migration fails with the error: could not complete network file copy and I tried solutions explained here, but the results are the same.

  You have ideas where the problem may be?

  Hello guys,.

  I finally found the problem.

  ESXi servers are configured with MTU 9000, but the switch where the hosts are connected was a bug documented with frames. I found the problem after finding this article http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1003734

  I run the command of ESXi-1:

  vmkping - d-s 8972 192.168.10.12 where 192.168.10.12 is the ip address of ESXi-2

  The result was:

  3 packets transmitted, 0 packets received, 100% packet loss

  as a workaround, I reduce the MTU to 1500, then I patched the problematic switch.

• system failed because iertutil.dll was not found.

  When you start windows xp pro starts then stops and says this application has failed because iertutil.dll was not found.

  When you see a message like this:

  Explorer.EXE - unable to locate component: this application has failed to start because iertutil.dll was not found. Reinstalling the application may fix this problem.

  It is in the case Log:

  Event type: Information
  Event source: Application Popup
  Event category: no
  Event ID: 26
  Date: 18/02/2010
  Time: 08:38:48
  Description:
  Application popup: Explorer.exe - Unable to locate component: this application has failed to start because iertutil.dll was not found.  Reinstalling the application may fix this problem.

  The iertutil.dll file is required for explorer.exe at startup.  If explorer.exe is not able to run, you will not be able to do much with your system until the file is replaced.

  The file may have been deleted accidentally, malicious software could have deleted or your anti-malware software could have been quarantined it thinking it was a threat.

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  First of all, here are all the things you can 'try' which do not work:

  sfc/scannow

  The iertutil.dll is not one of the files that are protected by Windows File Protection, so it will not be replaced automatically if it's missing 3498.  This means that sfc/scannow won't help you.

  It is also not on your XP installation for you CD to copy or develop.

  You will have the same problem trying to start in any Safe Mode.

  You will not be able to run a browser on the system afflicted to go on Internet download one.  There is also a computer big security risk when downloading files from Internet sites anyway.

  You can still use the Task Manager to run the system restore and back, but I've never tried.

  If iertutil.dll is missing, you can copy from a system that works in the system afflicted with the same version of XP and Internet Explorer or sometimes copy one from another location on your system.

  You can get a good copy and put it on a floppy disk, thumb drive etc and copy it to your system plagued by using Manager tasks.

  When you see the error, you can click beyond it and eventually arrived at your screen background image where you can press CTRL-ALT-DEL to start Task Manager. TM you can click file, new task, browse and edit the menu drop-down "Files of type" to all files that you can see all the files in all the folders.

  Browse/navigate to c:\windows\system32 if iertutil.dll is really missing. If the error appears again while browsing, click OK to get past it.  The explorer.exe tries to run and cannot until the missing file is replaced.

  Then, still using the Task Manager, go to the c:\windows\system32\dllcache and see if there is a copy of the file.

  If this isn't in c:\windows\system32\dllcache, it is going to be elsewhere on your system and you will find another way.
  Start by looking in c:\windows\system32\dllcache.

  If it's the only thing missing, you can just copy the file to the c:\windows\system32\dllcache and paste it into c:\windows\system32 where it belongs.  If you don't, get one from a working system of the same type as yours, copy to a Flash DRIVE or a floppy disk and always using TM, browse, copy and paste it where it should be.

  TM, you can always access your thumb or other media same diskettes by navigation, copy, paste, etc. all work fine.

  You use TM to navigate to your thumb or floppy disk, copy the iertutil.dll good and then paste it in the c:\windows\system32 folder, where it is supposed to be.

  When go you there once again, your system may still be affected so no matter what you use for malware protection.
  follow these steps:

  Download, install, update and do a full scan with these free malware detection programs:

  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  It can be uninstalled later if you wish.

  Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• After my computer will crash does not start has a black screen with message operating system not found. Responsible for recovery disc but wont start.

  not boot Vista after that computer crashed have a black screen with message operating system not found.recovery discs won't load

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  Above is the way you normally boot from the Vista recovery disks.

  If you have tried to boot from the recovery without success disks, contact the manufacturer of your computer.

  This isn't their recovery process, Microsoft.

  See you soon,.

  Mick Murphy - Microsoft partner

• When I look for a file in Win Explorer, I get a list of files in the search results. But some of the files seem to be missing. I get a message that the directory is not found when I try to open the search results.

  I wonder if what's on my hard drive and if what Win Explorer is on my hard drive are two different things.

  If I do a search in Win Explorer to "purple", I get a number of results.
  (To search for a file, I am in the word "Purple" in the search field in the upper right Win Explorer and pressing the "Enter" button).

  There are a couple of JPG files that I wonder about the search results.
  One example is called "purple_flowers.jpg".
  When I double-click this file in the search results to open it, my paint program opens and gives me a message that the directory is not found. If I use MS Paint to try and open it by double-clicking on the file and selecting "open with...". MS Paint", I get a message that the directory is not valid.

  The location of the directory on the error message is the blue 'Images' folder for my user. But, when I opened this file, I don't have a file with that name in this directory. The same thing happens with another JPG file, called "octopus.jpg" when I search the word 'Octopus '.

  Is this something messed up between what I have on my hard drive and think what Win Explorer is on my hard drive?
  How can I fix?
  Something must be reset in Win Explorer?

  I could have the JPG files with these names at the same time. I had a large library of images for a project, but I deleted it.
  (I tried to turn on the option to show hidden files in this directory, but that did not help).

  Imane:

  I thank very you much for that answer.
  But it seems to have stumbled on the solution:

  Strangely, this worked:

  (Maybe you know why).

  I moved the files in my blue images folder in another folder, delete the folder images blue, emptied the Recycle Bin and rebooted my computer.
   
  When my computer has finished its startup routines, my folder of photos blue was there! And he had the shortcut to the folder 'Sample Pictures' inside.
   
  When I searched "the Octopus" and "purple", I no longer saw these JPG files in the search results.
   
  I don't really know what happened, but I thought that after these results just in case someone else knows this.

  I'll read and watch in your information. I don't want to know more about what is happening in my computer.

  Marz

• Failed to start Windows 7, not found Boot Manager?

  I have a Sony Vaio VGN-SR26GN with Windows 7 32 bit installed.

  He froze, ctrl + alt + delete does not work I turned it works but it was not able to start windows, all I ended up with is a black screen with cursor mobile, even with safe mode.

  I tried recovery, known last good configuration, etc... but nothing has worked

  Then I started getting the blue screen of death with the BOOT MANAGER NOT FOUND or something of the sort

  I tried to use the CD to repair windows 7 but it couldn't detect any installation of windows or another partition... I tried the bootrec different commands but nothing worked

  Now when I turn on the computer, it will start the Vaio repair utility, open a blue screen and nothing happens for hours.

  I don't know if it is a hardware or software problem. What else can I try to do?

  Thank you

  Hello

  References to Vista also apply to Windows 7.

  It is a serious mistake and "may" not be fixable without a professional technical support
  a real computer store (not the leeks and the glances at a BestBuy or other BigBox stores) or your
  Support of the machine system.

  Sony - Contacts
  http://eSupport.Sony.com/us/Perl/contact-land.pl

  Sony - drivers
  http://eSupport.Sony.com/Perl/select-System.pl

  Sony - Support
  http://eSupport.Sony.com/

  ---------------------------------------------------------

  This is the troubleshooting methods to try to resolve the problem:

  Try the Startup Repair - (if at anytime, benefit you from some, but not full access coming to Windows
  return and then try to startup repair.)

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  Try the disk Options recovery or Windows 7 startup repair.

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  Recover the Vista or Windows 7 bootloader from the DVD
  http://NeoSmart.NET/wiki/display/EBCD/recovering+the+Vista+bootloader+from+the+DVD

  Recovering the Vista Bootloader with EasyBCD (Windows 7)
  http://NeoSmart.NET/wiki/display/EBCD/recovering+the+Vista+bootloader+with+EasyBCD

  Fix the Vista Bootloader of Windows (Windows 7)
  http://NeoSmart.NET/wiki/display/EBCD/repairing+the+Windows+Vista+bootloader

  ------------------------------------------------------------

  Unable to boot into windows vista-windows boot configuration data file is missing required
  information - Repair Corrupt Boot Manager (Windows 7)
  http://www.troublefixers.com/unable-to-boot-in-Windows-Vista-Windows-boot-configuration-data-file-is-missing-required-information/

  How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and
  problems starting in Windows Vista (Windows 7)
  http://support.Microsoft.com/kb/927392

  How to fix "BOOTMGR is missing" in Windows Vista (Windows 7)
  http://cyberst0rm.blogspot.com/2007/04/how-to-fix-Bootmgr-is-missing-in.html

  Error message when you start Windows Vista: "the Windows Boot Configuration data file is.
  missing required information"(Windows 7)
  http://support.Microsoft.com/kb/927391

  Vista tip: Fix error "BOOTMGR is missing" - a quick way to (Windows 7)
  http://Lifehacker.com/251733/Vista-tip--repair-Bootmgr-is-missing-error

  See this article here - to repair/rebuild the Boot (Windows 7) Bootrec.exe tool configuration data use
  http://www.Vistax64.com/tutorials/163304-dual-boot-using-free-partitioning-software.html

  =========================================

  If you do not have a Windows 7 disc, you can borrow a friends because they are not a copy
  protected. The manufacturer of your system will also sell the physical DVD cheap since you already
  Clean Windows. You can also do an ERD on another computer.

  If you need to repair disks - these help repair Windows not re-install.

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• the output directory is not found

  I get "the output directory is not found. Please update and try again. "I want to just post my host and I get the dialog box. I recorded it in different places and I always get the dialog box. What can I do?

  It was recorded in the folder called with ' / ' has changed to '_' and now I can publish, so weird. It didn't happen with edge of adobe. Is it possible to apply acceleration and on board where we had a couple of options with the click of a button?

• Photoshop CC: Save for Web - the file or directory is not found.

  I have Photoshop CC installed on a Mac laptop and everything works fine. I recently installed Photoshop CC on my iMac and when I try to save for Web, I get the error "the file or directory is not found." ...

  As far as I know, all parameters are the same as they are on my laptop. This file is not found? Where do I get it? I tried to uninstall Photoshop CC and reinstall, but that solves nothing.

  OS X 10.9 running on two computers

  I found my problem. I moved the folder my documents on a faster HARD drive and had it mapped with this player yet. I deleted the files preferences related to save for web, but they did not help so I went he tracks farther and that's what I found for my problem (even though Photoshop is configured to use a RAID as a scratch disk.

  Thank you

• I downloaded Adobe photoshop cs 5, after download, it is not installing in my computer of OS - Windows 7 and the message is to give "Installer failed to initialize. File not found. Download Adobe support Advisor to check the problem

  I downloaded Adobe photoshop cs 5, for trial, after download, it is not installing in my computer of OS - Windows 7 and the message is to give "Installer failed to initialize. File not found. Download Adobe support Advisor to check the problem

  just uninstall cs5, clean a cleaning use of the CC tool to resolve installation problems. CC, CS3 - CS6 then install.

  Make sure your file is downloaded to your hard drive sizes are expected file sizes.  If you don't know how, ask someone to do it for you.

• Installation of VMWare Workstation 11.1.0 on Win 8.1 is THAT MSI will fail with the error "could not write value vmware - tray.exe for \software\microsoft\windows'currentversion\run-cles.

  Hi all

  The MSI failed with the error message as "could not write value vmware - tray.exe in \SOFTWARE\Microsoft\Windows'CurrentVersion\Run key.  Make sure you have fufficient access to that key, or contact your support staff' while trying to install vmware workstation 11.1.0 in windows 8.1.
  I tried to call the installer with run as administrator but it does not help, please suggest me overcome this error.

  Hi Vincentand welcome to the VMware communities!

  This error indicates that you have some security software (antivirus or antimalware software) that protects the part of the registry.  Can you try to temporarily disable all security software on your host computer and see if the installation can move forward?

  See you soon,.

  --

  Darius

• Single Sign on authentication failed with error [user: username is found, but]

  Hello
  
  URGENT:
  
  One user is trying to connect to Essbase by Excle worksheet. To connect in Essbase, this user who connects to the network using the VPN connection. I suspect that this question arises because of an invalid password, but the user claiming that password is correct. When I checked the user information in Essabase, he gave an external authentication that is valid.
  
  Please help me on this issue. What should go wrong with this user?
  
  * Single Sign on authentication failed with error [user: username found, but could not authenticate] *.
  
  Thanks again for your help.
  
  Kind regards
  UB.

  If essbase uses an external authentication as MSAD, you can get the password changed at the level of the AD by someone who takes care of the administration.

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• Try to install the downloaded drivers when comes up with the error "file not found".

  Downloaded the drivers Vista for the HP Photosmart premium C410b and installation of hen comes up with the following error message: file not found

  C:/program files/hp C1164EDO-EF08-4B0B-8085-3BDSEAAEFD8D} \gup\at. Any ideas?

  Hi daddums1958,

  Try using the brush included in the CD or download.

  Of the Original installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5. run the L4uninstall.exe

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-84595-1&CC=US&DLC=en&LC=en&os=2093&Product=4186830&sw_lang=

  10. run the download to reinstall the printer

  If the software has been downloaded and extracted to your system:

  1. type % temp % in the field of race

  2. Locate and open the folder starting with 7z (example: 7zS2356)

  3 open the Util folder

  4 open the CCC folder

  5. run the L4uninstall.exe

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-84595-1&CC=US&DLC=en&LC=en&os=2093&Product=4186830&sw_lang=

  10. run the download to reinstall the printer

• valid no directory is not found

  Hello

  I got an error "warning: no valid directory could be found."

  Wich error am I doing?

  Garry

  "From there I going to acrobat.com".

  When you use digital publication tools, there is no reason to use acrobat.com. It works at the moment, but it is not supported.

  Use the sharing feature in the Folio Builder Panel to share the folio with other users. But first, get a glimpse of the folio to ensure that you do not have mixed directions or added different items sizes that would prevent the folio to preview.

  I don't know what is the origin of the "browser not supported message. Can you provide a screenshot?