BitLocker, configure the module TPM after encryption.

Similar Questions

• Configure the module of firepower ASA IP address

  Hello

  today I tried to configure the IP address of the late ASA power module. But unfortunately I failed. The firewall is in the direction of the situation and also do have not any router on the LAN. So, I stop the management interface and configure the IP of firepower on the network server management. But unfortunately I can not ping the gateway IP address that is actually one of the interface of the firewall. It is the series x 5525 firewall. So this isn't a any interface dedicated to management of firepower. It would be nice to know where I made the mistake? I recharge and recovery of the module and I consider the State as always state of recovery. So my question is looking for there is a problem with the module itself?

  Module status

  SH module

  Model serial number of map mod
  ---- -------------------------------------------- ------------------ -----------
  0 ASA 5525 - X with SW, GE, 1 GE Mgmt, AC 8 data
  IPS unknown n/a
  cxsc unknown n/a
  SFR unknown n/a

  MAC mod Fw Sw Version Version Version Hw address range
  ---- --------------------------------- ------------ ------------ ---------------
  0 f  1.0                                                2.1(9)8      9.2(3)
  ips                                                         N/A          N/A
  cxsc                                                       N/A          N/A
  sfr                                                         N/A          N/A

  The Application name of the SSM status Version of the Application of SSM mod
  ---- ------------------------------ ---------------- --------------------------
  IPS unknown current Image number does not apply
  cxsc unknown No. current Image does not apply

  Data on the State of mod aircraft compatibility status
  ---- ------------------ --------------------- -------------
  0 to Sys does not apply
  IPS does not is not Applicable
  cxsc does not not Applicable
  SFR recover not Applicable

  Config firewall Interface

  #Interface IP-Address OK? Method State Protocol
  GigabitEthernet0/0 10.101.106.115 YES CONFIG upward upwards
  GigabitEthernet0/1 10.106.106.115 YES CONFIG upward upwards
  GigabitEthernet0/2 10.103.254.254 YES CONFIG upward upwards
  GigabitEthernet0/3 10.0.210.254 YES CONFIG upward upwards
  GigabitEthernet0/4 10.100.254.254 YES CONFIG upward upwards
  GigabitEthernet0/5 10.107.253.115 YES CONFIG upward upwards

  #interface GigabitEthernet0/1
  Speed 1000
  full duplex
  nameif Server
  security-level 70
  IP 10.106.106.115 255.255.0.0

  Fire power management configuration

  Host name: 1 Swiss francs
  Configuration Management Interface

  Configuration IPv4: static
  IP address: 10.106.251.253
  Network mask: 255.255.0.0
  Gateway: 10.106.106.115

  IPv6 configuration: Stateless autoconfiguration

  Configuration of DNS:
  Domain: XXX.local
  Search:
  XXX.local
  DNS server:
  10.101.251.2
  10.201.251.2

  Any help will be greatly appreciated.

  Thank you

  Sari

  Sari,

  Even if there is not a physical module services fire power management port, it uses Management0/0 port to connect to the module of SFR.  If you like on the same VLAN as your server VLAN on the SAA plug Management0/0 port on a switch that is sharing the network server VLAN and give the module SFR an IP address on the same subnet.

  Make sure that you remove the statement under interface Management0/0 nameif. Here is an example:

  interface Management0/0
  management only
  No nameif
  security-level 100
  no ip address

• Marshmallow stuck on the boot loop after encryption

  Hello! I have improved my motorcycle G 2nd Gen to Marshmallow Friday. Today, I chose the option to encrypt my phone for security reasons, and once I chose the model and it restarts, it is stuck on the boot animation. Unlocking scheme but then returns the boot animation shows and pass. After more than 4 hours, I tried to enter the quick recovery and it says that the device is locked. I have tried factory reset without the quick recovery result. If I turn off the phone it boots on its on and so on and so forth.

  The model is XT1068.

  Activation of the encryption on the 2nd Gen Moto G is not a good idea, unless you are really paranoid. It's too slow as the CPU supports a few commands that deal with some of the encryption at the hardware level.

• Configure the application server after you change the database

  Dear all,

  We use ORACLE EBS R.12.1.2. Database: 11.1.0.7. 2 RedHat linux servers.

  We are validating failover scenarios keep oracle database data.

  Scenarios is that; We fail on the primary database and primary database role has opted for sleep.

  Should what changes we make on the Application Server?

  Should we change configuration of application server to connect to the new database (name, address of db server... etc). and how?

  Thanks in advance,

  Shareef

  PL see Section 6 in MOS Doc 1545920.1

• Develop the module problem after upgrade to LR6

  I upgraded from LR4.4 to 6, but had made a stop at 5.7 on the way. I have improved the catalog to v5.  Now in LR6, that I bought at the end of the day, photos in the develop module are corrupt. I can see them but are mainly grey with a few colourful highlights. Don't know if it's a question of catalog or how to fix. All files seem to be affected!

  Hi cruizemissile,

  Please turn off the graphics processor in the Lightroom preferences.

  Open Lightroom

  Go to Lightroom preferences in the Edit menu

  Click the performance tab

  Deselect the graphics processor

  Restart Lightroom

  Let us know if that helps.

  Kind regards

  Mohit

• Defining the name of the module in the program of the OIC

  Hello
  
  I was struggling with defining the name of the module in my OIC program. Here's the code in which
  I create the environment, connect, try to set the module attribute, wait for the Enter key and clean
  and exit after completing the Enter key.
  
  I can say, I called OCISetAttr as the documentation says I should, and none of my return values
  indicate a problem. Yet, when I v $session, I get what I assume is the default value of the module
  and no value, I put in the code ("moduletest").
  
  The physical file name programs is oci101.exe. It also connects to the Oracle instance as a named user
  oci101. I check v$ session with this query:
  Select the user name, the module from v$ session where the username is not null;
  
  And the output is as follows:
  
  USER MODULE NAME
  ------------------------------ ------------------------------------------------
  OCI101 oci101.exe
  SQL SYSTEM * more
  
  I see a column value 'moduletest' for the OCI101 user MODULE.
  
  Don't know what I'm missing. Any ideas? Here is the code:
  
  Code BÉGIN:
  
  OCIEnv * envhp;
  UB2 charset_id = 0;
  UB2 ncharset_id = 0;
  UB4 mode = OCI_DEFAULT;
  
  sword env_rc = OCIEnvNlsCreate () const
  & envhp, mode,
  (void *) 0, / / context for the allocation of memory to custom user defined
  (void *) (*) (void *, size_t) 0, / / malloc user defined
  (void * (*) (void *, void *, size_t)) 0, / / realloc user defined
  (void (*) (void *, void *)) 0, / / / / free user defined
  (size_t) 0, / / off user memory
  (void *) 0,.
  charset_id, ncharset_id
  );
  
  OCIError * errhp;
  sword err_rc = OCIHandleAlloc () const
  (dvoid *) envhp, (dvoid *) & errhp,.
  OCI_HTYPE_ERROR (size_t) 0, (dvoid *) 0
  );
  checkerr (err_rc, errhp);
  
  OCISvcCtx * svchp = 0;
  sword l2rc = OCILogon2 () const
  envhp, errhp, & svchp,
  (const OraText *) zusername, (ub4) strlen (zusername).
  (const OraText *) zpassword, (ub4) strlen (zpassword).
  (const OraText *) zdatabase, (ub4) strlen (zdatabase).
  mode
  );
  checkerr (l2rc, errhp);
  
  Define the attrbute module
  Extract the session descriptor in sessionhp.
  
  OCISession * sessionhp = 0;
  UB4 sh_size = 0;
  sword oci_attr_get_status = OCIAttrGet (svchp,
  OCI_HTYPE_SVCCTX,
  & sessionhp,
  & sh_size,
  OCI_ATTR_SESSION,
  errhp);
  checkerr (oci_attr_get_status, errhp);
  
  Configure the module
  sword oas_rc = OCIAttrSet (sessionhp, OCI_HTYPE_SESSION,(void *) 'moduletest',
  strlen ("moduletest"), OCI_ATTR_MODULE, errhp);
  
  checkerr (oas_rc, errhp);
  
  GetChar ();
  Cleaning:
  If (svchp) {/ / 0 when already disconnected}
  OCISvcCtx * const tmp_svchp = svchp.
  svchp = 0; reset the svchp error or not
  const sword lorc = OCILogoff (tmp_svchp, errhp);
  checkerr (lorc, errhp);
  }
  
  sword const rc = OCIHandleFree (envhp, OCI_HTYPE_ENV);
  End of the Code.
  
  Thanks for any help...
  
  Karl

  Hi Karl,

  I'm certainly not an expert of BEAK, but after you set the module attribute, the value is updated when the next execution of the statement in my experience. There may be other ways in which this can happen, but I have not seen such cases.

  Here is a short example:

  #include 
  #include 
  #include 
  #include 
  
  int main(int argc, char *argv[]) {
    OCIEnv      *envhp = NULL;  /* OCI Environment handle     */
    OCIError    *errhp = NULL;  /* OCI Error handle           */
    OCISvcCtx   *svchp = NULL;  /* OCI Service Context handle */
    OCISession  *usrhp = NULL;  /* OCI User Session handle    */
  
    OCIStmt     *stmtp = NULL;  /* OCI Statement handle       */
  
    /* the statement to execute   */
    /* this is purely for example */
    oratext *sqlstmt = "begin null; end;";
  
    /* connection information */
    oratext *username = "scott";
    oratext *password = "tiger";
    oratext *database = "orademo";
  
    /* used to hold the results of each OCI call */
    sword result = 0;
  
    /* Initialize and create a default environment */
    result = OCIEnvCreate(&envhp,
                          OCI_DEFAULT,
                          (dvoid *) 0,
                          0,
                          0,
                          0,
                          (size_t) 0,
                          (dvoid **) 0);
  
    /* allocate an error handle */
    result = OCIHandleAlloc((dvoid *) envhp,
                            (dvoid **) &errhp,
                            OCI_HTYPE_ERROR,
                            0,
                            (dvoid **) 0);
  
    /* create connection */
    result = OCILogon2(envhp,
                       errhp,
                       &svchp,
                       username,
                       (ub4) strlen(username),
                       password,
                       (ub4) strlen(password),
                       database,
                       (ub4) strlen(database),
                       OCI_DEFAULT);
  
    /* get the user session handle */
    result = OCIAttrGet(svchp,
                        OCI_HTYPE_SVCCTX,
                        (void *) &usrhp,
                        NULL,
                        OCI_ATTR_SESSION,
                        errhp);
  
    /* set the module attribute */
    result = OCIAttrSet(usrhp,
                        OCI_HTYPE_SESSION,
                        (void *) "My Module",
                        (ub4) strlen("My Module"),
                        OCI_ATTR_MODULE,
                        errhp);
  
    /* allocate the statement handle */
    result = OCIHandleAlloc((dvoid *) envhp,
                            (dvoid **) &stmtp,
                            OCI_HTYPE_STMT,
                            0,
                            (dvoid **) 0);
  
    /* prepare the statement for execution */
    result = OCIStmtPrepare(stmtp,
                            errhp,
                            sqlstmt,
                            (ub4) strlen((char *) sqlstmt),
                            OCI_NTV_SYNTAX,
                            OCI_DEFAULT);
  
    /* execute the statement - after execution the */
    /* MODULE value should be updated in v$session */
    result = OCIStmtExecute(svchp,
                            stmtp,
                            errhp,
                            (ub4) 1,
                            (ub4) 0,
                            (CONST OCISnapshot *) NULL,
                            (OCISnapshot *) NULL,
                            OCI_DEFAULT);
  
    /* print a simple prompt    */
    /* view session in SQL*Plus */
    printf("program paused, ENTER to continue...");
    getchar();
  
    /* disconnect from the server */
    result = OCILogoff(svchp,
                       errhp);
  
    /* deallocate the environment handle */
    /* OCI will deallocate child handles */
    result = OCIHandleFree((void *) envhp,
                           OCI_HTYPE_ENV);
  
    return OCI_SUCCESS;
  }
  

  When the program is paused I see this in SQL * more in my test:

  SQL> select sid, username, program, module from v$session where username = 'SCOTT';
  
         SID USERNAME         PROGRAM                          MODULE
  ---------- ---------------- -------------------------------- --------------------------------
         136 SCOTT            OCIModuleTest.exe                My Module
  

  Maybe it's a little help.

  Kind regards

  Mark

  Published by: Mark Williams on December 22, 2008 11:06

  Put a little sample.

• I have hp elitebook 8440p, I inserted the sim card, but I'm not able to see where to configure the sim card

  Hi I have a hp elitebook 8440p but I did not; KWN how to use sim card option, I inserted the sim card, but now I can't see wher to configure the sim card or use, cos I m unable to see any option, so please help me

  Hello

  The HP EliteBook User guide contains information on what is required to configure the module top mobile broadband in your mobile workstation. Go to the HP Web site for more information about the configuration and activation of the SIM card.

• According to the journal of DDPE encryption starting not due to the fact that the the TPM Base Services (TBS) secure is not started

  Basic services of the title: original TMP (TBS)

  I'm running Windows 7 x 64 SP1 Enterprise Edition.  We use DDPE to manage BitLocker.  Laptops are not encrypted.  According to the journal of DDPE encryption starting not due to the fact that the the TPM Base Services (TBS) secure is not started.  Open services.msc and realized that TBS was not even as a service.  Research on TBS and found it's relies on the file "tbssvc.dll.  This file is not anywhere on my PC, (should be in Windows\System32).  I hope someone can help me with the following questions.  I'M assuming that TBS is a Windows service?  He would appear in a standard installation? Windows Update?  If it is standard, and it does not install, is there a way to reinstall the service?  I found a link on the Dell site that got copy tbssvc.dll from a work computer, paste it to a computer for non-working, create new registry keys and register the dll from the registry.  It works, but I prefer not to go down this rabbit hole if there is a simpler solution.  Thanks for your help.

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *

  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum
  
  
  If you give us a link to the new thread we can point to some resources it

• Windows cannot configure the Merge Module SOHlib

  error message at startup.

  original title: SOHLib Module.msi merge

  How to stop a message that happens every time I start the computer?

  The a of windows cannot continue.  SOHLib fusion Module.msi is not found.

  Then, another window appears that says: Error 1706 no valid entry was found for the product.

  Hi Alfonsos,

  Thanks for choosing Microsoft Community Forums.

  According to the description, it seems that you receive an error message "windows install cannot continue. SOHLib fusion Module.msi was not found"on startup.

  (1) did you do changes on the computer before this problem?

  Step 1: I would say as you follow the steps to start the computer in Mode safe and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  If the issue is not persistent, then follow the article to find the cause of the same thing.

  Step 2: I suggest you to place the computer in clean boot mode and check if the problem persists.
  A clean boot to check if startup item or services to third-party application is causing this issue.
  You can read the following article to configure the computer to boot:
  http://support.Microsoft.com/kb/929135
  Note: After the troubleshooting steps, see step 3 of the link to clean boot the computer to a normal startup mode.

  I hope this helps. Try the above steps and get back to us for further assistance if you have questions about the Windows operating system. We will be happy to help you.

• Hyperion Planning - invalid or did not find the configuration of the module

  Hello

  I modified the essbase property file in essbase server and report as server below and restart all the services of hyperion.

  netConnectRetry = 30

  netDelay = 2000

  netSocketTimeOut = 20000

  After restarting the services, I am not able to open planning applications. I get the error message - 'invalid or did not find the configuration of the module.

  Thank you

  Michel K

  This error is straight after the restart services, usually that type of error can be caused if the jdbc connection pool is full, which shouldn't really be the case when the service starts up.

  Are you able to connect to schedule directly if? If this isn't the case, restart the new service and check if the errors are recorded.

  See you soon

  John

  http://John-Goodwin.blogspot.com/

• Unable to start Portege S100 after the HDD with SafeBoot encryption

  I am trying to install the full encryption of the disk of SafeBoot (McAfee Endpoint) of 100 + laptops, which most is Toshiba. I use Device Encryption 5.1.5.0, liberation 5300 (515-0015) and I was able to install successfully on a number of different models of Toshiba, however, the Portege S100 causing me a problem. The customer of SafeBoot software installs OK on Windows XP SP2 (and SP3) and encrypts the drive as usual, but as soon as I restart it does not start again.

  Now, when I turn first I get:

  From SafeBoot v5.1
  Please wait...

  for a second, then a dialog box appears in the middle of the screen:

  SafeBoot error
  Error: 0xe002001b
  No boot disk was found

  He never does to SafeBoot screen logon is still in the start-up phase.

  I think it's because this laptop has a SATA RAID build controller. We do not use the RAID configuration and that you have an original disc installed. The BIOS is the latest version 1.50 and the third system configuration screen shows the status of RAID array to 1RAID-0. If I put it in JBOD so I can't even go as far as the Windows installation.

  So far I have tried to replace the Toshiba RAID with the Intel 82801FBM (ICH6M) driver SATA AHCI 7.0.0.1020 pilot. It works very well during the installation of Windows to step and F6 in Windows before encryption. I used even with the success of this pilot with a WinTech CD (updated the BartPE CD with SafeBoot plugin) and am able to see the encrypted drive. However, even with this driver, I get the same message once encrypted.

  I'm sure that my SafeBoot administration and deployment is configured correctly because the same works set of installation very well on a certain number of models different for laptop, but not this one.

  Any suggestion would be appreciated.

  Hello

  I m not an expert in SafeBoot software. It s I don't not known but I would like to say a few words about the RAID driver that you used.

  I think that it s a bad driver. It looks like a SATA driver and not the RAID driver.

  The Toshiba European page pilot provides a * 1.3.8.0 * v for the Toshiba RAID driver

  Please check this!

  I would recommend also consulted with the Portege S100 user manual.
  You will find details of the RAID.

  JBOD means no RAID settings. By using this option, Windows cannot be installed on this drive, except using the Toshiba DVD/CD product recovery

  Good bye

• Satellite P755 - 11G: Win 7 64 bit - cannot activate BT after replacement of the module

  Hello

  On my laptop Satellite P755, I had to replace the Wifi/Bluetooth PCI Express Mini card because the original Atheros was broken and was no longer working.

  So I decided to buy a new Intel® Wireless-Dualband-AC 7260 card to replace.
  Has successfully replaced by itself.
  WiFi now works again.

  Now, I'm dealing to get BT running. With the old Atheros card I could activate BT by pressing FN + F8 and choose Bluetooth from the menu of flashcard on top of the screen.

  After the replacement of the F8 full option in flash cards had disappeared.
  I managed to solve the problem for the WiFi by adding the ID of the new material of the card Intel (PCI VEN_8086 & DEV_08B1 & SUBSYS_40708086) in the registry in the following locations:

  HKEY_LOCAL_MACHINE\SOFTWARE\TOSHIBA\ConfigFree--> InternalDevice176
  Hotkey HKEY_LOCAL_MACHINE\SOFTWARE\TOSHIBA\Wireless--> DevID_SupportRL175
  HKEY_LOCAL_MACHINE\SOFTWARE\TOSHIBA\WirelessAPL\BT WLANDP--> DevID_SupportRL176
  HKEY_LOCAL_MACHINE\SOFTWARE\TOSHIBA\WirelessDevice ID--> DevID_SupportRL176

  Now FN + F8 works very well for the WiFi, flash cards menu appeared again.
  But there is still no option to activate Bluetooth.

  Addition of the BT hardware in the registry (same locations as the WiFI) ID does not help.
  I can't get the point how the flash cards software manages to activate the bluetooth normally.

  Does anyone have an idea what it takes to get the Bluetooth in the menu flash cards?

  My system:
  Toshiba P755 - 11G
  Windows 7 64 bit

  See you soon,.
  Alex

  Hello

  You said that the original WLan module was to Atheros.
  As far as I know the module Atheros WLan additional needs for the installation of the filter for the Atheros BT driver package in order to use and activate Bluetooth.

  In the case of modules WLan Intel such package of filter is not necessary.

  I guess the Atheros BT filter driver package is always installed on this laptop and I think this might be the reason why the BT can not be activated properly.

  However, I recommend you to uninstall the filter BT mentioned driver package as well as Toshiba BT stack, driver Atheros WLan and the Toshiba value added package, and the Flash Cards Support utility. Clean the system using the CCleaner tool.

  Then install the Intel driver that would control the new Intel WLan card.
  Install the Toshiba BT stack and restart the device. Now follow with the installation of the Toshiba added value package and the Flash Cards Support utility. Reboot once again and check if you can use FN + F8 to activate WiFi and BT

• It appears two times after the opening of Firefox ' [JavaScript error: 'dir is zero' {file: "file:///C:/Users/... and a new window opens each time."}] Opening of the modules in the Tools menu crashes Firefox.

  Whenever I open Firefox, or when a website automatically opens a new window (NOT when I open a new tab or window) error message is displayed twice: ' [JavaScript error: "dir is zero" {file: 'file:///C:/Users/Steve/AppData/Roaming/Mozilla/Firefox/Profiles/k8nfi7qa.default/extensions/%7B0538E3E3-7E9B-4d49-8831-A227C80A7AD3%7D/components/nsForecastfox.js' line: 323}] "when calling method: [ffIDiskService::get]"
  Then, after closing the window of mistake twice, an AnyColor start/welcome screen appears in a second, open tab, which I then close to resume with the first tab (active). If I try to open the modules in the menu Tools, Firefox crashes and a script error message. It then becomes "unresponsive" and I have to force - close Firefox and reopen.

  This looks like a problem with an add-on, especially the Forecastfox extension. To test this try to disable the add-on in safe mode, for details on how to see the extensions, themes and problems of hardware acceleration to resolve common troubleshooting Firefox problems.

• No option to simulate the peripheral cRIO after installing Labview and RT/FPGA Modules of downloads (lack of driver support?)

  Hi guys -.

  Basically, I need to simulate a cRIO device without yet having equipment on-site, like this:

  How to simulate the FPGA hardware target using with LabVIEW Project Explorer

  Instead, I only get the options presented in the attachment "Add Target Options.jpg.  I guess it's because of missing drivers, which I assume is due to an error that I made during a recent new LV installation installation went like this: I downloaded (not diskettes) and installed the following (in this order, the latest versions all around):

  (1) LabView development system

  (2) real-time module

  (3) FPGA module

  (4) NEITHER-RIO (previous installation-by-installation)

  (5) DAQmx

  At the end of (1) and (2), I got the screen shown in the second attachment ("Drivers Installer Message.jpg"), but could not able to recognize the folder "device drivers OR" (I also downloaded), or one of its subfolders.

  According to me, I'm missing an obvious option to load the necessary drivers after installation, but can't seem to find reference to it in the forums.  Could someone give me a little help in the right direction?

  Thanks a lot and have a nice day.

  
  

• After Encrypting files, I had to reinstall my windows and now I can not decrypt the file

  * O.T. > encrypted files

  So after encryption of files I had to reinstall my windows (changed the name of the owner) and now I can not decrypt the file

  After attempting to decrypt the files, I'm promped with this message:

  Attribute application error

  An error occurred applying attributes to the file:

  driveletter\filename

  Access is denied. \

  I want to say that I added my administrator name in the Security tab, and then gave me full control over the files, but that did not work.

  Hello

  I understand that you cannot decrypt files previously encrypted in Windows 7 after you have reinstalled Windows.

  • What program did you use to encrypt the files?

  From now on, I would ask you to refer to similar questions discussed in the thread below links and check the status.

  Cannot decrypt previously encrypted files

  I'm unable to decrypt files encrypted after reformatting the hard drive.

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.