Blank Screen when start Windows normally

Similar Questions

• Start & restart time is 5-6 minutes - Blank screen when starting the process.

  1. Every time I have start or restart my computer and I timed several times he and average is 5.5 minutes. It's the sequence of events;
  2. Start or restart
  3. Computer stops
  4. HP will appear instantly
  5. Scaning of Windows bar
  6. Appearance of Windows Logo
  7. A black screen with cursor and last minute 1.75
  8. Desk top of page icons appear so quickly, followed by the taskbar
  9. Then the sidebar (which I stopped during startup and the time was not performed)
  10. The last item to start is Kaskresky Internet Security 2010 and restart its not updated
  11. I don't think I have too many start up programs
  12. A Geek Squad agent told "he disobeys in safe mode, which suggests that it is a problem with the software loaded on the computer.
  13. Any ideas on this one?

  Thank you for your time & consideration... Celestyna

  Hi Celestyna,

  It is possible that some element of start-up or third-party program installed on the computer is at the origin of time start delay.
  I suggest you perform the clean boot procedure and check.

  To help resolve the error and other messages, you can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Perform the check and the clean boot if you have the problem.

  1. click on start, type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or a confirmation, type the password, or click continue.
  2. in the general tab, click Selective startup.
  3. under Selective startup, clear the Load Startup items check box.
  4. click on the Services tab, select the hide all Microsoft Services check box, and then click disable all.
  5. click on OK.
  6. When you are prompted, click on restart.
  7. after the computer starts, check if the problem is resolved.

  If the problem is resolved to check what is the cause of the problem, referring to the link given below:
  http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual
  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  Click Start, type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  On the general tab, click the Normal startup option, and then click OK.
  When you are prompted to restart the computer, click restart.

  Optimize Windows Vista for better performance
  http://Windows.Microsoft.com/en-us/Windows-Vista/optimize-Windows-Vista-for-better-performance

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• After a power cut my PC is in a loop in the start windows normally, safe mode, last known good configuration screen

  After a power failure when I start my PC, it gets to the screen... "We apologize for the inconvenience, but windows did not start successfully... When I try to reboot in one of the 5 modes to start normally, safe mode, safe mode with command prompt SafeMode with network, last known Noah correct configuration of their work and the loops of the computer to this sreen repeatedly.

  KB307545 is a very bad idea to begin with - especially after a power failure (and it's usually just a very bad idea).  You don't describe symptoms suggestive of a need to run the KB307545, but, I'm not a Microsoft Support engineer so don't hesitate if you are forced to do, and I wish you good luck.

  What you need to do, is start in the XP Recovery Console and run chkdsk/r first.  Is is possible that the blackout damaged your NTFS file system and a chkdsk/r is to clean it.

  Provide information on your system, the better you can:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?

  Sometimes, when XP has a problem starting or falls down and tries to start again, it will give you a "short" menu of boot options and none of them will appear to be good to get your system going again.  You have tried them all!

  The options are similar to the Advanced Boot Options menu XP, but the only option that you need (disable automatic error system reboot) are not offered, because XP went too far during the boot process and offers a limited number of boot options.

  If this is the case, you must call Options menu advanced boot yourself until you do not see the option:

  Disable the automatic restart in the event of system failure

  When you get the XP Advanced Options correct start menu you want to see, he has options on it like these:

  Safe mode
  Safe mode with networking
  Safe mode with command prompt

  Enable Boot logging
  Enable VGA mode
  Last good Configuration known (your most recent settings that worked)
  Directory Services Restore Mode (Windows domain controllers only)
  Debug mode
  Disable the automatic restart in the event of system failure

  Start Windows normally
  Reset
  Return to OS Choices Menu

  You need to choose in this menu is the option:

  Disable the automatic restart in the event of system failure
  
  Then if XP does not start normally, you will see an error screen with information and clues about the problem and then you can decide what to do next.

  If you do not see the automatic restart on system failure option turn it off, you must reset your system and start typing the key F8 on the keyboard until you see her disable automatic restart on system failure option.

  If you miss the window of opportunity F8, you must try again and start tapping the F8 key with more urgency (earlier and more frequently) until you see disable automatic restart on system failure, and then select.

  You must keep trying the F8 menu until you see disable automatic restart on system failure option, and select it.

  If your system has a Blue Screen of Death (BSOD), we need to know what the screen says:

  Here's a BSOD example showing information you provide:

  http://TechRepublic.com.com/i/tr/downloads/images/bsod_a.jpg

  Send for the nose and the Red arrows (3 to 4 lines total).

  Send all * line STOP message since there are clues in the 4 parameters.

  If it looks like there is some kind of name listed in the STOP message file, send this line also.

  Ignore the boring text unless it seems important to you.  We know what a BSOD looks like, we need to know what your BSOD looks like.

  Answering queries and results report of the disable automatic restart on system failure screen and you can decide what to do next.

  See what the BSOD said would be interesting, but I would still recommend that you run chkdsk /r from the XP Recovery Console to make sure your file system is not damaged.

  Answer the questions and we can see what to do next.

• Crash stuck to repair or start windows normally screen.

  system was crushed, put off during a windows update. never had a problem before. Stuck repair (recommended or start windows normally screen.) How can I fix it?

   

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• my laptop keeps going to start page.__No regardless of which option to choose, that is to say. safe mode, safe mode, safe mode with command prompt, the last known good configuration, start windows normally, it's always the same

  my laptop keeps going to the start page. No matter which option I choose, IE. safe mode, safe mood with networking, safe mode with command prompt, last known, good configuration start windows normally, it always comes back to the same screen. saw this post before and the invloved boot cd solution. I have not a cd ROM is there another way to solve this problem. Thank you people

  Thank you for taking the time to make this post very informative, excellent. Without the machine test myself that I can't be sure, but based on the age of the computer and what you wrote I suspect for lack of material. It could be something simple like the hard drive or RAM or something more serious like the motherboard. I wouldn't recommend replacing any material on such an old laptop.

  As long as the hard disk has been physically, you can recover your data easily. If the hard drive has failed, then you will need to send the drive to a professional drive savers data recovery company. It is quite expensive ($500-3700), but they can usually recover your data. Some insurance policies cover also, professional data recovery in order to check with yours. But let's be optimistic. ;-)

  IMPORTANT - If there is no question that the drive is at fault - there are noises, for example - and the data is crucial NOTHING else ON THE DISC. Whenever launch you this player you can destroy data. If this is the case, send the drive to a professional data recovery company.

  I'll give you the information on how to test the hard drive to see if it's good physically and how to recover data when you can't in Windows but in doing these things requires a certain level of computer skills. You know yourself the best and that it would be better to take the laptop to a competent local professional. If you do this, do not use a type of BigComputerStore/GeekSquad of the place. Get recommendations from family, friends and colleagues.

  A. test equipment
  
  Test the hard drive with a diagnostic utility downloaded from site of the disc mftr. or use SeaTools for BACK of Seagate. You create a bootable CD with the files you download. You will need a third party burning software to do as the free ImgBurn, Nero or Roxio. Burn as an image, not in the form of data.

  http://www.ImgBurn.com

  http://www.Seagate.com/www/en-us/support/downloads/SeaTools/seatooldreg
  http://Seagate.custkb.com/Seagate/CRM/selfservice/search.jsp?docid=201271 (how-to)

  Boot with the CD that you have done and do a full test of the reader. You will probably need to change the boot order. Your Dell can give you a temporary boot menu if you press F12 as the computer starts. If so, use your arrow key to select the CD drive. Otherwise, press F2 to enter in Setup (BIOS) and change the order of boot on the CD drive first. If the disk fails all physical tests, it must be replaced. Although readers of the laptop cost around $60, you should really consider if it is to put money in such an old machine. You can replace the disk, but the laptop is definitely at the end of its normal life and something else is doomed to failure.

  There is information about the RAM test and other materials here:

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot

  B. retrieve data detach a healthy disk when you are unable to Windows
  
  1 remove the drive and put it in a box of USB drive or use a USB adapter. Attach it to a computer that is running a working XP/Vista/Windows7 installation. Use the work of Windows Explorer to copy the data to the hard drive of the system to the rescue and burn data on cd or dvd.

  2. you can start the target computer with a Bart PE (if you use XP) or a Linux live CD like Knoppix and retrieve the data in this way. General information about the use of Knoppix for this are:

  You will need a computer with two cd records, which is an engraver of CD/DVD OR a USB stick with a capacity to hold your data OR an external USB hard disk formatted FAT32 (not NTFS) *. Download Knoppix .iso image file and create your bootable CD. If you do this in a previous (XP or Vista) operating system, you will need the third burning like Nero, Roxio or the free ImgBurn software (Windows 7 can burn .isos natively). Burn as an image, not in the form of data. Then boot with the CD that you created, and Knoppix will be able to see the files in Windows. If you use the USB key or an external hard disk, right-click on its icon (on the desktop) to get its properties and uncheck "read only". Then click on it to open it. Note that the mouse action by default in the window manager used by Knoppix (KDE) is a simple click to open instead of double-click traditional MS Windows. If you want to burn CD/DVDs, use the K3b program.

  * My understanding is that you can now write on NTFS from Linux partition. If you wish to do this, Google for instructions on the use of the NTFS driver.

  http://www.Knoppix.NET
  http://www.nu2.nu/pebuilder/ - Bart PE Builder

  C. recovery of activity for the future - http://www.elephantboycomputers.com/page2.html#Backing_Up MS - MVP - Elephant Boy computers - Don ' t Panic!

• Cannot start Windows and "Begin repair of launch" or "Start Windows normally" did not work.

  Original title: need help URGENT

  The normal Windows Vista (Home Premium 32 Bit) updated on my DELL INSPIRON laptop... Cannot start Windows

  'Launch Startup Repair' or 'Start Windows normally' did not work.

  What to do next without deleting my data? Thank you.

  Hello

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  Data recovery, if required

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method depends on your hardware in the computer that failed

• Windows Vista does not start. I tried to run the Startup Repair tool and we have tried to select start Windows normally.

  original title: URGENT

  How to start Windows Vista when 'Launch Startup Repair' or 'Start Windows normally' did not work? I want to avoid the deletion of my data.

  Hello

  for starters, the info you received a DVD of windows 7 repair vista usage are BAD

  you need a DVD vists or a vista Startup Repair disk repair vista

  and you can NOT do a repair installation of booting from a DVD in vista

  Repair facilities are on within an operating system

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  If necessary

  Data recovery

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method depends on your hardware in the computer that failed

• error on laptop computer, start windows normally

  Turn on laptop and get to the top with a black screen saying to start windows normally or start windows of the last safe area

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Computer does not start, it goes into the repair system or start windows normally.

  I restarted my computer because my internet is blocked, and when he went straight to the windows repair. I chose 'Launch startup repair', but that just black flashed then went back to the same screen. So I chose to start windows normally, and restarted, it went back to the same thing. It retains, even in safe mode, etc. It's a Lenovo X 200 tablet, I got to the end of 2007.

  If Safe Mode does not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon

  Mick Murphy - Microsoft partner

• Windows does not shut down correctly, please choose an option (safe mode, safe mode with network, start windows normally

  Original title: battery

  When the battery dies on Windows 7 Home premium, what makes the look of the laptop screen as to everyone with the same computer? (IE black, dim and then black, dim and white and then black, Sun & blue, etc.)
  And you always get the "Windows did not shut down correctly, please choose an option (safe mode, safe mode with network, start windows normally)" Note?

  It could be a hardware problem, so it is best to contact DELL or a local technician if the problem persists.

  As a work around, I suggest to update the drivers of the computer display and check if it makes a difference.

  Download the drivers from http://www.dell.com/support/drivers/us/en/19/Product/latitude-e6410

• Window remains white screen after starting windows screen. the system hangs after Mup.sys on safe mode

  The title pretty much everything said.

  The problem occurred on a fault that Dell Vostro 2510 with the additional option should only do the downgrade of Win Xp (from Vista).  As noted, on normal startup, the system will remain in a blank screen after the Windows Xp "loading" screen.  And on safe mode, it will join Mup.sys and then hang there.

  The closest thing that I got from a web search was a thread in forum saying that the official info from Microsoft was that it was a question of Win Xp/motherboard (http://www.hardwareanalysis.com/content/topic/31874/?o=40 halfway to a post by Bobb Fwed).  The poster provided no link, so I don't know how official his info was really.

  Thank you
  -joe

  Contact the Dell Support under conditions of your warranty or Service contract. I suspect that you look at a clean install of Windows here. Good luck! ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Help every time I download Service Pack 3 for XP I have to System Restore my computer because I can't start windows normally. Can someone help me solve this problem?

  After I succesufully download service pack 3 and restart the computer, need me a black screen where I have the options of safe mode, safe mode with network, last known working configuration and start windows normally. Whenever I have select start normally or last known working configuration it takes back me to the same black screen. IM on safe mode with network now. im going to leave it until I can understand it.

  Yes, I have a HP with AMD processor

  I had a feeling. :-)
  See these two pages to your solution:
  The computer restarts after a Stop error message display 0x0000007E (after update with Service Pack 3 for Windows XP)
  Microsoft Windows XP SP3 Upgrade utility for systems with AMD processors.

• My computer won't start in safe mode. When I select "start windows normally", it always starts in safe mode.

  I tried the free space on my hard drive, running antivirus and do the system restore.

  It does not always start in Normal mode.
  1. Close all running programs and open the windows if you are back on the desktop.
  2. Click on the Start () button.
  3. In the search box of the Start Menu () type msconfig and press enter on your keyboard.
  4. The System Configuration utility will open and you will see a screen similar to the one below.

     
     Figure 8. Vista System Configuration utility

     Click the Startup tab.

  5. You will now be on the screen start as shown below options.

     
     Figure 9. Tab of Vista startup in the System Configuration utility

     Make sure the checkbox Start secure is off

  6. Press the apply button, then press the OK button > Restart, etc..
  7. You can also get there by click Start > programs > Accessories > run > type in: msconfig > OK > takes you to the foregoing

  Mick Murphy - Microsoft partner

• Error when starting Windows Vista

  "This application has failed to start because BHO.". DLL was not found. Reinstalling the application may fix this problem.

  and

  "IE3SH Application has stopped working properly. Windows will close the program and notify you if a solution is available. »

  and

  When you open a tab in Windows Explorer I get a "Script error, do you want to keep running the script, yes or no?"

  Hi Buster12345,

  1 when was the last time it was working fine?

  2. did you of recent changes on the computer?

  3. you get script errors in Explorer Windows or internet explore?

  It is possible that some third-party programs installed on the computer causes the error at startup.

  I suggest that you perform a clean boot and check.

  To help resolve the error and other messages, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  See the Microsoft article below as well as try the steps mentioned if you are referring to internet explore.

  How to resolve script errors in Internet Explorer on Windows computers

  http://support.Microsoft.com/kb/308260

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite A210 - 1 4 frequently freezes when starting Windows 7

  Hello

  I have a laptop Toshiba Satellite A210 - 1 4 and updated upgraded to Windows 7 later. I have a problem in which case frequently the OS crashes during startup. This often happens and happens after the text "Starting Windows" appears, but before the windows logo appears. In this case I have to press CTRL + ALT + DELETE to reset the system and bring back to life, Windows 7 starts normally after that.

  I tried to reinstall Windows 7 and it still does not work. I use the 32 bit version if that makes a difference. I installed all the drivers of Toshiba using the [Toshiba Software Installer | http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/downloadDetail.jsp?soid=2475695&pf=true] and the problem still persists.

  Thanks in advance,
  Caleb

  Hello

  Recommends checking the HARD drive first.

  There is a nice tool called Drive Fitness Test which can be downloaded from some 3rd party pages.
  The tool is free and helps you run HARD drive Diagnostics tests.
  If the HARD drive is ok, then the next step should be checking the RAM.

  Tools such as memtest86 + could be used to test the memory.

  But even if there is no error, the RAM could be affected again I recommend that you test the new notebook with Rams

  By the way: check if the BIOS is up to date!