Block of access to the Web interface Ubuntu switches

Similar Questions

• N3048 access to the Web Interface without OOB

  I recently had our switch replaced by RMA and have access to the web interface via oob. I'm not sure how to access ports and other subnets and want to access the web interface of the server room outside. It's probably something very obvious, but I don't have the original switch to check the configuration. Any help would be appreciated. Thank you.

  You can use in-band or oob access to administration from inside or outside the server room.  The port of oob is a completely separate network used for management only, but you can also use a port in the Strip management.  By default, VLAN 1 is usually used in the Strip to transport of management traffic.  If you set an IP address on VLAN 1 you should also be able to manage from this IP address.  Measures would be to define the IP address on VLAN 1, ping ping to test connectivity, remote and then use your browser to connect to the web INTERFACE.  You should be able to use the same username/password that was used for the oob port.  Without a set of name of user and password, the web INTERFACE will not allow the session.

  B

• PC54x8 access to the web interface of WS2012

  Hello. We have a strange problem. Because we are not networking gurus, we use the web interface of the switches to manage them (instead of using the CLI). The problem is that when connect us to the web interface of WS2012, the browser (IE) freezes. We tried this on several machines of WS2012.

  Management of WS2008 R2 works without problem.

  Is this a compatibility issue with IE10 (WS2012) compared to IE9 (WS2008 R2) or something else? I tried to add the address IP for trusted sites, but that did not help. Unfortunately only the servers with WS2012 are connected to this particular switch, so we are unable to manage it more (from the web interface).

  Any ideas what could be the cause of this? The web interface requires Java? Given that we have not installed on WS2012 servers.

  Unfortunately I found no work around to get the software to work with IE10. The recommended solution is to use another browser, which as you've found, works very well. I believe that the idea is that in future updates that IE10 will be supported, but I don't have a roadmap on how that would be released.

• 200 series smart switch (SG200-18) access to the web interface

  Hi all!
  The system flashes green which I understand means that it is currently using the default IP 192.1681.254.

  1. do I need to connect a computer directly into it to get on the Web site? Or do I just use any computer on the local network that uses an IP address from that subnet 192.168.1.x?   The subnet in this branch is etre.1.x in any case.

  2. these instructions in order to use a computer on the same subnet - what is State only when it is in its configuration by default or always? i.e. I'll only ever be able to reach these switches from a computer within the respective branch?  Or, for example, may switch to the branch 1 (sous-reseau.1.x), be configured to allow access to a computer at the head office (sous-reseau.0.x) or via the VPN (sous-reseau.254.x)? How?

  3. how to respond to pings?

  Hi shead, if you connect this switch in a network with DHCP, the device will get a DHCP address for the IP address of management.

  To be able to get web access to a different subnet, you must set the default gateway of the switch of the device, which will happen the router, the sx200 will not forward anything.

  The switch responds to ping by default then there is another problem.

  -Tom
  Please mark replied messages useful

• Help - LI running, but get Apache2 Ubuntu default page while trying to access the Web interface of log insight

  Hello

  I installed the Log Insight 2.5 VM via vCenter Server ESXi 5, 5. I was able to deploy the virtual computer successfully and you can see the network through VAPP Options settings. (Attached picture - TIME settings).

  Question:

  Unable to access LI web Interface. While trying to access the Web interface, I get 'Apache2 Ubuntu by default Page' (img attachment). Insight of the newspaper runs and opens the web application on port 80.

  Newspapers, controlled far-

  status of /etc/init.d/loginsight

  Open a session running Insight

  Attached image Loginsight2-DURATION - file /storage/core/loginsight/var/runtime.log

  # sh li - cassandra.sh - status

  SH: li-cassandra-sh: not found

  Check if the tcp 80 port is open through the netstat command. Yes, it is open.

  Telnet on port 80, it says connection and crashes. Image attached - telnet-LI

  Able to ping the IP address successfully.

  How can I check http logs on console LI?

  I would really appreciate response to this soon. I'm working on installation LI for more than a week and struggling to get through this way.

  Thank you

  Radhika

  I believe that you with the configuration, but I tell you that the configured IP address and the IP you hit in your browser are not still the same IP, Log Insight does not work on Ubuntu, so you hit another system. To prove this, connect you to the console of the Insight newspaper and run:

  # cat/etc/SuSE - release

  SUSE Linux Enterprise Server 11 (x86_64)

  VERSION = 11

  PATCHLEVEL = 2

  You will see that you are running SuSE to see a Ubuntu screen tells me that you have an IP address duplicate in your environment and you hit a node that is not an Insight newspaper. I hope this helps!

• SX10 - how to access the web interface behind a firewall

  Howdy

  I have a very simple configuration, router and behind her SX10. I can't access the web interface of the remote unit. Is there a port that I need to activate or something?

  When the device was connected directly to the modem, with the public IP address, I was able to connect to the web interface.

  any suggestions here?

  I enter anything in the field AllowRemote.

  Thanks in advance!

  Web interface can be accessed using HTTP ether (80) or HTTPS (443).  To you how you want to deploy, but you can use NAT on the router, port forwarding, or even put the SX10 in DMZ on the router.

• Adobe flash player 11.0 blocks access to the Web site home pages

  Why is Adobe flash player 11.0, allowed to block access to the Web site home pages, until their trash is installed?  They should be prosecuted for punishment of the loss of time by Internet users, who spend countless hours trying to fix their garbage, which takes control of the web and blocks PCs access to their program settings, unless it is done according to their specific updates. N ' ILS OWN INTERNET and everything on it, or what?

  Are you sure he blocked it, or the web page requires Flash Player to see this?

  Most web pages require an element of Adobe Flash Player.

  First of all, try to enable Active Scripting in the areas of Sites Internet Options, security settings, trust.

  You should also add a corrupted on.

  Click Start, type: Internet Options

  Press enter

  Select the "Advanced" tab

  Under reset Internet Explorer settings, click "reset".

  This should restore the Internet Explorer default settings.

  Then reinstall Flash Player

  http://get.Adobe.com/flashplayer/

  ----------

  Flash Player

  Troubleshoot installation of Flash Player for Windows

  http://kb2.Adobe.com/CPS/191/tn_19166.html

  Troubleshooting player stability and performance

  http://blogs.Adobe.com/JD/2010/02/troubleshooting_player_stabili.html

  Uninstaller

  http://kb2.Adobe.com/CPS/141/tn_14157.html

  Flash Player Support Forum

  http://forums.Adobe.com/community/webplayers/flash_player

• Unable to access the web interface for SG200-18

  Hello

  I got a new switch and I am trying to connect a UCS.  I ping the switch very well, but when I try to use IE8 or firefox, I can't go to the web interface to configure.

  Here is my configuration:

  Cisco UCS C210 M2

  IP = 192.168.1.100

  Subnet = 255.555.255.0

  Default gateway = 192.168.1.1

  Switch SG200-18

  Default IP = 192.168.1.254 (it is not DHCP)

  Any pointers?

  Tom G

  You need to set a static IP on the PC that is connected to the switch. The IP address of the PC

  must be on the same subnet as the 192.168.1.254.  You may need to try something lower to IE8. Should be

  works with Firefox and IE7. There is also a browser called GreenBrowser which works usually with switches.

  Thank you

  Rick Roe

  Cisco Small Business Support Center

• jumble of text in the web interface after Web Services update / firmware

  I received a message on the screen of my Officejet 6700:

  Update recommended

  An update is available for Web Services (ePrint and Apps).

  Do you want?

  I chose to update now and it installed fine, or so I thought.

  I checked the web interface of the printer, and there is a bunch of text confused, as the code is messed up for the web server.

  I had just finished to check the status of your ink cartridges (and subsequently replaced a), so I have the fully functional Web page fortunately still open on another machine, so I can tell exactly what is forward - after on this page.

  On the tools > gauge of ink page, on the right page (old) the said table (title, first line, first column):

  Cartridges installed

  Color | Magenta | Cyan | Yellow | Black

  Part number

  Type

  End of warranty date (A-M-J)

  First Installation Date (A-M-J)

  Area of ink

  USE

  HP

  But after the software update, it says this:

  Print the self-test Page

  L@S#0456 | Number of recorded events. L@S#0462 | L@S#0552 | L@S#0450

  Use of the accumulated media

  Date

  L@S#0477

  L@S#0561

  L@S#3345

  In addition, the order "supplies" link, with a contextual text of "print order supply."

  now, says "Cartridge", with a contextual text ' block unwanted faxes '

  And "Print Printer Status Report" now says "L@S#2567".

  I went to the support section and found an update firmware, but during download and execution, after you find the printer, he says that he is already up to date and leaves me not choosing to try and reapply the update of the firmware (as is obviously what is happening through the touchscreen menu has already done).

  Should I just restore to factory settings? I think that firmware would not be changed by doing this. It is not an older version of the firmware available on the product support page, to return to an earlier version.

  Via the screen menu touch printer, a Printer Status Report print indicates the firmware version is MPM3CN1322DR.

  How to force a reinstallation of the firmware, or let them difficulty firmware which was released on 25-06 - 2013?

  I've been using Google Chrome and even had 2 tabs open in the same window, one from before the update and the second I opened after the update, so this was not a factor.
  
  I had not revisited the web interface of the printer to date, and currently, I see that the problem has disappeared!
  The version of the firmware has not changed, and I did no manipulation of the printer. I also highly doubt that the main user has nothing, because it is not tech savvy. So, the problem seems to have corrected itself.

  The only thing I see now, that I did not notice before, is that there is a version of firmware fix, but it currently says 0. I don't know what it was before, but I guess zero means that there is a patch, so the firmware didn't automatically update in order to make the problem disappears.

  Problem disappeared, but I don't know how or why. I haven't decided if I will update the second printer that is the same model.

• PowerConnect 2824 cannot enter in the web interface

  My company bought a powerconnect 2824, in any case this is the 1st time, I configure the Dell switch. I managed to Setup using cli mode, but after anyway I can't config interface only able to display information and also cannot enter the web interface with the default setting, or after.

  What I did wrong?

  Have you tried to connect to the web gui via different ports? you mentioned port 1 light does not, which is the port you are trying to access the switch through?

  When you are connected to the CLI, which is the result of show # configuration interfaces?

  What are the customers IP settings to?

• Aironet 1240AG - cannot use the web interface

  I'm trying to set up a new Aironet 1240AG. After that she won an IP from the DHCP in my LAN, I can always connect using the web interface. I use an Internet Explorer 6.0 on Win 2000. It keeps telling me cannot find the server. Please I need help

  Hi Olivier,.

  First off you're welcome :) This method really works without the need for a WLC, be patient. Check the address static IP put you on your TFTP (* range 10.0.0.2 to 10.0.0.30)

  Rename the access point image file in the folder of the server TFTP c1200-k9w7 - tar.default for a series of 1200 access point

  Looks like a problem TFTP (no firewall on your PC?)

  Take a look at the details in the following threads that each has to do with TFTP. There are some great tips to troubleshoot TFTP some of my NetPros favorite ScottMac, Cisco's Stephen and Jack Young. The likely culprit may be you need to uncheck "Hide extensions for known file types" on your server TFTP;

  http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=WLAN%20Radio%20Standards&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc042b/8#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc03c4/2#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddbf271

  I hope this helps! Good luck!

  Rob

  Remember messages useful rate...

• VLAN and the SSID does not not in the Web Interface

  We have a couple of APs which do not show the VLAN and via the web interface of AP SSID.  If you go to the SSID Manager page in the web interface, the page rises but doesn't show any SSID configured.  It goes the same for Services - Vlan.  This page appears but does not show in any VLANS configured.  If you telnet to the APs, you see the mssid listed and all the SSID interfaces.  The SSID on the access point is functional and working.  It is just so hard to use the web interface for these APs.  I tried to compare configs running on APs where the web interface does not show this and APs that it shows, but cannot see any differences.

  Thank you.

  Have you tried with different browsers?

  Nicolas

• Not able to connect to the web interface for a C20

  I have a C20 running 6.0.1 and impossible to access the web interface. I checked all the IP settings using the remote and have achieved nothing out of the ordinary. I am able to ping the C20 and get the cisco logo on the tab of the internet Explorer, but cannot connect. Someone at - it experianced this before?

  Hi Justin,

  Where you can do telnet/ssh to the codec and only the web interface does not come to the top, well want to check HTTP and HTTPS mode and turn it on according to the requirement;

  xConfiguration HTTP NetworkServices Mode: on

  xConfiguration HTTPS NetworkServices Mode: on

  In addition, it is registered on any CUCM?

• Workstation 9 - How to get the Web Interface

  As published in this thread: http://communities.vmware.com/message/2045995 but for VMW8, I can not access or find information in the manual on how to access the web interface of 'New' in VMW9?

  Any tips?

  Thank you!

  The WSX server for 9 Workstation is a separate download and install, see https://my.vmware.com/group/vmware/details?downloadGroup=WKST-900-WIN&productId=293&rPId=2920

  See also the configuration and usage WSX in VMware Workstation.

  -Andreas

• Would it be possible to have the 'Messages' app in the web interface for iCloud?

  I love writing my TEXT with my iMac or my Macbook.

  But when I'm at work, I'm working on a Windows PC.

  So I was wonderning if, one day, Apple could add this app to interface web iCloud.

  This year only, I used an Android phone, I did it with a third-party application (called MightyText).

  A small part has been installed on the phone and wrote messages on the web interface of MughtyText.

  Send your request for feedback:

  Return of goods - Apple