BMG-Mesh

Similar Questions

• Aluminium look and mesh band watch

  It is still possible to use a watch band of mesh in stainless steel with a series of Apple Watch 2 aluminum?

  Hello

  Yes - any band of Apple Watch can be worn with any model of Apple Watch of the corresponding size of the case (38mm / 42mm).

• Mesh Wifi LAN with hardware Apple Airport?

  I read recently about the benefits of wifi mesh networks. I looked at several highly rated router mesh systems; but I don't know if I could not do the same with a system based on Apple Airport extreme and several Apple Airport Express routers.  Does anyone have an idea on the advantages/disadvantages of each approach?

  Trick question that depends on what you mean by "mesh".

  It is not difficult to set up a "roving" network with Apple devices, which is a form of network "mesh".  All airports using the same name of the wireless network, the same level of wireless security and the same password.

  The theory with this type of configuration is that wireless devices can "switch" from one region to the other and still stay connected to the same network as they change to take the best signal from the nearest airport.

  Usually, it works pretty well with the Apple laptops.  But not so well for not at all with most of the PCs, iPhones, iPads and other mobile devices... a fact that most of the articles seem to leave out.

• Satellite M70-169: screen freezes and meshes + mouse freezes

  Hello
  Hope you can help. So far, I'm impressed by my toshiba satellite m70-169.

  He has recently developed an intermittent fault: when the tilt of the screen the effect of light mesh on it and the screen freezes. The mouse also hangs at this point.

  If I tilt the screen one way or the other I can get it to work properly. A slighy inclination of the screen can cause the screen to freeze again. The problem is getting worse, however.

  The machine has never been dropped or struck, but was taken by one of the screen when it is open.

  I disassembled the strainer and push gently on various points and cables but nothing in this area suggests a loose connection or a weak point. So I believe the problem is in the essence. I tried to open this up but it fails because I didn't force anything.

  Question 1: any suggestions on the problem and possible solutions?
  Question 2: advice like how to open the main part, so I can check any loose cables, connectors or broken bones?
  Question 3: patterns for disassembly?

  Even once - I hope you can help - thanks in advance...

  John

  Hi John

  The above user is right. It s too risky to disassemble the laptop without having any experience with laptops.
  It is why I always recommend taking to a technician.

  But if you want, you can have a look here:
  http://www.irisvista.com/tech/laptops/ToshibaM55/laptop_LCD_screen_removal.htm

  It s a site on satellite M55 and withdrawal screen.
  But once again; You can do everything BUT only at your own risk! ;)

• "Mesh" networking Possible with the Airport extreme?

  Now many of you may have heard talk about Eero and Luma, whose routers create a scope "mesh" network by installing 2-3 of their units close to each other.  Whether you're home devices move from one access point to another without a decrease in performance.  In my current setup, I have two extremes from the Airport (connected both) with SSID same, however when I wander around the House, my camera will not let go the first AE until I am in the vicinity of the second AE, how I am down to 1-2 bars of signal, and then at a certain point of annoyance it passes to the 2nd AE with a signal stronger.  Y at - it a setting that I can change which will preserve my investment in my AE current infrastructure, and to somehow get our roaming devices more intuitively go to the AP with the strongest signal faster?

  Thanks in advance.

  Y at - it a setting that I can change which will preserve my investment in my AE current infrastructure, and to somehow get our roaming devices more intuitively go to the AP with the strongest signal faster?

  Unfortunately, Apple provides no practical possibility for the user to adjust parameters either on an AirPort base station or computer or other mobile device WiFi, that would allow a device go faster... or more slowly... as "wandering" on a network with several access points.

  Macs will usually do a good job to switch automatically from one access point to another as they move from one place to another, but most of the PC, tablets, iPhones, and iPads will do that very well... If they do it in all.  With most mobile devices, you will need to temporarily disable the WiFI on the device when it is moved from one place to the other, then re - turn on the WiFi at the new location... and the device will usually pick up the signal from the access point closest and strongest.

• What do you use to clean your stainless steel mesh band? (Not the watch)

  I don't mean to get instructions on cleaning the watch itself, just the mesh stainless steel strip.

  Any suggestions?

  Julia

  Hi Julia

  The instructions from Apple for the cleaning of your loop Milanese are:

  • Wipe the Strip with a recommended cloth (not abrasive and lint). If necessary, you can moisten the cloth with water bit.
  • Dry with a cloth Strip recommended.

  More "clean and dry your band" here:

  Cleaning and port Apple Watch - Apple Support

• Black Mesh for bike 360 compatible watch straps

  Hello

  I have a 360 motorcycle and I want to get a watch band mesh black steel for her I love their way of seeing and I think it would look really nice with the bike 360, the only problem is that I heard the 360 has these "notches" bike, which means that only certain types of watch bracelets are compatible If this is the case can someone post a link to one that is compatible (UK links please). I also fear that laying an another strap will encourage the back to break my first bike 360 rear cracked (under regular use and always with stock black leather band) and the center of actually broken repair my watch and had to replace my watch in any case.

  Thank you

  Arron

  Here's something I thought about investing in.

  http://www.steelconnect.co/M-2-2-5-PVD-black-matte-p/scm225-BM.htm

  Take a look at their site, I think of the money.

• How do I make mesh for small Structures in the MWO?

  Hello

  I use Microwaveoffice AWR to simulate the electromagnetics of nanomecanique. The length of the nanomachanics unit was 1um and the minimum size of the structure was about 15 um. I made of mesh and simulated the circuit using the Solver AXIEM. However, the result was absurd - the width of the stripes of the parameter S12 are about 100 times larger than the experimental value. I discovered that the shape of the mesh was odd; as shown in Figure 1, the mesh did not reflect the shape of the circle and the Combs. So I think that the parameters of the mesh are mistaken. Could you please tell me how to mesh for small structure in MWO? And also I don't know what means the large rectangle in figure 1.

  Hello

  From the picture you attached, I agree that the mesh was too big to take account of combs, although I can't get a complete picture with just the image.  I recommend that you look at the grid X values and Y of the grid on the case.  They should be in the neighborhood of 20 percent of your smaller width of line as a rule.

  I hope this helps.

  Support of the AWR

• Modification of several STL Mesh color dynamically

  Hello

  I'm developing a (attached) VI that loads several STL files into a 3D picture of control. I want to be able to control the color of each mesh STL individually during execution is dynamically. In the present VI I posted, I can change the color of the dynamically created last stitch ("Skull" in my VI). This is achieved by the SceneMesh. SetMeshParameters method inside the while loop. However, I can't find a way to do this for all STS. The solution seems trivial. Any help would be appreciated.

  Thank you

  Jonathan

  Dept of the ERA, IIT Madras

  Nevermind, I was able to figure it myself.  . The solution wa trivial indeed.

  

  Instead of spending the last element of the Nums of the loop ref mesh for, I had the table in its entirety and used as array index to take the mesh at the manipualte as shown above. I have attached the VI update as well. I hope this helps.

  Thank you

  Jonathan

  Dept of the ERA, IIT Madras

• How to use mesh to 3D image optimization

  Hello world

  I'm trying to draw a 2d object in a 3D picture control.

  The 2d object is a type of polar trace data, contour is variable depending on the data set. I want to display in the control of the 3D image, always in 2D. In my view, that the mesh is the solution. But I can't draw anything in the control of the 3D image. Can anyone produce a small example to show how to draw a polygon mesh into a 3D picture control, where I assume that the points on the polygon can be any number.

  I am very new to 3D in Labview picture controls, never needed before. But I managed to produce a nice 3D environment in the control of the 3D image, just stuck on that one aspect.

  Any help is always welcomed and thanks for your time to support this amazing forum!

  James

  Attached, is an example that I put in place.  Nothing is not clear or if you want more explanation, let me know and I'll do my best

  Jeff Peters

  LabVIEW R & D.

• How to display an object mesh continually update with the Labview 3D photo object

  I have a stream of update permanently of 3D images that can be represented in a mesh (a film in 3D if you want). I want to display in the 3D image object so that whenever I acquire a new 3D image that it is displayed. Examples are rare, and I couldn't find anything that dealt with this particular issue.

  Currently (in a FOR/loop WHILE) for each iteration I create an object of the scene, set the geometry as an object mesh newly created, set the texture and it wire eventually to the 3D image. This implementation seems a memory leak (Task Manager shows permanently increases the used memory and processing speed will eventually drop). I guess that's because I recreate the object for each iteration. Problem is, I can't find something that would let me release/delete the object once I'm done with the framework. All the examples I found only deal with the creation of the 3D object once and manipulating.

  What is the appropriate way to code this?

  You just need to use the "narrow" VI on reference photo 3D like this code below. It runs inside the loop.

  

  Now, if you're dealing with the mesh, then you should use the set the mesh to change the points inside the loop and then just close the reference after the code is done. Look at this code below. The trick is to recover the object using Typecast (to more specific reference VI) reference.

  

  Also, look at examples of shipping to:

  C:\nivs_dev\2013\InstallTo\ProgramFiles\National Instruments\LabVIEW\examples\picture\3D Picture Control

  and especially the with Meshes.vi.

• How you connect an Xbox 360 console to an open Mesh Coova wifi hotspot?

  How you connect an Xbox 360 console to an open Mesh Coova wifi hotspot? You need to access a Web page to connect before any other Internet connection can occur? How do you do that on an Xbox 360?

  Hello

  I suggest you to contact the Coova Open Mesh support for more help with this problem.

  Here is the link: https://om.coova.net/forum/2

• Windows Live Mesh for Mac does not work with Mac OS 10.7 Lion

  Maybe someone could help me with this.

  • I migrated to a disk hard again and update of Snow Leopard Lion this week
  • Live Mesh has stopped working so I downloaded the most recent distribution of MS: 15.4.5726.23, 20/07/2011 release date, which says it's for Mac, including the last OS 10.7 Lion as well.
  • It loads, wait, does nothing (the choice of unique to Quit or help menu, and then it ends after about 30 seconds, the LiveAgent not appearing.)
  • I made sure the application has access through the firewall Mac and use the stealth mode.  With stealth enabled, there are messages from the console: Live Agent is listening to 0.0.0.0:59142 proto = 6 AND Live Agent is listening to: ffff:0.0.0.0:59142 proto = 6 AND the first msg repeats.    I also disabled the firewall to test without effect if LiveAgent fails to load. Firewall of variants: with the firewall on, LiveAgent just sits with console messages above until the user clicks on the icon status agent and it then goes to the waiting interminable spinner; with the firewall off, it goes to spinner in less than 15 seconds spontaneously with the GSM, but two sets of their pop up.
  • I repeated a deinstall [app and files] / refresh-download/install process three times and got the same results.
  • In the Finder, and LaunchPad, the icon is displayed normally.
  • I reinstalled the previous version [15.4.5722.2] and the LiveAgent charges, but never decided and just hangs.
  • After doing this and made a fourth installation 15.4.5726.23, 20/07/2011, it now loads the agent but is still suspended as the previous version.
  • If after that, I have now the LiveAgent treat during initialization, but never finished.  It remains active for approximately 8 MB of RAM, but no cycles CPU are used
  • My sync folders are orphans of their source computer, although they always synchronize with my Win7 laptop.
  • I dug a little deeper trying to solve this problem.  I get the following error message if I dig in the 15.4.5726.23 app and run the executable manually:

  aarc01: ~ $ Applications/richard/Windows\ Live\ Mesh.app/Contents/MacOS/Windows\ Live\ mesh; "exit";

  Exception thrown:

  System.IO.FileLoadException: Error 0x1A88.  Debugging resource strings are not available. See http://go.microsoft.com/fwlink/?linkid=106663&Version=3.0.50908.0&File=mscorrc.dll&Key=0x1A88

  [IO. FileName_Name]

  Arguments: Microsoft.LiveFX.ResourceModel, Version = 15.4.0.0, Culture = neutral, PublicKeyToken = 7cec85d7bea7798e

  Debugging resource strings are not available. Often the key and arguments provide enough information to diagnose the problem. See http://go.microsoft.com/fwlink/?linkid=106663&Version=3.0.50908.0&File=mscorlib.dll&Key=IO.FileName_Name

  at Microsoft.MeshOperatingEnvironment.Runtime.Client.MoeRuntime.Start)

  at Microsoft.MeshOperatingEnvironment.Runtime.Client.ILFilter.ExceptionFilter.TryFilterCatchFinally (FilterDelegate filterDelegate, CatchDelegate catchDelegate, TryDelegate tryDelegate, FinallyDelegate finallyDelegate)

  I've seen this behaviour before with v.15.4.5722.2, about 4-5 months ago, but I do not remember what was the solution that solved.

  Can anyone out there advise me?

  THX in advance,

  RC

  Hello RichardCampbellVancouver,

  There is a dedicated forum dealing with problems Windows LIve Mesh. They will be better able to answer your question in the forum.

  Please transfer your question in the Windows Live Mesh Forums on the link below.
  Click on the yellow - ask a Question.

  http://windowslivehelp.com/product.aspx?ProductID=24&version=15.3.2804.0607

  Sincerely,

  Marilyn

• How media player changes the music files (modo-live mesh)

  Hi, seems that media player mark fall files in a folder such as "changed" when I change what should logically be the attributes of the filder (ie the year or kind..). While I understand why media Player that do, it creates a huge unnecessary traffic to live mesh (I'm trying to sync my music folder).

  Furtehrmore, after you have synchronized with another computer, the other computer goes to the internet, detects updates and marks a great numer of files resulting in a huge amount of traffic to the original computer...

  Hello, jmdh

  Please use the Forum for answers!

  Tags for music files are stored in the file. When you change these Nokia is written and therefore actually changed. This happens with other software which publishes these tags as well and not specific to Windows Media Player.

  Let us know if that helps.

  David
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• What F key is for bios on a PC Mesh?

  I tried to show my Hibernate button using the cmd prompt. It has been suggested when I did a search of the forum. I typed in the relevant orders. It worked once maybe twice and then not at all. How do I get my bios and change it, which F is and what key am I am looking to change to show my key hibernate during the shutdown.

  Thank you very much.

  Mesh of PCs using the delete key to access BIOS instead of a Fx buttons.

  Unfortunately, I have absolutely no experience with the inner workings of a BIOS of PC Mesh and could not hope for you coach in this regard. I suggest you see a manual of the card mother before proceeding.