Bootcamp partition Windows will not start since WinUpdate

Similar Questions

• Windows will not start since the update :( Help, please

  Windows could not start. a recent hardware or software change might be the problem

  file\windows\system32\config\system
  status: 0xc00000e9

  When I try to start the system restart that nothing happens

  When I try to restore the computer to factory settings it says that the necessary files are not there.

  My computer was working fine until I installed an automatic update from microsoft. Help, please

  For any problem with the recovery of software/process to factory settings, you will need to contact the manufacturer of your computer.
  This isn't their recovery process, Microsoft.

  Windows Update Forum:

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows will not start since the attempt to install the camera software?

  Hello, I tried to install the camera software, when I did it said my computer to shut off and re satart to complete the installation, when I did a blue screen came up saying that windows had been shut down to protect my computer (not this one). He says to re start computer I did who bought the safe mode/start windows normally screen etc, but nothing's going to restart windows, it starts at, then returns to the blue screen again. Can anyone help please?  Thank you. Trevor

  Hello

  ·         What software have you tried to install on the system and what is the name of the program and where you installed it go?

  ·         What is the exact error message that you meet in the blue screen?

  ·         You're able to boot in safe mode?

  Method 1:

  Step 1:

  I suggest you try and boot into safe mode. Follow the steps mentioned below.

  a. restart and keep tapping F8 until you reach the start menu.

  b. Select safe mode and press ENTER.

  Step 2:

  Do a restore system, safe mode and check. Follow the steps mentioned in the article below.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084/en-us

  Method 2:

  I suggest you to try and initiate the last known good configuration. Follow the steps mentioned below.

  a. restart and keep tapping F8 until you reach the start menu.

  b. Select last known good configuration and press ENTER.

   

  Method 3:

  I suggest to do a restore of the system from the recovery console and check if you are able to boot to the desktop without any problem. Follow the steps mentioned in the article below.

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

• I accidentally put my system as boot partition and my windows partition not marked as boot! Windows will not start! ):

  Hello

  The other day, I have been stupid, play with my windows partitions, I tried to dual-boot android 4.0 with windows, of course, as a study (this version of android has been mainly Linux). A test installation somehow fault, I put my Starter instead of windows system partition! Now windows will not start, it stays on a black screen with a sign less this sort of thing flashes in the corner.
  So I jumped in my disk windows ultimate 7, and it saysBOOTMGR IS MISSING Ctrl + Alt + Del to restart"" and if I try to install Ubuntu via live disc or USB does not start or the other, it displays the same thing.
  Can you please help me solve this problem!
  Nice day!

  After having the BIOS change, restart you your computer with the repair disc in the drive?  If so, what happened?

• Why my TestStand deployment installation appear under my Windows will not start menu of my target machine?

  Why my TestStand deployment installation appear under my Windows will not start menu of my target machine?

  I managed to install the deployments of work to the target machines. However, I expected to see the classified facility "My TestStand system" in my Start menu, but it is not. Am I misunderstanding something here?

  Also, if I do another target second deployment to the station as "My TestStand system B", all LabVIEW files in my previous installation for "My system TestStand" disappear from the directory (c:\Program Files\My TestStand system) target.

  I use TestStand Professional 4.2.1 on Windows XP and LabVIEW 2009 development station.

  Thank you Paul,.

  That solved my second problem and inspired me to look deeper for the response to my first problem. The answer lies in the tab 'distributed file","Installer properties' box 'create a program item:

  

  Wouldn't be nice if it is automatically checked by default for main sequence files? Wouldn't also nice if "Upgrade Code" was regenerated automatically by default whenever we have saved the file *.tsd under another name?

  Thanks again,

  Eugene

• Satellite P20-761: Windows will not start - it loads agp.sys then freezes

  When I pass my laptop it starts with the Toshiba logo as if commissioning, but then the screen goes black with the following message:

  We apologize for the inconvenience, but windows did not start successfully. A recent hardware of software change might have caused this... etc etc.

  Then I have a list of options to choose from:

  Safe mode
  Safe mode with networking
  Safe mode with command prompt
  Last good known Configuration
  Start windows normally

  If I have the choice between the options of safe mode the screen goes through a list of files ending with: multi (0) disk (0) partition (1) \WINDOWS\System32\DRIVE.sys, then freezes.

  If I have the choice between the last two options simply, the screen goes black and nothing happens.

  Of I'm desperate is not to lose all the data that I have accumulated on the laptop. Stupid me not a not bother with backups.

  Discs only can I find supplied with the laptop are 'tools and utilities' and 'product recovery dvd - rom '. Seeing that I am not a technical interest, I'm afraid to try just in case I lose all my most important files.

  Help, please! Answers must be plain English as like I said I'm not really technical. Thank you. I cross my fingers.

  Sounds like something wrong with the graphics card or with the graphics driver.

  I think that you have no other choice than to use the Toshiba Recovery CD and attempt to reinstall the OS. I hope that the graphics card doesn t malfunctions.

  It's very sad, because in this case, you will lose the data on the HARD drive.
  Optionally, you can remove the HARD drive and then to connect to little via the USB port on the other computer, then you can make a backup of your data.

• Pane Windows will not start! Help please!

  I have no idea what exactly happened, but my sidebar will not start. I try to click on it through programs and all he will say is that this windows sidebar has stopped working. a problem caused the blocking of the work programme. Windows will close the program and notify you if a solution is available. I get the same message every time I try to click on run as administrator. I tried so many things, but nothing seems to work. Is it possible that I could reinstall or something? It has been so frustrating. Help!

  Hello

  If you have tried all THE above so it looks like you have a corrupted profile.

  Try these to erase corruption and missing/damaged file system repair or replacement.

  1. run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  2. start - type in the search - box COMMAND find top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  3. then run checkdisk - schedule it to run at the next startup, then apply OK your way out then
  turn it back on.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then do-, use the hidden administrator account for the lowering your user account (the lowest level)
  APPLY/OK, then go back and reset it to the Admin APPLY/OK - this clearly allows corruption. To do this
  a couple of times. Do the same for other accounts that may be difficult. Then, if necessary, you
  can also reset your password in the accounts. Do not forget to leave your account administrator
  and others to the desired level.

  Make another Admin account with your password and use it to fix the others if necessary.
  (just to fix it with, do not use regular account, a safety valve) Always keep a spare part
  ADMIN account.

  DO NOT LEAVE THE ENABLED LSA OR USE DAILY. If it corrupts you are toast!

  How to enable or disable the real built-in Administrator account in Vista
  http://www.Vistax64.com/tutorials/67567-administrator-account.html

  You can run the command Admin account hidden from the prompt here if
  necessary.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  If you can't access your old account that you need then you can always use an Admin to migrate
  towards a new (remember to always leave an Admin account that is not used except for a test
  and fix).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Hope this helps

  Rob - bicycle - Mark Twain said it is good.

• I have an eMachine EL1200 with Windows XP Home Edition. Windows will not start

  I went to start my computer yesterday morning and Windows wouldn't start up.  He continues to go to a black screen saying that Windows has not started up. It gives me options to try:

  1. safe Mode

  2 safe Mode w / network

  3 safe Mode w / command prompt

  4. last know good configuration

  5 start normally

  I tried all the and none start Windows.  Please let me know how I can fix it.

  Hi DavidMitchell,
  I would first remove all external devices from the computer and try to start again. This means that any player mp3, external drives, USB storage devices, etc.

  If this does not work and you're still stuck on these 5 options you listed above, then it might be time to use the Recovery Console.

  Please see the following thread:

  This is an article on what exactly is the Recovery Console and how to use it properly.

  http://support.Microsoft.com/kb/307654

  I hope this helps. Just reply to the results.

• Windows will not start because the following file is missing or corrupt < root windows > < hal.dll windows >

  When I turn on my PC a black screen appears for about 5 minutes, then the following message: Windows could not start because the following file is missing or corrupt I can not any more access to the computer and having to turn it off.

  Hello

  I suggest that you follow the steps described in the links below and check if they help to resolve the issue.

  Link 1:

  "Invalid Boot.ini" or "Windows did not start" error messages when you start your computer

  http://support.Microsoft.com/kb/330184

  Link 2:

  IF the steps in the link 1 does not work, check the steps in the link below.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  http://support.Microsoft.com/kb/314477

• Windows will not start completely freezes...

  Hey!
  I had a problem that my laptop HP 7 windows does not start more... It takes time to get the Palm from windows screen and then it freezes when it gets to the office. Anyone have any idea how to solve this problem? I was thinking about the HP system recovery, but I don't know if that clears all my data or resets just windows. Don't want to lose all my data if its possible somehow. (I have the system on different hard drive recovery not on disks by the way).

  Hello

  Hard disk 1 (303) fast means hard himself is a failure and change Windows is not going to help.  Replacing the hard drive in a laptop is surprisingly easy.  Although the machine in the following link is different from yours, the process is almost identical.

  Replacement hard drive HP

  Once this is done, simply use your recovery DVD to reinstall the operating system on the new drive.

  If you do not have your restore CD, try the link below to see if you can order a replacement.

  http://support.HP.com/us-en/document/c00810334

  A possible way to try to recover your files from a disk non-boot is to follow the process described in the link below.  The CD of the Ubuntu operating system you create can launched from the CD alone (IE it doesn't have to be installed on the hard drive) and I've often found to successfully extract data even a hard failure.  When you created the CD, follow the instructions and see if you can save your existing files.

  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windo...

  Hope this works for you.

  Best wishes

  DP - K

• Photoshop CS6 will not start since the update of Windows (Windows 7)

  This is the second time. Last week, after the update of Windows, Photoshop has started, but no window pops up. I reinstalled Photoshop. Today the same problem. After Windows Update reboot, Photoshop crashes in process Explorer and no window opens.

  Any idea which screws I have to drill?

  Thank you

  Roger

  Second reboot helped. Photoshop is run again.

• HP Pavilion e020us 17: 10 Windows will not start

  I worked on a portable computer that no longer starts.   If I boot from the hard disk in the recovery partition I can't start there on the Windows partition.  I have a choice of Windows 10 of Volume 4, Windows 10 of Volume 4 (Yes it is listed twice) and the Windows recovery environment.  Picking either 10 Windows starts the computer in a reboot loop that can only be stopped by pressing ESC and returning to the recovery environment.

  Boot from CD and try to repair the operating system does nothing - he says that he cannot repair the computer and goes to the recovery environment.

  Auto repair, recovery Image system and System Restore does not work.

  Command prompt shows everything on the C drive is still in place.  CHKDSK shows that all is well with the drive.  But I can't boot from the drive.

  I have not tried to reset the computer only because I'm going to do as a last resort.

  Any suggestions on what to do next?

  Hi @tedly2,

  Welcome to the HP forums! It's a great way to engage, ask questions and find resolutions by working with specialists from the community of HP. I understand that the computer gets stuck in a perpetual loop and does not start. I'll be happy to help you with this.

  A remarkable work was done by train to solve the problem. Hats off to you on this point. I am really impressed with your troubleshooting skills and levels of technical expertise, and it's always a privilege to work with a client of enthusiasts like you.

  First, isolate the problem to be hardware or software related by running diagnostics. Please try a hard reset first. Steps to do:

  • Turn off the computer and unplug the charger. Then remove the battery only if it is removable.
  • Press and hold the power button on the unit for 15 seconds to carry out the static electrical charges inside the machine.
  • Replace the battery and the charger plug it back.

  Diagnostics of material:

  • The main menu of hardware for the HP (UEFI) PC Diagnostics is displayed.
  • Hold the power button for at least five seconds to turn off the computer.
  • Turn on the computer and immediately press the F2 key repeatedly, once every second about.

  Link to run the hardware diagnostics: http://support.hp.com/in-en/document/c03467259

  There is a video partner who shows how it's done. "Please make the step" test using material for the HP (UEFI) PC Diagnostics "from this link. Run full Diagnostics.

  Where it is established that the hardware is fully functional, please try to recover a system from this link: http://support.hp.com/in-en/document/c04758961#AbT4 , choose the right option that best describes your situation. If nothing helps, please order a set of recovery here online media: http://hp.com/drivers

  I hope this helps! Please let me know how it goes. If it helps, please mark this message as "'Accept as Solution". " If you need help, let me know and I will gladly make all that I can to help. If you want to say 'Thank you' for my efforts help, click the ' Thumbs Up ' to give me a Kudos. I really hope that the problem is solved without hassle and things work fine.

  Take care and have a fabulous week ahead.

• Envy 17 j120na: 10 Windows will not start because of the driver installation failed

  History:

  I have a computer laptop j120na Envy 17 that came with windows 8.1.

  I did the free upgride for windows 10 the 18th of this month with success, but because I was not able to decrease or increase the brightness of my computer, or put it to sleep, I realized that I still had to download/update drivers. First I updated the driver GeForce since my SWsetup folder but for the other, I searched online for her, then I saw the driver download progress bar but no progress has been made. I closed the dialog close and there you go, laptop does not start, I just saw a spark between the mouse pointer and the circular blue contraption. Sometimes he shows me a BSOD with lock core auto boost with irql higher acquisition.

  Question:

  Is this a problem with the driver installation? And if so, how do I return it?

  P.s: System Restore is not an option, I restore point.

  Hi there @Aj1baba,

  Thank you for joining the Forums HP's Support and welcome! It is a great place to ask questions, find solutions and assistance of HP and the community! I read your post on the Forums of HP Support. I wanted to join you and help! I understand that you are receiving an error message that says "acquisition of lock core auto boost with irql high ' on your HP ENVY 17-j120na Notebook PC.

  The question could be deemed to occur by downloading the update. It is difficult to say at this stage. As to return to it, your best bet would have been the restoration of the system, but you mentioned only that a system restore does not work because you do not have restore points.

  Have you tried to go into Safe Mode?

  You have media or recovery disk?

  Have you tried to do a Reset BIOS?

  Have you tried perform a hard reset?

  You have beep codes or flashing LEDs?

  Please ensure that all Bluetooth device that you use with the laptop is disabled (including mobile phone).

  Please note: delete all USB/Bluetooth devices. Disconnect all devices of non-essential, as these can cause some problems.

  You can update all your drivers by going to the Web site the driver HP or by using the HP Support Assistant. If you enter Safe Mode, I suggest trying to erase the driver that you have downloaded your downloads (or the folder that you saved it in), so I suggest to make updates using updates of Windows or HP Support Assistant for now.

  Please let me know if I answered your question by clicking the "Thumbs up" if the troubleshooting in this post steps solves the problem for you please click on the button "Accept as Solution" . This will allow to the others is that present the same problem a solution also. If you need assistance, I would be more than happy to continue to help you. Please just re-post with the results of the resolution of the problems.

  Have a great day!

• Windows will not start I just get a black screen

  I have a Dell Inspiron 1520.  When turning on the computer the dell logo comes back, but windows never starts the screen just goes black.  I tried the repair of advanced boot option but I don't get the second screen described on the web site of Dell tech support, the screen goes black again.  Any ideas?

  Hello

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel
  -Double click - Driver tab - click on UPDATE driver - device Manager - map - graph
  then right click on the device and UNINSTALL - REBOOT.

  Another method to try to get to the desktop (try in normal Windows Mode without failure)
  is CTRL + ALT + DEL and the processes tab find EXPLORER.exe and END PROCESS on it.
  then on the tab Applications - lower right - new task - the type in EXPLORER.exe. Safe mode is
  accessible by tapping F8 as you start several times.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all hotfix is usually a hit or miss
  base. That there is no information on a black screen as there is just a blue screen
  adds to the difficulty. Often using a restore point or Startup Repair will have no effect.
  You can try a google to see the proposed repairs, whom some have worked however these
  cover a wide field of efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you do not have the
  discs, your system manufacturer will sell them at low prices. Or try in safe mode if you can get
  it.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (to do the system restore
  It only needs to be bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation
  (if all goes well, the data records and need to reinstall programs). Don't forget to make a good backup or
  3.

  You can use another DVD that aren't copy protected but you you need to own
  Product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can do a repair installation that needs to save the data, but you will
  to reinstall the programs. This also requires correct Vista disks especially for OEM versions.
  You will need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (type in a single line or copy / paste a line at a time and then press enter - do not type)
  parenthesis or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)
  
  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Re: Satellite Pro L300 - update after the BIOS, Windows will not start

  Hello

  I updated the BIOS on my laptop to the latest version and now it does not start in Windows. I can get to the BIOS menu. I tried to restore the default values and saved the day, but he's just a blue screen with writing on whichIi do not have the time to read it before it tries to restart and continues to do the same.

  Any ideas anyone?

  see you soon
  Phil

  Hi chaospunx,

  Which HDD mode did you use before the BIOS update? Perhaps this option, you need to change, then Windows will start up again.

  You can choose between the mode of access AHCI and Compatible HARD disk.
  Check this box!