Boots to black screen

Similar Questions

• HP 500-046: 6 beeps at startup, can't access boot options (black screen) but then Windows loads ok

  After making a system image backup I wanted to test the recovery disc. To start from the cd tried to change bios to disable secure boot and enable legacy startup.  Could not get the pc to boot once so reset cmos by shorting the pins on the mboard.  Now to start always get 6 beeps and black screen, but after a minute, windows login screen lights up and it works fine.  Unable to access the bios Setup screen any key used at startup.  6 beeps indicates a video card problem, but no material error in device mgr points.  Want to update to Win 10, but unsure about do to address this problem starting.  Appreciate any help.

  @JohnN59,

  Thanks for the information to know.

  You can try the DVI port on the motherboard

  I/o Ports and internal connectors

  Rear i/o ports

  Figure: IO back panel

  

  1. USB 2.0: 2

  2. Output S/PDIF port optical

  3. VGA

  4. DVI - D

  5. LAN

  6. USB 2.0: 2

  7. USB 3.0: 2

  8. Audio: Port of central/subwoofer (yellow-orange)

  9. Audio: Rear Speaker Out port (black)

  10. Audio: Side Speaker Out port (gray)

  11. Audio: Line (light blue) port

  12. Audio: Output line port (lime)

  13. Audio: Microphone (Pink) Port

  If is not shows the start then try the Bios reset/recovery (windows + B key).

  Please keep me updated.

• Boots Vista black screen with white cursor and nothing else (Black Screen of Death)

  After a download from Microsoft update last week, my system has rebooted. He first had a screen blue error, rebooted, reported a disk error and automatically run CHKDSK. Since then, the system has started a black with white slider screen and nothing else. This happens at startup options (Normal, safe, safe with the last command good known configuration). Not even sticky keys would come to the top. CTRL-Alt-Delete, Ctrl-Alt-Esc and all other keys has nothing did. Even with a right click.

  I searched all over the web for solutions. I found (and tried) several over the past week, but nothing has worked.

  Here's what I tried...

  F8 held key on boot to the top and entered the startup recovery. Ran of recovery. Initially so found of disk errors. Those fixed. Then he said he could not repair the system and reported two pilot errors.

  Tried system restore. He said that I had no restore points (even if I know that I had before).

  With the help of recovery options, I went to the command prompt. Asked to RegEdit and load the Software hive. Checked the connection entry Windows NT; made sure, it has been set to explorer.exe

  The system, checked RpcSs Key hive. Already the NT AUTHORITY\NetworkService value

  Renamed event connects winevt and not create the Logs folder

  Removed the hard drive. Attached to another system (as slaves), and the registered file permissions. They have screwed everything up. The fixed file permissions and drive put back in original system.

  Œuvres self-retaining keys now. Do not, however, as my sticky keys doesn't have a link to configuration.

  Went back into recovery startup via the F8 key at startup. Now, when I run start recovery, it says that everything is going well and there is no problem.

  I have download the hotfix from article 977675 Microsoft, but I don't know how I can apply it without being able to get into windows. I would like to contact MS e-mail or chat support, but I can't get the product ID without being able to connect (frustrating talk).

  I would like to reinstall OS, but HP does not provide an installation disc with their systems (only a full restore partition). My system is backed up (with the exception of the Windows folder), but I really don't want to have to make a full recovery, as I have a lot of specialized programs and settings that would probably take me a week to re - install and re - set.

  Anyone have any new ideas?

  Hello

  Here's my usual BlackScreen convenience store, because it may be that you haven't tried
  or if you have access you might be able to come back and start some of them.

  ----------------------------------------------------------------------------------------------------------

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
  Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
  on devices and UNINSTALL - REBOOT.

  Another method to try to get to the desktop (try in normal Windows Mode without failure)
  CTRL + ALT + DELETE and on the tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - then
  on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is reached
  by tapping F8 as you start several times.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
  That there is no information on a black screen as it is on a blue screen just adds to the
  Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
  Google to see the proposed repairs, whom some have worked however these cover a wide
  field efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you do not have your system disks
  manufacturer will sell them at low prices. Or try in safe mode if you can get there.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (to do the system restore there only to)
  being bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation (if all goes well
  saves the data, and you need to reinstall the programs). Be sure to do a good backup or three.

  You can use another DVD that are not protected but you will need to copy you have the product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (type in a single line or copy / paste a line at a time and then press enter - type no parenthesis)
  or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)
  
  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Windows does not turn on or restart properly - boots to black screen

  Whenever I reboot my computer or turn the power off and then turn it on, it will send me to a white, black screen. It passes through the small loading bar microsoft, then it sends me to this black screen. If it starts fine then the slider appears, but most of the time there's just on this black screen for hours and hours and I have to hold the power button so he can close.

  I tried to do the analysis of hard drive and restoring the system, but I don't know what the problem is. Any help? Thank you.

  Hello

  ·          Were there any changes made to your computer before this problem?

  Step 1: Use the option ' enable video low resolution (640 × 480) ' start and then update your video card driver.

  a. click the Start button, click the arrow next to Shut Down and then click on restart.

  b. do one of the following:

  ·         If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  ·         If your computer has more than one operating system, use the arrow keys to select the operating system you want to start in safe mode, and then press F8.

  c. on the Advanced Boot Options screen, use the arrow keys to select activate video low resolution (640 × 480) and press ENTER.

  d. connect to your computer with an account of a user who has administrator rights.

  e. If you can see your desktop, there is a problem with your video card. Try to update your video card driver. For more information, see update a hardware driver that is not working properly.

  f. If these instructions allow to solve the problem, you are finished. If this is not the case, go to the next set of steps.

  Step 2: Start the computer in safe mode and disable your video card

  a. start in safe mode: http://windows.microsoft.com/en-US/windows-vista/Start-your-computer-in-safe-mode

  b. sign in your computer with a user account with administrator rights. When your computer is in safe mode, you will see marked Safe Mode in the corners of your screen.

  c. open the Manager of devices by clicking the Start button, click Control Panel, click System and security, and then, under system, clicking Device Manager.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  d. in the list of categories of equipment, expand the category of display cards. Take note of your graphics card.

  e. right click on your graphics card and then click on disable. Confirmation prompt, click Yes.

  f. close all open windows and restart your computer normally.

• Computer will not start!-boots to black screen

  OK so this is what is happening I think maybe breaking it... so I she closed and he was going to shut down, but before I did I wanted to install updates, I have so been lettng but my cat hit the power cord and it turned off I tried to restart it and that I start more... as it does all the normal show the loading bit like him bar all go and bam just a black screen... Ive put in the recovery disks, but they charge that just stop on the waiting screen please and were someone at - it something that can help me or know why it broke? original title: Vcomputer does not start!

  Have you changed the boot order to use disk recovery/s?

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the recovery discs are still not working, you will need to contact the manufacturer of the computer.

  This isn't their recovery process, Microsoft.

  See you soon.

  Mick Murphy - Microsoft partner

• (Redirected) USB Flash Drive Boot (BiOS) - black screen/freeze/without end of loading - need help!

  Hello community Dell:

  I have been using your Inspiron desktop for work. Work requires me to a startup USB flash drive every morning to access work files and programs. I just press F12 and select the USB flash drive that brings me then in a workplace Ubuntu after entering my credentials - very easy.

  I recently bought the X 51 office because I wanted the game after work and it was intended to replace the Inspiron.

  X 51 issues (boot BiOS - secure boot off as with the Inspiron):

  UEFI = I get a black screen after the "loading...". ', it freezes the whole system

  Legacy = told me to restart the system and drive and the message repeats little matter what you press

  I tried USB different slots, ending different to access USB - nothing works!

  I tested another theory that would disable the GPU of the X 51, but this proved futile because the problems themselves was replicated. The GPU is the only unique component between two desktop computers. CPU is i3, i5 vs, vs 4g 8g, 1 TB vs. 2 TB, so I do not see these improvements of specification being the culprit. The X 51 has a different unique Alienware BiOS interface.

  The X 51 will be returned to Dell unless someone can some up with a solution - I would be eternally grateful, thank you.

  Better in this position in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• Won't boot NB205 - black screen and white flashing underscore

  My toshiba nb205 won't start...
  Its shows a black screen with flashing white underscore in the top left...

  What should I do?
  The operating system is bad? Bad hard drive?
  Bad motherboard?

  Please help thanks guys.

  Hello

  I can't give you a precise answer.
  Restart your laptop and enter the BIOS settings.
  Disk recognized and listed correctly?

• Satellite Pro P300 - 13 m - boot problem: black screen with 3 beeps

  Hello

  Satellite Pro P300 - 13 m, I bought a few weeks ago and in time, I had about 5 - 6 times the same rear screen when I tried to start the system. When he does this notebook gives 3 loud beeps (not sure what that actually means).

  When he does this I have to press the power button for 5 seconds and after several times doing this that it will show the Welcome screen toshiba... then sometimes it will automatically restart again and I get this annoying black screen again. Most of the time when I wait about 10 minutes and try to do as well the system starts as usual... Yes... very strange thing here.

  To be honest, I don't want to send the laptop for Toshiba once again, as I could use for my business...

  Then. What could this be? I've already updated the latest version of the BIOS.

  Thnx in advance

  Carl

  Hello Carl

  I have the Satellite Pro P300 (PSPC1E). I installed Windows XP Home edition and my Vista. Use the two operating systems with success and everything is OK.

  What operating system do you use?
  Have you noticed that on the first day?
  Your laptop is placed correctly on the desktop without cooling vents?
  When you start Notepad you see every time that Toshiba welcome screen?

• My macbook pro retina boots to black screen. It does not reset the PRAM.

  My MacBook Pro (15 "Early 2013) retina will have a black screen randomly. It won't restart and reset PRAM does not alter. To do this, the startup sound, but that's all. In addition, hang on to an external monitor does not display. Is there something else to try? It's a new OS (El Capitan).

  Some things to consider: the battery can be 10%, 50%, 100% is not bad, the computer starts after being off for a long time (2-3 hours).

  you have GPU failure

• Satellite L360D - no boot up - black screen

  Our laptop won't start.
  Don't even give a start of the screen (Bios/Cmos output). Not even a cursor or anything like that.
  Screen remains completely black.

  At the beginning of year t helped by pressing a key (we choose: insert) during start and/or remove cable supply.

  But this no longer works. Screen remains black.
  External screen shows or anything.

  Any ideas?

  Thank you
  Peter

  Hi Peter

  On this virtual path, it is not easy to say what can be wrong here.
  When you wrote laptop doesn't boot t, what do you mean exactly? What happens when you press the button walk / stop?
  You don't see anything on the screen? See Toshiba welcome screen?

  Disconnect for computer laptop AC adapter / CC, remove the battery and press the power button for about 20 seconds. After doing this will leave the computer for a while, just connect the power and press the power button / stop. What happens when you do this?

• Satellite L50-A-170 - no boot and black screen on startup

  Hello

  I hope you can help me.

  I have a Satellite L50-A-170 for about a month.
  Today, after 3 days of inactivity, I tried to turn it back on but you can hear noise from the optical drive and the noise of the fan, but the screen remains black.

  It seems to me that you do not even the backlight of the display. I tried to disconnect the battery for a few minutes, but it is integrated.

  You have an idea on how I can proceed?
  I need the PC and data!

  Thank you in advance!

  > It seems to me that you do not even the backlight of the display. I tried to disconnect the battery for a few minutes, but it is integrated.

  For this reason, there is a * reset switch * place the bottom of the unit.
  The detailed image can be found here:
  [The stop switch of strength (hole) for models with one main battery fixed | http://aps2.toshiba-tro.de/kb0/TSB3C03JR0000R01.htm]

• Satellite 1900-303 Wont Boot up black screen only - help!

  I have a major problem. My Toshiba Satellite 1900, Windows XP Home edition, P4, 2.0 Ghz, 256 MB of RAM (not SP2 updated) won't boot to the top.
  I ran Norton Sys works - speed record to defragment the HD. The screen is blank because the level of power that I it turns off after 10 minutes of no entry.

  My son spent portable (lid) open as he called and thought I forgot to close it as the screen is empty, and of course the laptop is off. When I have opened the screen (cover) still once he did not display and the system has no POST beeps. I tried to not start from a Toshiba Recovery CD - nothing, then a recovery disk - no joy - I then tried to boot from a Windows XP boot CD - once again no joy. A friend gave me a loan of its disk of v6.0 of SPINRITE to start from, as he says that he has its own operating system - once again no joy. Battery adapters and power are all ok, we tested with a multimeter.

  Another note is that I have GOBACK installed v3, but because of the fact that the laptop does not start, I can't retrieve the last good point. I also think that as I was running a defragmentation program when this accident occurred the restore points is erased from the memory.

  At this point, I'm stumped. I got a job on the laptop (Excel files) that I need to access. Any suggestions/help would be appreciated.

  My last resort after this forum is to go to the clinic of PC World which I never had used in the past. The laptop was purchased in PC World and I never had a problem with it

  Hi Karen,.

  When you turn on your laptop you see the Toshiba splash screen? In addition, what indicators are light up when you turn on? for example, Ac, battery, hard disk, CD-Rom, etc. ?

• Computer laptop Compaq CQ58 - won't boot Up - black screen

  Hello

  My laptop does not start right once I reset the CMOS battery. Since then he has become black, power is ON & shift caps lock on the keyboard flashes but no sign of a video signal.

  Any suggestions to what is happening & what are the steps I must take to restore visual. All returns are much appreciated!

  Thanks in advance.

  SR

  Thanks for the information,

  Here is a link that explains the sequence as the caps lock light gives you. It seems to be a problem with the memory of the computer.

  The link explains what should be your next step. If you have any questions about the steps, let me know.

• WINDOWS 7 blue screens and boots then black screen several times through the day! View all different types of error messages. BORING

  Well, I have to tell you my story that I was happy that I bought a "new" (DELL) C.P. and 64 bit vista pre-installed and that he had not. and had some problems with my new! Dell xps 9000 from the GET go > but I learned that I was eligible for a free windows 7 upgrade and was also, said that this new victory. 7 program would solve all my problems? B.S., he transformed all senareio into a nightmare, I uninstalled it AND REINSTALLED IT 3 times not to mention having get for 7 different print drivers then reloading all antivirus, blah - blah - blah - I was on the phone with Dell for over 3 weeks now! Of course cannot use a new P.C. like this Hey? I have a file a mile long if it is "they keep a good journal at all? So I will contact the Dell for arrangements to resume their JUNK. Their so-called technical support is aweful @ best. They have me so DARN confused I can't sleep at night knowing what I had paid for my new system and still having all these questions really now this is just crazy... I have also contacted "MICROSOFT" with these problems, as I have a warranty on the win 7 program operating system and when I called the first thing of this guy's mouth was, I had to pay their money $$$ for any type of support? NOW it's sad/mad/nutz out hey? All I know is that I'm the guy with the great Bill to refund my purchase and remains sure if I can't use the c.p. I'm not paying for it! and I don't want it, that is of no use to me! Bye Bye blue screen of Messages of error and dreams MERRY CHRISTMAS to YOU ALL... OH YES HOWS THAT SAYING GO?  "BETTER DAYS AHEAD" that they will be when I'm done with DELL and MICROSOFT! It was an unreal experience more as I said a nightmare! P.S.OH YES NO MORE MIDNIGHT TECH SUPPORT CALL EITHER! CAN YOU IMAGINE THAT CALL ME AT ALL HOURS OF THE NIGHT TO FIX WHAT? NOTHING! WHAT HAPPENED TO DELL AND MICROSOFT

  Hello

  Sorry, but it seems that Dell does not provide a quality service for you. They have to replace their machine
  with a new one that is fully functional and you shouldn't accept anything less. 3 weeks and they did not
  fixed a new machine is excessive. Climbing with Dell and recover your money or a new.

  Would like power to help more.
  Rob - bicycle - Mark Twain said it is good.

• Power outage during Vista SP2 install; black screen on startup of the PC

  Hello-

  I have a PC desktop Gateway which is no longer start after a power failure has occurred during the installation of Vista SP2. The computer displays the progress at the bottom indicator, then, before that can display the login screen, the screen goes black, with a white cursor. CTRL-Alt-Del and Ctrl-Shift-Esc do nothing.

  I tried without success to the following:

  * Safe Mode/Safe Mode control guest - boots to black screen new
  * Startup Repair - told me there is nothing wrong
  * System Restore - tells me there is no available restore points
  * System restore the OEM DVD - can not find hard drive
  * Re-install this is disabled because I can't start Windows Vista-

  There are * all * options other than wiping the disc/lose all my data? The PC is in a remote area and backup drive is not an easy thing to achieve.

  The PC is no longer under warranty of the bridge, and I understand that Microsoft supports is no longer installs OEM of Vista.

  Can anyone help?

  Thank you

  -Andrew

  I can tell you how to make bootable disks, but you already have a disk.

  He has changed since good means of XP repair install from disk by booting from it.

  I would add that info to disk Bootable repair, just in case your DVD is a factory of one computer.

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  It's Vista only repair installation option these days.
  It must be switched on!
  Not much use, is it!

  Good luck with it.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Download the ISO on the provided link and do a repair of the disc.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Above information shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista Startup Repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner