Broadcom netxreme 57xx gigabit controller does not

I have a d610 and upgraded to w7 pro and my audio does not work and cannot get the driver for the two

The D610 Dell does not support win7, just winxp & win2k

Tags: Windows

Similar Questions

Dell Optiplex 745 with Broadcom NetXtreme 57xx Gigabit Controller with Windows 7 x 64 host cannot fill network

All, I am new to the forum but have been reading up on top of a problem that had led me into a wall.
I'm trying to create a development environment that uses VMWare Workstation 7.0.1 (and I tried with 7.0.0 before, leading me to)
update in the hope of a quick solution) as a development of imaging and the test bench. The system is a Dell Optiplex 745, upgraded to 8 GB of
RAM. Unfortunately, it seems that the biggest problem is the network card.
I tried several different operating systems, and all DHCP requests are found in the AUTOMATIC private IP addressing. This is even after I implemented a custom adapter (VMNet2) that fills explicitly to this network card problem. I disabled VMNet0 and all because this dish was not working. I have read some relevant
messages, but nothing seems to help. This included the http://communities.vmware.com/message/675649 and more
positions listed on the registry settings. I don't know what to do at this point.
So, for those who do not know the Broadcom driver issues, they are apparently many. It is important to disable the unloading, but
I'm not able to find the settings in the post linked above. It's quite similar to the OP for this thread. I'm not
know if it's a difference of conductor between the 32-bit and 64-bit implementations. So, I updated from the version of the driver
12.2.2.1 (b57nd60a.sys) of 10.100.0.0 (I think, can not driver rollback now to check because I need to work on VMS for urgent
projects as soon as POSSIBLE). So, as I said, I was unable to find the parameters of this post
()http://communities.vmware.com/thread/191085) mentioned below:
- Large Send Offload (IPv4)
- Large Send Offload v2 (IPv4)
- Large Send Offload v2 (IPv6)
What I found were these parameters:
- Flow control (Auto, I tried to disable)
- Priority and VLAN (priority & VLAN enabled; I tried priority and VLAN disabled)
- Speed and Duplex (Knew better than to mess around here, has made the problems in the past, retired to Auto)
- VLAN ID (always 0)
- Wake Up Capabilities (Magic Packey; no one tried)
- Unloading ARP (Enable; I tried to disable)
- NS unloading (Enable; I tried to disable)
I tried enabling / disabling all, specially those mentioning the unloading, all day without success. This did not help.
Later, I tried to add DontAddDefaultGateway, EnabledRSS and DisableTaskOffload keys to my CurrentControlSet on the
host. For some reason any DisableTaskOffload shows in the regedit, GUI, not the export of text. Don't know what this means, and I'm too
tired of care at this point.
Host registry settings:
Windows Registry Editor Version 5.00
"ICSDomain"="mshome.net."
"SyncDomainWithMembership" = DWORD: 00000001
"NV Hostname"="HOME".
"DataBasePath" = hex (2): 25, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 52, 00, 6f, 00, 6f,
00,74,00,25,00, 5 C, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 D, 00, 33, 00, 32, 00, 5 C, 00,------.
64,00,72,00,69,00,76,00,65,00,72,00,73,00 5 C 00, 65, 00, 74, 00, 63, 00, 00, 00
"NameServer"=""
"ForwardBroadcasts" = DWORD: 00000000
"Domain"="domain.mei.contoso.com."
'Hostname '=' HOME '.
"SearchList"=""
"UseDomainNameDevolution" = DWORD: 00000001
"DeadGWDetectDefault" = DWORD: 00000001
"DontAddDefaultGatewayDefault" = DWORD: 00000000
"EnableWsd" = DWORD: 00000001
"QualifyingDestinationThreshold" = dword:00000003
"NV Domain"="domain.mei.contoso.com"
"EnableRSS" = DWORD: 00000000
"DhcpNameServer"="141.161.200.201 141.161.100.201".
"DhcpDomain"="contoso.com".
So, I'm not where that leaves me. I am attaching a file vmx for a Windows XP (currently only started in WinPE) invited configured with bridged and IP information for the host and the guest. If anyone can help me, I would be incredibly grateful.
Guest VMX file:
. Encoding = "windows-1252".
config.version = '8 '.
virtualHW.version = "7".
maxvcpus = "4".
scsi0. Present = 'TRUE '.
memsize = '512 '.
ide0:0. Present = 'TRUE '.
ide0:0. FileName = 'Pharos PS.vmdk Test '.
IDE1:0. Present = 'TRUE '.
IDE1:0. FileName = "C:\Users\%username%\Documents\ISOs\peboot.iso".
IDE1:0. DeviceType = "cdrom-image".
floppy0.filetype = 'file '.
floppy0. FileName = "autoinst.flp".
floppy0.clientDevice = "FALSE".
ethernet0. Present = 'TRUE '.
ethernet0.wakeOnPcktRcv = "FALSE".
ethernet0. AddressType = 'generated '.
USB. Present = 'TRUE '.
EHCI. Present = 'TRUE '.
Sound.Present = 'TRUE '.
sound.startConnected = "FALSE".
sound.fileName = "-1".
Sound.AutoDetect = "TRUE".
MKS. Enable3D = 'TRUE '.
pciBridge0.present = 'TRUE '.
pciBridge4.present = 'TRUE '.
pciBridge4.virtualDev = "pcieRootPort"
pciBridge4.functions = '8 '.
pciBridge5.present = 'TRUE '.
pciBridge5.virtualDev = "pcieRootPort"
pciBridge5.functions = '8 '.
pciBridge6.present = 'TRUE '.
pciBridge6.virtualDev = "pcieRootPort"
pciBridge6.functions = '8 '.
pciBridge7.present = 'TRUE '.
pciBridge7.virtualDev = "pcieRootPort"
pciBridge7.functions = '8 '.
vmci0. Present = 'TRUE '.
roamingVM.exitBehavior = 'go '.
displayName = "Test Pharos PS"
guestOS = "winxppro.
NVRAM = "Test Pharos PS.nvram."
virtualHW.productCompatibility = "hosted".
easyInstall.keepFloppy = 'TRUE '.
extendedConfigFile = 'Test Pharos PS.vmxf'
ethernet0.generatedAddress = "00: 0C: 29:64:09:63.
tools.syncTime = "FALSE".
UUID. Location = "56 4 d c0 0 b b2 3 b 33 07-24 4 c 65 64 09 63 a4 b1.
UUID. BIOS = "56 4 d c0 0 b b2 3 b 33 07-24 4 c 65 64 09 63 a4 b1.
cleanShutdown = 'TRUE '.
Replay.Supported = 'TRUE '.
Replay.FileName = «»
ide0:0. Redo = «»
pciBridge0.pciSlotNumber = "17".
pciBridge4.pciSlotNumber = "21".
pciBridge5.pciSlotNumber = "22".
pciBridge6.pciSlotNumber = "23".
pciBridge7.pciSlotNumber = "24".
scsi0.pciSlotNumber = "16".
usb.pciSlotNumber = "32".
ethernet0.pciSlotNumber = "33".
sound.pciSlotNumber = "34".
ehci.pciSlotNumber = "35".
vmci0.pciSlotNumber = '36 '.
vmotion.checkpointFBSize = "134217728.
USB:0. Present = 'TRUE '.
USB:1.present = 'TRUE '.
ethernet0.generatedAddressOffset = '0 '.
vmci0.ID = "1701054819".
tools.remindInstall = 'TRUE '.
USB:1.DeviceType = "hub".
USB:0. DeviceType = "mouse".
ethernet0.VNET = "VMnet2.
ethernet0. ConnectionType = "custom".
debugStub.winOffsets.version = "7".
debugStub.winOffsets.value = "0 x 0, 88 x 84, 0 18 0 x 190 x, 0 x 174, 16, 416, 0x22c, 0 x 228, 0x1f0, 0 x 224, 0x20, 0x18, 0x18, 0x20, 0 x 24, 0x11c, 0 x 8, 0 0, 0, 4 x 0, 14 x 100000, 0xc, 0xc, 0x1b0, 0x18, 0x13c, 0x1f4.
Host adapters:
Windows IP configuration
Name of the host...: TOWMI
Suffix main Dns...: domain.mei.contoso.com
Node... type: hybrid
Active... IP routing: No.
Active... proxy WINS: No.
... DNS suffix search list: domain.mei.contoso.com
Contoso.com
Mei.contoso.com
Ethernet connection to the Local network card:
The connection-specific DNS suffix. : contoso.com
... Description: Broadcom NetXtreme 57xx Gigabit Controller
Physical address.... : 00-19-B9-38-5A-03
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Address IPv6 local link...: fe80::25cc:6bfc:91 has 9: d64d % 11 (Preferred)
IPv4 address...: 10.205.3.136 (Preferred)
... Subnet mask: 255.255.254.0.
Lease obtained...: Monday, 1 March 2010 16:00:06
End of the lease...: Tuesday, March 2, 2010 16:00:05
... Default gateway. : 10.205.2.1.
DHCP server...: 141.161.200.213
DHCPv6 IOOKING...: 234887609
DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03
DNS servers...: 141.161.200.201
141.161.100.201
NetBIOS over TCP/IP...: enabled
Ethernet VMware Network adapter adapt VMnet1:
The connection-specific DNS suffix. :
... Description: VMware Virtual Ethernet adapt for VMnet1
Physical address.... : 00-50-56-C0-00-01
DHCP active...: No.
Autoconfiguration enabled...: Yes
Address IPv6 local link...: fe80::ace9:b312:d32d:fb39% 16 (Preferred)
IPv4 address...: 192.168.58.1 (Preferred)
... Subnet mask: 255.255.255.0.
... Default gateway. :
DHCPv6 IOOKING...: 352342102
DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03
DNS servers: fec0:0:0:ffff:1 1%
FEC0:0:0:FFFF:2 1%
FEC0:0:0:FFFF:3 1%
NetBIOS over TCP/IP...: enabled
Ethernet VMware Network adapter adapt VMnet8:
The connection-specific DNS suffix. :
... Description: VMware Virtual Ethernet adapt for VMnet8
Physical address.... : 00-50-56-C0-00-08
DHCP active...: No.
Autoconfiguration enabled...: Yes
Address IPv6 local link...: fe80::1c44:4e88:3178:4ccf % 17 (Preferred)
IPv4 address: 192.168.168.1 (Preferred)
... Subnet mask: 255.255.255.0.
... Default gateway. :
DHCPv6 IOOKING...: 369119318
DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03
DNS servers: fec0:0:0:ffff:1 1%
FEC0:0:0:FFFF:2 1%
FEC0:0:0:FFFF:3 1%
NetBIOS over TCP/IP...: enabled
Tunnel adapter isatap. {4EF89CD9-7A7D-4B80-83C5-A56D5FA6D748}:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Microsoft ISATAP adapter
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes
Card tunnel Local Area Connection * 9:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Teredo Tunneling Pseudo-Interface
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes
Tunnel adapter isatap. {E03C7ECA-35DF-43C6-BCC8-08D2BB8E4233}:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Adapter Microsoft ISATAP #2
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes
Tunnel adapter ISATAP.contoso.com:
State of the media...: Media disconnected
The connection-specific DNS suffix. : contoso.com
... Description: Adapter Microsoft ISATAP #3
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes
Adapters of comments:
Windows IP configuration
The host... name: minint-et0ko7r
Primary Dns suffix...:
Node... type: hybrid
Active... IP routing: No.
Active... proxy WINS: No.
Ethernet connection to the Local network card:
The connection-specific DNS suffix. :
... Description: VMware accelerated AMD PCNet Adapter
Physical address.... : 00-0C-29-64-09-63
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Address IPv6 local link...: fe80::8842:488e:b75:ec51 %2 (Preferred)
Autoconfiguration IPv4 address. . : 169.254.236.81 (Preferred)
... Subnet mask: 255.255.0.0.
... Default gateway. :
DHCPv6 IOOKING...: 33557545
DNS servers: fec0:0:0:ffff:1 1%
FEC0:0:0:FFFF:2 1%
FEC0:0:0:FFFF:3 1%
NetBIOS over TCP/IP...: enabled
See also my VNE screen capture and sample log file attached. Thank you very much in advance for any help.
Sorry, had to rub a small part of the newspaper for my own protection.
Post edited by: alharaka

I'm sorry, I completely forgot to reply to this topic yesterday (get distracted by a matter of work). I'll be back today and noticed that you have marked this as answer. The root cause of the problem was therefore one MAC address per port restriction put in place by your network management team?

Broadcom netxtreme 57xx gigabit ethernet is not supported to install esx 3.5

Hello
I use my laptop Dell E5420 workstation 6. When I try to install esx 3.5 in my computer, it's show error message as port of networking is not supported. Then I tried to install esxi 3.5 in the same system. His installation, but I have not found all of the network adapters. Physical system I have broadcom netxtreme 57xx gigabit ethernet. I changed little in vmx file, but not all.
Please help me

I hope that you use WS 6.5?
you will miss at least the line

ethernet0.virtualDev = "e1000".

Take a look at this vmx - worked in nice on Workstation 6.5

config.version = '8 '.
displayName = "esx35i."
ethernet0. Present = 'TRUE '.
ethernet0.virtualdev = "e1000".
Ethernet1. Present = 'TRUE '.
Ethernet1.virtualdev = "e1000".
floppy0. Present = "FALSE".
guestOS = 'other '.
IDE1:0. AutoDetect = 'TRUE '.
IDE1:0. DeviceType = "cdrom-image".
IDE1:0. FileName = 'VMware-VMvisor-InstallerCD - 3.5.0 - 82664.i386.iso.
IDE1:0. Present = 'TRUE '.
memsize = "1024".
Monitor.virtual_exec = "hardware".
monitor_control.restrict_backdoor = 'true '.
numvcpus = '1 '.
scsi0. Present = 'TRUE '.
scsi0.virtualDev = "free".
scsi0:0. FileName = "esx35i - system.vmdk".
scsi0:0. Present = 'TRUE '.
Sound.Present = "FALSE".
virtualHW.version = "6".

Satellite Pro 6050: WLan controller does not seem to be in Device Manager

I'm a novice guy with computers.

Well, I re-formated my laptop and re-installed all the drivers, but my wirless lan controller does not seem to be in my device manager.
I was just wondering, if the driver needed to be installed in a certain order. I also had my add on the Vodaphone mobile card plugged into slot on the side that would make a difference?

in any well any help would be great
Dane :-)

Hello

As far as I know that the WLan card was optional on this unit. In this case, if you bought the device with wireless network card that WLAN should appears in Device Manager. But if you bought the laptop without the WLan card you won't find it in Device Manager.

PS: The recovery CD already includes the WLan driver and you don't need to t in addition no driver to install.

Ethernet controller does not work on the Satellite L645D-S4030

Basically, I got my windows 7 reinstalled on my laptop due to virus... Now I have a problem with the Ethernet controller does not, I checked my device manager and there is a kind of yellow dash through the icon... Someone knows what is the problem and how can I solve this problem?

BTW, I have a SATELLITE L645D-S4030

Hey Buddy,

Hmm generally if you reinstall Toshiba Recovery disk Windows all drivers will be installed too because the disc contains a picture of the factory settings.
Or you used another drive?

Yellow exclamation mark can mean that there is a driver problem and so it would be advisable to reinstall the LAN driver. Follow the link Timox. After the driver is installed, restart your computer and check again in Device Manager. The yellow exclamation point should normally be gone.

Xbox controller does not work

One of my Xbox controller does not work.

When I turn on my Xbox and I opened (for example) Minecraft.

He looks up at the sky without touching me same controller!

Help, please!

Ask here:

http://forums.Xbox.com/

or

http://forums.Xbox.com/xbox_forums/general_discussion/f/3817.aspx

See you soon,.

J

PlayStation 3 Sixaxies Controller does not work

Hello I am looking for a fix for this problem, I have a perferctly good controller and a new computer windows 7 64 bit and I would like to know why the controller does not work please help thanks

Are you sure Sony support the controller on a PC? If you are just using a pilot implemented by a guy then it probably won't work on 64-bit.

My advice, pick up a wired Xbox 360 controller. Windows Update uses drivers and it will install immediately. If you want to go wireless, you can use a wireless controller with the USB Gaming receiver for Windows. Paul Smith - MVP for Windows desktop experience... I crawled off NNTP - for now. Detachment Aldershot, United Kingdom. On the internet at windowsresource.net and dasmirnov.net. Please post back to let us know what works and what does not. :-)

Why xbox 360 controller does not work with all pc games

Why xbox 360 controller does not work with all pc games

Ask in an xbox forum.

XPS 400 video controller does not

I have a XPS 400 desktop computer that runs currently the 10 Insider Preview Windows operating system and its video controller does not work and so he struggles to play YouTube videos and he is totally unable to play games should be able to play. I once had this computer to run an operating system called Linux Mint and the video controller worked fine until I put Windows 10 on it. In Device Manager the video controller appears under other devices with an exclamation point. I tried to have the search system automatically updates of pilot, but he can't find. In the past I thought that the video controller was that of an AMD processor, but I don't remember why. Recently I watched the original specifications and it comes with an NVIDIA GEFORCE 6800, so I'm not sure she has and this computer has done to my knowledge undergo updates before I owned it but I don't know if its video controller has been changed. Nevertheless, I tried to get help thinking it is an AMD but nothing helps and I tried to download the drivers from NVIDIA but it still does not work as there is very little information on the video controller. Does anyone know a way I could get the video controller to work?

10 Windows will have to use vista old drivers for video cards of vacuum tube. XPS 400/Dimension 9150 can run windows etc. 8 or 10.

Old cards Nvidia cannot use the latest drivers.

the 340 series is the last version supporting older cards.

NVIDIA has officially END END of SUPPORT LIFE in April 2016.
http://www.nvidia.com/download/driverResults.aspx/77224/en-us

http://NVIDIA.custhelp.com/app/answers/detail/A_ID/3473/~/EOL-Windows-driver-support-for-legacy-products

But 64-bit versions of windows 8.1, 10 will require Pentium D 915 or higher with the radiator of the performance of copper.

DirectX June 2010 is required to submit the drivers of DX10, which is what vista uses.

http://www.Microsoft.com/en-US/Download/details.aspx?ID=8109

You download and extract in a folder and run DXSETUP. EXE as administrator.

After that you will need to go into Control Panel, in programs and features add functionality to windows and re enable legacy live show.

Then install of Chrome.

http://www.Google.com/chrome/EULA.html?system=true&standalone=1

Before installing this driver. You must also add the feature back for legacy Live Show on Control Panel. If you do all the right things in the right order, it will work. Control Panel, all the elements of the Control Panel, programs and features, windows features, turning on and outside

Then do the check boxes. You MUST BE online when you do this, because he lament not find features and who need to download them from windows update.

Description	Supported OS	Download
ATI TVT2 Wonder Elite - unique analog NTSC TV Tuner internal, v.8.33.7.1, A00 (v64) Latest driver for the MCE Vista 64 bit for ATI TV WONDER ELITEmore details	Windows Vista 64-bit
ATI TVT2 Wonder Elite - unique analog NTSC TV Tuner internal, v.8.33.7.1, A00 (v32)

Latest driver for the MCE Vista 32bits for ATI TV WONDER ELITEmore details Windows Vista 32-bit

ATI 256 MB RADEON X 850 XT Platinum Edition, Hyper memory PCI-Express X 16 (DVI/VGA/TV out) Radeon X 300 SE 128 MB Radeon X 600 SE, RADEON® X 600 256 MB HYPERMEMORY, 256 MB Radeon X 600, Radeon X1900XTX 512 MB, X 1300 Pro 256 MB, X 1300, X 1300 Pro, dual 512 MB Radeon X1950XTX Crossfire, v.8.332 - 070108 a 1-041388 C - Dell, A01
64 bit Vista WHQL 8.332 driver from ATI. More details Windows Vista 64-bit

ATI 256 MB RADEON X 850 XT Platinum Edition, Hyper memory PCI-Express X 16 (DVI/VGA/TV out) Radeon X 300 SE 128 MB Radeon X 600 SE, RADEON® X 600 256 MB HYPERMEMORY, 256 MB Radeon X 600, Radeon X1900XTX 512 MB, X 1300 Pro 256 MB, X 1300, X 1300 Pro, dual 512 MB Radeon X1950XTX Crossfire, v.8.332 - 070108 a 1-041385 C - Dell - Vista32, A01
8,332 32 bit Vista WHQL driver. More details Windows Vista 32-bit

ATI Radeon X1900XTX 512 MB, v.8.31.100-061024a-039652C-Dell-32Bit-Vista, A01
32 bit Vista driver 8.31.100 driver for UHMGA14. More details Windows Vista 32-bit

ATI Radeon X1900XTX 512 MB, v.8.31.100-061024a-039729C-Dell-64Bit-Vista, A01
64 bit Vista driver 8.31.100 driver for Radeon X1900XTX 512 MB graphics card. More details Windows Vista 64-bit

AGEIA PhysX adapter, v.2.6.2 (plant), A04
AGEIA PhysX driver updated to take in charge the XPS 710 platform. Adds support for the latest games that use the card AGEIA PhysX and Novodex engine. More details Windows Vista 32-bit
Windows Vista 64-bit
Windows XP x 64
Windows XP

ATI Wonder Elite TVT2 - unique analog NTSC TV Tuner internal, v.8.273, A06
Latest version of the driver for ATI TV WONDER ELITE. More details Windows Vista 64-bit
Windows XP
Windows Vista 32-bit

Wireless controller does not work, said the controller is not an installed device

My "network controller" does not work it says... And he did my wireless doesn't work don't as well.
It happened when I installed Windows 7 Ultimate on my Acer Aspire 5542 G. It just says: the network controller is not an installed device or something. I'm not smart with this kind of thing. So can somebody seriously help out me?
I tried to go to the main web site... But nothing will do it. 0: Yes... And I even tried updating the driver but he just said that he does on windows update...

Theres 4 here wireless LAN drivers . Select Notepad / sucks / 5442G.

But you will need to know if its Atheros QMI or Foxconn.

If this is the wireless on board. If its got one? in Device Manager, double click on it go to the Details tab / change hardware ID's for one of the entries, copy and paste it here.

Or if you want I could have a glance with teamviewer.

You'll see what I'm doing. If you get it give me the ID and password, it gives you

Or if you have Skype, my Skype name is the same name I use here

ENE PCI Secure Digital / MMC Card Reader Controller does not

ENE PCI Secure Digital / MMC Card Reader Controller does not

I suggest that you go the manufacturer of your computers website and search for drivers chipset update.

Click Start, type: Device Manager

Press enter on your keyboard

Click with the right button on the controller listed in the tree view of the devices

Click on uninstall

Restart your computer and let Windows redetect.

WIN Pro 8, xbox 360, z axis wireless controller does not

WIN Pro 8, Microsoft Xbox 360 wireless controller, z axis does not.

Axis Z work in the calibration screen, but not in the test screen or in the games must be a driver problem, advice?

Have deleted the driver to allow windows to reinstall the drivers.

Installing the windows driver software 7 for the controller, still the z axis only work in the calibration screen.

I thought that I had the same problem, but see the knowledge base article: http://support.microsoft.com/kb/2757006

Apparently, the problem is only with the test itself dialog box. I also jumped to the conclusion that it must be a driver problem and expects the controller does not work properly in games.

However, the controller DOESN'T seem to work properly in games.

(Mine is actually a Logitech F710, but it uses Xinput anyway).

I hope that your Z axis controller also works outside of the test application, and the information above helps dispel the confusion around this issue.

There is no problem with the drivers or controller, everything works (read below for the explanation and solution)

I had the same problem, with the z axis (Left Trigger (LT) and right trigger (RT)) with a 360 wireless controller by using the adapter on Windows 8 Pro 64-bit wireless controller.

He would not show the entrances to trigger (z axis) on the calibration screen. Looked online and came across this thread in hopes of finding new update of drivers, or a solution.

After reading the post I quoted above, I decided to see if the z axis works in the game, and he does. I tried Street Fighter X Tekken, went to training mode and you can view entries button on the screen, and pressing the RT and LT trigger buttons, they are part of the game and my character not the corresponding move associated with the key as well as to show the button based directly on the screen.

I went then the game controller settings in windows 8 and again once the game controller dialog box does not show the LT and RT (z axis) entered.

Solution: the controller works fine, and not showing is not the z axis is only a cosmetic problem with the Controller dialog box. So just ignore the controller, the z axis dialog box still works in games.

Broadcom netlink gigabit card does not connect to 1 Gbit/s, auto negotiate connects to 10 Mbps

Hello

I am very satisfied with my purchase Alienware Aurora ALX and happy to be part of this community. However, I have this problem:

Does not connect to 1 Gbps Ethernet adapter; Here's what I've tried so far:

(1) confirmed that my router is able to support Gigabit Ethernet. I have two other devices connected to the same speed (an old PC and NAS).

(2) when I set the speed and duplex of the adapter auto negotiate, it will connect to 10 Mbps

(3) I noticed that there is no setting for 1000 Mbps in speed and duplex options.

(4) I tried 100 full duplex MB, it will connect, but my Internet connection slows down less than 1 Mbps (I'm on a 15Mbps connection and test the other PC it could reach around 14Mbps).

(5) I then tried 100 MB half duplex, it will also link and my overall network performance is good.

(6) I have confirmed that I have the current driver from Dell. I've had the computer for 3 days (using windows 7 by the way).

(7) I tried all ports on my router and confirmed that the side of the router has also been on auto negotiate and not trying to force a specific speed.

I hope someone has a solution or suggestion for this problem.

Kind regards

Jason

* SOLUTION * thanks in part to the previous article.

Here is the Giga speed solution that worked for my new Dell Studio 1458. I've read a lot about speeds slow xfer using the Broadcom NetLink LAN connection.

There were two things I did not initially, but were in fact true.

(1) you must use a CAT 6 line on ALL your machines capable of gigabit. I though that a good line of Cat5e support giga speeds. This isn't.

Card Dell NetLink is apparently, some initial negotiations with your router (a bit ' as a fax machine), then after seeing all of your connections.

It will drop the xfer rate down to the lowest common component (i.e. the Cat5e cable). And;

(2) map of NetLink won't give you giga speeds in automatic selection (advanced ethernet properties, speed & duplex). The speed and the duplex window will never

view 1000 MB! You can check if your is10/100/1000 connection by double clicking on the icon of your connection to the Local network.

I checked the speed of my connection giga via a test utility and transferring a 200meg file. The results indicate an increase in the speed of 12 MB/s to 26 MB/s.

These figures do not show a factor of ten speeds increase, we'd all have (so much), but they are in line with transfer rates of others.

I hope this helps!

Toshiba Media Controller does not support Flash Player 11?

My Toshiba media controller plug not launch my apps on internet games and downloads.
and I get a message saying that it is because he does not support the latest version of Adobe flash player 11.

I got around him for awhile by backdating the system restore... but Adobe and windows have caught up.
My computer is only 12 months old probably would follow?

What can I please.

Hello

As far as I know, download you the latest Toshiba Media Controller here:
http://APS2.toshiba-tro.de/TMC/?page=downloads

The plug-in must be compatible with Internet Explorer.

Also check this Toshiba forum thread on this error message:
http://forums.Toshiba.com/T5/drivers-and-utilities/plug-in-problem/m-p/240712

Usb PCMCIA controller does not work with Tecra 8200

Hello

I have an old laptop TECRA 8200 (Intel Pentium III, 847 MHz, 512 MB of RAM) OS: WIN XP with the latest patches. Because there is no USB 2.0 I bought a PCMCIA USB Controller (NEC Chip). The controller acknowledged, but XP is asking for a driver. The controller has not been delivered with a driver.

Does anyone has an idea how I could get the operational controller.

Thank you

concerning

Fred

I mean, independent because this isn't really a toshiba associated problem, could you please put the name of the PCMCIA USB device?
I mean the manufacturer or something because if XP asks you a driver there should be one available, or?

Please, give feedback and what you could also do is to google for the PCMCIA device. The best way is often looking for the chip (in your case, NEC).

Concerning

Broadcom netxreme 57xx gigabit controller does not

Similar Questions

Maybe you are looking for