Broadcom netxtreme 57xx gigabit ethernet is not supported to install esx 3.5

Similar Questions

• Dell Optiplex 745 with Broadcom NetXtreme 57xx Gigabit Controller with Windows 7 x 64 host cannot fill network

  All, I am new to the forum but have been reading up on top of a problem that had led me into a wall.

  I'm trying to create a development environment that uses VMWare Workstation 7.0.1 (and I tried with 7.0.0 before, leading me to)

  update in the hope of a quick solution) as a development of imaging and the test bench.  The system is a Dell Optiplex 745, upgraded to 8 GB of

  RAM.  Unfortunately, it seems that the biggest problem is the network card.

  I tried several different operating systems, and all DHCP requests are found in the AUTOMATIC private IP addressing.  This is even after I implemented a custom adapter (VMNet2) that fills explicitly to this network card problem.  I disabled VMNet0 and all because this dish was not working.  I have read some relevant

  messages, but nothing seems to help.  This included the http://communities.vmware.com/message/675649 and more

  positions listed on the registry settings.  I don't know what to do at this point.

  So, for those who do not know the Broadcom driver issues, they are apparently many.  It is important to disable the unloading, but

  I'm not able to find the settings in the post linked above.  It's quite similar to the OP for this thread.  I'm not

  know if it's a difference of conductor between the 32-bit and 64-bit implementations.  So, I updated from the version of the driver

  12.2.2.1 (b57nd60a.sys) of 10.100.0.0 (I think, can not driver rollback now to check because I need to work on VMS for urgent

  projects as soon as POSSIBLE).  So, as I said, I was unable to find the parameters of this post

  ()http://communities.vmware.com/thread/191085) mentioned below:

  • Large Send Offload (IPv4)

  • Large Send Offload v2 (IPv4)

  • Large Send Offload v2 (IPv6)

  What I found were these parameters:

  • Flow control (Auto, I tried to disable)

  • Priority and VLAN (priority & VLAN enabled; I tried priority and VLAN disabled)

  • Speed and Duplex (Knew better than to mess around here, has made the problems in the past, retired to Auto)

  • VLAN ID (always 0)

  • Wake Up Capabilities (Magic Packey; no one tried)

  • Unloading ARP (Enable; I tried to disable)

  • NS unloading (Enable; I tried to disable)

  I tried enabling / disabling all, specially those mentioning the unloading, all day without success.  This did not help.

  Later, I tried to add DontAddDefaultGateway, EnabledRSS and DisableTaskOffload keys to my CurrentControlSet on the

  host.  For some reason any DisableTaskOffload shows in the regedit, GUI, not the export of text.  Don't know what this means, and I'm too

  tired of care at this point.

  Host registry settings:

  Windows Registry Editor Version 5.00

  "ICSDomain"="mshome.net."

  "SyncDomainWithMembership" = DWORD: 00000001

  "NV Hostname"="HOME".

  "DataBasePath" = hex (2): 25, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 52, 00, 6f, 00, 6f,

  00,74,00,25,00, 5 C, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 D, 00, 33, 00, 32, 00, 5 C, 00,------.

  64,00,72,00,69,00,76,00,65,00,72,00,73,00 5 C 00, 65, 00, 74, 00, 63, 00, 00, 00

  "NameServer"=""

  "ForwardBroadcasts" = DWORD: 00000000

  "Domain"="domain.mei.contoso.com."

  'Hostname '=' HOME '.

  "SearchList"=""

  "UseDomainNameDevolution" = DWORD: 00000001

  "DeadGWDetectDefault" = DWORD: 00000001

  "DontAddDefaultGatewayDefault" = DWORD: 00000000

  "EnableWsd" = DWORD: 00000001

  "QualifyingDestinationThreshold" = dword:00000003

  "NV Domain"="domain.mei.contoso.com"

  "EnableRSS" = DWORD: 00000000

  "DhcpNameServer"="141.161.200.201 141.161.100.201".

  "DhcpDomain"="contoso.com".

  So, I'm not where that leaves me.  I am attaching a file vmx for a Windows XP (currently only started in WinPE) invited configured with bridged and IP information for the host and the guest.  If anyone can help me, I would be incredibly grateful.

  Guest VMX file:

  . Encoding = "windows-1252".

  config.version = '8 '.

  virtualHW.version = "7".

  maxvcpus = "4".

  scsi0. Present = 'TRUE '.

  memsize = '512 '.

  ide0:0. Present = 'TRUE '.

  ide0:0. FileName = 'Pharos PS.vmdk Test '.

  IDE1:0. Present = 'TRUE '.

  IDE1:0. FileName = "C:\Users\%username%\Documents\ISOs\peboot.iso".

  IDE1:0. DeviceType = "cdrom-image".

  floppy0.filetype = 'file '.

  floppy0. FileName = "autoinst.flp".

  floppy0.clientDevice = "FALSE".

  ethernet0. Present = 'TRUE '.

  ethernet0.wakeOnPcktRcv = "FALSE".

  ethernet0. AddressType = 'generated '.

  USB. Present = 'TRUE '.

  EHCI. Present = 'TRUE '.

  Sound.Present = 'TRUE '.

  sound.startConnected = "FALSE".

  sound.fileName = "-1".

  Sound.AutoDetect = "TRUE".

  MKS. Enable3D = 'TRUE '.

  pciBridge0.present = 'TRUE '.

  pciBridge4.present = 'TRUE '.

  pciBridge4.virtualDev = "pcieRootPort"

  pciBridge4.functions = '8 '.

  pciBridge5.present = 'TRUE '.

  pciBridge5.virtualDev = "pcieRootPort"

  pciBridge5.functions = '8 '.

  pciBridge6.present = 'TRUE '.

  pciBridge6.virtualDev = "pcieRootPort"

  pciBridge6.functions = '8 '.

  pciBridge7.present = 'TRUE '.

  pciBridge7.virtualDev = "pcieRootPort"

  pciBridge7.functions = '8 '.

  vmci0. Present = 'TRUE '.

  roamingVM.exitBehavior = 'go '.

  displayName = "Test Pharos PS"

  guestOS = "winxppro.

  NVRAM = "Test Pharos PS.nvram."

  virtualHW.productCompatibility = "hosted".

  easyInstall.keepFloppy = 'TRUE '.

  extendedConfigFile = 'Test Pharos PS.vmxf'

  ethernet0.generatedAddress = "00: 0C: 29:64:09:63.

  tools.syncTime = "FALSE".

  UUID. Location = "56 4 d c0 0 b b2 3 b 33 07-24 4 c 65 64 09 63 a4 b1.

  UUID. BIOS = "56 4 d c0 0 b b2 3 b 33 07-24 4 c 65 64 09 63 a4 b1.

  cleanShutdown = 'TRUE '.

  Replay.Supported = 'TRUE '.

  Replay.FileName = «»

  ide0:0. Redo = «»

  pciBridge0.pciSlotNumber = "17".

  pciBridge4.pciSlotNumber = "21".

  pciBridge5.pciSlotNumber = "22".

  pciBridge6.pciSlotNumber = "23".

  pciBridge7.pciSlotNumber = "24".

  scsi0.pciSlotNumber = "16".

  usb.pciSlotNumber = "32".

  ethernet0.pciSlotNumber = "33".

  sound.pciSlotNumber = "34".

  ehci.pciSlotNumber = "35".

  vmci0.pciSlotNumber = '36 '.

  vmotion.checkpointFBSize = "134217728.

  USB:0. Present = 'TRUE '.

  USB:1.present = 'TRUE '.

  ethernet0.generatedAddressOffset = '0 '.

  vmci0.ID = "1701054819".

  tools.remindInstall = 'TRUE '.

  USB:1.DeviceType = "hub".

  USB:0. DeviceType = "mouse".

  ethernet0.VNET = "VMnet2.

  ethernet0. ConnectionType = "custom".

  debugStub.winOffsets.version = "7".

  debugStub.winOffsets.value = "0 x 0, 88 x 84, 0 18 0 x 190 x, 0 x 174, 16, 416, 0x22c, 0 x 228, 0x1f0, 0 x 224, 0x20, 0x18, 0x18, 0x20, 0 x 24, 0x11c, 0 x 8, 0 0, 0, 4 x 0, 14 x 100000, 0xc, 0xc, 0x1b0, 0x18, 0x13c, 0x1f4.

  Host adapters:

  Windows IP configuration

  Name of the host...: TOWMI

  Suffix main Dns...: domain.mei.contoso.com

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  ... DNS suffix search list: domain.mei.contoso.com

  Contoso.com

  Mei.contoso.com

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : contoso.com

  ... Description: Broadcom NetXtreme 57xx Gigabit Controller

  Physical address.... : 00-19-B9-38-5A-03

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::25cc:6bfc:91 has 9: d64d % 11 (Preferred)

  IPv4 address...: 10.205.3.136 (Preferred)

  ... Subnet mask: 255.255.254.0.

  Lease obtained...: Monday, 1 March 2010 16:00:06

  End of the lease...: Tuesday, March 2, 2010 16:00:05

  ... Default gateway. : 10.205.2.1.

  DHCP server...: 141.161.200.213

  DHCPv6 IOOKING...: 234887609

  DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03

  DNS servers...: 141.161.200.201

  141.161.100.201

  NetBIOS over TCP/IP...: enabled

  Ethernet VMware Network adapter adapt VMnet1:

  The connection-specific DNS suffix. :

  ... Description: VMware Virtual Ethernet adapt for VMnet1

  Physical address.... : 00-50-56-C0-00-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::ace9:b312:d32d:fb39% 16 (Preferred)

  IPv4 address...: 192.168.58.1 (Preferred)

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 352342102

  DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Ethernet VMware Network adapter adapt VMnet8:

  The connection-specific DNS suffix. :

  ... Description: VMware Virtual Ethernet adapt for VMnet8

  Physical address.... : 00-50-56-C0-00-08

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::1c44:4e88:3178:4ccf % 17 (Preferred)

  IPv4 address: 192.168.168.1 (Preferred)

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 369119318

  DHCPv6 DUID customer...: 00-01-00-01-13-19-D6-D2-00-19-B9-38-5A-03

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {4EF89CD9-7A7D-4B80-83C5-A56D5FA6D748}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Microsoft ISATAP adapter

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 9:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {E03C7ECA-35DF-43C6-BCC8-08D2BB8E4233}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #2

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter ISATAP.contoso.com:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. : contoso.com

  ... Description: Adapter Microsoft ISATAP #3

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Adapters of comments:

  Windows IP configuration

  The host... name: minint-et0ko7r

  Primary Dns suffix...:

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :

  ... Description: VMware accelerated AMD PCNet Adapter

  Physical address.... : 00-0C-29-64-09-63

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::8842:488e:b75:ec51 %2 (Preferred)

  Autoconfiguration IPv4 address. . : 169.254.236.81 (Preferred)

  ... Subnet mask: 255.255.0.0.

  ... Default gateway. :

  DHCPv6 IOOKING...: 33557545

  DNS servers: fec0:0:0:ffff:1 1%

  FEC0:0:0:FFFF:2 1%

  FEC0:0:0:FFFF:3 1%

  NetBIOS over TCP/IP...: enabled

  See also my VNE screen capture and sample log file attached.  Thank you very much in advance for any help.

  Sorry, had to rub a small part of the newspaper for my own protection.

  Post edited by: alharaka

  I'm sorry, I completely forgot to reply to this topic yesterday (get distracted by a matter of work).    I'll be back today and noticed that you have marked this as answer.  The root cause of the problem was therefore one MAC address per port restriction put in place by your network management team?

• Broadcom netxreme 57xx gigabit controller does not

  I have a d610 and upgraded to w7 pro and my audio does not work and cannot get the driver for the two

  The D610 Dell does not support win7, just winxp & win2k

• Broadcom Corporation NetXtreme BCM5764M Gigabit Ethernet

  Hi all

  Just bought a HP Z800 of high-spec workstation I use in my lab at home and I need VIB/drivers for the on-board "Broadcom Corporation NetXtreme BCM5764M Gigabit Ethernet to."

  The works of bare metal installation install fine, but any nested ESXi hosts without any NIC - someone has used before and have a link to where I can download the VIB?

  I'll probably get in on a second hand Intel NIC to work around this problem, but it would be great if someone has already done this and has any tips.

  Thank you

  Jon

  OK, I solved this... and my boy I feel like a "retarded". It turns out that in my haste to deploy virtual computer, I only gave 2 GB RAM... as soon as I expand this to 8 GB, it works perfectly.

  Here is the virtual machine with 2 GB;

  

  And now with 8 GB;

  

• Thunderbolt to Gigabit Ethernet adapter not working

  Hello

  I'm new to this community has never had a problem on my mac since I had last year.  MacBook Pro retina mi 2014 running El captain.

  My ethernet is not picking up DHCP and thunderbolt ethernet does not appear in the network interface.

  I use also fell in love with VGA Converter works on the two test port.

  I also reset the PRAM and the MSC still nothing.  Also restored some peripheral preference to another forum I found on the internet.

  I created another account from administrator to test to see if the interface resumes, still nothing.  How ever wifi works without problem

  Thanks in advance if anyone could help with my problem.

  Dump of information systems presents its collection as below.

  Bolt of lightning to Gigabit Ethernet Adapter:

  Name of seller: Apple Inc..

  Device name: Thunderbolt to Gigabit Ethernet Adapter

  Vendor ID: 0 x 1

  Device ID: 0 x 8003

  Revision of the device: 0x1

  UID: 0X0001000203A8FCF0

  Apple serial number: DTN450706APDWKHBZ

  Route of chain: 1

  Firmware Version: 5.5

  Port (upstream):

  Status: Connected device

  Link status: 0x2

  Speed: up to 10 Gb/s x 1

  Port Micro Firmware Version: 0.0.8

  I have this problem as well. My crush to the ethernet adapter was working yesterday, but now I have not been able to run all day. I even tried everything said in this thread: ImtiazThunderbolt Ethernet does not work after upgrade to Yosemite , you should try what is in the thread, as it has worked for some people.

• This architecture is not supported on install

  pc power problem?

  http://www.Skype.com/intl/en/get-Skype/on-your-computer/MacOSX/2-8/

  Use the above link to PPC. Architecture PPC version 2.8 support.

• No internet access since the passage on the Bell internet security at McFee. The Code 19 in speedstream and broadcom netxtreme network adapters. What should I do to fix this please

  Hello

  Has been forced to change over to McFee Bell internet security. Since then, have no internet access all other functions still work. Always have interent as can use with laptop. Have now no application security on the computer. When troubleshooting had 19 of Code to the following: all have a yellow circle with a black exclamation point:

  Broadcom NetXtreme 57xx Gigabit Controller

  Broadcom NetXtreme 57xx Gigabit Controller - Miniport Radialpoint (x 86)

  SpeedStream USB Ethernet adapt - Miniport Radialpoint (x 86)

  Miniport Wan (IP) - Radialpoint (x 86) minipoints

  Have Windows XP. Dell 8400 desktop.

  Help, please

  D

  Hi, thanks for the information.

  I tried a back roller and tried uninstalling and reinstalling still nothing worked.

  My office is a Dell 8400 to the Dell website and went to download the 57... Update on a USB drive.

  While load to my desktop and it worked. So I completed then other updates to my Dell desktop computer.

  Thank you

  Dee

• My PXE / ESXi autodeploy is unable to see my cards network Broadcom NetXtreme II 10 Gigabit Ethernet (BCM57810).

  My PXE / ESXi autodeploy is unable to see my cards network Broadcom NetXtreme II 10 Gigabit Ethernet (BCM57810).
  

  
  

  What I'm missing here?

  
  

  # Extract the bundle off the downloaded zip line and place it in C:\AutoDeploy

  Add-EsxSoftwareDepot - DepotUrl C:\AutoDeploy-VIBS\BCM-NetXtremeII-11.0-offline_bundle-1553810.zip - net-bnx2x name | Sort descending creationdate | Select creationdate, Version, StatelessReady, summary

  CreationDate Version StatelessReady summary

  ------------                          -------                                                     -------------- -------

  21/01/2014-07:10:23 1.78.79.v50.2 - true 1OEM.500.0.0.472560 bnx2x: driver for VMware ESX

  08-02-2012 03:00:42 1.61.15.v50.3 - 1vmw.510.0.0.799733 true bnx2x: driver for VMware ESX

  # Add the driver (use force because complains and fails otherwise)

  Add-EsxSoftwarePackage - ImageProfile "Profile001" - SoftwarePackage net-bnx2x-force

  # Check it is there

  Get-EsxImageProfile "Profile001" | Select viblist - ExpandProperty | where {$_.} Name - like "net-bnx2x"} | FT-auto

  Date created Version of the vendor name

  ----      -------                           ------   -------------

  Broadcom 1.78.79.v50.2 - 1OEM.500.0.0.472560 net-bnx2x 21/01/2014 07:10:23

  # Export

  Export-EsxImageProfile - ImageProfile "Profile001" - ExportToBundle - FilePath "C:\Users\Administrator\Desktop\ESX-Software-Depot\Profile001.zip".

  WARNING: The image profile is not validated.  ISO / offline Bundle will always be generated, but may contain errors and may

  functional.  Errors:

  WARNING: Requires the VIB Broadcom_bootbank_net - bnx2x_1.78.79.v50.2 - 1OEM.500.0.0.472560 com.broadcom.cnic_register - 9.2.0.0, but

  be satisfied within the ImageProfile. However, the VIb (s) Broadcom_bootbank_misc-cnic - register_1.78.75.v50.1 - 1OEM.500.

  can meet this requirement.

  > # Confirm ESXi image name

  > Get - EsxImageProfile - name Profile001 | ft - auto

  Vendor name has changed the level of acceptance

  ----       ------ -------------        ----------------

  VMware Profile001 27/02/2014 PartnerSupported 18:44:45

  >

  > # Net-bnx2x Confirm is a software installed

  >  Get-EsxImageProfile "Profile001" | Select viblist - ExpandProperty | where {$_.} Name - like "net-bnx2x"} | FT-auto

  Date created Version of the vendor name

  ----      -------                           ------   -------------

  Broadcom 1.78.79.v50.2 - 1OEM.500.0.0.472560 net-bnx2x 21/01/2014 07:10:23

  >

  > # Confirm the current rule of deployment deploys profile001

  > Get-DeployRule-name *

  Name: DefaultBoot

  PatternList:

  ItemList: {Profile001, cell01}

  If you put all the VIB - names in a single order, separated by commas, then it works fine

  Add-EsxSoftwarePackage - ImageProfile - misc-cnic-register,net-cnic,net-bnx2x,scsi-bnx2i,net-bnx2 SoftwarePackage

• I run xp coffeehouse get an icon remove the device safely. I check it and it is for a card broadcom netlink gigabit ethernet which can not be deleted

  I run xp family on a computer laptop hp compaq 6510 b.  The broadcom netlink gigabit ethernet adapter is part of my motherboard.  Why do it and can I get rid of him?

  Hello

  1 have had any changes made to the computer before the show?

  Restore the system to the date and time when the computer was working fine.

  http://support.Microsoft.com/kb/306084

  If this message has always been to present its likely that the Ethernet card that is built into the computer is connected to the motherboard using a USB connection (this is common in laptops). If this is the case, there is nothing that can be done to remove the message that the deactivation of the Ethernet card, but this will prevent you from being able to use wired Internet/network connections.

• Broadcom netlink gigabit card does not connect to 1 Gbit/s, auto negotiate connects to 10 Mbps

  Hello

  I am very satisfied with my purchase Alienware Aurora ALX and happy to be part of this community.  However, I have this problem:

  Does not connect to 1 Gbps Ethernet adapter; Here's what I've tried so far:

  (1) confirmed that my router is able to support Gigabit Ethernet.  I have two other devices connected to the same speed (an old PC and NAS).

  (2) when I set the speed and duplex of the adapter auto negotiate, it will connect to 10 Mbps

  (3) I noticed that there is no setting for 1000 Mbps in speed and duplex options.

  (4) I tried 100 full duplex MB, it will connect, but my Internet connection slows down less than 1 Mbps (I'm on a 15Mbps connection and test the other PC it could reach around 14Mbps).

  (5) I then tried 100 MB half duplex, it will also link and my overall network performance is good.

  (6) I have confirmed that I have the current driver from Dell. I've had the computer for 3 days (using windows 7 by the way).

  (7) I tried all ports on my router and confirmed that the side of the router has also been on auto negotiate and not trying to force a specific speed.

  I hope someone has a solution or suggestion for this problem.

  Kind regards

  Jason

  * SOLUTION * thanks in part to the previous article.

  Here is the Giga speed solution that worked for my new Dell Studio 1458.  I've read a lot about speeds slow xfer using the Broadcom NetLink LAN connection.

  There were two things I did not initially, but were in fact true.

  (1) you must use a CAT 6 line on ALL your machines capable of gigabit.  I though that a good line of Cat5e support giga speeds.  This isn't.

  Card Dell NetLink is apparently, some initial negotiations with your router (a bit ' as a fax machine), then after seeing all of your connections.

  It will drop the xfer rate down to the lowest common component (i.e. the Cat5e cable).  And;

  (2) map of NetLink won't give you giga speeds in automatic selection (advanced ethernet properties, speed & duplex).  The speed and the duplex window will never

  view 1000 MB!  You can check if your is10/100/1000 connection by double clicking on the icon of your connection to the Local network.

  I checked the speed of my connection giga via a test utility and transferring a 200meg file.  The results indicate an increase in the speed of 12 MB/s to 26 MB/s.

  These figures do not show a factor of ten speeds increase, we'd all have (so much), but they are in line with transfer rates of others.

  I hope this helps!

• HP ENVY 15 t-k000 CTO Notebook: HP Envy My network adapter does not support gigabit speeds. Is there an upgrade available?

  My HP Envy 15 t-k000 works very well, but it is slow. I thought it was my internet until I did some troubleshooting and discovered that I don't get the super fast speed that I'm supposed to receive this is because my computer does not have a fast enough network adapter. He's currently the Qualcomm Atheros AR9485 it came with. I watched the maintenance manual and could not find an upgrade. Is there a module I can replace with allowing for speeds 1 G?

  The part number for the laptop is G0T55AV.

  Thank you!

  Hello:

  The adapter you mentioned... Qualcomm Atheros AR9485 is the wireless network card, and I do not think that this card connects everything faster than 72 Mbps.

  Your laptop comes with the card Realtek 10/100 ethernet (wired) and it cannot be upgraded because the ethernet chip is part of the motheboard.

  If you want a gigabit ethernet connection, so I advise you to buy an external USB to RJ-45 gigabit ethernet adapter.

  You won't find any wireless card that will go beyond the rate of 867 Mbps AC, and you would need a router ca to achieve these speeds.

  You would also dismantle the entire notebook to replace the wireless card and if your laptop has a single antenna attached to the atheros wireless network card, you will not be able to upgrade to the fastest wireless card.

  A proper AC map would be the Intel 7260 wireless card if your mobile phone has two antennas attached to the atheros card.

  http://www.Intel.com/content/www/us/en/wireless-products/dual-band-wireless-AC-7260-Bluetooth.html

• Connection not lost of Atheros L1 Gigabit Ethernet 10/100/1000Base-T Controller no windows 7 64 bit does not fixed the driver version v2.4.7.29_WHQL

  Connection not lost of Atheros L1 Gigabit Ethernet 10/100/1000Base-T Controller no windows 7 64 bit does not fixed the driver version v2.4.7.29_WHQL.

  It's sad to see how Samhrutha answer to the question in this way.

  The driver does simply not good.
  The only option to address this situation in the meantime a driver that works, disable features in ' Configure, Advanced tab "on the actual card.
  Different properties exist here. Try to enable / disable some of them. It helped for me on Win7 x 64 ASUS MB.
  Kind regards
  fundutzi

• % CABLE_MODEM_HWIC-3-CONTROL_PLANE_FAIL: RBCP failure: failed to add the service ACE flow - type Ethernet not supported

  Hi all...

  I think % CABLE_MODEM_HWIC-3-CONTROL_PLANE_FAIL: RBCP failure: failed to add the service ACE flow - type Ethernet not supported

  on my 1841 which is currently set to L2L via internet cable. Anyone seen this before? I can't find anything on Cisco related to this.
  The tunnel rises and I got the same configs using DSL except interfaces are different. Thank you...
  My configs are below:
  crypto ISAKMP policy 10

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  # address a.a.a.a isakmp encryption key

  ISAKMP crypto keepalive 20 periodicals

  !

  life crypto ipsec security association seconds 28800

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac xform

  Crypto ipsec df - bit clear

  !

  10 VPN ipsec-isakmp crypto map

  the value of a.a.a.a peer

  Set transform-set xform

  PFS group2 Set

  match address CRYPTO_ACL

  !

  interface cable-Modem0/1/0

  no ip address

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  !

  interface BVI1

  IP address 98.x.x.x 255.255.255.224

  IP virtual-reassembly

  VPN crypto card

  Hello DialerString,

  I fear that the ACL is not related to the question, so I expect not to see anything in the debug output

  Hope to help

  Giuseppe

• How do I install the Broadcom NetXtreme II Ethernet on ESX 4.1.0 800380 network controller drivers

  Hi all

  Can someone let me know how to install the drivers for Broadcom NetXtreme II Ethernet on ESX 4.1.0 800380 network controllers?

  Specific commands pls let me know, installation of the ILO, blade HP Proliant BL460c G7.

  Kind regards

  Ajay

  Drivers for your server is found directly at hp:

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?sp4ts.oid=4194638&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswEnvOID%253D4091%257CswLang%253D%257Caction%253DlistDriver&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• HP ML350P g8 have only 100 MB connection on Broadcom BCM5719 Gigabit Ethernet Esxi 5.5

  Hello

  I have HP ML350P g8 that has recently settled with Esxi 5.5, but I have 100 MB of connection on BCM5719 Gigabit Ethernet of Broadcom that are connected with Gigabit HP switch.

  Tried to restart the server, but no luck. any idea. It seems that the driver has been installed with custom HP Esxi ISO. See the photos

  Any idea? Thank you.

  Just decide that, have you already checked the switch physical configuration of the port and the cable network?

  André