Button problem, connect to the URL

Similar Questions

• Server connection error:-1 there is a problem connecting to the server... hp photosmart 5510

  HP photosmart 5510 e - while a printer B111a

  Windows vista 32-bit

  connection error message-Server error:-1 there was a problem connecting to the server, press Retry or ok to continue

  No changes have been made to my operating system

  Try to add new applications with eprint center of my Compaq Presario CQ60 laptop to my HP printer. Computer tells me that the new applications are there and ready to use, but printer says 'server connection error "? I followed all the instructions to connect to the wireless router, but I'm not sure how to connect to the "Server"?

  The steps below a usually resolve the problem you are experiencing:

  1. unplug the power cord at the back of the printer.

  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).

  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.

  4. wait for 30 seconds, then plug the printer back and power.

  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.

  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):

  1. tap the wireless at the top of the screen of the printer and note the IP address.
   
  2. Enter the IP address in the address bar of a web browser on a computer and press on enter or click the go button browser.
   
  3. the printer status page must be open.  Click network in the upper part.
   
  4. click on networking on the left.
   
  5. Select the Proxy settings.
  Note: If you are prompted for a redirect, click OK.  If you receive a certificate warning, select the option that allows you to continue anyway.
  If you receive an internal system error, refresh the page until it loads the proxy settings.
   
  6. check that all fields are empty.  If they are not, make them disappear and make sure that the Proxy Server requires authentication is unchecked and click on apply.  You should get a success message.
   
  7. click on the network address (IP) on the left.
  Note: If you only configuring IP address and DNS address with a yellow note Configuration, refresh the page until it loads completely.
   
  8. leave automatic IP IP address Configuration.
   
  9 change the DNS address to the manual DNS Server Configuration.
   
  10. enter manual for the manual preferred DNS Server 8.8.8.8 and 8.8.4.4 for auxiliary DNS.
   
  11. click Apply and you should get a success message.
   
  12. turn off the printer for 30 seconds and then turn it on again to force the new settings take effect.

  Let me know if you have any additional questions. Thank you!

• Unable to connect to the URL of planning after new installation & configuration 11.1.2

  I installed 11.1.2 on Windows 64 bit environment and configured.
  
  This is my environment:
  Box 1. FS, Essbase, Weblogic, Oracle HTTP. Successfully set up and works great no problem (I don't not configured web server in FS yet)
  Box 2. Planning. Installation and configuration was successful.
  
  Question: but unable to connect to the URL http://servername:8300/hyperionplanning/logon.jsp and http://servername:19000/hyperionplanning/logon.jsp (I'm not expecting 19000 will connect)
  
  Trobleshooting:
  When executing netstat, 8300 does not run on this box.
  Also configured to 'Manage the clusters of planning' with no luck.
  The WebLogic (11g) server indicated State planning is unknown.
  Diagnosis indicates: 1. There is no 2 System-jazn-"Data.xml" file. Web application for planning has no reason of error: java.net.ConnectException: Connection refused: connect
  I stopped and restarted service app planning several passages of time without any problem but unable to connect to the URL and no port is running.
  Journal of planning does not reveal the error messages.
  EMP system log shows ServletContainerAdapter manager not initialized successfully
  There is no error in start-HyS9Planning - out .log.
  Start-HyS9Planning - error.log shows the requested service has already been started.
  
  There is an error in the validation log:
  
  [2010-10 - 06T 10: 18:23.171 - 04:00] [EPMVLD] [ERROR] [EPMVLD-02017] [oracle. EPMVLD] [tid: 25] [ecid: 0000Ii1u3V8EcLPMyeU ^ MG1Cf8KW00000E, 0] [SRC_CLASS: com.hyperion.cis.validation.checkers.impl.AppServerChecker] verification code error response: []
  java.lang.Exception: java.net.ConnectException: connection refused: connect
  at com.hyperion.cis.utils.HttpUtils.checkResponseCodeGood(HttpUtils.java:153)
  at com.hyperion.cis.utils.HttpUtils.checkResponseCodeGood(HttpUtils.java:66)
  at com.hyperion.cis.validation.checkers.impl.AppServerChecker.checkWebApplication(AppServerChecker.java:159)
  at com.hyperion.cis.validation.checkers.impl.AppServerChecker.checkWebApplications(AppServerChecker.java:119)
  at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
  at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
  at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
  at java.lang.reflect.Method.invoke(Method.java:597)
  at org.mozilla.javascript.MemberBox.invoke(MemberBox.java:160)
  at org.mozilla.javascript.NativeJavaMethod.call(NativeJavaMethod.java:243)
  at org.mozilla.javascript.optimizer.OptRuntime.callProp0(OptRuntime.java:119)
  to org.mozilla.javascript.gen.c14._c0(./scripts/webappcheck.js:2)
  to org.mozilla.javascript.gen.c14.call(./scripts/webappcheck.js)
  at org.mozilla.javascript.ContextFactory.doTopCall(ContextFactory.java:401)
  at org.mozilla.javascript.ScriptRuntime.doTopCall(ScriptRuntime.java:3003)
  to org.mozilla.javascript.gen.c14.call(./scripts/webappcheck.js)
  to org.mozilla.javascript.gen.c14.exec(./scripts/webappcheck.js)
  at org.mozilla.javascript.Context.evaluateReader(Context.java:1119)
  at com.hyperion.cis.validation.RunningEnviroment.processSource(RunningEnviroment.java:222)
  at com.hyperion.cis.validation.RunningEnviroment.runScript(RunningEnviroment.java:279)
  to com.hyperion.cis.validation.RunningEnviroment.access$ 000 (RunningEnviroment.java:40)
  to com.hyperion.cis.validation.RunningEnviroment$ 1.run(RunningEnviroment.java:132)
  Caused by: java.net.ConnectException: connection refused: connect
  at java.net.PlainSocketImpl.socketConnect (Native Method)
  at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333)
  at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195)
  at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182)
  at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366)
  at java.net.Socket.connect(Socket.java:519)
  at sun.net.NetworkClient.doConnect(NetworkClient.java:158)
  at sun.net.www.http.HttpClient.openServer (HttpClient.java:394)
  at sun.net.www.http.HttpClient.openServer (HttpClient.java:529)
  to sun.net.www.http.HttpClient. < init > (HttpClient.java:233)
  at sun.net.www.http.HttpClient.New (HttpClient.java:306)
  at sun.net.www.http.HttpClient.New (HttpClient.java:323)
  at sun.net.www.protocol.http.HttpURLConnection.getNewHttpClient (HttpURLConnection.java:852)
  at sun.net.www.protocol.http.HttpURLConnection.plainConnect (HttpURLConnection.java:793)
  at sun.net.www.protocol.http.HttpURLConnection.connect (HttpURLConnection.java:718)
  at com.hyperion.cis.utils.HttpUtils.checkResponseCodeGood(HttpUtils.java:111)
  ... 21 more
  
  ]]
  
  
  What am I not doing?
  
  Thanks for your help in advance!
  
  Published by: VenuRamini on October 6, 2010 07:25
  
  Published by: VenuRamini on October 6, 2010 07:35

  Make sure that the Weblogic password is correct in the boot.properties and restart the services.

  Boot.properties files would be present in D:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\\security\boot.properties

  For example,.

  For APS:
  D:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\AnalyticProviderServices1\security\boot. Properties

  For Regional service:
  D:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\EssbaseAdminServices1\security\boot. Properties

  HTH-
  Jasmine.

• Problem connecting to the server

  Whenever I open the pictures, I get an alert that reads: 'there was a problem connecting to the server "my-server", which is another Mac on my network.

  If I close the dialogue box, Photos keeps trying to connect and it appears again a few seconds later.

  Does anyone have an idea as Photos is all this and how I can stop doing?

  No idea - don't forget we can not see you if you have details

  We do not yet have an idea what software you use or you use 'MyServer' for

  What are the versions of the operating system and Photos do you use? What is your server? How are you connected to it?

  LN

• Problem connecting to the server after moving

  Hi, I keep getting the message "there is a problem connecting to the server"192.168.0.19"etc. This happened after I moved. New ISP, new router. I have an Airport Express and a NAS connected to it. Time Machine and Icloud on the NAS. I think that the NAS has this IP address before moving. There are now 192.168.10.176. Everything works, but I get the pop up frequently.

  I look at the accounts and start but nothing. I reboot safe mode does not remove the problem. So, what can I do?

  I'm on Yosemite with MBR.

  Can you connect using the new IP address?

• There was a problem connecting to the server 'SERVER NAME' error guard appearing

  There was a problem connecting to the server 'SERVER NAME' error guard appearing even though the server is not on my current network.  I recently moved my iMac to a different location and a different network, and now he constantly tries to connect to the old server.  This message appears every 30 seconds and several of those who appear (see pictures) it's extremely frustrating because it makes the machine almost useless because I am constantly closing them.  No matter how many times I try to stop the activity monitor it it keeps reappearing, and I even tried a few terminal commands that I found online, then restarted the computer, but still had no success.  I would appreciate all the advice really.

  I hope that gives you an idea of what I got!

• Check error: there was a problem connecting to the server Apple ID

  When I try to connect to my iTunes on my Windows laptop account it is said there is a problem connecting to the Apple ID server. This problem did not begin until 2 days. I have the latest version of iTunes and Windows.

  What is the number of the version of iTunes?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  Start by missing error MSI.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  Leave a post by: turingtest2

  On the PC, when connecting each device, it loads a separate driver. You can try this trick when you want to get iTunes recognizes the iPhone 6. Thanks to the user of the CSA turingtest2 for the tip.

  Try the following:

  Open Control Panel > Device Manager

  Plug in your device

  Locate Bus USB Controllers > Apple Mobile Device USB Driver.
  It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.

  Right-click and select software update of the driver...

  Click Browse my computer for driver software

  Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
  C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers

  Click on let me pick from a list of drivers for devices on my computer

  Click on Apple Mobile Device USB Driver

  Click Next, then close and exit the Device Manager

  Leave a post by: ChrisJ4203

• There was a problem connecting to the network

  It identifies the network properly even when I put the password - and that is the password - the comment poster 'there was a problem connecting to the network.  The WiFi network, you are trying to reach cannot be found. "Yet he already told me that the network is correct.  Frustrated!

  Is the network that you connect to your personal or public?  On my home network, I turned on an access control and when you are trying to connect with an unauthorized device, we get similar behavior.  It does not connect despite all the correct information.

• I have a problem connecting to the internet. When I click on the internet it goes straight to windows media player

  Hi I have a problem connecting to the internet. When I click on the internet it goes straight to windows media player.

  HI Maria,

  If you are using Vista, go to http://www.mydigitallife.info/2008/06/22/reset-and-fix-broken-windows-vista-file-ext-and-type-associations-include-exe-com-sys-zip-lnk-folder-drive/ and scroll down to EXE and click or double-click it to run the program to restore EXE file associations.  Once done, do the same for LNK entry.  This should restore your programs and get the Internet icon to go to the internet rather than WMP.  If you use Windows 7, go to http://www.sevenforums.com/tutorials/19449-default-file-type-associations-restore.html. If you are using XP, go to http://www.dougknox.com/xp/file_assoc.htm.

  If this does not work and it started recently, try a system restore to a restore point BEFORE the problem started.  If you use Windows 7, see:http://www.sevenforums.com/tutorials/700-system-restore.html. If you are using Vista, see:http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/. If you are using XP, see:http://www.bleepingcomputer.com/tutorials/tutorial56.html.  If the first attempt fails, try an earlier point or two because the problem may have started before you noticed.

  I hope this helps.

  Good luck!

• "Problem connecting to the Server Web Services." - HP Envy 100

  Hello world

  I wonder if anyone has the same problem as me. I just got a HP Envy 100 and went through the process of setting up without problem. The printer is connected via Wi - Fi for wireless network, I can ping the printer from my Mac successfully and I can print within the network without problem.

  However, regarding ePrint and Web features, it seems that nothing really works. I can't even turn on Web services, I always get the message "problem connecting to the Web Services server.

  I tried the following:

  -Restart the router and printer

  -Change the manual IP address and manually set the DNS server

  -Reapply automatic IP and set the Google DNS (8.8.8.8 and 8.8.4.4) servers

  .. .with no chance whatsoever. If this is a problem with the firmware (from what I understood, I do not have the latest firmware, but I can't ask her update, because it requires, you guessed it, a connection on the server of web services, that is the whole of the problem.)

  Anyone else having the problem? Everyone had it and fixed it? Is this just a temporary problem with HP servers?

  Thanks in advance!

  Hey, for me it works as well, and I didn't, just retried that I had tried before and it connected to the Web Services without problem.

  So I think it's safe to say that the original problem in this topic only lied to a HP Server-side problem. Not cool it took so long for them to solve and in particular the fact that we did not really have feedback appropriate about the problem.

  Anyway, I solved (for now, at least).

• Problem connecting to the Windows error reporting service

  Whenever I try to check for solutions in the Windows 7 Action Center, I get the following error message: problem connecting to the Windows error reporting service. Some of the reports can not be uploaded to the Windows error reporting service. Please try again later.

  This problem began to appear a few days ago, even if I did not any changes to my computer. I do not have any firewall (with the exception of the default Windows Firewall) and all my other programs work very well on the Internet.

  Any ideas what could cause the problem?

  Problem solved.

  I actually had to purge all existing reports by using the disk cleanup utility.

• Irregular problem connecting to the wired network

  My Windows 7 PC has an irregular problem, connect to the local network of cable through a provided network of the netgear modem/router.

  The connection timeout is the question and sometimes takes a while four two minutes or more.

  A reboot of the pc never seems to resolve but (quite often, in fact usually) will be a restart of the modem.

  The modem is always on (as the announced network connection is supposed to be).

  The network provider has replaced the modem, and the problem persists. This leads me to believe that there is a start up or similar problem with the pc.

  I ran the troubleshooter in windows... no chance/results. Is there a "fixit" tool I could try or something similar?

  Happy to clarify, to provide more information and appreciate any input.

  concerning

  Lethal42

  Hello

  Thank you for your response. I appreciate your time.

  I suggest you to refer to the link below and check if this is useful:

  Wireless and wired network problems:

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1

  Hope this information helps.

  Sincerely,

  Ankit Rajput

• problem connecting to the web services server

  I tried to download the latest updates of software/firmware for my all-in-one HP Photosmart Prem C310a.

  I can't get updates or activate Web Services because it still gives me the error message "problem connect to the web services server.

  I tried everything in the section of the Web of HPs site including connection via WPS - unsucessfully problems.

  I understand that you have found impossible to connect to the server error message on your printer. I would first disconnect the router and the printer for about 1 minute. I would plug the router first then the printer. I would then try to enable web services. If not successful, and you get the same error message. I'd follow these steps.

  1 obtain the IP address of your printer
  a. This can be done by pressing the icon on the printer wireless.
  2. Enter the printer's IP address in a browser.
  3. Select the tab network at the top of the page.
  4. on the left, select network.
  5. Select Network (IP) address
  6. select manual DNS server
  a. manual Preferred DNS should read 8.8.8.8
  b. alternate DNS server should read. 8.8.4.4
  7. Select apply you could get a fair warning select OK.

• Your device blackBerry smartphones had a problem connecting to the server

  I have a Bkackberry Curve 9300

  T-mobile phone operator

  Knology is my internet

  OS 6 is underway on the BB

  What is the problem with my phone now? Usually, I get the error "this application has encountered an error and cannot continue" I want just my email in return. For the most part, I get "your device had a problem connecting to the server.

  I hope you can help.

  Kelly J

  Hello and welcome to the community!

  I suggest the following, in order, even if they seem redundant to what you have already tried (steps 1 and 2, each should result in a message to your BB to come...) Please wait for this before moving on to the next step):

  (1) registry HRT

  • KB00510 How to register a BlackBerry smartphone with wireless network

  (2) remove and return Service directories

  • KB05000 Remove the maintenance book for the BlackBerry Internet Service email account in the BlackBerry smartphone
  • KB02830 Send the directories for the BlackBerry Internet Service

  (3) restart to take batt

  • Each time a random strange behavior or slow creeps, the first thing to do is a battery pop reboot. With power ON, remove the hood back and remove the battery. Wait a minute, then replace the battery and cover. Power on and wait patiently through the long reboot - about 5 minutes. See if things return to functioning. Like all computing devices, BB suffers from memory leaks and others... with a hard reboot is the best remedy.

  I hope that will move things again for you! If this isn't the case, then you should contact TM for formal support.

  Good luck!

• T400: Error Message - there was a problem connecting to the TPM secure

  Hello

  I am a new user of ThinkPad. I just got my T400 a week ago, and I'm a fan of him immediately. But there's this little thing that really bothers me. The second day I used my laptop, I got this error message: "There was a problem connecting to the module of TPM (safety device) on this computer", and I got this message since that date, every time I turn on my laptop.  What it means? And how do I get rid of this error message? Thank you!

  Moderator Note: Type + error message added to the line object for clarity.

  go into the bios and check if the TPM secure is enabled or disabled in the BIOS. Make sure it's on. If the problem persists then call Lenovo, could be a hardware problem.