Cable from the console to SRW2048
I lost the cable to the original console to the Cisco Linksys SRW2048 and I was wondering if I can use the Cisco console cable or can a regular series with the female ends cable will work?
Thank you
Stanley
Hello, Stanley.
A cisco console cable probably will not work since they usually have a RJ-45 on one end. However, a regular serial cable should work just fine, as long as your computer has one, or you have a USB serial adapter.
The parameters for the console port are as follows:
Bits per second: 38 400
Data bits: 8
Parity: None
Stop bits: 1
Flow control: no
Once you open the connection, you will need to hit enter once something appears.
You can also check this switch via telnet console, by connecting to the IP address of switches with a telnet client and use admin as user name with a blank password.
I got most of this info to the Administrator's guide, which is available here:
Let me know if it works,
Christopher Ebert
Network support - Cisco Small Business Support Center Engineer
Tags: Cisco Support
Similar Questions
-
Need to buy a cable from the console to a SRW248G4
I have a client with an installed SRW248G4. We are unable to determine the IP address assigned to the switch and we need configure ports. The client cannot find the cable from the console provided with the unit and I succumbed to find where I can buy one. Anyone have any ideas?
Thank you!
the srw248g4 uses a regular db9 console cable. You can buy at any hardware store, just to check if the device uses a female or male.
-
Where to get the cable from the monitor to Satellite C660-1TK
I have a portable satellite c660-1tk and I have problems with the monitor, it turns out that the problem is the cable from the monitor. I went everywhere looking for a monitor cable, but I couldn't find one.
My question: where can I get one?
I thought to order it online, but can't find anything.
Hello
You can order these parts of the Toshiba authorized service provider that is available in your country.
Here is a list of all FSA available worldwide:
http://www.Toshiba.EU/innovation/generic/ASP_SUPPORT/I put t think it should be a problem to get such cable.
-
Windows 7 - how the hdmi cable from the pc to the tv
Original title: need help
How does the cable from the PC to the tv hdmi
Hi paulgibsonTF,
The problem is that Windows developers are (I think) try to be too smart - if your computer doesn't have any HDMI cable plugged into it, and you do not have a HDMI device at the other end of the cable (like a TV or surround sound amplifier / speaker system), then Windows will simply ignore the Windows software for the HDMI driver is loaded.
And even when you have a device HDMI plugged in and turned on, sometimes, Windows does not see that it is there. So don't mind allowing you to set the parameters of the device.
Now... to begin the search. Go down on the status bar (this bar on the lower edge of the screen) system and find the sound icon - looks like a small speaker. Click on it and click playback devices. On my computer, I get a window ACOUSTICS, and it only shows a device (speakers / headphones).
I don't have a connected HDMI device this time. But I do not have the device drivers loaded.
Recently, I tried to plug in this same laptop to my TV HDMI, and... of course, Windows won't see HDMI devices are there and it is plugged. Once again.
WHY? I do not know. But I had to pass by there is two years (even mobile) was about four cycles to uninstall the device HDMI driver, reinstall it, turn off things, disconnect, turn them, plug them,... and all of a sudden it started working.If Microsoft is still looking at this forum and answers other than "Windows 8", I'd love to hear them also!
http://geekitdown.com/how-to-connect-Windows-7-laptops-to-TVs-using-HDMI/
http://Windows.Microsoft.com/en-in/Windows7/connect-your-computer-to-a-TV
http://www.TomsHardware.com/Forum/324637-33-enable-HDMI-output-Windows
-
How to repair or replace the cable from the monitor on console 15fp
We bought a KVM rack and keyboard with our Dell 4210 support about 2 years ago. We have received "No Signal" for a while on the screen, and I finally had time to open the side of the basket and take a look.
I see that the insulation of the monitor cable that is built into the console monitor was rubbed through and some of the money i wire mesh has been broken. It is to the first bend of the cable guide and must have been rubbing. I guess that's the cause of the error 'no signal '.
I would like to replace the cable, but releasing the anchor on the middle of the back of the monitor seems impossible after removing all the hexagonal bolts around the perimeter. I cut the label above the dimple found in the center of the screen back but found that there is not a fastener which can be manipulated.
- Is it possible to open this beast, if I can replace the cable? I don't really have the budget for a new console.
- If it cannot be opened and closed and then after working on it, everyone is aware it is possible to connect with success a RGB cable?
Thanks in advance for any advice on this. Mike
-
Can someone help with the problems of email account? Messages from the console?
vcyman , March 9, 2016 13:16
I had ongoing issues with my Mail months including Spindumps and just doesn't look good, so I changed the e-mail settings in the past according to the directives of the ISP, but now the incoming server is grayed out, more it's time to see if my overall situation needs some changes. As I am researching the current issue of the evolution of the e-mail settings, I see the information that can be linked to a larger problem, so I'm including that in a larger context.
I use my Web site for most of my email accounts and received error messages indicating that the certificate is not valid. I contacted Hostway and learned that they have their own encryption and don't require SSL, but they said Apple mail works best if I use their specific settings instead of those I have. The server settings entering my accounts existing messaging site are shaded out and immutable. What is the best way to make changes without causing more problems?
I tried to move the mail account plist.to the trash and restart hoping that would disable the accounts but it didi not work. Or I sign out to iCloud and make changes?
MORE INFORMATION
In/Library/Application Support / Mail / Online Account Types/com.apple.updated.mailaccounts/MailAccounts.plist, the Account.plist includes an e-mail account which is Ameritech and not logged into my site.
in Library/Mail/it is V2 and V3. V2 is V2/MailData/Accounts.plist. V3 contains no Accounts.plist. in MailData. I printed the Accounts.plist. and there are 22 pages of data. Each e-mail account is repeated at least three times and it seems connected to the when I made changes to the account settings in the past.
This may be related to a larger problem because I have error messages related to the e-mail in the console.
09/03/16 12:05:22.644 PM cloudd [429]: error SecOSStatusWith:-[50] error Domain = NSOSStatusErrorDomain Code =-50 'query lack the class name' (paramErr: error in user parameter list) UserInfo = {NSDescription = query missing class name}
09/03/16 12:05:22.648 PM DCs [365]: securityd_xpc_dictionary_handler cloudd [429] copy_matching error Domain = NSOSStatusErrorDomain Code =-50 'query lack the class name' (paramErr: error in user parameter list) UserInfo = {NSDescription = query missing class name}
09/03/16 12:05:22.648 PM cloudd [429]: error SecOSStatusWith:-[50] error Domain = NSOSStatusErrorDomain Code =-50 'query lack the class name' (paramErr: error in user parameter list) UserInfo = {NSDescription = query missing class name}
09/03/16 12:05:22.649 PM Mail [634]: cannot load the draft for documentID: C265D900-C6A3-48B9-AF60-C83FE29A7AED
09/03/16 12:05:22.705 PM Mail [634]: cannot load the draft for documentID: E1D3029B-C2BF-425E-8F67-32C190B420CF
09/03/16 12:05:23.142 PM Mail [634]: CFNetwork SSLHandshake failed (-9807)
09/03/16 12:05:23.144 PM Mail [634]: CFNetwork SSLHandshake failed (-9807)
09/03/16 12:05:23.417 PM Mail [634]: CFNetwork SSLHandshake failed (-9807)
09/03/16 com.apple.AddressBook.InternetAccountsBridge [501 12:05:23.432 PM]: looking for iCDP status IDDM 61149625 (checkWithServer = 0)
09/03/16 com.apple.AddressBook.InternetAccountsBridge [501 12:05:23.435 PM]: error XPC while checking if iCDP is enabled for IDDM 61149625: error Domain = NSCocoaErrorDomain Code = 4099 "the connection to the service named com.apple.cdp.daemon was invalid." UserInfo = {NSDebugDescription = the connection to the service named com.apple.cdp.daemon has been invalidated.}
09/03/16 com.apple.AddressBook.InternetAccountsBridge [501 12:05:23.435 PM]: connection Daemon invalidated!
09/03/16 com.apple.AddressBook.InternetAccountsBridge [501 12:05:23.436 PM]: [AOSAccounts]: [__49-[ACAccountStore (iCloudAccount) icaAppleAccounts] _block_invoke]: accountsWithAccountType returned the error: Domain = com.apple.accounts error Code = 9 '(null) '.
09/03/16 12:05:23.446 PM Mail [634]: CFNetwork SSLHandshake failed (-9807)
09/03/16 12:05:23.716 PM Mail [634]: CFNetwork SSLHandshake failed (-9807)
09/03/16 12:05:24.076 PM sandboxd [139]: com.apple.Addres (501) ([501]) deny com.apple.cdp.daemon mach-search
09/03/16 12:05:24.626 PM Mail [634]: CFNetwork SSLHandshake failed (-9807)
09/03/16 12:11:40.263 Safari [624] PM: KeychainGetICDPStatus: key :-25300
09/03/16 12:11:40.263 Safari [624] PM: KeychainGetICDPStatus: status: power off
09/03/16 12:49:52.821 PM Mail [634]: * the Assertion failure in French-[IMAPParseContext _parseStatusResponse], /Library/Caches/com.apple.xbs/Sources/Mail/Mail-3112/IMAP/Connection/Responses/ IMAPParseContext.m:956
09/03/16 12:49:52.821 PM Mail [634]: exception IMAP response analysis: tried to parse a response from status without knowing the separator character.
I'd appreciate any suggestions.
Is your IMAP account?
You have stored messages slot "on my Mac"?
If create you your account in a new user, it works correctly? (see below)
See my answer in a similar debate. Let me know if you need more assistance.
Re: Certificate error. When the message appears you must choose "see the certificate", then select "always Trust ' in keychain."
CREATE A NEW USER
Go to system-> Preferences, create a new user in users and groups.
Place in the new user by logging in under the Apple in the menu bar.
Log in to the new user.
You can skip the connection with an Apple ID, unless you want to test an iCloud account. Select continue, then jump.
Open Mail and add your account. If it's a POP account, make sure that you do not select "remove copy from server after retrieving a message," on the Advanced tab.
You still see the issue?
-
iPhone 6 s is not wake up when you remove the cable from the charger.
Hi all.
I noticed that sometimes my iPhone didn't wake not (the lock screen display) when the charging cable is removed. the charger / sync port seem otherwise works normally.
Is this normal? I'm guessing that this happens because sometimes when the battery is fully charged, no power goes to the phone and if you pull the cable then, the phone can't tell you have removed the cable, but I have not seen this happen on my previous phones.
Thank you!
Yes, this sounds like normal behavior! On my iPhone 6, when it reached 100% of their capacity and is completely loaded, as it stops in charge, which is why when you unplug the iPhone from the charger the screen does not automatically wake up, because the charger stopped output power to the iPhone when it finished filling. I hope that answers your question!
-
We get an error "no audio device is installed" as he tried to use the cable from the monitor to TV
* Original title: vista home version lost his
Recently bought an Emerson TV that is has a PC plug. Hooked to the TV for the monitor cable and bought a mini audio cable with one end plugs into the speaker jack the rear of the computer and the other end of this cable is divided into a red RCA plug and a white RCA connector to the audio on the TV.
Played a movie and it displays fine but I have no sound. So everything disconnected and hooked my computer following up and my external computer speakers back up exactly as it was before still have no sound.
in the toolbar at the bottom right hand of the screen, the "speaker" icon displays red X and when I move my mouse jumper on it the message appears "no audio device is installed".
Help!
Jerry Fulkerson
Hello
You can first check in BIOS advanced settings if the onboard sound is enabled.
You can see the manual of the system manufacturer or contact the system manufacturer for more information on how to make the changes in the BIOS.
Note: changes to the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
Please follow the steps below and we update with the results.
Method 1: Follow the steps in the following article and check.
No sound in Windows
http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
Method 2: Update a hardware driver that is not working properly
Tips for solving common audio problems
http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems
Let us know if it helps!
-
Rooms disappear from the Console of the room
Hello
I have created spaces, and then sign out. Once I connect to his party. I know the House exists, but I don't see it in the console.
No help no refreshing.
It would also be nice, enter the name of a coin and enter and do not have to select in the list (in the case that I have a lot of parts)
Thank you.
.. .Russ
You are probably more than 1,000 rooms and we only list the first 1000.
I agree that we should have at least a way to choose a room or have a way to paginate between rooms. We will add it to the feature for a future release requests.
You try to access the room with RoomConsole or DevPortal? (none of them works correctly with large games room, but most of the operations available in DevPortal can be made by using the scripts on the server (which can be run from the command line) side.)
-
Local database not accessible from the console of the enterprize Manager
Hi all.. I have a strange problem, please help
I have installed hv oracle 9i on my pc. It is related to a db server and a local database (for scott schema) is also installed on the pc. with console of oracle enterprise manager, I was and want to access the two databasses. (db server and local)
I can access the database server of db as sys: attributes are...
Host: 10.4.34.59
Port: 1526
SID: grid59
attributes for local db
---------------------
Host: e5687g7665
Port: 1523
SID: ora123
the two dbs are accessible from sql plus, but when I write scott, tiger on the console, it says 'no listener'... on the net manager oracle I HAV already added the address for pc local db.
Thanks in advance, please helpHello
It's very strange, using tnsping you get the listener, so I don't understand why sqlplus returns 'no listener '.
You have run the tnsping and sqlplus from the same computer and same ORACLE_HOME, right?
You have several installed Oracle customers?Liron Amitzi
Consultant senior s/n
[www.dbsnaps.com]
[www.orbiumsoftware.com] -
Need a cable from the screen for Satego P200-15U
Hello all :)
I want to order and replace a cable for my rather old laptop screen, but I don't know the part number.
Someone has an idea of what might be the part number of this cable?
The model number is PSPBBE - 005001GR.Thanks in advance
Hello
Get in touch with local Toshiba ASP (authorized service provider)
The service partner must be able to provide a compatible cable.Here you will find all available worldwide FSA:
http://www.Toshiba.EU/innovation/generic/ASP_SUPPORT/ -
Connect a cable from the network adapter 'connection to the Local network.
My Dell Inspiron wireless lap top doesn't let me access the internet. He says to plug a cable into the adapter "Local Area Connection". When I check my counter above it says that my router is connected and working. What can I do? Thanks for any help!
Hi NancyTC,
You can read the following article and see if it helps
Wired and wireless in Windows network connection problems .
Hope this information is useful.
-
messages from the console on Simulator
Hello
I have a command line application that is simply a cost "Hello messi '... How we test the application on the blackberry playbook Simulator? How to get to see the message on the console after running the application?
We'll see all the exits to the command prompt in the display window of the IDE, but for what Console you should use an IDE.
-
No output from the console with 10.0.9
Since the update to 10.0.9 I see most any output in the console either qDebug statements. Someone knows this too and have a fix?
OK, here found information on this topic:
https://developer.BlackBerry.com/Cascades/documentation/dev/upgrading/momenticschanges.html
What a strange 'improvement '.
-
ESX3i - can I remove snapshots from the console/command line?
In ESX3i remove an instant expansion of the VI Client takes too long the client times out and appears to block all connected VI customers. Is it possible that I can delete the snapshots of the console (not supported)?
Yes, you can, just know he has not supported but works, take a look here: http://engr.ucsb.edu/~duonglt/vmware/#vmware_vimsh
vim-cmd vmsvc/snapshot.removeall [VmId] vim-cmd vmsvc/snapshot.remove [VmId] [removeChildren] [snapshotLevel] [snapshotIndex]
You can also take a look at the vCLI/RCLI utility snapshotmanager.pl http://www.vmware.com/support/developer/viperltoolkit/viperl15/doc/snapshotmanager.html
=========================================================================
William Lam
VMware vExpert 2009
Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/
If you find this information useful, please give points to "correct" or "useful".
Maybe you are looking for
-
How to activate a Broadcom Wlan on a Satellite 1130-z27
I removed the Toshiba Wlan Mini PCI card 11MBit and replaced by a 54 megabits Broadcom BCM4306-Wlan-Mini-PCI-card (many of them is sold to ebay.de).Driver is installed and accepted by Windows XP.Driver-tool says: "Radio disabled. Enable WLAN-Switch '
-
direction of the motor controlled by the adjustment wheel
How to control the direction of the engine using the adjustment wheel, for example, if the pointer locates the negative area, the engine was reversed. Usually the engine management is determined by AIN2 and AIN1 values in the microchip, if the value
-
Windows Vista Home, profile connection failure
After the opening of Windows, where try to connect me to my profile, I get this message "the service user profile Service has no connection. User profile cannot be loaded. "I'm the only Admin, so even if I try to set up a new account I can not.
-
Hello: Need to know where I can find the updated drivers for my printer OfficeJet 4500 G510n-z. I use the Windows 8.1 operating system. I tried to use the link at HP, but to the point that it supposedly gets to the install window, it asks me to ins
-
Component SelectManyShuttle is not populated with values already selected in the editing screen
Hi Experts,I use Jdeveloper 12.1.3.0.0In case my scenario, I have a screen where I select the slills as SQL, JAVA, JEE, etc for a particular job type.To implement what I have 3 tables(1) JobDetails(2) SkillDetails(3) JobToSkillMapIn the screen new cr