Similar Questions

• Sony camera detected on USB but not found (visible on the camera) images

  I plug my Sony Cybershot, I did successfully for 4 years and now, suddenly, Win7 detects the camera as usual but said there is no images - well they are clearly visible on the camera.

  "show the hidden files and folders" is perhaps not necessary, please also uncheck "Hide protected operating system files" is two or three lines under 'display files and folders '.
  apply/ok to close the window
  and please open it again to see if it resets.
  If it wasn't still not checked then check your memory card.

  Please kindly share the result.thanks

• IMAQ installed, but not found in LabView

  Ladies and gentlemen,

  We have a 2012 faculty (student) University of LabView license and want to use a digital camera with Labview. LabView has been permitted, also installing IMAQ 4.6.4 produced any errors. It is recognized by the NI Measurement and Automation Explorer as you can see in the attached PDF file.

  However, IMAQ features are not visible in the window function LabView and our VI test cannot find functions IMAQ (pages 5 and 6 of the attached PDF file.

  We reinstalled twice, LabView makes sure the antivirus has been disabled. We have also tried to install another version of IMAQ (4.6.1), but with such problems as described above.

  Today, I realized that we have a version of 64-bit Windows and LabView has 32 bits?

  Thank you very much for your help.

  Here's the most likely explanation of our problem: IMAQ 4.6.1 and IMAQ 4.6.4 are not compatible with LabView 2012:

  http://digital.NI.com/public.nsf/allkb/DB928F6D5E9D6B97862579A7006B2850

• Sought but not found blackBerry smartphones

  I searched but not found. This means that more probably I just looked in the right place.

  What I'm trying to find is the total number of contacts will hold the 8530. IE; 500? 1000?

  I know that each contact will be so numbers and an email address but how many individual contacts you can add?

  Hi and welcome to the forums!

  I have yet to see a credible source to publish current limits for the records on the calendar, Memo, tasks, or contacts apps. If you find a thanks for posting. I usually tell the users to keep it is manageable. For me 6 000 contacts? Seriously?

  Heck, I didn't was not stationed with 6,000 people in the U.S. Army. .

  Don't forget that the memory of the camera is a flash memory, which is designed to keep all functions of the device running at eye level. Storage of large quantities of documents just takes a lot of dynamics of memory and makes static.

  Let me know your opinion!

  Thank you

  Bifocals

• Corsair 3.0 slider 16 GB detected in BIOS but not in Windows 7...

  The usb works on all the other computers I tested, but not on mine. I have windows 7 Enterprise x 86 installed. In addition, it is detected in BIOS but not in windows... All solutions? Thank you.

  Hello KhurramHaider.

  I suggest that you go on the site crosair and look of the driver, if you found and installed and it STILL does not work, then there could be a problem in the operating system
  Concerning

• Why did the counter works in MAX, but not of Labview?

  Please help, I've been away from Labview for more than 3 months and I'm pretty rusty...

  Last year, I configured successfully NI9401 to measure the period (in seconds) by counting the rising edges of my sensor signal.  Since then, I bought a new PC and loaded all my software inside, including the Labview VI that has worked successfully on the old computer.

  I can see the digital signal using MAX and test for the NI9401 Panel, then, I know that my son and my TTL signal is OK, but nothing except the below error when I try to run the attached VI, happens...  How can I say this VI to search for the signal on channel 14 and MOD3/CTR0?

  Thank you. I'm sure it's a small adjustment... it worked well a few months ago... do not know what the problem is now.

  Thank you

  Dave

  OK, now.  Solved the problem. The vi is fine, but some fragile son have been identified... worked in MAX but not in vi.  Now that the connections have been tightened, it works for both.  Sorry for the inconvenience.

  Dave

• Camera works to the MAX, but not in LabVIEW

  I struggled a lot with getting a camera DCC3240M of Thorlabs working in LabVIEW. The software supplied (Thorcam) works as it should. However, the LabVIEW SDK does not work as it should, it gives an error 155 "the operation is not supported.

  Instead of the SDK software, I tried the drivers for DirectShow and now the camera arrives in MAX and works as it should. He also appears with IMAQdx list Cameras.vi and in Vision Acquisition Express vi. BUT when I try to run IMAQdx open Camera.vi or the Express vi it does not work. Open device gives a DirectShow error code 0 x 80040275 "no capture hardware is available, or the hardware is not responding." And when I try to select the camera in the express vi, a red icon is displayed and I can only choose "Cancel":

  

  It's really very annoying that the camera obviously work with the drivers provided, but I can't use it in LabVIEW.

  I would be grateful for any ideas what is wrong. I'm running LabVIEW 32 bit on 64 bit Win8.1.

  Problem solved!

  I carefully removed all the drivers that came with the camera and then I installed the drivers from manufacturers (IDS) instead of Thorlabs drivers. And now it works, the camera always appears in MAX and it does not work. But now the supplied screw. I'm so happy. It took me a week to understand.

• Attributes in NOR-Max not found in Labview

  I'm currently developing a LabView tool (2011) with a camera from Manta G504B Ethernet. It is NOR-compatible IMAQdx but in NOR-MAX attributes are not the same as those found in LabView. I would like as my tool developed to be able to change the exposure and acquire values and lifestyles. However, these attributes do not appear in LabView but appear in NOR-MAX. is it possible to get these attributes in LabView, since these values will change very frequently?

  My Manta firmware is 00.01.44.00

  NOR-IMAQ is 4.6.1

  E/s-OR-IMAQ is 2.5

  NOR-IMAQdx 3.8.1

  NOR-MAX 5.0.0f1

  Answer was found with the example OR grab and Attributes.vi base.

• Helix camera detected (front and back) not at all

  I noticed the cameras in my Helix, which had worked very well, are not dertected by Skype. So I checked the Device Manager and there is no camera detected. I downloaded the driver from the support site, and when I installed the process was interrupted once the command prompt open with the message "cannot find device." When I open the camera app, it is not detected here either.

  Everything on the forum seems to be a problem with the front or rear in front of the camera, but not both. Can someone help me with this? And if it's a hardware problem, can I have rectified in Pakistan?

  Nice day.

  Your test of Ubuntu, you may be right on a hardware failure or disconnection.

  If you do not see what is involved in the opening of the Tablet, take a look at the manual of your equipment:

  http://download.Lenovo.com/ibmdl/pub/PC/pccbbs/mobiles_pdf/helix_hmm_en_0c10337_03.PDF

  Page 54 shows the connection of the Assembly of the camera.

  I hope this helps a little.

  Kind regards.

• My integrated Webcam is recognized by MAX but not as the IMAQ device

  Hello

  I use with 2014 LabVIEW IMAQ 14 and IMAQdx14.

  I am able to use my webcame MAX both in the Vision Assistant, but when I am trying to generate vi, in the wizard, IEEE1394 Imaging is grayed out.

  When I am using triggered image acquisition and select cam0 as the name of the interface (name of my camera to the MAX), I get the error code:-1074397163 (NOR-IMAQ: the session or the interface passed is not valid.)

  In MAX, I can see and use my camera, but it appears directly in the devices and Interfaces (and not under devices NOR-IMAQ)

  I can't find out if it is compatible live show... Is this to say that my camera is not supported by IMAQ? Is there a way to check whether LabVIEW?

  Thank you

  Karol

  Hi Karol,

  Since you are able to use the camera in MAX, it is DirectShow compatible. The reason why you get this error, it is that your device is not compatible with the IMAQ driver. Instead, you should be using the driver IMAQdx and corresponding IMAQdx live. Once you use those, you should be able to control in LabVIEW. It isn't an IEEE 1394 device either, so I think that it is expected that all options for this would be grayed out. Hopefully that should get you going in the right direction, but please post again if you have problems with the generation of VI you.

  Thank you

  Katie

• USB thermometer works in Hyperterminal & MAX, but not in my VI

  I have USB (Omega TJ - USB) thermometer.  I contacted with her success in Hyperterminal.  When I try with MAX, it usually starts working after the second attempt to read/write.  But even if I put the termchar 0xD and termchar_en to True, I still have to type my writing as 'C' back ' 20.2 c ' (20.2 C being the temperature) any idea why this happens?

  In addition, I go ahead and make my VI, very similar to that found in the labview tutorial - image shown here: http://zone.ni.com/cms/images/devzone/tut/a/e09bfd41228.gif I put it for baud: 38400, 8n1.  and I also write 'c', but I get the error 1073807339.  I tried to change the buffer without change in the results.

  I thought it would be a relatively simple task, but it seems that I am bad, or overlooking something simple.

  Hi Chknrckd,

  Also what could be the problem, is that the way hyperterminal sends characters (when you type words). LabVIEW will send a string at the same time, while that hyperterminal sends each character at a time.

  More information can be found here:

  Why Test panels MAX works my Instrument Serial in Hyperterminal but not in LabVIEW or VISA work?

  http://digital.NI.com/public.nsf/allkb/171D2D70CFB66E74862571390062D12B

  I hope this helps!

• Instrument to appear in MAX, but not in the executable file

  Hello

  I use two HP34401A make some measurements, and I transfer the program to a laptop with complete labview at your desktop with only the runtime engine.  Instruments made their appearance in the Office MAX, but when I run the executable, they cannot be detected.  I expect some suggestions on how to possibly resolve this problem.

  Thank you

  Not to mention that MAX, what other driver is installed and necessary? Did you install NI-VISA, NI GPIB? At a minimum, you should include NI-VISA in the installer that you built.

• With Windows 7 or 8 on my 2710p (built in webcam), the camera driver says "HP Webcam not found"

  I had the webcam on my 2710p with Windows 7 running for a while, but after I plugged an external webcam (I think it's marked Microsoft), it's almost as if my built in webcam dissappeared.  I tried to format the computer to Windows 7 and now Windows 8 (the two 32-bit), hoping that a new facility would solve the problem, but when I try and install the driver of webcam sonix from the page of drivers hp for the 2710p (with W7 Home Premium 32 bit drivers), it says "HP Webcam has not found! Please connect the HP webcam and then run Setup again. "The only unknown device in my device manager is the PCI controller, I don't really like.

  What happens here? I'm pretty tech literate, but I'm stumped here.

  Webcams are fragile and I suspect yours is dead. I think that it is a coincidence that it happened while you were using an external webcam.

• No sound, but not found problems.

  I have no sound on my computer. I ran the fix - it tool, and no problem not found. The volume is at 100%. I am open to the control panel and go to Device Manager and opened the audio, video and game controllers to check the status of specific bequests and to search for driver updates. There is no problem with the sound on my computer, and then that I move on and search for new updates, none have been found by the computer and the fix - it tool. I still have no sound. My computer is a laptop, so there is no son to check outside. Help, please.

  I have no sound on my computer. I ran the fix - it tool, and no problem not found. The volume is at 100%. I am open to the control panel and go to Device Manager and opened the audio, video and game controllers to check the status of specific bequests and to search for driver updates. There is no problem with the sound on my computer, and then that I move on and search for new updates, none have been found by the computer and the fix - it tool. I still have no sound. My computer is a laptop, so there is no son to check outside. Help, please.

  In addition to the steps already suggested, I would recommend that you run the DirectX troubleshooter that you can access as follows:

  1. Click on start, then run (press Windows key + R if you do not "run" in the start menu) and copy / paste the following and then click OK: dxdiag
  2. Once the animation is completed loading, click on the "Sound" tab and then click on the button 'Test Direct Sound' and meet the guests accordingly.
  3. If you still hear nothing, click on the "music" tab and try to test each port. By 'port', I mean the options that are available to you which you should be able to see in the list.
  4. If the above results remain negative, click on the tab 'More help' and then click on the "Sound" button This will launch the Windows sounds troubleshooting utility where you will have a number of options to choose from.

  In case it doesn't, try to use the system restore to wind back the clock by one hour when you know that the PC was working properly, to run the system restore, follow these steps:

  1. Click Start | Programs | Accessories | System Tools | The system restore.
  2. Click the option: "Restore my computer to an earlier time" and then click Next. You will get a calendar with a certain number of Restore Points that appear in bold . Choose one where you know audio was working properly.

  System Restore takes a few minutes to run during which the PC will restart. Not to interrupt this cycle. When the PC reboots, it loads the menu of system restore, where you will see a message about whether if the restore was successful or not. Click OK to start the desktop and then try to play something to check if audio works now.

  Know that when you run the system restore, all the programs that you installed after the date that you choose to restore to will need to be reinstalled again. It goes the same for updates and security patches.

• IMAQdx attributes listed in the xml file not found in labview

  Hello

  Some attributes of my camera our watch camera (DALSA CamExpert) software but are not displayed in MAX.

  When I opened the xml file, I don't see a difference between the attributes shown and hidden.

  Why LabView displays all possible attributes?

  The sml file has specific requirements?

  Any ideas?

  Hello Eric,

  I solved the problem yesterday!

  I use a DALSA camera. Dalsa software downloads the XML file and saves it in a directory 'dalsa"on my local disk.

  National instruments software (MAX) downloaded XML file and saves it in another directory. The 2 files were not equal. I replaced the XML file OR the XML of Dalsa file and now I'm able to get all attributes.

  But thanks for your response!

  Kind regards

  Kim