Helix camera detected (front and back) not at all

Similar Questions

• The iPhone camera 6 (front and rear) and flashlight not working not

  Hello world

  I am a user of the Iphone 6 (128 GB) - purchased in December 2015. Version 9.2.1

  For two days my camera (front and back) as well as the flashlight will not work.

  • I see a black screen at the opening of the camera - can make changes to the, front/rear, HDR mode (power), etc. - but nothing happens
  • When I try to open the flashlight, it crashes (the button on our extension of the home screen is simply not lit)

  I tried to restart my phone several times, but the problem persists. Please note that nothing happened 2 days back - I have not dropped my phone, in any case I don't see that can cause damage to the camera. All of a sudden it stopped working.

  Please suggest what to do.

  To exclude a software problem, set it back to factory settings, do not use a backup, manually installed personal data and test the camera feature.

  Use iTunes to restore your device to factory settings - Support Apple iOS

  If the device works, restore the backup of the data. If the device still does not work, you will need to get the phone checked by Apple a Service provider authorized Apple to air:

  Apple iPhone - contact Support - support

• M1536dnf adf scanning front and back is possible?

  Hello, just a simple question on the HP LaserJet Pro M1536dnf.

  Before buying, I'm trying to understand whether it is possible to analyze front of documents using the ADF (automatic document feeder).

  I tried to read the manual a bit and it seems, it is possible to automatically print duplex (front and back), but it is not clear whether it is also possible to scan duplex.

  To make it even clearer: if I need to scan 10 pages which are printed front and back, can I place these 10 pages in the feeder and scan automatically in a single pdf document?

  If not, can I at least automatically scan one side of these pages and then reverse the entire block of pages and scan again for the back? And there at - it software or something (supplied with the product) that merges the pages scanned in order to make a single pdf file where pages are placed in the correct order?

  Any help appreciated, thanks!

  Hello

  M1536 series provides no ADF Duplex scanning, only print double-sided.

  Software will scan a face in a work of unique analysis only and do not provide an option to merge multiple analytical work into a single file.

  The Officejet Pro 8500 has more (A910g) as example can perform the required task, however it is ink jet and not one laserjet printers. None of the consumer Laserjet models provide all of the ADF duplex features.

  I hope that someone that more familiar with commercial Laserjet MFP will be able to direct you also.

  Kind regards

  Shlomi

• How can I print front and back (double-sided)?

  I hope someone can help me... it's a very simple procedure that I do not know how to do it on the new vista software! Help! Everything I need to know how to do is printed on the front AND back. In my office, no one can understand it... Help, please!

  This is a question for the manufacturer of the printer - printing on two sides of a sheet of paper is usually controlled by the printing software and drivers.  As you don't know the brand, model and version number of your printer, I can't provide you with a link to their support site (but it should be pretty easy to find).

  Here is a generic article on printing double-sided in Windows: http://www.ehow.com/how_2253127_print-double-sided.html.

  Here is another article on printing double-sided in general (the configuration of the laptop) and in Word and WordPerfect: http://www.law.duke.edu/computing/printing/doublesided.

  Here's a last article on how to print two-sided manually (assuming you do not have the equipment to do it automatically): http://h71036.www7.hp.com/hho/cache/548309-0-0-225-121.html.

  I hope this helps.

  Good luck! Lorien - a - MCSE/MCSA/network + / A +.

• How to add a Groove to the page front and back?

  I already created my front and back pages with a spline, but now the printer says they need with a Groove of 10mm for the back and the front pages.  I have no idea how doing this and can't seem to find any mention of adding to my design.

  Please, I would be very grateful if someone could help me with this.

  Thank you very much

  Susan

  Just to note - the picture of the book, the Groove refers to the line on the front cover (not the fold on the side).

• by aligning the front and back of the cards to collect

  I designed a model of 2.5x3.5 9 cards to Exchange, but when I take it the printer front and back are not aligned. Can someone help me to align the front and back. When I print on my printer, they seem well but when I take them to printing, the alignment is off. Need help!

  It's weird.

  What is the difference?

  Viewing at 100% in Photoshop?

  You provide the printer with a PDF file?  (I had some strange things happen with PDF on more than one occasion.)

  Did you use guides to align layers/objects?

  You flatten the output file?

• HOW TO PRINT THE FRONT AND BACK (DOUBLE-SIDED)?

  How can I print on the front and back? Help, please!

  Hello

  It depends on the software and the printer you are using.

  Probably best to check with the manufacturer for these two and the specific forums Support.

  If it's in a program Office control with the Experts of the Office here: (re - ask your question in the appropriate groups)

  Office newsgroups
  http://www.Microsoft.com/Office/Community/en-us/FlyoutOverview.mspx

  Discussions in the Office Setup program
  http://www.Microsoft.com/Office/Community/en-us/default.mspx?DG=Microsoft.public.Office.Setup&lang=en&CR=us
  Or

  Welcome to Microsoft Discussion groups
  http://www.Microsoft.com/communities/newsgroups/list/en-us/default.aspx?GUID=1A61081E-1F66-5F7F-B5BA-04767E55A63B

  Microsoft.public.office.setup discussions
  http://www.Microsoft.com/communities/newsgroups/list/en-us/default.aspx?DG=Microsoft.public.Office.Setup&cat=en_us_642d5640-c1ba-43C3-A224-b3ec1473346c&lang=en&CR=us

  Printer manufacturer you will also Support, documentation online and possibly forums for help.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• PC Windows Vista stops unexpectedly. Sometimes several times a day and sometimes not at all.

  My Windows Vista PC completely stops unexpectedly and without warning. Sometimes several times a day and sometimes not at all. When I turn it back on, sometimes I have a blue screen that tells me that the PC has experienced an unexpected shutdown and communicate with my local technician. However when turning on, I am always able to return to my office. My anti-virus support told me that it is not related to a virus. Help!

  It is likely some equipment or device driver issue (although we can not entrierly a problem of software).  I need a lot more information on this blue screen - EXACTLY what it says Word for Word with all the codes.  Read the messages and follow the procedures established by the MVP of the spirit in the following thread on the Blue Screen of Death.  They should help you solve your problem. http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/8cd8362e-7d06-46FB-afd7-84d54b6a8ea7  I know it's long but a blue screen problems problem may take some time because there are so many different causes and we must find the right to try to identify the problem and then find a way to fix it.  One of the elements in his post is a method to prevent the system to reboot when a blue screen if you have the time to copy the information.  If the system is not turned off, but the screen does not stay up long, press prtscrn to copy the screen, then when the system boots to open Microsoft Paint, click on the Open box and click Ctrl + V to paste here you have plenty of time to copy the information and post it here so we can look at.  Do not forget to include EVERYTHING - it is unclear what could be of crucial importance.

  I repeat the procedures in the messages of the spirit in the link above - just follow them and answer back here with the results.  Want to make interim reports before the end of the stteps is perfectly OK - in fact, I suggest you do that so I can help guide you and maybe eliminate some of the steps because they will provide no information, that we don't already know (or will not solve the problem because of the information that we already know.

  A question, is your so hot PC anywhere on it that if you hold your hand on it, you will need to detach due to heat?  Overheating is a common cause of this type of problem.  Check that the fan doesn't work and all intake and exhaust ports are clean of dust, lint, or any other obstacle.  If this is a desktop computer, remove the cover and clean the entire interior to remove dust and lint and anything else that doesn't belong.  Make sure you do not loosen or detach the wiring or the accessories cards or RAM chips.  Don't bother if it's a laptop - it's too difficult to get inside to do a proper clean-up - just make sure that the fan is running and that the vents are clear.

  I hope this helps.  I look forward to your reply with your comments about what you did to the spirit and procedures for detailed information on the blue screen error.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How can I print a doc pdf A3 (one page only) on A4 format (single page) front and back (duplex printing actual size) without size reduction?

  Printing should come half real size on front and one on the back of the A4 paper.

  Hi fane,

  That is not possible without size reduction. It may not be possible at all.

  Kind regards

  Ajlan Huda.

• diplay is superior to the front and back screen

  original title: need help with the appearance

  My kids were playing on the computer and before my windows fit perfectly, but now everything is bigger and do not fit properly. How can I fix it? I have tried everything I know!

  Right click on a space empty on your desktop and select Properties.
  Click the settings tab.
  Drag the "Screen Resolution" slider to the right.  Do it slowly until you get the look you like.

• create a features front and back in as2

  This is my current code and I would like to include a feature front and rear, all ideas would be received with gratitude?

  Thanks for help.

  AS3 newbie!

  Import mx.transitions.Tween;
  Import mx.transitions.easing. *;

  totalPictures = 19;
  Close._visible = false;

  function showThumb (target) {}
  Close._visible = true;
  thumbsHide();
  loadTarget (target);
  disableThumbs();
  }
  function closeThumb() {}
  Close._visible = false;
  thumbsShow();
  enableThumbs();
  }

  function disableThumbs() {}
  for (i = 0; i < = totalPictures; i ++) {}
  thumbs ["BTN" +(i+1)] ._visible = false;
  }
  }

  function enableThumbs() {}
  for (i = 0; i < = totalPictures; i ++) {}
  Pictures ["MC" +(i+1)] true = false;
  }
  
  for (i = 0; i < = totalPictures; i ++) {}
  thumbs ["BTN" +(i+1)] ._visible = true;
  }
  }

  function thumbsHide() {var myTween:Object = new Tween (thumbs, "_alpha", Strong.easeOut, thumbs._alpha, 0, 0.5, true) ;}}
  function thumbsShow() {var myTween:Object = new Tween (thumbs, "_alpha", Strong.easeOut, thumbs._alpha, 100, 0.5, true) ;}}

  function loadTarget (target) {}
  var myTween:Object = new Tween (photos ["mc" + target], "_alpha", Strong.easeOut, photos ["mc" + target] ._alpha, 100, 0.5, true ");
  }

  function closeTarget() {}
  for (i = 0; i < = totalPictures; i ++) {}
  var myTween:Object = new Tween (photos ["mc" + i], "_alpha", Strong.easeOut, images ["mc" + i] ._alpha, 0, 0.5, true ");
  }
  
  closeThumb();
  
  }

  {nextBtn.onRelease = function ()}

  currentTarget = (currentTarget + 1) % (totalPictures + 1);

  showThumb (currenttarget);

  }

  {previousBtn.onRelease = function ()}

  currentTarget = (currentTarget + totalPictures) %(totalPictures+1)

  showThumb (currenttarget);

  }

  function showThumb (target) {}

  currentTarget = target;
  Close._visible = true;
  thumbsHide();
  loadTarget (target);
  disableThumbs();
  }

  etc...

• None of my audio jacks do not work. Front and back (office)

  Recently, I connected my desktop computer for an amp with an attachment to a rope to get sounds. It's a beefy amp and I don't have all the sound cards in addition to that on the motherboard. After that I connected and discovered, he did not. No audio jacks working now and I reinstalled Realtek HD Audio Manager twice and no solution. How can I fix this to get the worksheets?

  Hi MitchellCochran,

  1. have you disconnected the amplifier on the computer and still there is no sound on the computer?

  2. you receive a message on the audio device works is not on the computer?

  Method 1

  Check and make sure that the correct audio device is set as default.

  (a) click the Start button and then click Control Panel. In the search box, type sound, and then click sound.

  (b) click on the read tab, and then look for audio devices. These appear as icons of the speaker and are labeled as speaker, track of the names of the devices.

  If you have multiple devices, the default device has a check mark next to it and is labeled as default value.

  (c) if the wrong audio device is listed as default audio device, click the correct audio device, click set as defaultand then click OK.

  Change the audio device may require that restart you your computer.

  Method 2

  If fails it above step then check out the link below and run the troubleshooter of audio playback, check if it helps.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

• Camera detected in MAX, but not found in Labview

  Hello

  I have a camera Thorlabs USB (DCC1645C). I installed the drivers and MAX detects the camera, but when I try to open the camera with NOR-IMAQdx, it does not appear. I also tried to open with NOR-IMAQ camera, but I could not.

  If I try with Vision Express/Vision acquisition, the camera appears, I am able to select and configure the principle of the camera, but when I execute the program there a mistake: 'not found room '.

  It would be great help.

  Thank you

  Hi AurelioSilva,

  In fact, NI-IMAQ driver is used only for materials. For the hardware part 3 (such as your USB camera), I recommend the use of iMAQdx. You can find the difference between the iMAQ and iMAQdx here: http://digital.ni.com/public.nsf/allkb/0564022DAFF513D2862579490057D42E

  Now, back to your problem. When you talk about LabVIEW 2013 (64-bit), I think that it is perhaps the issue. You see, most of the drivers like iMAQdx and iMAQ are supported by LabVIEW 2013 (32-bit) only. Don't worry, you can install and run 32-bit LabVIEW 2013 in your 64-bit computer OS cause I do this all the time with 3rd party cameras. In short, not all drivers of OR are supported on a 64-bit version of LabVIEW. You can read about it here: http://digital.ni.com/public.nsf/allkb/E9B4EA0143514DCB8625725D0050680A

  Warm greetings,

  Lennard.C

• Double-sided printing. The different margins top, front and back

  I'm tying to print the aWord 2013 document on A4 sheet, double-sided, on my envy of 7640, now my Windows 10 pc.

  I played with different sizes of margin and sometimes the text at the top of the page is missing or text starts at least 30 mm from the top of the cover page. Still back starts about 7-8mm from the top of the printed page.

  I can't say with certainty that it is since the free update of Windows 10, but he printed double-sided OK in the past.

  I have not modified parameters, only diversity of margin sizes when creating documents.

  Hi @crag67,

  I understand that when you print from 2013 of Word by using the duplex function, the margins on the front of the page and the back of the page are different. This happens when you print from other programs or just the word? If it occurs with other programs, it could be the driver, but if it occurs only when you print from Word, Word or a framework within the program, in which case I suggest reaching out to Microsoft or the Microsoft community.

  If this problem occurs when you print from several programs, we will remove the driver and re - add new.

  I suggest to use the following steps to remove the printer from the device and printers and the driver from the properties of the server.

   

• Sony camera detected on USB but not found (visible on the camera) images

  I plug my Sony Cybershot, I did successfully for 4 years and now, suddenly, Win7 detects the camera as usual but said there is no images - well they are clearly visible on the camera.

  "show the hidden files and folders" is perhaps not necessary, please also uncheck "Hide protected operating system files" is two or three lines under 'display files and folders '.
  apply/ok to close the window
  and please open it again to see if it resets.
  If it wasn't still not checked then check your memory card.

  Please kindly share the result.thanks