Attributes in NOR-Max not found in Labview

Similar Questions

• Camera detected in MAX, but not found in Labview

  Hello

  I have a camera Thorlabs USB (DCC1645C). I installed the drivers and MAX detects the camera, but when I try to open the camera with NOR-IMAQdx, it does not appear. I also tried to open with NOR-IMAQ camera, but I could not.

  If I try with Vision Express/Vision acquisition, the camera appears, I am able to select and configure the principle of the camera, but when I execute the program there a mistake: 'not found room '.

  It would be great help.

  Thank you

  Hi AurelioSilva,

  In fact, NI-IMAQ driver is used only for materials. For the hardware part 3 (such as your USB camera), I recommend the use of iMAQdx. You can find the difference between the iMAQ and iMAQdx here: http://digital.ni.com/public.nsf/allkb/0564022DAFF513D2862579490057D42E

  Now, back to your problem. When you talk about LabVIEW 2013 (64-bit), I think that it is perhaps the issue. You see, most of the drivers like iMAQdx and iMAQ are supported by LabVIEW 2013 (32-bit) only. Don't worry, you can install and run 32-bit LabVIEW 2013 in your 64-bit computer OS cause I do this all the time with 3rd party cameras. In short, not all drivers of OR are supported on a 64-bit version of LabVIEW. You can read about it here: http://digital.ni.com/public.nsf/allkb/E9B4EA0143514DCB8625725D0050680A

  Warm greetings,

  Lennard.C

• IMAQdx attributes listed in the xml file not found in labview

  Hello

  Some attributes of my camera our watch camera (DALSA CamExpert) software but are not displayed in MAX.

  When I opened the xml file, I don't see a difference between the attributes shown and hidden.

  Why LabView displays all possible attributes?

  The sml file has specific requirements?

  Any ideas?

  Hello Eric,

  I solved the problem yesterday!

  I use a DALSA camera. Dalsa software downloads the XML file and saves it in a directory 'dalsa"on my local disk.

  National instruments software (MAX) downloaded XML file and saves it in another directory. The 2 files were not equal. I replaced the XML file OR the XML of Dalsa file and now I'm able to get all attributes.

  But thanks for your response!

  Kind regards

  Kim

• Resource not found. -LabVIEW error code load 3

  LV2011 XP SP3

  I created an executable of LabVIEW by using a party lvlib 3rd screws (the screws in this lvlib are only stdcall (WINAPI) CLFs.)

  After you have installed the RTE of LV 2011 on the target computer, I copied the .exe and the necessary support files. When I try to run the executable, I get the following errors for each VI used from the 3rd party lvlib:

  LabVIEW: Resource not found.
  Error loading VI 'thirdParty.lvlib:any.vi '. LabVIEW support 3 error code: could not load façade.

  This 3rd party lvlib is included in the application under dependencies Builder. In addition, none of the screws to have their facades open. (They have the appearance of the default window properties). I also installed the thirdParty.lvlib on the computer target in the same directory structure that the Application Builder uses. (It is interesting that the DLL is taking in charge the CLFs in part 3 lvlib live)

  Any thoughts?

  Screws serving as the library would automatically be included in the executable, so there's no need to install the library on the target computer. It seems to me that you have a missing dependency for the DLL. Perhaps, the DLL requires another DLL? Where is placed the DLL?

• IMAQ installed, but not found in LabView

  Ladies and gentlemen,

  We have a 2012 faculty (student) University of LabView license and want to use a digital camera with Labview. LabView has been permitted, also installing IMAQ 4.6.4 produced any errors. It is recognized by the NI Measurement and Automation Explorer as you can see in the attached PDF file.

  However, IMAQ features are not visible in the window function LabView and our VI test cannot find functions IMAQ (pages 5 and 6 of the attached PDF file.

  We reinstalled twice, LabView makes sure the antivirus has been disabled. We have also tried to install another version of IMAQ (4.6.1), but with such problems as described above.

  Today, I realized that we have a version of 64-bit Windows and LabView has 32 bits?

  Thank you very much for your help.

  Here's the most likely explanation of our problem: IMAQ 4.6.1 and IMAQ 4.6.4 are not compatible with LabView 2012:

  http://digital.NI.com/public.nsf/allkb/DB928F6D5E9D6B97862579A7006B2850

• Addition of NOR-9223, not found

  Before I have the hardware, I'm trying to build my project and compile my FPGA (just to make sure I'm sizing properly my FPGA).

  I've selected a cRIO-9064 and trying to add a NEITHER-9223 cSeries, but there is not in the drop-down list cSeries. Shouldn't be able to add this? I'm running SP1 2014 LabVIEW RT 14.0.0, FPGA 14.0.0 and 14.5 OR RIO.

  Thank you

  Craig

  Found! I was trying to add the c series of the controller module rather than add to the chassis. Of course, a module able to acquire 1 ms/s does not use the scan interface so the only place to add it would be on the target FPGA not the target of RT.

• CompactRIO Deploy Error "LabVIEW: resource not found.»

  Hello

  I use a 9002 CompactRIO and LabVIEW 8.5.  I made a simple FPGA VI to read a bunch of analog inputs and write a square wave to a few analog outputs.  Then, I made an another VI to run on the target in real time in order to convert the frequency scaling and updated entries nationwide cycle duty cycle values and frequency real accountability.  When I try to deploy the VI in real time, I get the following:

  Deployment r03fsae (the goal settings successfully deployed)
  Deployment of special audit Tags.vi (5.89 K)
  Deployment GetRTHostConnectedProp.vi (3,41 K)
  Deployment of search and replace Pattern.vi (8,11 K)
  Deployment nirviFillInErrorInfo.vi (8.09 K)
  Deployment niLvFpgaErrorClusterFromErrorCode.vi (11.27 K)
  Deployment nirviErrorClusterFromErrorCode.vi (5.93 K)
  Deployment error Code Database.vi (3.67 K)
  Deployment to find Tag.vi (10.43 K)
  Deployment of fusion Errors.vi (6.75 K)
  Deployment Whitespace.vi topping (3.71 K)
  Deployment nirio_MultilineStringToArray.vi (8,81 K)
  Deployment nirio_AppVersionToI32.vi (3.96 K)
  Error error Code.vi (23.42 K) Cluster deployment
  Deployment _nirio_device_attrSetString.vi (9.46 K)
  Deployment _nirio_device_close.vi (9.90 K)
  Deployment nirio_Read32.vi (13,07 K)
  Deployment _nirio_device_open.vi (11.59 K)
  Deployment nirio_Write32.vi (13,01 K)
  Deployment _nirio_device_writeBlock8.vi (9.83 K)
  Deployment nirio_Write8.vi (13,01 K)
  Deployment _nirio_device_configSet.vi (11.42 K)
  Deployment nirio_DMAReconfigureDriver.vi (16.63 K)
  Deployment _nirio_device_writeBlock32.vi (9.36 K)
  Deployment nirio_Read8.vi (13.04 K)
  Deployment nirio_DMAStopAll.vi (11,39 K)
  Deployment _nirio_device_attrGetString.vi (13.06 K)
  NirviReportUnexpectedCaseInternalError (String) (5.58 K) .vi deployment
  Deployment of .vi nirviReportUnexpectedCaseInternalError (U32) (4.72 (K)
  Deployment _nirio_device_readBlock32.vi (14.41 K)
  Deployment _nirio_device_attrGet32.vi (13.85 K)
  Deployment nirio_IsItOKToDownload.vi (7.07 K)
  Deployment nirio_MiteNTDeviceFamily.vi (5.30 K)
  Deployment of Format Message String.vi (7.35 K)
  Deployment CORE.vi General Error Handler (51,02 K)
  General Error Handler.vi (13.19 K) deployment
  Simple deployment Error Handler.vi (10.01 K)
  Deployment nirio_CheckDriverVersion.vi (10,58 K)
  Deployment _nirio_device_attrSet32.vi (13,62 K)
  Deployment nirio_Download.vi (29,31 K)
  Deployment nirio_ConfigureRegisterAddresses.vi (7.11 K)
  Deployment nirio_CleanUpAfterDownload.vi (6.22 K)
  Deployment nirio_PrepareForDownload.vi (6.44 K)
  Deployment nirio_EnableInterrupts.vi (13.76 K)
  Deployment nirviRIOSetUpMiniMite.vi (31.23 K)
  Deployment nirio_Open.vi (14.93 K)
  Deployment nirio_Close.vi (10.95 K)
  Deployment nirio_DisableInterrupts.vi (11,10 K)
  Deployment of nirviIntfOpen_cRIO - 9102.vi (85,54 K)
  Deployment of nirviIntfClose_cRIO - 9102.vi (12.24 K)
  Deployment of scale freq and duty.vi (4.46 K)
  Deployment XDNodeRunTimeDep.lvlib
  Deployment XDNodeRunTimeDep.lvlib:loadlvalarms.vi (5.47 K)
  Math.vi sensor deployment
  Could not download the math.vi sensor
  LabVIEW: Resource not found.
  LabVIEW: Resource not found.
  LabVIEW: Resource not found.
  LabVIEW: Resource not found.

  Download completed with errors.

  This error message is not particularly useful, someone knows what could be my problem?  Or how I can fix it yet?  Is there a detailed journal where I can look for more information about the error?

  Thanks in advance for any help!

  Hi David,

  You may be walking on ground dangerous with your fpga code, old and new.  You use the modules in what is known as 'calibrated' calibration mode that is of fixed point math.  Your generation of square wave fpga using whole math, which is normally used when the modules operate in mode calibration "gross". To change the calibration mode, you will need to right click on the module, then select it desired mode to use.  I'm not saying that you do.

  What you need TO do to ensure the proper functioning of your fpga VI is to make sure that you use U32 son of math required and then convert the U32 an FXP using the correct encoding (if it is signed, word length and integer).  In your case the 9263 requires signed word in length, 20-bit, 5-bit all over.  Insert an FXP conversion between the generation of square wave and either create a constant FXP of the appropriate type (or use a control correctly put in place of one of the other 9263 channels [AO0 AO1]) and connect to the node of type of fixed point on the conversion OR define the conversion of fixed point with a right click on the exit node and the appropriate settings in the popup box.

  As for your new code fpga, I don't know why you used a sequence structure that your reading of 18 channels on the 9205 will have 144 microseconds, and each write two channels on the 9263 will take 5 microseconds.  I've not worked on how long will take the square wave generation.

  I do not understand your last question.

  > "I've attached a screenshot of my pwm_out.vi if I remove control of read/write of background, or if I don't use of all none of the analog inputs, it works fine.

  > But as soon as I add the analog inputs it fails... ».

  Did you create a new stream of your fpga_new.vi and referenced in your pwm_out_new.vi on the RT?

  It is difficult to guess what you are showing in the screenshots.  If the project is not too big then maybe you could post here.

  As mentioned above, by JMoto, software versions help.  Check in MAX you have on your PC and also on the cRIO 9002 to make sure that there is no incompatibility.

  See you soon

  Stephen

• Houston-25058: type attribute Definition is not found in

  JDeveloper - Studio Edition Version 12.1.3.0.0

  Migration project 11.1.1.5 ADF - > 11.1.1.7-> 12 c.

  No problems during the migration and everything works fine (apart from a problem of Javascript).

  Now in the 12 c environment, I created a new application (library) and I am facing the slot issue during execution;

  Houston-25058: xxx attribute type Definition is not found in xxxx

  1. I have 3 of VO and all 3 have the same evaluation office, tables and joins etc.

  2. for VO 2 of his works fine, but 1 of the VO throws exceptions.

  3 cross checked EO to VO to PageDef, throughout all the way all the attributes and references exist.

  4 BC4J Tester works fine, no exception for the VO above with NAV and Associations etc.

  Anyone falls on this?

  (CE mark as answer since I resolved the issue and I managed to progress)

  Subramanian

  Thanks for the elaborate response.

  I want to answer all of your questions, but I managed to deal with that, ok. nothing smart or technical, what I did is recreated a new (exactly the same thing until the last attribute of layout) create VO, LIKE, VL and declarative added page, exactly how I did before, that's his work... to be honest I never thought that it will work.

  Now, this behavior triggered a few other questions: -.

  1. I created 2 sets of features exactly the same way and it works and is not another?

  2 can we do something with the new JDeveloper 12 c?

  3. If this type of behavior will happen at the average / towards the end of the development, I can't recreate / restart never time, due to the complexity of the feature?

  Any thoughts?

  See you soon,.

  Saran.

• MAX finds a camera but Labview IMAQdx gives the error-1074360311: camera not found

  Somehow Labview does not seem to see what is happening in the measurement and automation Exploerer (MAX).  MAX works very well and my camera plugged into a card PCIe-1433, works very well.

  LabVIEW sees it not at all.  Session commands are empty, the enumeration cameras VI IMAQdx returns an empty array and all calls to open, snap, seize or close the interface (I use the name of the interface of MAX because session orders will not autopopulate) give all the-1074360311 error: "Camera Not Found".

  Somehow Labview does not MAX.  I tried to delete all the .idd files and recreate them, with the same results.

  Here are some details:

  LabVIEW 2011 (11.0.0)

  Module Vision Development 11.0.0

  IMAQdx 3.8.1

  IMAQ 4.6.1 is also installed

  The only other references I found for it is here: http://forums.ni.com/t5/Machine-Vision/camera-not-found-imaqdx/td-p/1323861/page/2 but it is more info on not opening properly references rather than do not find them at all.

  Any suggestions would be very useful,

  Casey

  I think it's because you use IMAQdx rather than IMAQ. All framegrabbers nor (for example the 1433 you use) are supported by the API IMAQ, not IMAQdx. You should be able to open the IMAQ examples instead, and I suspect that will solve your problem.

  Eric

• NOR-MAX recorded do not channel setting correctly

  I'm developing a system using Modules of field Point. I use 7 LabVIEW and NOR-MAX 3.0 to create commands and attributes for the FP-PG-522 module.

  To create an attribute of channel using NOR-MAX 3.0, I selects the FP-PG-522 module in the section of remote systems, select the desired channel, select the string attribute, then select Create point.

  A new item now appears in the data area. When I select this element, there is a description in the section 'Channels used on this point', which describes the attribute. For example, I chose the market time attribute. For this article, it says "this element represents the 'On Time' of the channels selected attribute. This attribute can be set to any integer between
  1 to 65535. "

  Then, I hit the SAVE button, which shows how to save the IAK file locally, so to save it on the module of ps2000.

  If I close OR-MAX 3 and restart, when I select the same new element in the data area, the attribute has changed. It doesn't seem to be any pattern, but I had such combinations as the "control" attributes, instead of the attribute "Generate impulses", etc..

  Then I have to delete all these channels and start again, however, data are still once, not saved correctly.

  Someone else knows this and knows a way around it?

  Chris,

  This problem has been identified and the fix will be included in the next version of FieldPoint software.

  I just wanted to let you all know.

• GPIB do not list in LabVIEW but ranked in MAX

  Hi all

  I connected to my Yokogawa WT3000 by NI GPIB-USB converter.  His listed to MAX (GPIB1::1:INSTR).  But it is not listed in LabVIEW (resource VISA control).  When I tried "Open Panel Test of VISA", Max sound raise an error "VISA_ERROR_RSRC_NFOUND."  At the same time when I try to 'Communicate with Instrument', the device responds to commands.  So, I came to an agreement leading to the GPIB commands is communicated correctly with the instrument where as orders VISA is not provided with the instrument.  When I looked into VISA Interactive Control, the device is listed as unknown.  Can someone help me to list the instrument in LabVIEW (resource VISA)?

  

  

  

  

  Thank you

  Ajayvignesh.

  The problem is resolved.

  The cause of the problem is because of these two GPIB-USB and the instrument used the same address "1".

  In the "GPIB1::1:INSTR" address, Word of firs is GPIB-USB converter address and the number of the Middle: 1: is the address of the instrument.

  In max, you can change these addresses in MAX as an administrator.  A few times, even running as administrator will not allow you to change this address, then you must restart the PC to activate the edit mode.

  Once you have changed this address with different numbers for the Instrument as 'GPIB2::1:INSTR' and GPIB-USB, it works very well and whose list of Visa LabVIEW resources.

  Thank you

  Ajay.

• labVIEW: resource not found. When you run executable

  Hello

  I had a fully functional vi with LabVIEW 2009 (continued from developer) and must be able to run it on another PC without him.  I downloaded LV Run-Time 2009, but when I try to run the executable I built, I get an error that reads:

  LabVIEW: Reasorce not found.

  An error occurred loading VI ' NI_AALPro.lvlibderivative x (t) .vi '.

  LabVIEW support 3 error code: could not load before panal.

  I can run the executable on another PC with LabVIEW without problem.  I read somewhere on the need to stop the front panal beng removed on void screws with Application Builder, although I don't think I have.  I apologize in case this is a stupid question, and I appreciate any help.

  See you soon

  Luke

  In the Project Explorer, click with the right button on the construction specifications and select new > Installer.

• Image of the attribute: file is not found in the list of the packaged files:

  When Build in Webworks already, I still have the following 2 lines in the config.xml file, but it said ' image of the attribute: file is not found in the list of the packaged files.

  
   

  My full config.xml:

  
  "xmlns ="http://www.w3.org/ns/widgets "
  xmlns:CDV ="http://cordova.apache.org/ns/1.0" > "
    CarlogPro
    Service and gas logs
    http://Cordova.IO "> XpertLulu"
   
   
   
   
    subdomains of http://xpertlulu.com"="true"/ >
   
   
  

  Need help!

  Nevermind, I've upgraded v2.0.0.54 to v2.0.0.71 Webworks and it worked.

• Child view attribute - Instance of undefined problem or view not found

  Hello!

  I was following a line example in creating a master page / detail in jdeveloper/OPS. Everything was going smoothly until I reached the stage where I'm to define a master table region (Style of the region: advancedTable). In the section of BC4J, he lets me pick my masterVO1 in the list (in collaboration with detailsVO1, detailVO2) but it gave an error when I push on the choice in the attribute of child mode - display attributes can not be recovered. View not found or indefinite instance.

  I defined in AM my opinion forums (masterVO1, detailsVO1, detailsVO2) and the view binding instance. What do you think went wrong?

  Thank you.

  Jon

  Hello

  You can try to skip this part.

  Just add:

  View instance, view detail and ViewLink attribute.

  BR, 906099

• Definition type attribute not found in CompNameLOV COMPETENCE_CLUSTER

  Hello

  I get the error message like "COMPETENCE_CLUSTER of definition of the attribute type is not found in the CompNameLOV '...

  When I extend the VO LOV and added three transient attributes in this... The entire process well... even the table JDR_PATHS showing the vo seeded has expanded, but changes do not think...

  Please suggest...

  Kind regards

  Praveen

  Hello..

  His view and view Instance value attribute would not put.