Cannot access asdm of VPNs

Similar Questions

• Cannot access ASDM on 5505

  I'm new to the forum/discussions so forgive me if this is already posted. I read through various posts and followed troubleshooting in them, but I can not even access ASDM. I deleted the old ASDM versions and upgraded to ASDM 7.1 (1) 52 that shows compatible with ASA 8.2 (1). I am inside a NAT address connected to Eth 0/5, 192.168.1.5/24. I can ping and SSH for the FW but no ASDM. FW going traffic and all the rest works fine. Please notify. Thank you.

  JEREMY - ASA # display the worm

  Cisco Adaptive Security Appliance Version 8.2 software (1)

  Version 7.1 Device Manager (1) 52

  JEREMY - ASA # display running asdm

  ASDM image disk0: / asdm-711 - 52.bin

  don't allow no asdm history

  JEREMY - ASA # http see race

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  JEREMY - ASA # show run

  : Saved

  :

  ASA Version 8.2 (1)

  !

  JEREMY - ASA host name

  enable the OMIT encrypted password

  OMIT encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 134.121.11.153 255.255.248.0

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  banner exec

  OMIT BANNER STATEMENTS

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  permit same-security-traffic intra-interface

  outside_access_in deny ip extended access list a whole

  pager lines 24

  Enable logging

  timestamp of the record

  logging asdm-buffer-size 250

  logging trap information

  asdm of logging of information

  forest management - ipaddress outside device id

  host of logging out to OMIT

  Outside 1500 MTU

  Within 1500 MTU

  IP verify reverse path to the outside interface

  IP audit attack action fall

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ASDM image disk0: / asdm-711 - 52.bin

  don't allow no asdm history

  ARP timeout 14400

  Global interface 10 (external)

  NAT (inside) 10 192.168.1.0 255.255.255.0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 134.121.15.254 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA authentication enable LOCAL console

  AAA authentication http LOCAL console

  LOCAL AAA authentication serial console

  the ssh LOCAL console AAA authentication

  LOCAL AAA authorization command

  LOCAL AAA authorization exec

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Telnet timeout 5

  SSH 192.168.0.0 255.255.255.0 inside

  SSH 192.168.1.0 255.255.255.0 inside

  SSH timeout 10

  SSH version 2

  Console timeout 0

  management-access inside

  a basic threat threat detection

  threat detection statistics

  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200

  NTP server FAILED

  Des-sha1 encryption SSL

  WebVPN

  OMITTED , OMIT encrypted privilege 15 password username

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  crashinfo console disable

  Cryptochecksum:3c8669ae6960ca4cc206db58ffbf3c21

  : end

  It is probably the string:

  Des-sha1 encryption SSL

  This weak encryption algorithm is not compatible with most modern browsers and the current Java releases that depend on ASSISTANT Deputy Ministers. Try adding encryption, for example:

  SSL encryption des-sha1 sha1-aes256

  Make sure that you first activation 3DES / AES ('see the version' or 'show the activation key' will confirm the feature license is active).

• Cannot access subnet when VPN would be

  When I vpn in our network, it gives me an ip address in the range: 192.168.200.1 - 192.168.200.50.

  The following access works when vpn would be: 192.168.200.x-> 10.2.28.x

  Made following access does not work when the vpn would be: 192.168.200.x-> 192.168.50.x

  Can you get it someone please let me know what I have in the PIX config to make it work?

  Thank you

  Thomas

  1. Add 192.168.50.0 to your acl of split tunnel

  remotevpnbhc_splitTunnelAcl 192.168.50.0 ip access list allow 255.255.252.0 all

  2. Add the traffic between the client vpn and 192.168.50.0 ACL that is used by NAT 0

  vpn_insideacl ip 192.16.50.0 access list allow 255.255.252.0 192.168.200.0 255.255.255.0

• ASDM 6.4; ASA 5510 version 8.4 (1) - cannot access ASDM

  Hello Experts,

  I want access to ASDM since my PC of management. I can ping to MANAGEMENT PC as well as do SSH connection but I can't go ASDM browser.

  Please guide me.

  Here are the usful details:

  ASDM - setup.jpg

  

  Running configuration

  See the ciscoasa # running
  : Saved
  :
  ASA Version 8.4 (1)
  !
  ciscoasa hostname
  activate 9jNfZuG3TC5tCVH0 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif inside
  security-level 90
  IP 192.168.1.1 255.255.255.0
  !
  interface Ethernet0/1
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  passive FTP mode
  pager lines 24
  MTU 1500 inside
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 641.bin
  don't allow no asdm history
  ARP timeout 14400
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  Enable http server
  http 192.168.1.5 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Telnet timeout 5
  SSH 192.168.1.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  username admin privilege 15 encrypted password e1z89R3cZe9Kt6Ib
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:afe73d128f7510e1bf9463fd698fa7fb
  : end
   
   
  Successful PING Bothways
   
  ciscoasa (config) # ping 192.168.1.1

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 192.168.1.1, time-out is 2 seconds:

  !!!!!

  Success rate is 100 per cent (5/5), round-trip min/avg/max = 1/1/1 ms

  ciscoasa (config) # ping 192.168.1.5

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 192.168.1.5, time-out is 2 seconds:

  !!!!!

  Success rate is 100 per cent (5/5), round-trip min/avg/max = 1/1/1 ms

  output ciscoasa (config) #.

  Thank you :-)

  Please let us know the output of:

  view worm | I have 3DES

  Show ssl

  The bits of this production key would ensure that your license 3DES / AES is active and your ASA supports strong cryptographic algorithms (encryption).

• Cannot access Internet on VPN 3005 concentrator

  I installed a new concentrator 3005. I am able to connect using the Cisco VPN client. Everything seems to work except the Internet. I am able to access everything in the local network, including local intranet Web pages. If I try to access Web pages on the outside, it does not. Any ideas?

  OK, so it seems there is a configuration or a problem with routing somewhere. Concentrator vpn routing table look like? Is there a default route set correctly? You can use ping to ping the default gateway?

  NAT is used? Is it possible the problem is that packages are not properly natted out to internet?

• ASA 5505 VPN established, cannot access inside the network

  Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.

  After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.

  Here is my config:

  ASA Version 8.2 (5)
  !
  hostname asa01
  domain kevinasa01.net
  activate 8Ry2YjIyt7RRXU24 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  switchport access vlan 5
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan5
  No nameif
  security-level 50
  IP 172.16.1.1 255.255.255.0
  !
  passive FTP mode
  DNS server-group DefaultDNS
  domain kevinasa01.net
  permit same-security-traffic intra-interface
  Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
  inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
  inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
  sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
  access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
  access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
  pager lines 24
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (outside) 1 192.168.254.0 255.255.255.0
  NAT (inside) 0 access-list sheep - in
  NAT (inside) 1 192.168.1.0 255.255.255.0
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Access-group outside_access_in in interface outside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.5 - 192.168.1.36 inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal Remote_Kevin group strategy
  attributes of Group Policy Remote_Kevin
  value of server DNS 192.168.1.12 192.168.1.13
  VPN - connections 3
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
  kevinasa01.NET value by default-field
  username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
  username kevin attributes
  VPN-group-policy Remote_Kevin
  type tunnel-group Remote_Kevin remote access
  attributes global-tunnel-group Remote_Kevin
  address-pool
  Group Policy - by default-Remote_Kevin
  IPSec-attributes tunnel-group Remote_Kevin
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the icmp error
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
  : end

  Thank you

  Hello

  I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.

  I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.

  The acl must be:

  sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0

  For nat (inside), you have 2 lines:

  NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
  NAT (inside) 1 0.0.0.0 0.0.0.0

  Why are you doing this nat (outside)?

  NAT (outside) 1 192.168.254.0 255.255.255.0

  Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)

  Thank you.

  PS: Please do not forget to rate and score as good response if this solves your problem.

• Why my VPN clients cannot access network drives and resources?

  I have a cisco asa 5505 configured to be a VPN gateway. I can dial using the anyconnect VPN client. The remote user is assigned an IP address to my specifications. However... The remote user cannot access network such as disks in network resources or the fax server. I've done everything I can to set the right settings NAT and ACLs, but in vain. I write my config... If someone can track down the problem. It would be appreciated!

  : Saved

  :

  ASA Version 8.2 (5)

  !

  ciscoasa hostname

  Cisco domain name

  activate the password xxxxxxxxxxxxx

  passwd xxxxxxxxxxxxxxxxx

  names of

  name 68.191.xxx.xxx outdoors

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.201.200 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address outside 255.255.255.0

  !

  passive FTP mode

  DNS domain-lookup outside

  DNS lookup field inside

  DNS server-group DefaultDNS

  192.168.201.1 server name

  Cisco domain name

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  object-group network obj - 192.168.201.0

  FREE access-list extended ip 192.168.201.0 NAT allow 255.255.255.0 192.168.201.0 255.255.255.0

  NAT-FREE 192.168.202.0 permits all ip extended access list 255.255.255.0

  FREE access-list extended ip 192.168.202.0 NAT allow 255.255.255.0 any

  Extended access list-NAT-FREE enabled a whole icmp

  allow any scope to an entire ip access list

  allow any scope to the object-group TCPUDP an entire access list

  allow any scope to an entire icmp access list

  inside_access_in of access allowed any ip an extended list

  inside_access_in list extended access allow TCPUDP of object-group a

  inside_access_in list extended access permit icmp any one

  outside_access_in of access allowed any ip an extended list

  outside_access_in list extended access allow TCPUDP of object-group a

  outside_access_in list extended access permit icmp any one

  Standard access list DefaultRAGroup_splitTunnelAcl allow 192.168.201.0 255.255.255.0

  access extensive list ip 192.168.202.0 inside_nat0_outbound allow 255.255.255.0 192.168.201.0 255.255.255.0

  inside_nat0_outbound list extended access permit icmp any one

  inside_nat0_outbound_1 of access allowed any ip an extended list

  pager lines 24

  Enable logging

  asdm of logging of information

  Outside 1500 MTU

  Within 1500 MTU

  mask 192.168.202.1 - 192.168.202.50 255.255.255.0 IP local pool KunduVPN

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  Global 1 interface (outside)

  NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access

  NAT (inside) 1 192.168.201.0 255.255.255.0

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route inside 0.0.0.0 0.0.0.0 192.168.201.1 1

  Route inside 0.0.0.0 255.255.255.255 outdoor 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.201.0 255.255.255.0 inside

  http 0.0.0.0 0.0.0.0 outdoors

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

  Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = ciscoasa

  Keypairs xxx

  Proxy-loc-transmitter

  Configure CRL

  XXXXXXXXXXXXXXXXXXXXXXXX

  quit smoking

  crypto ISAKMP allow outside

  crypto ISAKMP allow inside

  crypto ISAKMP policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  allow inside

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

  enable SVC

  tunnel-group-list activate

  internal DefaultRAGroup group strategy

  attributes of Group Policy DefaultRAGroup

  value of 192.168.201.1 DNS server

  VPN-tunnel-Protocol svc webvpn

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl

  Cisco by default field value

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  WebVPN

  SVC request enable

  internal KunduVPN group strategy

  attributes of Group Policy KunduVPN

  WINS server no

  value of 192.168.201.1 DNS server

  VPN-tunnel-Protocol svc webvpn

  Cisco by default field value

  username xxxx

  username xxxxx

  VPN-group-policy DfltGrpPolicy

  attributes global-tunnel-group DefaultRAGroup

  address VPNIP pool

  Group Policy - by default-DefaultRAGroup

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared key *.

  tunnel-group DefaultRAGroup ppp-attributes

  ms-chap-v2 authentication

  type tunnel-group KunduVPN remote access

  attributes global-tunnel-group KunduVPN

  address (inside) VPNIP pool

  address pool KunduVPN

  authentication-server-group (inside) LOCAL

  Group Policy - by default-KunduVPN

  tunnel-group KunduVPN webvpn-attributes

  enable KunduVPN group-alias

  allow group-url https://68.191.xxx.xxx/KunduVPN

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:c0e4540d4a07f2c544f0eddb653627cc

  : end

  don't allow no asdm history

  Hello

  What is the IP address of the hosts/servers LAN Gateway?

  If this is not the ASA 'inside' interface IP address then I assume that the problem with VPN is simply routing.

  For example, if your hosts/servers LAN wireless LAN gateway router then the following would happen to your Clients VPN connections.

  • Forms of customers login VPN users through configuring wireless routers static PAT (Port Forward) to interface "inside" ASA
  • Client VPN sends traffic through the VPN to ASA and again the host of the server or LAN.
  • Host/server LAN sees the connection from a network other than the LAN (192.168.202.0/24) and therefore to forward traffic to the default gateway that would likely be the wireless router.
  • Wireless router has no route to the network 192.168.202.0/24 (VPN Pool) and therefore uses its default route to the external network to forward traffic.
  • Client VPN host never received the traffic back as transmitted sound on the external network and abandoned by the ISP

  So if the above assumption is correct, then you would at least need a configuration of the road on the wireless router that tells the device to transfer traffic to the network 192.168.202.0/24 to the 192.168.201.200 gateway IP address (which is the SAA)

  I would like to know if the installation is as described above.

  -Jouni

• Cannot access the AIP SSM via ASDM

  CISCO recommendations below:

  Cannot access the AIP SSM via ASDM

  Problem:

  This error message appears on the GUI.

  Error connecting to sensor. Error Loading Sensor error

  Solution:

  Make sure that the IPS SSM management interface is up/down and check his IP address configured, default gateway and the subnet mask. It is the interface to access the software from Cisco Adaptive Security Device Manager (ASDM) on the local computer. Try to ping the address of management of IPS SSM IP interface on the local computer that you want to access the ASDM. If it is impossible to do a ping check the ACLs on the sensor

  ----------------------------------------------------------------------------------------------------------------------------------------------

  I've tried everything recommended above. I can ping the host ASDM the FW and the SSM-10 module. Well, I ping the host machine and the SSM of the ASDM. I opened as wide as possible ACL. I changed the IP addresses and masks several times. The management of the ASA port and the SSM and the PC are on the same subnet.

  A trace of package from the PC to the SSM shows that it is blocked by an ACL rule, and yet I opened wide.   I've seen this kind of problem before and it was solved by applying the double static NAT, but I don't know how to do that if all the IP addresses are on the same subnet.

  Tried everything, need help from high level.

  The IDM software that comes with ASDM does not support java 1.7. The portion of the ASDM ASA supports 1.7 but launch the IPS cmdlet works only with 1.6. The TAC enginner suggested that I use the IME (IPS Manager Express) which is available for free on the Cisco's (http://www.cisco.com/en/US/products/ps9610/tsd_products_support_general_information.html) Web site.

  I've been playing with it today, and so far it seems to work pretty well.

• The VPN Clients cannot access any internal address

  Without a doubt need help from an expert on this one...

  Attempting to define a client access on an ASA 5520 VPN that was used only as a

  Firewall so far. The ASA has been recently updated to Version 7.2 (4).

  Problem: Once connected, VPN client cannot access anything whatsoever. Client VPN cannot

  ping any address on internal networks, or even the inside interface of the ASA.

  (I hope) Relevant details:

  (1) the tunnel seems to be upward. Customers are the authenticated by the SAA and

  are able to connect.

  (2) by many other related posts, I ran a ' sh crypto ipsec her "to see the output: it

  appears that the packets are décapsulés and decrypted, but NOT encapsulated or

  encrypted (see the output of "sh crypto ipsec his ' home).

  (3) by the other related posts, we've added commands associated with inversion of NAT (crypto

  ISAKMP nat-traversal 20

  crypto ISAKMP ipsec-over-port tcp 10000). These were in fact absent from our

  Configuration.

  (4) we tried encapsulation TCP and UDP encapsulation with experimental client

  profiles: same result in both cases.

  (5) if I (attempt) ping to an internal IP address of the connected customer, the

  real-time log entries ASA show the installation and dismantling of the ICMP requests to the

  the inner target customer.

  (6) the capture of packets to the internal address (one that we try to do a ping of the)

  VPN client) shows that the ICMP request has been received and answered. (See attachment

  shooting).

  (7) our goal is to create about 10 VPN client of different profiles, each with

  different combinations of access to the internal VLAN or DMZ VLAN. We do not have

  preferences for the type of encryption or method, as long as it is safe and it works: that

  said, do not hesitate to recommend a different approach altogether.

  We have tried everything we can think of, so any help or advice would be greatly

  Sanitized the ASA configuration is also attached.

  appreciated!

  Thank you!

  It should be the last step :)

  on 6509

  IP route 172.16.100.0 255.255.255.0 172.16.20.2

  and ASA

  no road inside 172.16.40.0 255.255.255.0 172.16.20.2

• RV120W - cannot access static IP via VPN devices

  Hello

  I have a RV120W used to provide VPN access to several industrial devices. Some of these devices are assigned via DHCP from the router IP address. Can not do DHCP, so there a self-determined static IP.

  The VPN works well for all devices that are affected intellectual property. However, it does allow me to connect to the device that has a static IP address. I can connect to it very well when I'm on the LAN or WLAN, but it cannot ping via the VPN.

  Help!

  Thank you-

  Bailey

  Hi Bailey, it seems that the static device has no default gateway are entrusted to him.

  -Tom
  Please mark replied messages useful

• VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK

  I tried to set up a simple customer vpn using this document

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a00801e71c0.shtml

  VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK BEHIND "RA"...

  6.3 (5) PIX version

  interface ethernet0 car

  Auto interface ethernet1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the encrypted password of VmHKIhnF4Gs5AWk3

  VmHKIhnF4Gs5AWk3 encrypted passwd

  hostname VOIPLABPIX

  domain voicelab.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0

  access-list 101 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0

  access-list 102 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0

  access-list 102 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside 208.x.x.11 255.255.255.0

  IP address inside 172.10.2.2 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool voicelabpool 172.10.3.100 - 172.10.3.254

  history of PDM activate

  ARP timeout 14400

  NAT (inside) - 0 102 access list

  Route outside 0.0.0.0 0.0.0.0 208.x.x.11 1

  Route inside 172.10.1.0 255.255.255.0 172.10.2.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 172.0.0.0 255.0.0.0 inside

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp-aes-256 trmset1, esp-sha-hmac

  Crypto-map dynamic map2 10 set transform-set trmset1

  map map1 10 ipsec-isakmp crypto dynamic map2

  client authentication card crypto LOCAL map1

  map1 outside crypto map interface

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 encryption aes-256

  ISAKMP policy 10 sha hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup address voicelabpool pool cuclab

  vpngroup dns 204.x.x.10 Server cuclab

  vpngroup cuclab by default-field voicelab.com

  vpngroup split tunnel 101 cuclab

  vpngroup idle 1800 cuclab-time

  vpngroup password cuclab *.

  Telnet timeout 5

  SSH 208.x.x.11 255.255.255.255 outside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 172.10.1.2 255.255.255.255 inside

  SSH timeout 60

  Console timeout 0

  username labadmin jNEF0yoDIDCsaoVQ encrypted password privilege 2

  Terminal width 80

  Cryptochecksum:b03a349e1ac9e6022432523bbb54504b

  : end

  Try to turn on NAT - T

  PIX (config) #isakmp nat-traversal 20

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml#Solution1

  HTH

• RVL200 SSL VPN: cannot access a remote LAN with iPad2

  RVL200 firmware 1.1.12.1

  iPad2 cannot access any device on the Remote LAN despite the closed padlock icon.

  Is there another App needed? Or how to debug SSL VPN?

  Emmanuel,

  Were you able to access the LAN devices? Also, have you connected using a Mac or a PC successfully to verify that the devices are available? Sometimes antivirus and firewall software can block access to devices from a remote IP address.

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• ASA 5505 VPN cannot access inside the host

  I have access remote VPN configuration on an ASA 5505, but cannot access the host or the AAS when I connect through the VPN. I can connect with the Cisco VPN client and the VPN is on on the SAA and it shows that I am connected. I have the correct Ip address, but I can't ping or you connect to one of the internal addresses. I can't find what I'm missing. I have the VPN without going through the ACL interface. Because I can connect but not going anywhere I'm sure I missed something.

  framework for configuration below

  interface Vlan1

  nameif inside

  security-level 100

  10.1.1.1 IP address 255.255.255.0

  IP local pool xxxx 10.1.1.50 - 10.1.1.55 mask 255.255.255.0

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map 20 set pfs

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  PFS set 40 crypto dynamic-map outside_dyn_map

  Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA

  Crypto-map dynamic inside_dyn_map 20 set pfs

  Crypto-map dynamic inside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  map inside_map 65535-isakmp ipsec crypto dynamic inside_dyn_map

  inside crypto map inside_map interface

  crypto ISAKMP allow inside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  global service-policy global_policy

  XXXXXXX strategy of Group internal

  attributes of the strategy group xxxxxxx

  banner value xxxxx Site Recovery

  WINS server no

  24.xxx.xxx.xx value of DNS server

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  by default no

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout no

  disable the IP-phone-bypass

  disable the leap-bypass

  disable the NEM

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  the address value xxxxxx pools

  enable Smartcard-Removal-disconnect

  the firewall client no

  WebVPN

  url-entry functions

  Free VPN of CNA no

  No vpn-addr-assign aaa

  No dhcp vpn-addr-assign

  tunnel-group xxxx type ipsec-ra

  tunnel-group xxxx general attributes

  xxxx address pool

  Group Policy - by default-xxxx

  blountdr group of tunnel ipsec-attributes

  pre-shared-key *.

  Missing nat exemption for vpn clients. Add the following and you should be good to go.

  inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255.0

  NAT (inside) 0-list of access inside_nat0_outbound

• PIX501 customer VPN - cannot access inside the network with VPN Session

  What follows is based on the config on the attached link:

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a008009442e.shtml

  PIX Ver 6.2 (3) - VPN Client 3.3.6(A) - Windows XP Client PC

  We can establish the VPN to the PIX501 session, but we cannot access the network private behind the pix.

  Here is the config - I can't determine why it does not work, we are desperate to get there as soon as POSSIBLE!

  We have the same problem with the customer 4.0.3(c)

  Thanks in advance for any help!

  =======================================

  AKCPIX00 # sh run

  : Saved

  :

  6.2 (3) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname AKCPIX00

  domain.com domain name

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  fixup protocol sip udp 5060

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  external IP address #. #. #. # 255.255.240.0

  IP address inside 192.168.1.5 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool akcpool 10.0.0.1 - 10.0.0.10

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 #. #. #. # 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup address akcpool pool akcgroup

  vpngroup dns 192.168.1.10 Server akcgroup

  vpngroup akcgroup by default-domain domain.com

  vpngroup split tunnel 101 akcgroup

  vpngroup idle 1800 akcgroup-time

  vpngroup password akcgroup *.

  vpngroup idle 1800 akc-time

  Telnet timeout 5

  SSH #. #. #. # 255.255.255.255 outside

  SSH timeout 15

  dhcpd address 192.168.1.100 - 192.168.1.130 inside

  dhcpd dns 192.168.1.10

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXX

  : end

  AKCPIX00 #.

  Config looks good - just as domestic mine to my local network. The only thing I can think is that you may have entered commands in the wrong order - which means, you could have isakmp or encryption before the config map was complete. Write memory, then reloading the pix is a way to reset everything. If you do not want downtime:

  mymap outside crypto map interface

  ISAKMP allows outside

  Enter these two commands should be enough to reset the ipsec and isakmp.