Cannot access BIOS after closing down and also can not use change PC settings either.

Similar Questions

• I'm unable to connect to the internet and I also can not use the WinXP system restore.

  No internet connection and I also can not use the WinXP system restore because it gives me an error at the 'end' which said: it cannot be restored to an earlier date.  I run AntiMalware bytes and StopZilla and erased all that they found.  Now I can't even connect to the internet.  When I go to the command prompt, it gives me an error contact the Support of MS that I know means I have a virus or a trojan that I should just get a time out?  My other PC on the same network is fine and connected.  The NETWORK card is fine, just does not know how to get rid of what it is, I have and to top it all impossible to connect to the internet to try all of the tools that can help.  Someone at - it ideas?

  The error you get at the end of the restoration of the system is typical of some anti-virus programs (Norton, especially) that interfere with the restoration of the system.  Try to start your computer in Mode safe (on several occasions, key to tap F8 while your computer starts) and run safe mode system restore.

  Additional information is necessary to treat your network problem.  Try to bring up a command prompt (start-> Run-> "cmd") or if it does not, try (start-> Run-> "command.com") and enter the command:
  ipconfig/all
  and after the info that appears in the State resulting.

  Also, check the logs of your system related errors (start-> Run-> "eventvwr.msc") and click on 'System' in the left column.

  HTH,
  JW

• Cannot access bios after installing the video card

  I have a PC HP 800 G1 tour.  When I install an EVA GT 520 external video card I can access is no longer the first screen to get the bios unless I get out the video card.  I want to change the bios to use only the external card, or at least to see the initial splash screen, but cannot access it.  It is running windows 8.1.  I updated the bios to the lasest version and still the same.

  Hello:

  You may need to change some BIOS settings - even if you add an external video card...

  http://support.HP.com/us-en/document/c03653200

• Cannot access BIOS after own Win 7 installed on the new HD

  The machine is HP Elite E9240F. Here's what I did.

  1 replace the plant HD with faster player - went well

  2. clean install Win 7 on new drive - activate - went well

  3 reinstall the disc supplied with the box in the first place & format - went well.

  Now everything starts fine, and loads of Windows. NO problem BUT I cannot access the BIOS more. Not that I need at this time, but I would like to know that where I did it, I could.

  Repeated F1 or F11 at startup pressure will produce the black screen for the Windows Boot Manager.

  I removed the CMOS battery and retried - same results. I can access the blue screen when I select the boot sequence by pressing ESC but never can I go back in the system BIOS.

  Thoughts?

  All these systems are a bit different but F10 to enter the bios to me.  If it is your PC then F10 to enter the bios: http://support.hp.com/us-en/document/c01925486

• Satellite C660-125 - cannot access BIOS after upgrade to Windows 10

  Hello, I just upgraded to 10 Windows Home of Windows 7 and now HWSETUP. EXE is not running and when restart the laptop I can't enter the BIOS with F2 or F12. Can someone companion please? Kind regards

  You must install the driver from Toshiba for Windows 10 system.
  However the C660 does not seem to be in the supported list, you may need to go into BIOS instead.

  Hold SHIFT key during shutdown to shut down Windows hybrid suspension mode. Keep now SHIFT until the power goes out.
  The BIOS F2 message appears only if the laptop is a cold start.

• Pavilion g6t-2300 CTO select: seeing power HP Pavilion is still on even after closing down and the battery won't charge no - 10 Windows

  My HP Pavilion power LED is still even after closing. I disabled option quick start, but the problem was not fixed. Another problem is the battery will not charge if it is showing connected. My OS is wondows 10. Please help me. Thank you.

  Hello

  Please try the following fix:

  https://www.CNET.com/forums/discussions/help-my-PC-with-Windows-10-wont-shut-down-properly/

  Kind regards.

• My site is down and I can not connect.

  Help, please!

  My site was working.

  But now he is not.

  www.morganevansmedia.com

  I can not connect to BC either.

  Hello

  Your site does not point to Business catalyst, so you cannot access it by using your custom domain name. Unless you do this, copy the url for your system to connect to your site administration panel.

  Login administration

  You can use the following method to point your domain to BC

  http://docs.BusinessCatalyst.com/user-manual#! / site-settings/site-areas/change-the-d n-name-of-your-website

  Add a domain name to your site by using an external DNS service

  Let me know if you have any question.

• I have an officejet 6600 and I can not use the copy function. any suggestions?

  I just bought an officejet 6600 and I tried to use the copy function.  Is it possible to copy a few items @ a time on the top

  HI yankee59,

  What happens if you go to your printer and select copy on the front panel? Do you get the options to copy as many copies ect...?

• After 4.4.2 update can not use WiFi & Bluetooth togeth

  After that I updated to KitKat 4.4.2 cannot use WiFi and Bluetooth at the same time. Must turn off Bluetooth to use WiFi.can you help with this problem. I have the Motorola droid RAZR maxx hd

  Double wire closure. Thanks for posting here.

  Mark

  Forums Manager

• VulcanControl.dll is missing. I deleted the apps, reinstalled, used the removal tools, and still can not use the extension manager for Dreamweaver, etc...

  If it can't be fixed Im moving to another company.as software it takes much too long and I've tried everything on the forums.

  Hi davidp67009702,

  Please refer to this thread vulcancontrol.dll missing, could be of great help to solve this problem.

  Kind regards

  Nicos

• I can't use my new computer STOP because IT WILL NOT be updated! AND I can't use my old software? Wish you shit salesman told me that huge a pos is 64 _ is, I can't WAIT NOW MS LUI AND YOU

  THIS IS NUTS!  Just bought this computer and two days its been "updated" ALL THE TIME, more than 200 + "updates" so far, rebooting over and over again, this 64-bit running MUCH slower than the old xp AND I CAN NOT USE ANY OF MY OLD SOFTWARE, BAD BAD BAD I now see that I made a HUGE MISTAKE.  I am the most unfortunate customer with this pos!

  Take it to where you bought it. ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Cannot access BIOS when OS disk encrypted w / Bitlocker, starting on the USB key is not unlock disc

  Hello

  I enabled Bitlocker on my Acer Aspire 5315. The system partition is encrypted and the data partition. My motherboard doesn't have a TPM chip, so I opted for the unlock with a USB key.

  When I start the PC or wake them from their hibernation, the splashboot (with the logo of Acer) BIOS screen does not display the information below on how to access the BIOS (press F2) or the boot menu (F12). And therefore I can't access those as I used to.

  BitLocker does not account for the USB key, then asks for the password to unlock the HARD drive. Then Windows starts very well.

  However, restart (by a Windows or after you have entered the wrong password Bitlocker too many times), the BIOS splash screen is normal (with how access BIOS and boot menu), I can access BIOS by pressing F2 AND succesfully Bitlocker unlocks the HARD drive with the USB flash drive without having to ask for the password.

  So, my question is how Bitlocker unlock the HARD disk automatically via the USB when the PC starts?

  Thank you for reading.

  Note: I posted this question on http://social.technet.microsoft.com/Forums/en-US/w8itprosecurity/threads they suggested that I ask the Acer support.

  Thank you also get answers in the TechNet forums.  I'm sorry that you were unable to get a more complete answer it.

  We suggest that you uninstall BitLocker and decrypt the drive to determine if this restores your ability to access the BIOS.

• Satellite A500 will not start - cannot access BIOS

  Hello

  This morning, I got my satellite a500-1GH. I activated the option "quick start" in the bios and can not enter the bios since the screen jump the "f2" for the parameters and f12 for the boot menu and I can't get into the bios.

  I tried press f2, as soon as I turn on the computer but it dosent get into the bios menu.

  And also the custom of the bone rises, the stack of the screen in 'bbs-hard disk... boot. "and it stay like that until I shut down the computer.

  Please help me here...
  Thank you!

  Hello

  To me it seems strange that you can not enter the Bios. I just suggest you plug the keyboard external usb and try to enter the Bios (maybe, for some reasons allowing the quick start, the laptop keyboard doesn't work pressing f2). Then try to remove the hard drive and check.

  I've no idea what to say, maybe other users will also suggest something.

• Satellite L30-134 does not access BIOS after upgrade with SSD

  Hello

  I have a problem with my old Toshiba L30-134.

  When I try to replace the old with new SSD HARD drive, I can't start BIOS.
  But when I remove the DVD-ROM laptop and leave there only SSD, then BIOS can start and I see the drive detected. DVD - ROM has PATA/IDE interface.

  I also tried IDE adapter SATA (like this: [adapter | http://goo.gl/W3TpXt]) for replacement of the DVD-ROM with second SATA HDD and I had the same problem when the disk was present in the adapter.

  When the second HARD drive was not present in the adapter, BIOS began. And it's not just about BIOS.

  Computer is blocking on startup TOSHIBA logo screen during the hardware detection and there is also no error message.

  I can't change the settings on the device SATA IDE/AHCI mode. Is there a workaround with riders or a software solution?

  Thanks for help

  Hello

  > When the second HARD drive was not present in the adapter, BIOS has begun. And it's not just about BIOS.

  You replaced the STRANGE with a HARD drive?
  It won't work buddy. The s laptop computer's optical disc drive supports IDE controller. The HARD drive seems to support the SATA controller.

  The laptop does not power upward because the POST (power on self-test) cannot be passed correctly. During POST the laptop s material will be checked for a possible malfunction or compatibility issues. In your case, the hardware is NOT compatible and that you can't change that.

• cannot delete the folder I am one user have access to all the files and folders can remove any but one could take ownership of disk backup file

  Cannot delete the folder, I can move it, is presantly on my desk, I'm only user I have access to all the files and folders can remove everything, but this one, took possession of the file. file is made backup disk before I reloaded vista Explorer cause did not work right

  Try to open an administrator command prompt. Then cd to the desktop. Finally, run 'attrib-h - r s' and also ' attrib s h - r/s -*.» * ». Then right-click on the folder and check the button unblock. Similarly, with all the files in the folder, pledge. Never underestimate your own stupidity.