Cannot access the network ERR_NETWORK_ACCESS_DENIED

Similar Questions

• Cannot access the network drive or impossible to mount the network drive. Error "network path was not found.

  Original title: network path was not found

  HI, after the upgradation from windows xp sp2 to sp3 (next to the customer) I can't access the network drive or impossible to mount the network drive. ' ' It showa error "network path was not found.

  Hi gauravadavadkar,

  Thanks for posting your query in Microsoft Communities. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         What is the full error message?

  ·         Work on a domain?

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with networkand check if the problem persists.

  S tep 2: if the problem does not persist in safe mode with networking, perform a clean bootto see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the steps to configure Windows to use a Normal startup state section of the article to start the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Startand then click run.

  (b) type msconfigand click OK.
  The System Configuration utility dialog box appears.

  (c) click on the general tab, click Normal Startup - load all device drivers and services, and then click OK.

  (d) when you are prompted, click restart to restart the computer.

  Method 3: Follow the steps in the article.

  How to troubleshoot a network home in Windows XP

  In Windows network connection issues

  You can read this article for more information:

  Windows wireless and wired network connection problems

  I hope this helps. Let us know if you need more assistance.

  Thank you.

• Cannot access the network using WiFi hotspot

  I have a lenovo ideapad z570 running windows 7 ultimate, processor intel pentium cpu B950 @2.10 GHZ 2 GB ram and 64-bit operating system. My problem is that when I create a wifi hotspot via intel my wifi technology, I so can not access the network on my android phone or the playstation 3. There is a sign yellow triangle on the wireless icon and I have the cursor on it, she reads, access to the internet network, unidentified network no internet access. I tried to update all the drivers, I even reinstalled the operating system after a wipe, same result. I tried to use programs such as connectify but same result. Please help me

  Original title: network
  

  There is a sign yellow triangle on the wireless icon and I have the cursor on it, she reads, access to the internet network, unidentified network no internet access. I tried to update all the drivers, I even reinstalled the operating system after a wipe, same result. I tried to use programs such as connectify but same result. Please help me

  Hello

  You try to use the Add-hock network so that you can access ac in android are as good as play station unit
  Like you would have checked in the id network properties material and device id, it yellow list means problem with driver, please try to update the BIOS and the driver appropriate with the hardware ID, if possible to install from the laptop power management

  IdeaPad Z570.please press fn + f5 and check the layout state of WIFI is turned on, current state should off
  Download these drivers and install it, then try again
  http://download.Lenovo.com/userfiles/Driver/en/downloads%20and%20Drivers/Z570/Win7/IN1WLN90WW5.exe

  http://download.Lenovo.com/userfiles/Driver/en/downloads%20and%20Drivers/Z370Z470/IN8STW09WW5.exe
  http://download.Lenovo.com/userfiles/Driver/en/downloads%20and%20Drivers/Z570/Win7/IN1MEI08WW5.exe
  http://download.Lenovo.com/userfiles/Driver/en/downloads%20and%20Drivers/Z570/Win7/IN1CHP30WW5.exe

• Cannot access the network - Get unspecified error 0 x 80004005

  Hi all

  I have a strange problem that I hope someone can help me with.

  I have a PC Windows Vista Ultimate, newly installed, all the patches applied. Any other installed apps don't except MS Office.

  Not my problem, I have a NAS drive on my network and can be accessed by different machines on my network (IE. \\NAS)

  However for some reason any my Vista machine has ceased to recognize this. Now I can only connect via an IP address (IE. ( \\192.168.0.2).

  Whenever I have try type \\NAS he says "Windows cannot access \\NAS... etc etc" with a "unspecified error 0 error Code 80004005 x.

  He used to work, but now it does which is very weird. When I click on diagnose says that it cannot find \\NAS. However, as this network drive has a web front end, when I type its IP address there is no problem at all and I can access it, but not through windows Explorer! I use a TP-Link wireless adapter. I have a LAN connector normal that I disabled and enabled with no effect (although I have not physically connected them)

  I can navigate to Windwos Vista machine to it seems to work very well.

  Any ideas?

  Thanks in advance.

  Neal.

  If the regular way, you connect a reader could not be used and that you were forced to connect by ip, get error 80004005 would make sense, because it means that the rights or false refused/insufficient access permissions. Your network can have a parameter saying denied access by ip address, so either you might find this setting, or find a way to solve the original problem, making it impossible to connect as normal to you.

  I would check the firewalls, because your firewall or the firewall of the NAS could have been changed to not connect to the NAS or do not allow you to connect, respectively.

• Cannot access the network drive after trying to change the shared folder.

  I had a 80 GB drive connected to my E3000 for a few years and it worked without problem. I recently turned to a 250 GB Maxtor One Touch drive. When I plugged it, the router automatically creates a shared folder. I was able to connect to this folder without problem, but I wanted to share the whole score. When I made this adjustment and tried to save the settings, I temporarily lost access to the router. He gave me the standard page cannot be error message appears. When I got access changes seem to be made. When I try to access the drive of my laptop I get this error message, "the mapped network drive could be created", "the name specified network is no longer available". I rebooted and power rolled my router as well reconnected the drive.

  I think that since you have replaced your hard drive, old settings are configured may still on the hard drive of old. You can change the users and group so that it syncs with the new hard drive or start from scratch (reformat the hard drive).

• Cannot access the network after you have installed the Windows updates

  original title: Windows update and Acer Aspire M3201

  Hi, I have a problem with my Acer Aspire M3201, which has Windows Vista on it. The system has installed the Windows Update automatically, so I can't access the internet and home network more. So I restored the previous update windows, then I can get into the internet again. A week later the update windows again but this time somehow corrupted previous restoration, I cannot restore and can not enter in the internet. I bought Windows 7 to upgrade my Windows Vista computer. The upgrade went OK game, but it was also installed the updateautomatically, and I cannot yet access the internet web browser of screws, but the command, I can ping any web site as www.cisco.com. Please help me. Thank you.

  If you updated that could trigger it, you can do is to uninstall and avoid installing it by hiding the update in Windows Update.

  Click Start, type: see installed updates
  Press enter on your keyboard
  Look for the update in question, no it click on, then click on uninstall.

  Restart your computer

  Open Windows Update, select the update, right-click and click Hide

  See also: Troubleshoot network Windows 7 http://clkon.us/bJtkA0

• Cannot access the network without password drives?

  I had a failure of hard drive on my laptop and I can't access my network of resources to work after installing the new drive.  A dialog box opens for a username and password when I try to map a network drive.  No other computer in fact.  Vista is the problem, but what is the solution?

  You must create an identical user account and password on your Vista machine that corresponds to the remote computer. The error you get indicates that you did not do this. MS - MVP - Elephant Boy computers - don't panic!

• Cannot access the network settings in the browser

  
  

  Someone else has replied to a similar post of mine with these instructions and it worked, so I thought that I have to pay it before... hope it works for you!

  Try the steps to reset the printer below. Note that each setting (network configuration, fax settings/information etc.) on your printer will probably be erased.

  1. turn off the printer

  2. on the keypad, press in and hold the # and 6 at the same time. While now the two buttons under the printer.

• Virtual machines are not able to access the network after you have moved the host

  We moved our 4 ESX host to a different physical switch and now our VMs cannot access the network.

  I can access the host via client vsphere.  Our host has 2 network cards.  They are both members of the vSwitch0.  I have 1 VM network defined, and they are both members of it.  The network adapters, vmnic0 and vmnic1 are also part of my VMkernel which I do not know that I need because I have 1 ESX Server and do not use iscsi or NFS.

  the two cards are also part of my service console.

  According to my host "configuration / display: vitual switch, it looks like all my virtual machines are defined to use the vswitch."

  the two physical network adapters is connected to the same switch.  I did not go to any configuration on the switch.

  

  The steers would be appreciated.

  Thank you

  Paul

  

  Welcome to the community,

  It sounds as if the physical switch ports are not configured correctly. Please check that port security is disabled on the switch (switchport mode access) ports and spanning tree portfast is (if any).

  André

• Cannot start the network connection: invalid access to memory location

  Hi team,

  Windows 2003 SP2 cannot start the network connection. Error connections network service terminated with the following error: invalid access to memory location.  Can you help me on this issue?

  Thank you

  Sangaré

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Windows Server 2003 Forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads

• Cannot access the internet on a network Windows XP when Windows 7 goes to sleep

  Original title: Windows 7 Windows XP network problem.

  I replaced a Windows XP computer on my node 4 (2 PC, printer 2) cable network with a Windows 7 computer.  When the Windows 7 computer in mode 'sleep' the other (XP) computer cannot access the internet.  A message appears that there are 2 computers with the same IP address.  If I wake the computer 7 fine.  That is what it is?  I agree not all files between the computers.

  Hello

  It is usually the case when, for example, a router is off, but one or more of the devices connected to the router are left on.

  The devices to retain the ip address assigned to them, but when the router starts up again it has no knowledge of this. If when you start one of the other devices, the router can assign an ip address already in use. Concrete example that I reproduced with my router and the PC...

  • Start the router, then boot PC1 and PC2 - the router (192.168.1.1) will allocate for PC1 192.168.1.2 and 192.168.1.3 to PC2
  • Turn off the router, then turn off PC2, restart and shut off again
  • Put the PC1 to sleep
  • Start the router and PC2, the router does not PC1 and allocate 192.168.1.2 to PC2
  • PC1 to wake up and there still 192.168.1.2 who now is a confrontation with PC2

  Other ways to reproduce this situation may also be possible.

  All devices on your network must have a unique ip address, where the warning message.

  If you get this situation once again, the solution is to turn off all devices, including the router, then restart the router, then restart all devices connected to the router.

  To avoid this, you may be able to put ip Reservations for your router address which will ensure that all devices connected to the router always get the same ip address (unique). If you are unsure how to proceed, we will need your router brand and model to help.

  Tricky

• VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK

  I tried to set up a simple customer vpn using this document

  http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a00801e71c0.shtml

  VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK BEHIND "RA"...

  6.3 (5) PIX version

  interface ethernet0 car

  Auto interface ethernet1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the encrypted password of VmHKIhnF4Gs5AWk3

  VmHKIhnF4Gs5AWk3 encrypted passwd

  hostname VOIPLABPIX

  domain voicelab.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0

  access-list 101 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0

  access-list 102 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0

  access-list 102 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside 208.x.x.11 255.255.255.0

  IP address inside 172.10.2.2 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool voicelabpool 172.10.3.100 - 172.10.3.254

  history of PDM activate

  ARP timeout 14400

  NAT (inside) - 0 102 access list

  Route outside 0.0.0.0 0.0.0.0 208.x.x.11 1

  Route inside 172.10.1.0 255.255.255.0 172.10.2.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 172.0.0.0 255.0.0.0 inside

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp-aes-256 trmset1, esp-sha-hmac

  Crypto-map dynamic map2 10 set transform-set trmset1

  map map1 10 ipsec-isakmp crypto dynamic map2

  client authentication card crypto LOCAL map1

  map1 outside crypto map interface

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 encryption aes-256

  ISAKMP policy 10 sha hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup address voicelabpool pool cuclab

  vpngroup dns 204.x.x.10 Server cuclab

  vpngroup cuclab by default-field voicelab.com

  vpngroup split tunnel 101 cuclab

  vpngroup idle 1800 cuclab-time

  vpngroup password cuclab *.

  Telnet timeout 5

  SSH 208.x.x.11 255.255.255.255 outside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 172.10.1.2 255.255.255.255 inside

  SSH timeout 60

  Console timeout 0

  username labadmin jNEF0yoDIDCsaoVQ encrypted password privilege 2

  Terminal width 80

  Cryptochecksum:b03a349e1ac9e6022432523bbb54504b

  : end

  Try to turn on NAT - T

  PIX (config) #isakmp nat-traversal 20

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml#Solution1

  HTH

• Cannot access the internet with bridged network - Windows 7 64 bit host, XPSP3 comments

  I use VMPlayer v3.0.1 build-227600 on a PC under Windows 7 64-bit. My guest operating system is Windows XP Professional w/SP3.

  I read all the messages on the use of NAT for the guest operating system can access the internet. But when I do that my guest is unable to access my Oracle server on my network. If I use Bridged my guest can access my Oracle server, but it cannot access the internet! How can I fix it? Shouldn't VMPlayer allow the guest OS to access the network and the internet? I need these two features.

  Any help would be appreciated.

  the simplest solution would be to add a second NIC to your comments, so that you can have bridged and NAT at the same time

  ___________________________________

  VMX-settings- Workstation FAQ -[MOA-liveCD | http://sanbarrow.com/moa241.html]- VM-infirmary

• Just upgraded to El Capitan and cannot access the calendar. It opens with a "Shift schedules to the server" message Can only Force Quit

  Just upgraded to El Capitan and cannot access the calendar. It opens with a message 'Moving calendars to the server.

  I cannot access all features and can be closed only by using force quit.

  Please stop calendar and also the application of reminders, runs. Force quit if necessary.

  Back up all data.

  If you synchronize some of your calendars, or reminders with iCloud, then in the iCloud preferences window, uncheck that marked calendars and reminders. You will be prompted to confirm that you want to remove your iCloud calendars and reminders of the computer. They will always be in iCloud. Re-check the boxes.

  If you synchronize agendas or reminders with another network such as Google service, please open the preferences panel Internet accounts. Make a note of the settings for calendar accounts, then delete and recreate.

  Launch schedule and see if there is an improvement.

• HP 15 laptop: laptop computer is connected to the wi - fi connection, but cannot access the internet

  Hello

  My problem is my WiFi says its connected but I can't browse or access the internet.it just tells me "unable to connect to internet computer is not connected to the internet", but my wifi says 'connected'.i tried to go to the cmd prompt and typed in "netsh int ip reset resetlog.txt c:\" goal it shows me "reset failed.access is denied .he don't s no user specified settings to be reset to zero." please "» What can I do?

  Thanks in advance.

  Hello @jerome256,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums, I would like to draw your attention to the HP Forums Guide first time here? Learn how to publish and more.

  I understand that you are having a problem with your WiFi and wanted to help you!

  You are trying to access WiFi through router?  If you are connected to your wireless network, but cannot access the internet, then the problem may be with the router.  Check that the router is connected to the internet.  If you have more than one router, then you can ensure that you are connected to the correct router.  You can also try unplugging the router for about 30 seconds, and then reconnecting it.  Please consult the following document, as it can help solve the problem for you:

  HP PC - Troubleshooting wireless network and Internet (Windows 10)

  Please let me know if this information has been helpful by clicking the thumbs up below.

  Have a great day!