Cannot access the WRT320N cascading to the IP 192.168.1.2

Similar Questions

• Why can't I access the modem 192.168.1.1 when connected to the wireless router?

  I'm unable to access my DSL Modem 6100 Westell using 192.168.1.1 when connected to the Netgear WNDR3400 wireless router. I can access it, however, when I connect directly to the ethernet port on the computer without going through the router. I've set up according to the instructions. Is it possible to correct the problem?

  This isn't a problem.  This is the standard behavior.  You are connected to the side LAN of the router that is isolated from the side WAN (uplink).  This is the mode of operation of routers.

• Impossible to access the gateway 192.168.1.1 username and password is incorrect

  When I want to access 192.168.1.1the user name and password that worked before now don't work anymore! Why?

  If someone forgets his password it should do? How can I reset my login and my password?

  I really have to change the configuration of my router. My router model is WAG120N

  Thank you

  You can try to connect to the router configuration page using i.e. password default "admin", if it does not, then you can use "admin" as the user name and password and then check... If this still does not work then you need to reset your router.

  To reset your router press and hold the reset button on the back of your router for 30 sec then unplug the power supply and reconnect it back... But it will restore your default router.

• under vista and it cannot open the Web 192.168.1.1 for linksys router

  I have a Linksys wrt54gl router wireless and I hard wire plugged into my computer so I connected to the internet broadband router. Connections to work because the flashing lights on the front of the router blink correctly.  So I open internet explore and type 192.168.1.1 in the hope that I get the page for the router setting, but instead, I get a message that explore cannot detect the Web site. Wrong address. I get a similar error with Firefox.  The computer was working fine connected directly to the internet bandwidth so sure the internet works. The IP address is set to automatic detection. Someone at - it ideas?

  Hello

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• can not access the router (192.168.1.1) of the browser firefox web

  When I try to access my RV042G Gigabit Dual WAN VPN router from firefox or chrome I get an error message

  > An error occurred during a connection to 192.168.1.1. SSL has received a low ephemeral Diffie-Hellman key in the handshake message exchange the server key. (Error code: ssl_error_weak_server_ephemeral_dh_key)

  I had a similar problem with the storage attached network (Synology Diskstation) unit but I was able to create a certificate that meets the "modern standards" and the problem was solved.

  I need to create a new certificate for the web server on the router RV042G?  How?

  FYI - running firmware 4.2.3.06

  Thank you

  Lee

  Hello Lawrence,.

  Thank you for using the small community of Support Business!

  It is a known problem that affects a number of products for small business. There is another post which lies here who has some solutions you can try.

  If you have any other questions, please post them here and I'll do my best to help you!

  Best,

  Taylor

• cannot access the internet after upgrading to firefox 30.0 on windows 7

  After the upgrade to firefox 30.0 on windows 7, cannot access the internet. FF 30.0 works OK under Vista

  Sometimes it's because of your security software thinking that the upgrade may not be legitimate. You can consult this article: problems connecting to websites after Firefox update.

• Just upgraded to El Capitan and cannot access the calendar. It opens with a "Shift schedules to the server" message Can only Force Quit

  Just upgraded to El Capitan and cannot access the calendar. It opens with a message 'Moving calendars to the server.

  I cannot access all features and can be closed only by using force quit.

  Please stop calendar and also the application of reminders, runs. Force quit if necessary.

  Back up all data.

  If you synchronize some of your calendars, or reminders with iCloud, then in the iCloud preferences window, uncheck that marked calendars and reminders. You will be prompted to confirm that you want to remove your iCloud calendars and reminders of the computer. They will always be in iCloud. Re-check the boxes.

  If you synchronize agendas or reminders with another network such as Google service, please open the preferences panel Internet accounts. Make a note of the settings for calendar accounts, then delete and recreate.

  Launch schedule and see if there is an improvement.

• I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?

  I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?

  Don't see the menu bar not (File, Edit, View, history, Favorites, tools, help)?
  Turn on/off the menu bar is a new feature in version 3.6.
  (Linux and OSX see: what happened to the file, edit and view menus? )
  Windows Method 1. Press and hold the key and press the letters of the following in this exact order: V T M
  Windows method 2 Press and release the button. The Menu bar is displayed; then choose ~ ~ red: V ~ ~ iew > ~ ~ red: T ~ ~ oolbars and click on ~ ~ Red: M ~ ~ enu Bar.
  The menu bar should now be displayed permanently, unless you turn it off again using view > toolbars. Check = not displayed, NO check mark is not displayed.
  See: http://support.mozilla.com/en-US/kb/Menu+bar+is+missing

  Navigation, bar toolbar bookmarks and other toolbars under view > toolbars. By clicking on one of them will place a check mark (display) or remove the check mark (not shown).

  To display the status bar, view, and then click status bar to place a check mark (display) or remove the check mark (not shown).

  Mode full screen
  http://KB.mozillazine.org/netbooks#Full_screen

  See also:
  Back and front toolbar buttons or others are missing
  Customize controls, buttons, and Firefox toolbars

• 42RL833 - latest Firmware installed and cannot access the YouTube app

  I have 42RL833 Toshiba which is updated to the latest firmware, however I still cannot access the application on my YouTube. I get an error saying that Youtube XL is no longer supported.

  What can I do to fix this?

  > I get an error saying that Youtube XL is no longer supported.

  Google has stopped the YouTube XL service and, therefore, this service isn't available anymore.
  http://www.Toshiba.EU/innovation/generic/YouTube-XL/

  You can read details here:
  https://support.Google.com/YouTube/answer/3123170?hl=en

  It also seems that YouTube XL has been replaced by YouTube Leanback Lite:
  http://www.YouTube.com/leanbacklite
  See also:
  https://support.Google.com/YouTube/answer/3153576#

  There is also a note that if you can connect your computer to your TV, you can continue to use the YouTube TV-optimized experience by visiting youtube.com/tv.

• Cannot access the local admin page after first start

  Hello

  I am not able to access my newly purchased RN202, SN 45Y2535W003FC. I just plugged the power cable and turned on, but the power light keeps blinking even after hours. The NAS will connect to my local network with the ip 192.168.178.32 and ends by RAIDar under this address. However, the local admin under https://192.168.178.32/admin and https://192.168.178.32 page (even with http://) is not accessible. The connection is not accepted (cannot be connect-page in the browser). Also access more ReadyCLOUD is not possible, because the NAS cannot be discovered. Currently, there are no hard drives in the NAS. I also tried to insert a HARD disk already formatted in combination with a factory reset, but it does not work with the same result. It's already a replacement unit by my retailer the first device showing the same behavior, so I excluded a technical defect. What I am doing wrong? Any help would be greatly appreciated.

  Best regards

  Patrick Schmidt

  OK I found the solution by myself. Without a HARD disc inserted the NAS will not start correctly. As mentioned, I already tried to insert a HARD drive and then do a factory reset. Now, I saw that I have is to not properly place the HARD disk. If you open the lock on the grid (the thing in which you put the HARD drive), then you can not insert in the case completely and do not connect the connector of power und data. Maybe a little more detailed manual on it (for Dummies like me) would be useful. Argh...

• HP 15 laptop: laptop computer is connected to the wi - fi connection, but cannot access the internet

  Hello

  My problem is my WiFi says its connected but I can't browse or access the internet.it just tells me "unable to connect to internet computer is not connected to the internet", but my wifi says 'connected'.i tried to go to the cmd prompt and typed in "netsh int ip reset resetlog.txt c:\" goal it shows me "reset failed.access is denied .he don't s no user specified settings to be reset to zero." please "» What can I do?

  Thanks in advance.

  Hello @jerome256,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums, I would like to draw your attention to the HP Forums Guide first time here? Learn how to publish and more.

  I understand that you are having a problem with your WiFi and wanted to help you!

  You are trying to access WiFi through router?  If you are connected to your wireless network, but cannot access the internet, then the problem may be with the router.  Check that the router is connected to the internet.  If you have more than one router, then you can ensure that you are connected to the correct router.  You can also try unplugging the router for about 30 seconds, and then reconnecting it.  Please consult the following document, as it can help solve the problem for you:

  HP PC - Troubleshooting wireless network and Internet (Windows 10)

  Please let me know if this information has been helpful by clicking the thumbs up below.

  Have a great day!

• "Windows cannot access the specified device, path or file" for each X 86 application on a Windows 2003 x 64 server

  Hello

  I have a Windows 2003 X 64 server and since a week ago everything works fine.

  For a week or two when I try to run an X 86 application, I always get this error:
  "Windows cannot access the specified device, path or file.
  If I run a x 64 apps everything works fine.
  What made a mistake?
  Thank you

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows Server on TechNet. Please post your question in the TechNet forums. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• I get all the time can not download anything 'Windows cannot access the specified device, path or file. You can't have the permissions to access the have__appropriate element. »

  Original title: problems cannot do anything

  Windows cannot access the specified device, path or file. You can't have__appropriate the permissions to access the item. I get it all the time can not download anything

  Hi birdylod,

  ·         What version of the operating system is installed on the computer?

  ·         You did changes to the computer before the show?

  ·         You use Internet Explorer? If so, what version are you using?

  ·         What files you download?

  Follow these methods.

  Method 1: Performs a search using the Microsoft safety scanner.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Startup options (including safe mode)

  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.

  Method 3: Scan the file system (CFS) auditor to repair corrupted files.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  For reference:

  What to know before applying permissions to a file or folder

• I cannot access the application "contact me" when a website, get error "Default Mail Client not properly installed."

  I cannot access the application 'contact me' when a web site and receive the answer "Default Mail Client not properly installed" instead of going on the requested site.

  How can I fix this problem?

  Separated from the:

  http://answers.Microsoft.com/en-us/IE/Forum/IE8-windows_other/IE8-default-mail-client-not-properly-installed/23c2a9e1-d1fa-4a50-aeb1-90a6f2af717f

  CrystalBall © SEZ...

  Unlike Windows XP & Vista, Windows 7 does not include a default email Client. [What were thinking?]

  You will need to install a (e.g. MS Outlook;) Windows Live Mail; Thunderbird) , and then set it as a default for mail in CUSTOM (<>) article in Set Program Access and defaults of the computer , then restart your computer before any function send to or MailTo will become available.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In these forums, you will find support for Windows Live Mail: http://windowslivehelp.com/forums.aspx?productid=15

• Broadband went down for several days but was back on property that still cannot access the internet

  Went away for two weeks and return to find internet and landline phone at the bottom, contacted bt which were going out but it all came back to the top, light on bnroadband but still cannot access the internet!  Any answers please...

  Contact your ISP to solve problems.

• Cannot access the windows installer

  try to install itunes and other windows updates and I get error 643 on updates and cannot access the windows with itunes installation programs.  Is there something blocking these files that they do not work

  try to install itunes and other windows updates and I get error 643 on updates and cannot access the windows with itunes installation programs.  Is there something blocking these files that they do not work

  RE: Windows updates :
  You should be psoting in section updates from Windows:
  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  Here's the tutorial for number 643.
  Have a look while you wait for answers from the section updates to Windows.

  Windows Update error 80070643
  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80070643

  Re: Itunes
  You wrote. .. Cannot access windows with itunes installation programs.
  The Windows Installer Service could not be accessed
  http://www.Winhelponline.com/blog/Vista-the-Windows-Installer-service-could-not-be-accessed/

  Questions about Apple products will be better displayed on the Apple forums.
  It is where are the experts itunes and quicktime.
  Apple Discussion: Category: itunes
  http://discussions.Apple.com/category.jspa?categoryID=149

  Discussion of Apple - installation abd update itunes for Windows
  http://discussions.Apple.com/forum.jspa?forumid=792

  Problem installing itunes or quicktime for Windows
  http://support.Apple.com/kb/HT1926

  Uninstall and reinstall itunes and quicktime
  http://support.Apple.com/kb/HT1923

  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.