Cannot change the information in the header. Need quick help!

Similar Questions

• 23 - d160qd envy: new motherboard, now empty screen and 6 beeps. Cannot change the legacy BIOS. Help!

  Good ladies and Gentlemenof the Interwebulars, I hope someone can shed some light on my situation.

  Walked down one day to see that my computer would not start. A diagnosis which in a bad power port. Got a new motherboard because after desoldering (or that's what I tried to do) I realized that it was small to (re) welding in and I could not find the right part to reorganize.

  so I got a new motherboard. The number replacement part direct. Barefoot on my floor wood and ESD wrsitband on, I put in this bad boy. Double and triple check things and connections. Go to hit the power button and I get 6 beeps and 6 flashes of correspopnding of the powerbutton. The system does not appear to be on, fan is running with the other sounds of starting and running sounds, but I have a white screen and orange electric button. If I tap CTRL + ALT + DELETE it will restart and begin the process again. The 6 beeps by HP standards denotes missing graphics / card error. My original motherboard had a built-in graphics card so I thought that the same new part number card mother too. Obviously not. so I had a Geforce 2Go MXM graphics card update with heat sink. Barefoot, wood floor, bracelet ESD, thermal paste and turn it on to hear... SIX BEEPS AND SCREEN WHITE.

  After Googling around, some people say that I have to enter the BIOS and change boot legacy and fashion out of the UEFI mode that's killing me right now. I have join and would completely if I could see my screen of the BIOS, or anything for that matter. I can not go back also to my other card because it will not feed. So my question; How to make or change the BIOS settings so that my computer will recognize a graphics card or internal graphic that should be on the new motherboard itself so that it starts?

  I need this computer for CAD work soon so I thought help processor i7, 8GBs RAM, Geforce card and touch screen to perform a generation of PC.  So if someone has a great idea they would projected upward on this post, I'd appreciate it. Thank you!

  Your computer is not posting, sound rather give an error message in the form of 6 beeps and red LED flashing, indicating graphics / video issue.

  You can never get into the BIOS of the device, if its not posting, not on a HP Desktop atleast.

  I recommend, you disconnect all components and fittings connected to the motherboard i.e. cables SATA, power cables, RAM, processor, heatsink, power supply and battery CMOS as well.

  Now, press and hold button power unit for a minute or two., with the power and everything is still disconnected.

  Then,.

  (1) Insert the battery CMOS back into its slot, install the processor and the heat sink, connect all cables power that goes to the motherbaord in the PSU and CPU and etc., less SATA cable and cable power to drive hard and Optcal drive and turn on the device, of course after you have connected the rear power cable.

  (2) check if the machine beeps and check whether it is 5 times.

  (3) If yes install a memory in the first slot (slot black), connect the monitor and turn on the power and check if there is no video output.

  (4) if so, connect the return which is always disconncted, to their respective locations and ports and turn them the unit on and get on with your CAD stuff.

  IF NO,

  2 options:

  (1) if the unit is still under warranty, call 1800-474-6836 and have a technician on-site visit your place and replace the parts needed for the operational unit.

  (2) or the motherboard you purchased could have been Dead On Arrival. Get a warranty replacement for the DOA mobo and re install a new Board of Directors.

  Good luck!

  Please click on the "congratulations, Thumbs Up" at the bottom of this post if you want to say 'Thank you' for helping!
  Please click "Accept as Solution" If you feel my post solved your problem, it will help others find the solution.

• Cannot change the screen resolution. Help, please

  I recently reinstalled Windows XP (service Pack2) on my computer and restored the office to the factory settings. Now, the screen resolution is stuck at 640 x 480 and 16-bit color quality as this was not a problem before. The screen that appears under 'type of screen' in the advanced settings menu says "default monitor" and the properties button is not clickable. I tried to connect another monitor to the PC, but it doesn't help. Can someone help please I really need to change the resolution of the screen to a higher quality? Also, the PC has an internet connection if that makes a difference. Any help is greatly appreciated. Thank you.

  ... What other drivers in addition to the graphics card and network card should I try to install?

  In fact, those who are newer than your current drivers.

  I understand your reasoning for installing the monitor driver, however, I'd personally chipset (motherboard), video, audio and network (LAN) first. After updating the video driver, there is a chance that it recognises so the screen correctly.

  I don't know if you have reinstalled Windows XP from floppy disks to install Windows or Dell installation/recovery disks or partition restore hidden, but nevertheless, the drivers that were installed during installation is as new as the installation media. Given that the media are at least 5 years and more (maybe 8 years and more), there is an excellent chance that all the material and device drivers have been updated.

  If you know the serial number or the Express Service Code on your machine, you can enter the page linked below and it should display all the downloads available for your computer. Otherwise, you may need to select one of the options under No., for example to choose from a list of all Dell products (it does not list a Dimension 1100/B110 that has many drivers/downloads available).

  Driver downloads &
  http://www.Dell.com/support/drivers/us/en/usgen1/DriversHome/NeedProductSelection

  The page linked below contains a lot of good informaiton, including a list of drivers and downloads that may be available. I think that Section 3: how to determine the components in my computer? and Section 4: how to download and install a driver will help you get the correct drivers for the hardware devices in your computer.

  How to use drivers and downloads website
   http://support.Dell.com/support/topics/global.aspx/support/KCS/document?c=us&CS=19&l=en&s=DHS&docid=DSN_324722&isLegacy=true

  The page linked below describes the order in which Dell recommend for installing drivers.

  How to download and install drivers in the correct order
   http://support.Dell.com/support/topics/global.aspx/support/KCS/document?c=us&CS=19&l=en&s=DHS&docid=DSN_1A0C0937D62A8739E0401E0A55174744&isLegacy=true

  Kind regards

• Cannot change the width of line - help?

  I have problems with the option of running in illustrator. It was working fine but now its dead end at 1 point and I can not increase or decrease the width of the line: no matter what I do. Help, please.

  Select the path... Clear the snap to grid of pixels on the table to transform (window > transform)

• Cannot change the font color on the desktop icons

  I am running windows vista. I can't change the font as in windows xp. No matter if the background is dark or the police is always black... Help!

  Hello

  Thanks for posting the question in Microsoft Answers.

  I apologise for the inconvenience.

  Unfortunately, you cannot change the font color of desktop.

  Because desktop wallpaper images have different colors, it is easy for the colors of unreadable fonts if they are on top of the same color in a background image to display. For example, a black font on top a dark part of the background image or a white font on a white part of a background image.

  The desktop icon fonts are dynamic and show white on dark background and change in white with a shadow effect black on a light background.

  In previous versions of Windows, it did not matter what color you chose to fund policies, some would still make invisible because of the background color of a desktop wallpaper. The user was constantly moving icons around the desktop computer to another colorful area where the police could be read. This was the source of a large number of complaints from users asking for a policy that was still visible, regardless of the color that was behind the police.

  However, you can change the theme and see if that helps:

  Change desktop theme:

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-desktop-theme

  Hope this information helps. Let us know if you need additional assistance. We are happy to help you.

• Cannot change the name of the file in the file properties.

  Original title: Cannot change the file properties

  Some downloaded files have a value in the box "title" under the details (after clicking Properties)
  I can't remove this 'title' and it appears so when I share the file on my network.
  The file is located on a portable hard drive, but I tried to move some files from problem to my office to see if I could solve these problems there, but nothing has worked.

  I already have
  -taking possession of the object
  -allows full control for all users
  -tried to use the "attrib - r + s' function
  -among other...

  I just want to know if there is a way to change the details of the file. On another windows help page it says something along the lines of "some attributes cannot be changed" I hope this isn't the case.

  Any help at all would be great, if no additional information is needed let me know.
  Thank you

  This information is set when the file is created.  Windows has no native ability to change.  You need a third party program.  For example, see link below.  Note that I have no idea if it's any good or works in Windows 7.  Gives you the link just to get an example of what to look for.

  abcAVI Tag Editor
  http://abcAVI.kibi.ru/

• Good for laptop - cannot change the ISP; keep returning to a previous provider

  Windows 7 laptop of my grandson, I'm migrating FIREFOX (excellent resource!) of my aging XP desktop. An existing Mozilla installation on the guarded device tries to connect to an ISP in Sydney (1000km) which kept out, I guess because the signal is too weak. Too far - on the Internet?

  Reinstalled my new ISP contact, reinstalled a fresh copy of Firefox, copied the old profile XP (just underneath the random string file name), but cannot change the fault. Firefox at startup tries to raise the old ISP (Sydney) and expires, and then allowing me to establish a manual connect with the ISP (my current) new.
  Perhaps a clue: in my Firefox troubleshooting info, change preferences, the browser start page is the address of 'old', with 'override mstone' ignore, what look like prints of registry entries, but I can't change all that - and maybe it's wise! An annoying secondary question: on arrival, the laptop listed no administrator user. So I am me came as an administrator, but I wonder if a past or current even Admin hidden could register (or other) entered resistant to change.

  Late discovery: the laptop is apparently infected with browser pirate btsearch.name. Search Google throws a series of removal procedures, and I'm now working through them.
  What Miss me?

  Sometimes a problem with Firefox can be a result of malware installed on your computer, you may not be aware of.

  You can try these free programs to search for malicious software that work with your existing anti-virus software:

  • Microsoft safety scanner
  • MalwareBytes' Anti-Malware
  • Anti-Rootkit utility - TDSSKiller
  • AdwCleaner (for more information, see this other AdwCleaner download page)
  • Hitman Pro
  • ESET Online Scanner

  Microsoft Security Essentials is a good permanent antivirus for Windows 7/Vista/XP, if you do not already have one.

  More information can be found in the article troubleshooting Firefox problems caused by malware .

  This solve your problems? Please report to us!

• I signed on XP Pro SP3 as an administrator but you cannot change the timing of Windows Update to 03:00. All options are not enabled. How can I change the time, updates are made? __

  I signed on XP Pro SP3 as an administrator but you cannot change the timing of Windows Update to 03:00.  All options are not enabled.  How can I change the time that updates are made?

  Hi imoffshore,

   

  Welcome to Microsoft Answers Forums.

  We would like to get some more information from you to help solve your problem. You better, please answer the following questions.

  ·         When was the last time it worked?

  ·         Remember to make changes to the computer recently?

  ·         You have security software installed on the computer?

  ·         You get the error message?

  When you open the tab automatic updates in the control panel or My Computer property sheet, all options of configuration of the automatic updates may be grayed out. This happens due to one of the following reasons:

  1. You are not logged as administrator (or equivalent)
  2. Strategy of automatic updates is enabled
  3. Automatic updates (and Windows Update) access is blocked by group policy

  The options available for automatic updates.

  You must make some changes in the windows registry.

  Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756

  • Click Start, run and type REGEDIT to . EXE
  • Go to this location:

  HKEY_LOCAL_MACHINE-SOFTWARE-policies-Microsoft-Windows------WindowsUpdate------AU

  • In the right pane, delete the two values AUOptions and NoAutoUpdate
  • Go to this location:

  HKEY_CURRENT_USER-SOFTWARE-Microsoft-Windows-CurrentVersion------policies------WindowsUpdate

  • In the right pane, delete the DisableWindowsUpdateAccess value

  Using the Group Policy Editor - for Windows XP Professional

  • Click Start, run and type gpedit.msc
  • Navigate to the following location:

  => Configuration of the computer
  ==> Administrative templates
  ===> Windows components
  ===> Windows Update

  • In the right pane, double-click Configure automatic updates and set it to not configured
  • Next, go to this location:

  => User configuration
  ==> Administrative templates
  ===> Windows components
  ===> Windows Update

  • In the right pane, set to remove access to all Windows Update features on not configured

  Change how Windows installs or notifies you of updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-how-Windows-installs-or-notifies-you-about-updates

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error: Windows cannot change the password when attempt to set a password to connect to the Windows XP computer.

  Original title: Windows cannot change the password.

  I'm trying to set a password on my computer with windows xp professional and everytime I try, I get a message saying: Windows cannot change the password. Please can someone help me.

  With our thanks

  Elizabeth

  Hi Elizabeth,.

  You can follow this link & check if the problem persists:

  Impossible to change the password for the administrator account in user accounts in Control Panel

  Hope the helps of information.

• Cannot change the Vista hosts file

  I started Notepad as administrator and open my hosts file, made my changes, but when I try to save it I get this message: cannot create the c:\windows\system32\drivers\etc\hosts file verify that the path and the name are correct

  How to save this file? Thanks for any help!

  Hello

  The host files are linked to the internet explore and this is why it must be very careful when you change them. And this is the reason why they were safe as to change. We have a FixIT tool to assign default host files. It's here.
  http://support.Microsoft.com/kb/972034 also, here is the article that explains how to change the host files and the Lmhosts file in Windows Vista and Windows 7. You cannot change the Hosts file or the Lmhosts file in Windows Vista and Windows 7
  http://support.Microsoft.com/kb/923947

   

  I hope this information helps you!

• Cannot change the hosts file in Windows Vista Home Premium

  Posted on behalf of a client:

  Cannot change the hosts file in Windows Vista Home Premium. Read-only value.

  Help, please.

  Hello

  I suggest you to try the steps below and check if it helps.

  Method 1: Try to take possession of the host file and check to see if the same problem happens.

  To apply permissions to a file or a folder:

  a. right click on the file or folder and then click Properties.

  b. click the Security tab and then click Edit.

  c. do one of the following:

  ·         To set permissions for a user who is not listed under group or user names, click Add, type the name of the user or group, click OK, select permissions and then click OK.

  ·         To change or remove permissions for a user or an existing group, click the name of the user or group, select the permissions and then click OK.

  For more information, see the article mentioned below:

  What to know before applying permissions to a file or a folder:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-access-denied-when-opening-files-or-folders

  Prevent changes to a file or folder (read-only):

  http://Windows.Microsoft.com/en-us/Windows-Vista/prevent-changes-to-a-file-or-folder-read-only

  Hope this information is useful.

• Microsoft Movie Maker - cannot change the length of each clip.

  Cannot change the length of each clip on Microsoft Movie Maker.

  I clicked on 'tools', then 'options' in Microsoft Movie Maker after importing my media and organize my clips as the way I would like it. When I then click on the "Advanced" tab, image duration shows only 5 seconds with the transition period only 1.25 seconds, which is the default setting and that is also what I want. However, when I play my project in Movie Maker, it accelerates through each clip. I also noticed that when I press the title of 'Clip' in my headings at the top left and then click on 'Properties', the duration of each clip shows that only 00:02 seconds. Which is why my speed clips too quickly.

  I would have thought that setting my time of duration in the Tools section would then set in the Clips section, but this is obniously does not. I don't understand why everyone would show differently and wonder if you can help me to slow down the speed that my movie is playing.

  Thank you

  Cannot change the length of each clip on Microsoft Movie Maker.

  I clicked on 'tools', then 'options' in Microsoft Movie Maker after importing my media and organize my clips as the way I would like it. When I then click on the "Advanced" tab, image duration shows only 5 seconds with the transition period only 1.25 seconds, which is the default setting and that is also what I want. However, when I play my project in Movie Maker, it accelerates through each clip. I also noticed that when I press the title of 'Clip' in my headings at the top left and then click on 'Properties', the duration of each clip shows that only 00:02 seconds. Which is why my speed clips too quickly.

  I would have thought that setting my time of duration in the Tools section would then set in the Clips section, but this is obniously does not. I don't understand why everyone would show differently and wonder if you can help me to slow down the speed that my movie is playing.

  Thank you

  ================================
  The change of setting to: Tools / Options /.
  Advanced... tab applies only to the added clips
  to the timeline * after * you change the setting.

  If you switch to view "Storyboard" and select
  all of the clips as a batch (select one and the type...
  CTRL + A)... you can add the 'Speed Up, Double.
  or "Slow down, half" effect of changing the
  duration. Simply select all clips / right click
  the effect on the menu... Choose...
  Add to storyboard table.

  'Speed Up, Double' cuts the duration of half.

  "Slow Down, half ' double life.

  These effects can be added up to six times.

  If you need finer adjustment...
  the info may be useful:

  You can change the duration for each clip
  manually. Move your pointer autour the
  edge of an element until you see a double red
  arrow. Now, drag the double red arrow...
  you will see if show a ToolTip displays the duration
  train to change.

  Or... just to redo the project after changing
  the long-term: Tools / Options / Advanced
  tab.
  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• You cannot change the administrator account

  Original title: sdasdasdas

  I ca't change on my computer, my OS is windows 7 when I try to change administrator, it asks for a password when I put my password it say "" connection failed: the user did not request type of login on this computer "for this reason I'm stock on my user account and I can not install all the tools" because he has an administrator privileges. pls help me. ?

  Hello

  It seems that you cannot change the administrator.

  Perform the steps mentioned below and see if it helps.

  a: Click Start and type gpedit.msc in the Start Search area and press on Enter.

  b: Navigate to the following location
  Computer configuration / Windows Settings / Security Settings / Local political

  c: Under this click user rights assignment.

  d: Double-click access this computer from the network and verify that EVERYONE is added to the list.

  e: Otherwise add it by clicking Add a user or group , and then type EVERYONE, click OK and then apply and OK.

  Hope this information helps.

• Cannot change the type of data in the columns referenced by foreign keys

  Hello:
  
  I'm using Version 3.1.0.691 and change the types of data in many columns of data derived from the field types. If a column is referenced by a foreign key, however, the data type radio buttons are grayed out. I suppose that if I deleted the foreign key, that I would be able to change the data type of the column to a field, but that would be tedious. Is there another way to go about this?
  
  Any help would be greatly appreciated.
  
  Thank you
  
  Doc

  Hi Doc,

  If a column is referenced by a foreign key, however, the data type radio buttons are grayed out.

  It is not good - if you have the PK column, and it is called by another FK column you can change the data type of column PK and FK column data type will follow the change. You cannot manually change the data type of column FK. Good column PK itself could relate to another column, and in this case you cannot change the data type of column PK.
  In your case - you need to find the first PK/Uk column that is not the column FK itself and change its data type. FK columns in the chain will follow.

  Philippe

• Cannot change the incoming mail server. no text highlight

  I am unable to send mail from my Mac.  No problem with iphone or iPad. Cannot change incoming mail server as text is not highlighted.  Cannot change the server for outgoing (SMTP) mail. Cannot change the list of SMTP servers. Says offline.

  Hi Granny Smith 1.

  Thank you for using communities Support from Apple. Sorry to hear that you are having problems with mail. It's a little bit clear exactly what you see when you say that you cannot change any server info, but if you continue to have problems sending or receiving mail, you will find the troubleshooting steps in the following article useful:
  

  If you cannot send or receive e-mail on your Mac - Apple Support

  Kind regards.

• Cannot change the Apple ID

  I'm changing my Apple ID, but when I try to change ID, it does not show the ability to 'change e-mail address '.  How can I get that option?

  You cannot change the name of the device.

  Sign of your ID, then click on my Apple ID and change the ID (you can not change if it's an address to iCloud)