cannot connect to database of point 12 c-mount is filled

Similar Questions

• Cannot connect to Internet access point except on a Jetpack from Verizon.

  I am running Window 7 Home Premium. I can connect to the Internet using my Verizon Jetpack and nothing else. I tried to use my Verizon phone as a hotspot, I have a router Belkon 4. 1A and we tried through other points of access. It connects to the access point according to the plan, but it is XE offline to the Internet. I tried to update my drivers for wireless devices, and it is said that they are already updated.  I can connect when I'm wired. When I check properties properties IPv4 and IPv6 are shoddy outside. Install is the only thing not frayed on. When click on install, I get an error: cannot add the requested feature. the error is: these data are incorrect.  My wireless adapter is Realtek RTL8187SE Wireless LAN PCIE network adapter. Please help me I am so frustrated.

  Hi Sylvia,.

  I imagine the inconvenience that you are experiencing.

  Here are some ways you can follow to resolve the problem:

  Method 1:

  Check out the link and follow the steps in the article:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Method 2:

  Flush the DNS and request a new IP address of your ISP server by following these steps.
  a. click on start
  b. click on run
  (c) in the Run dialog box type cmd.exe and click OK
  d. in the command prompt, type the following.

  e. ENTER after each new line.
  ipconfig/flushdns
  ipconfig/release
  ipconfig / renew
  output

  Method 3:

  This problem may be caused by incorrect DNS settings. following these steps and check:

  a. click "Start", enter "NCPA. CPL"(without the quotes) and press ENTER.

  b. right-click on the connection you use for the local connection, and then click "Properties".

  c. Click to select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.

  d. in the Internet Protocol window, we will change the "Preferred DNS server" to 208.67.222.222

  e. click 'OK' twice to complete the change.

  If the problem persists, please repeat the steps and change the "Preferred DNS server" to 208.67.220.220.

  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• Cannot connect Blackberry mobile access point using Windows computer.

  Original title: connection problem

  I use windows 8 on my hp15 and also a cell phone blackberry q10... I noticed that the hotspot from my phone does not appear on the windows network. but hotspot of the else phone shows and connects perfectly well and my q10 hotspot shows and connects on their own computer... any idea on what could be the problem?

  Hi Adam,

  Thanks for posting the query on Microsoft Community.

  If I understand correctly, you are unable to connect the mobile access using Windows computer point. Don't worry, we will help you with the question. It could be matter of settings.

  Manage the network and other utilities mentioned in the link below and check if it helps.

  Why can't connect me to a network? :

  http://Windows.Microsoft.com/en-us/Windows/cant-connect-to-network#1TC=Windows-8

  Also try the other steps in the link below.

  Mobile broadband from end to end:

  http://Windows.Microsoft.com/en-us/Windows-8/mobile-broadband-from-start-to-finish

  For reference:

  http://BTSC.webapps.BlackBerry.com/BTSC/ViewDocument.do?externalId=KB31857&sliceId=2&DOCTYPE=KC&noCount=true

  http://docs.BlackBerry.com/en/smartphone_users/deliverables/55574/mes1342811963579.jsp

  I hope this helps to solve the issue. If the problem persists, get back to us. We will be happy to help you.

• Quicken 2011 software cannot connect to the internet, points to a firewall configuration issue.

  I am running Vista and other programs work. Any ideas on what I should do? How do Dell firewall. I am concerned about lowering my firewall settings.

  Hello

  1. could you give us the exact error message?

  You can have a look at the following link on the Quicken support Web page.

  Error when using Online Services: OL-297

  http://Quicken.Intuit.com/support/articles/online-services/download/4151.html

  For the Dell Firewall setting, you can visit the Dell support Web site:
  http://support.Dell.com/

  For more information about Windows Firewall, see:

  http://Windows.Microsoft.com/en-us/Windows-Vista/Understanding-Windows-Firewall-settings

  I hope this helps.

• cannot connect to the database

  Hello

  on 10.2.0.3

  In my listener.ora, I gave port 1521.

  In tnsnames.ora also 1521.

  When I try to connect to my db I get:

  sqlplus system@MYDB

  ORA-12514: TNS:listener is not currently of service requested.

  in listener.log I

  07 NOV. -2013 09:04:54 * (CONNECT_DATA = (SERVICE_NAME = MYDB) (CID = (PROGRAM = D:\oracle\bin\sqlplus.exe)(HOST=SERVER)(USER=user))) * (ADDRESS = (PROTOCOL = tcp)(HOST=127.0.0.1) (PORT = 4358))))

  or

  (ADDRESS = (PROTOCOL = tcp (PORT = 1858))(HOST=127.0.0.1))

  or

  (ADDRESS = (PROTOCOL = tcp (PORT = 1869))(HOST=127.0.0.1))

  In sqlnet.log I

  AMT-12564: TNS: denied connetion

  My question is why in listener.log I have different port numbers instead of 1521?

  Thank you.

  user10274093 wrote:

  Thanks Hoek.

  I cannot connect to the database on the server hosting then no use of the customer.

  I don't see in these links, something on the port number change in listener.log.

  Kind regards.

  Port 1521 is used to communicate with the listener.  If the listener is able to actually process the request (your error indicates it is NOT able to process the request), while it generates a server process that communicates with the client on a different port.  At this point, the listener is out of the picture until the connection goes.

  Read the links once again, especially the other, which directly addresses your specific error message.

  And know that the requests to the IP 127.0.0.1 (or its alias 'localhost') never to leave the machine for which the request was made... your log listener seems to indicate that is used, but if that were the case, you would have got a different error.  If you read the links provided, you will see that the first centerpiece of the ora-12514-related news is the release of "lsnrctl status".

• Cannot connect to my Satellite A210 adapter for access point

  Hey everybody...

  I have a little problem with my wireless. We have some books and access point. Everyone can connect to access point except me. I have the Satellite A210-127. Do you know where is the problem? How can I connect to the access point?

  Thank you

  In a first time, you must activate WLAN antenna correctly. Upon first use WLAN switch and set it TO position (the LED will be ON). Next step is to use the FN + F8 key combination. Don't forget THAT WLAN is enabled.

  After this use please ConfigFree radar to see if the access point is visible for your laptop.

• Cannot open the synaptics pointing device in windows vista, upgrades are far but message error, unable to connect to the synaptics pointing device

  Hi I have a problem with my mouse/pointer when I click on the mouse to open it I have error message unable to connect to the synaptics pointing device. Have you checked the updates that are up-to-date, and the driver is ok, not sure what to try next need to make any changes to the mouse pointer

  with Brice thanks.

  Hi paiyay,

  Thanks for posting in the Microsoft Community.

  I understand that you are unable to open the synaptics pointing device in windows vista

  · You did changes to the computer before the show?

  · What happens when you click the Yes button in the error message?

  · You are able to use the mouse on the system?

  I suggest you uninstall the software from programs and features and then try to open the properties of the mouse and check if you are able to open the mouse properties then I would you recommend to uninstall the drivers that are installed on the system in the Device Manager and then download the drivers from the link below and check if the problem is resolved.

  http://www.Synaptics.com/support/drivers

  http://www.Synaptics.com/resources/drivers

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Connect the hard disk, and then try running the fix tool of the article below and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/

  I suggest you to contact the mouse manufacturer for assistance. Click on the link below.

  http://www.Synaptics.com/

  See also:

  FAQ and troubleshooting

  http://www.Synaptics.com/resources/consumer-tips

• A Wi - Fi connection does not have an IP address and cannot connect to Internet

  Here's my question:

  "Wi - Fi doesn't have an IP address and cannot connect to Internet"

  But he connects.  I use the model of airport Time Capsule ME182LL/A and the last OS.

  The reason why I suspect the problem is that my Samsung smart TV will not connect to internet, but connects to the WiFi.

  Do I have a problem when the network preferences indicates my network with a point orange and says 'No IP Address'?  It doesn't have a green dot next to the Wi - Fi connection and it says connected.  I'm puzzled.

  Thanks for any idea that you can provide.

  Something wrong with the Setup program.

  After the airport utility screenshots of the configuration of TC.

  In particular this modem do you have? Actual spending brand and model please.

  Who is your ISP?

• Cannot connect my Satellite L20 to AP

  Hello
  I have a satellite L20-214, just bought it and an edimax 7205 ap.
  Both supported the 80211b specifications.
  Access to the AP is completely open!
  But I can't get the laptop to connect.
  He sees the network in the list, but it just cannot connect to it.
  I tried all settings,
  The access point works perfect with smc cards and a few old books.
  I set all the possible settings in the config of Toshiba, disabled the encryption, change the channel to 1 because it is the channel of pref. of the ap and choose 80211b as prim.

  For now, I'll give some further tests before I have to return the laptop to the store because it's brand new.

  But I hope someone has an answer for me.

  [Edited by: admin on 28 May 06 06:28]

  Hello

  Also check if you can find the latest version of the driver for the WiFi card. Also check Intel download page under http://downloadfinder.intel.com/scripts-df-external/Product_Filter.aspx?ProductID=1637&lang=eng

  Good bye

• Equium M50 cannot connect to Wifi b

  Hi, my M50 cannot connect to my wireless b router, it can connect to my network of friends g. The router has been tested with other laptop & works very well. Also can't update driver Wifi support page.
  Andy

  Hello

  Have you seen no yellow exclamations points in Device Manager in the section of wireless LAN card?
  Have you activated the card wireless switch on the side of the laptop and with the FN + F8 key combination?
  Please check these options.

  Good bye

• Satellite A505 - sees, but cannot connect to, Wireless Router Win7

  I have a laptop Toshiba A505-S6980 running the 64 bit version of Windows 7.

  It worked fine a few months previously, to connect wireless to my O2 2 wireless router (the notebook has a REALTEK RTL8191SE wireless card).

  I also have a desktop running XP computer that I use to connect to the same router. While on the desktop, I noticed several weeks ago that the router has been implemented with no WPA and WEP security, so I decided to change the router to WPA. The desktop PC was fine with this, but the laptop complained and wouldn't connect, failure of authentication and just stating "unable to connect to xxxxx". At the time I assumed it just couldn't handle the WPA authentication for some reason any and decided that I would probably turn to WEP to a later date to make it work again. At some point, I remove a ' O2 Connection Manager ", which had been installed when I bought a 3G dongle O2, where he has confused the issue, but it made no difference. In the meantime, I tried to connect the laptop using a wired connection and worked well.

  I now (a few weeks later) decided that I wanted to use the wireless laptop then redefine the router to WEP expect this to work, but it didn't. As with WPA, he did not get past authentication when I put the key to security in. So, I try to understand the problem...

  What happens;

  (1) the wireless laptop sees my router (and neighbors), but just cannot connect.

  (2) I can connect with a laptop computer on the same USB wireless adapter.

  (3) I can connect the laptop to the router using a wired connection, and there is no problem.

  (4) my desktop running XP computer can connect to the router as WEP or WPA Wireless if the router is ok.

  (5) this worked several weeks ago!

  What I've tried;

  (1) I have installed the latest REALTEK RTK8191SE driver.

  (2) I tried to disable the security on the router, no joy.

  (3) I deleted all the profiles of network on the laptop.

  (4) I have tried with Norton antivirus and firewall disabled (but have not uninstalled) but no help.

  (5) I tried to do a restore of the system to the closest possible point and no help.

  (5) I uninstalled the wireless network adapter and its driver in Device Manager... Windows 7 can see the of it after a reboot and re - installed (using the old default driver), but it does not work. Then, I re-installed the latest version from REALTEK to ensure that it is up-to-date.

  What's weird is that

  (1) it works ok using the wireless USB adapter

  (2) the integrated REALTEK wireless adapter works to a point such that it can SEE my router, connect simply do not

  (3) authentication failure almost instantly

  My suspicions are that an automatic update of Windows 7 or the O2 Connection Manager has somehow screwed it upward. I have uninstalled the O2 connection manager and tried to uninstall the automatic updates but there are many of them and I don't know how far back, I need to go. Also, because it authentication immediately, it seems that it is not giving him a chance to actually work.

  Does anyone have any ideas on how I can proceed or had a similar problem?

  This is a really silly situation. In any case, I recommend you to use the Toshiba WLAN drivers only.
  I put t know what Realtek module is inside but try please install driver WLAN http://aps2.toshiba-tro.de/wlan/?page=downloads

  All that you have done is logic and I think I will try the same thing.
  Have you tried to connect to WEP or WPA is disabled? I mean free WLAN without protection.
  Have you tried to connect your laptop to a friend's router?

  I really put t know what is the problem here but there are a few bad setting it.

• Cannot connect Tecra 9000 to wireless network

  Hello

  I am trying to connect my laptop Toshiba T9000 to my BT home Hub 2.0 Wireless v but a little difficulty.
  The laptop recognizes the hub, but every time I click on connect, I get the same message.

  ""Windows cannot connect to the selected network. " The network can be is no longer in range. Please refresh the list of available networks and try to connect again"

  I went through a few troubleshooting steps to resolve this problem, but always without success.
  Can I update the driver? My inclination is that this may have something to do with the laptop is not able to support WPA?

  I am not very computer but if anyone has any additional input to help me with this question then I would be very happy.

  Kind regards
  Answer by quoting

  > Can I update the driver? My inclination is that this may have something to do with the laptop is not able to support WPA?
  This may be possible

  The point is that this laptop is an oldie and the wireless network adapter appears to be old too.
  I ve no idea what WLan card you have, but you could try to connect to the WLan without use of encryption settings. Disable encryption on the router Wlan and test connectivity again. of course, this must be done only for testing purposes
  The wireless network must be always secure

  The alternative could be the use of external USB WLAN, it would be the easiest and fastest way for that to be resolved

• Tecra M1 cannot connect wireless

  Hello

  This new but I hope someone can help me.

  I'm having difficulties to connect to a wireless network with my Tecra M1. I think that the problem could be with the card Intel (R) prowireless MiniPCI LAN.

  I tried to reinstall the driver for it, but nothing worked. I access the access point Via a cable but cannot connect wireless.
  I reinstalled the software PROSet I printed user's guide, and he tells me if he have Driver version "1.2.4.41". I have Driver version "1.2.5.34" installed on my laptop and this seems to be the only one on the Toshiba site, so I can't find "1.2.4.41" to install instead of '1.2.5.34 '.

  Any ideas where I can find this driver? I tried to let windows manage my wireless connection but not able to connect. I also tried free config but it couldn't connect either. All above can see the available network but cannot connect. Any ideas on a resolution. I am trying to connect via a router belkin G + MIMO.
  No problem connecting via a direct cable.

  Thank you

  Hello

  have you tried to connect with another machine to check if it works?
  Otherwise, I suggest the following things:

  -Disable all security features
  -update the firmware on your router
  -dhcp instead of IP´s sets the value
  -read the manual of the router, sometimes they have weird parameters

  and finally and most importantly, try to connect with your M1 to another access point to make sure that you connect your machine to a wireless network.

  Welcome them

• Windows cannot connect to the printer. The name of the printer has been correctly entered, or the specified printer has lost its connection to the server.

  A Windows Server 2003 Standard Edition SP2 32-bit computer is a field, the file and print server.

  A computer on the domain is a machine of Windows 7 Ultimate 64 - bit with HP DesignJet 500 24 printer connected via USB.  The printer is running the latest firmware.  The PC is running the latest 64-bit drivers with no problems to the host machine printing.  The host also has the latest drivers 32-bit (x 86) installed by downloading by other computers on the network.  The printer is configured to share with the share name of HPDJ500.

  Now, on a machine Windows XP Pro SP3 32 bit on the field, I'm trying to connect to the shared printer.  Add a printer > click Next in the wizard of > check "a network printer or a printer attached to another computer" and then click Next > click on "Find a printer in the directory", then click Next > click Find now > HPDJ500 in the list below (the XP machine can see the shared printer on the Windows 7 computer!) and click OK.  At this point, I get an error that says: "Windows cannot connect to the printer.  The name of the printer has been correctly entered, or the specified printer has lost its connection to the server.  For more information, click Help. »

  Alternatively, if I right-click on the HPDJ500 printer listed, then click on connect, I get the same error message but I also see a separate window that says "Connecting to HPDJ500 on H2.ws.net" with the lively projector.  This window also disappears as soon as I clear the error message.

  Please note that this printer worked perfectly as a printer shared, hosted on a machine XP 32 bit on the field.  It works perfectly for the new Windows 7 64-bit machine, but we cannot connect from anywhere else on the network (including the server which translates the same exact error message).  On the server, I also preinstalled drivers thinking there was a problem with a 32-bit computer, trying to grasp the correct drivers from the host 64-bit Windows 7, but that doesn't change anything.

  How connect to this printer?

  Try using the path UNC path of the printer in the Add Printer Wizard.

  Add a printer > network printer > connection to this printer ((deuxieme point)

  Click next to browse (leave blank, the name field) or type the UNC path of the printer (i.e. \\Computername\Printername) path

• Acer One S1002 cannot connect to Wifi

  I just bought a S1002 an Acer (windows 8.1) last night and connected to the wifi at home. No problem. I get out and continue to downtown, then select wifi that I want to connect, and the State of WiFi sticks on "Checking network requirements" before saying that he cannot connect to the network. I don't not even at the point of application is the password for the network before the connection fails.

  I can't call the @# $& * (% ^ @# & * (% ^ * (! & $^ Acer customer support because they print the) @* (#& % ^ @# & * $% series information both @# $* (& % ^ @# $* (& % ^ small.)))))

  I tried Windows help pages, and they say that it is the router, and I need to solve a problem with the router. My iPhone and iPad 2 Nextbook can all connect both at home and at work WITHOUT a PROBLEM.

  Anyone have any ideas on how to fix the Acer One wifi to connect?

  vampiresharker wrote: I can't call the @# $& * (% ^ @# & * (% ^ * (! & $^ Acer customer support because they print the) @* (#& % ^ @# & * $% series information both @# $* (& % ^ @# $* (& % ^ small.)))))

  Anyone have any ideas on how to fix the Acer One wifi to connect?

  I use my phone to take a picture, then blow up the images to read the tiny letters usually.

  I guess you have already forced the tablet to forget the network, rebooted and then retried connecting? It is sometimes difficult to get them to really forget a wrong entered password.