Cannot connect to the router interface because it calls windows security credentials

Similar Questions

• Help! Setup Wizard cannot connect to the router!

  I tried several times to install this router wireless MO # BEFW11S4.

  I get an error message that Setup Wizard cannot connect to the router!

  I pressed the reset on the back button each time, it is turned off, check the cable connections between the modem cable to the router, then router to the computer.

  After dropping out of the router and connect the PC to the top with the modem, the PC is then connected to the internet once more.

  How to solve problems, or isolate the problem as a bad router?

  Please send me a PM for any suggestions or help.

  Thxx

  (Note to mod: Email address removed.)

  Thank you very much this has helped. You don't mention there was a button "generate" to create the password agorythm code to use as a password.

  Thank you! Problem has been resolved.

• Smart Wi - Fi cannot connect to the router

  I can't access my router remotely. It is said that my router has no internet connectivity, but I can access the Internet fine when I am connected to the router locally. Somewhere that my modem is using the bridge to do this, I met and so I tried to fill it, but I still get the same message. Tried changing from dhcp to pppoe, I read somewhere, but my ISP does not seem to support. The router firmware is updated. Help, please. Never been able to use this feature because I bought the router.

  You'll probably have to do a factory reset and set up again. There could be other things to try, but it's the easiest way. If you have a large number of special configurations, you can save the config before you perform the reset of encephalitis in ticks and once that you have reset it and see if it is accessible, then restore settings.

• WRT160NL cannot connect to the web interface after firmware update

  I've updated the firmware to unofficial http://mirwifi.org/download/fw/WRT160NL/wrt160nl-0.1.3-pre5.bin and since then I can not connect to the router through the web interface. What can I do? Is it possible to update the firmware to the official without web interface? Thanks in advance for any help.

  The router's default IP address is 192.168.1.1. Try to ping the IP address of the router and check if you get answers from the router.

  Open the Internet browser and in the address bar type http://192.168.1.1. See if you can open the router configuration page.

  If this does not work then you can try to update the official firmware on the router using the TFTP.exe file.

  Disable the firewall on your computer. Connect the computer to the router with the Ethernet cable.

  (1) download the official firmware file from the site Web of Linksys router. Save it to your computer.

  (2) download the tftp site Web of Linksys. Follow this link to search for the file tftp. You'll find downloads for router BEFW11S4. Select the version 3.2 hardware and download the installation wizard. Save it to your computer.

  (3) run the installation wizard. In the server box, type the IP address of your router. In the password box, type the password of the router. Default password for the router is admin. Find the file of the official firmware you have already downloaded and click on upgrade.

  See if it works.

  After upgrading the Firmware on the router, it is recommended that you must reset the router and reconfigure.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 10 seconds. Power cycle the router and reconfigure.

• Want 5660: Printer cannot connect to the router

  All of a sudden the printer can no longer connect wireless to the router. Printer router ok may be defective

  Please provide the following information if anyone can help including:

  The printer model - done

  Operating system of the computer-

  Detailed - description of problem including all devices network (extensor, switches)

  Connection method - Direct wireless, wireless, wired LAN, USB? -

  Number of brand and model of router and modem? -

  Error messages - on the screen of the printer or computer, no matter what flashing light patterns? –

  The printer is connected directly to the wall outlet?  If this isn't the case, please explain how the power is connected.

  Do you think the printer is going to sleep and can't wake up? -

  If wireless, in the event of problem, what is the status of the blue wireless light on the printer, active, disabled or flashing? –

  Power off the printer and the router.  Power on the router and wait 3 minutes, power on the printer.  It connects to the router now?  What is the IP address of printers?

• Cannot connect to the router efax. On HP Officejet 650010n, Windows XP desktop, routher: tp-link

  I tried to connect the router to home port to efax.  Having hard time understanding connection.  Don't know which network in the list I'm suppose to connect to match the router password.

  The network you should be interested will generally be the first listed item.  By following the previous steps, you can check this on your computer.

  As Super-Dave pointed out, however, this printer has a built-in for eFax support.

  To use eFax with this printer, you synchronize your eFax account with your email and print faxes that you receive as attachments to email like you would for any other file.

• WRT600N still cannot connect to the router after factory reset

  OK, so I reset the router but I can not yet connect to installation using the password factory (admin/admin) (white/admin) (admin/empty).   Now, I have a network encrypted and without access to the configuration... I even tried to use the installation CD, but it does not recognize the router.   Anyone have this problem or know of a possible fix?

  Thank you, Carl

  Hey try resetting the reset button of the router in a way to equip
  light flashes on the router & then make a full of electric network
  cycle that is, unplug the power to the modem & router cables

  & then connect the power supply to the modem first once all the lights are
  Green, you can plug the power cable to the router & discover
  This will definitely work!

• Cannot connect to the Web Interface using IE9 idrac6

  Hello world

  I was appalled last Saturday when I have downloaded voluntarily a remote server knowing that I would use the idrac to bring up, to see that when I tried to connect to the idrac he wouldn't my password.  I had to call the customer and send them to the site on Saturday night and I was very angry about this.

  After being, upward, that I tried several times to connect remotely and it still would not accept my password, I tried the reset of the OM Server page, but not to go.  I would put my password and it should Flash quickly "Access please wait" at the bottom of the screen, and then he would just go back to the login screen.

  I thought maybe it was a browser security issue, so I tried to add the remote site to my trusted sites and lowering of safety, but it did not help, so I tried various is to say like compatibility mode settings and still no go.  This has been tried on 2 different machines to Windows 7 with IE9, a x 64 and x 32.  Then I thought that I would try Chrome instead and it worked fine...

  So I tried a VM XP with IE8 on it, and it worked well.  It seems so - that IE9 is the culprit.

  I called in the systems management team and we tried which helps some ActiveX controls in the zone of confidence, but it did not help and he me basically what IE9 doesn't play well with the drac's and they are working on an update to fix the problem.

  This is perfect and I accept it, because I know I can get with another browser if I had to, but someone has actually managed to make it work with IE9?

  I have the same problem. But, I have found that if 'Remove' all under 'Browser history' (check everything: Cookies, history, temporary Internet files, etc...) it will allow me to connect and work for a while. Then I after a bit, it stops working. So again, I delete all log and work harder. This was a major pain in the rear lower.

  Oh, but I never have the ActiveX/native console to work. But I'm just using the Java plug-in.

• See Express Core cannot connect to the router UCM IM & P. XMPP: inactive

  I'll put up a teleconference environment (10.5 CUCM/IMP) with a few G2 MX300, SX20 and many Jabber clients. The solution is the new Express Core/Edge.

  It seems that I can't seem to make the core of the highway to connect to Unified Communications and more specifically with my presence and IM UCM environment. Everything is correctly configured in the Configuration > Unified Communications section. I see that the connection to the AAU itself is active but not at UCM MI of the P & I see the error "router XMPP: inactive.

  Each server name can be resolved by DNS, so there is no problem with that. Channel Express is in the same subnet (switch) with the AAU and AAU IM & P. passwords are configured corretly. There is not enable encryption between UCM IM & P and the core of the highway.

  Am I missing something? What I have to do additional configuration for the side IM & P? Can someone help me? I enclose some screenshots of my environment.

  Thank you, Stefanos

  Hi stavropouloss,

  So that the service becomes active, you will need to have the area between Highway C & E active.

  To have C & E traversal Expressway area active you should download on each server certificate signed by a trusted CA authority.

  Documentation on how to generate can be found here: http://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/expressway/config...

  At soon buddy.

• Pavilion HPE h8z cannot connect to the router to 1000Mb

  Pavilion HPE h8z

  Windows 7 (all updates including updated network driver)

  Router: RV220W Cisco

  Cable: Cat 6

  Any new system.  All the network settings on the PC and the router are "out of the box '.  The system will not connect to 1000 Mb (Gigabit), even if the other 2 on the same router (1 XP, Linux 1) connect without any problems.  Swapped cable and ports without difference,

  And before anyone asks, it that a Realteck Gigabit Ethernet chip on the motherboard.

  Tech came out at 08:00 as expected.  Replaced motherboard.  We have video, we have Gigabit Ethernet.

  HP should really look at this whole incident.  In addition to taking almost 4 weeks to fix the problem and let the client without computer running for more than 10 days, this event has cost thousands of dollars support HP.

  Process of elimination said that it was a hardware problem. IMHO, this kind of problem should have been taken before his departure from the factory (certainly not a HP has / operates the plant).

  If HP has spend this amount of resources to solve this kind of problem, it is not surprising that they want to get out of the PC business.

• Cannot connect to the administrator account because the password is not valid

  Original title: I HAVE VISTA... ALL OF A SUDDEN FOR A DAY, I TRIED TO LOG INTO MY ADMIN PAGE AND MY PASSWORD IS NO LONGER VALID HOW TO RETURN TO THE PAGE OF MY ADMIN WITH ALL MY MUSIC PROGRAMS, ETC.?

  I tried to connect to my admin page and it will not allow my password... helllppp!

  Hi donfamous,
   
  Follow the steps listed in the article given below to resolve this issue:
  What to do if you forget your Windows password
   
  Additional reference on:
  The Windows password problems
   
  Note: Microsoft technical support engineers cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features.
  For more information, see:
  Microsoft's strategy concerning lost or forgotten passwords

• your computer cannot connect to the remote computer because the Office gateway servers Remote certificate has expired or has been revoked

  Hi guys,.

  Im getting this error or on a server I don't have physical access to, how can I get this client of the RPD to ignore this error?

  Hello

  Please ask your question in the forums TechNet for assistance:

  https://social.technet.Microsoft.com/forums/en-us/home?Forum=winserverTS

• IE 8 cannot connect to the web site because of restrictions on computer

  By clicking on a link Web translates into a negative answer above.

  The first Question of troubleshooting: If the problem is new, what has changed between the time things worked and the time they do not have?

  The second issue of Windows troubleshooting: what is the status of virus/malware of the machine? If you think it's clean, what programs (and versions) allows you to determine this?

  Make sure that the computer is clean:
  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  Post back with answers/results for additional assistance if necessary. MS - MVP - Elephant Boy computers - don't panic!

• Lexmark printer will not connect to the router

  Original title: HELP

  I switched to Fios and now have a new modem/router and I don't know how to get my Lexmark printer to recognize. How can I solve this problem?

  Hello

  Thanks for posting the question in the Microsoft Community!

  The Lexmark printer will not connect to the router/modem.

  Because the problem is with the Lexmark printer cannot connect to the router, I suggest contact you the Lexmark support team in order to get help with this question.

  You can try to get help on the site:

  http://support.Lexmark.com/index?page=productSelection&channel=supportAndDownloads&locale=en&UserLocale=en_US

  If you need any help or if you encounter problems with Windows in the future, let us know and we would be happy to help you.

• Your computer cannot connect to the remote computer

  Hello

  OT:

  Your computer cannot connect to the remote computer because the remote desktop gateway server address request and the certificate subject name do not match. Contact your network administrator.

  I implement the remote desktop session based on Win Server R2 2012.

  I create a free sign for certificate certificate and also install the certificate to the client computer.

  But when I click on any application it shows me error.

  

  Hello

  You may need to ask the question on the TechNet forums. Please post the question here:

  https://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

  Kind regards