Cannot disable the flaws of the WSF

Recently, I added two B200 M2 blades to add to the existing three B200 M1 blade. My previous firmware was 1.2.3l and therefore discovery has failed on two M2s. yesterday, we went to 1.4.3q and the M2s discovered correctly and everything went well. Except that I can't erase two original vulnerabilities for WSF: didn't even if they went through a full discovery.

What can I do? I know it's just an annoyance, but for me it's a great nuisance. Someone has suggested their retirement by moving elsewhere in the frame and create a new service profile, but it would be a last resort. Looks like this must be something easier than that...

The photos show the affected sites were 1/5 and 1/6.  When the B200M2 were discovered with success, they were in these slots, or other locations.

If there are in different locations, removed a PIN from the production, turn off the blade, the blade to 1/5, check out blade, discommission blade, repeat 1/6, back blade recommission and place of production.

Worst case, you can downgrade/recommission the chassis.

HTH,

Responsible Dan

Tags: Cisco DataCenter

Similar Questions

  • Cannot disable the hidden administrator account

    Am running Windows 7 Home Premium. I activated the hidden administrator account and renames and added a password via an elevated command prompt. Now using the same elevated command prompt cannot disable the account. Error name is not found.

    What is the exact command that allows you to disable the account?

    What account names you see when you type this command:
    net users
  • Cannot disable the CS6.  Have disabled successfully recently because of computer problems.  Is there a limit to the time that you can disable?

    Cannot disable the CS6.  Have disabled successfully recently because of computer problems.  Is there a limit to the time that you can disable?

    Hello

    I think to delete the content in the files SLCache and SLStore files should work for this.

    Concerning

    Jitendra

  • Cannot disable the microphone 1 on SX10 TC7.2.0

    Morning!

    Here, we have a SX10 recently upgraded to TC7.2.0, both microphones work perfectly but the problem we have is we cannot cut the microphone 1 (one internal), we need mute because the codec is somewhat less a screen with speakers to the codec.

    I tried to mute to ' Configuration > system setup > Audio > Microphone Mode 1 input > Off "but not working even after a reboot of the device.

    I tried to disable it in CLI with the command ' xconfiguration Audio input Microphone Mode: Off "but doesn't.

    Can someone give me a hand with this problem?

    Best regards and thanks for your help.

    Hello - I just tested this with free TC7.2.0 software.  The version number is TC7.2.0.aea6651.

    I tested during a call and used the web interface to Configuration > System Configuration > Audio > input Microphone 1 Mode > Off

    I tested it with a table 20 Mic and without.  In both cases, the internal mic has been disabled successfully by the interface web and delivered to market successfully.

    To check this, I typed the two microphones with my fingernail.  The location of the internal MIC is just to the lower right of the camera that you look at the front the SX10. It shares the location with the infrared sensor.

    I could easily hear the tapping of my nail through the speakers of the other system I was calling.  Disable "Microphone Mode 1:" and I couldn't hear the tapping.  Turn on "Microphone Mode 1:" and I could hear the tapping very well.

    So I think that it works correctly.

  • HP Z620: Cannot disable the legacy in Bios boot media

    Hello

    I installed WIndows 10 using UEFI, but could not disable the startup mode of the legacy support in the BIOS.

    If I disable Legacy support PC 6 beeps and flashes of Red led on the power button.

    I don't know if someone has encountered this problem before or have a solution for this?

    Help please!

    See you soon

    Just find the answer to my own question.

    This is the VGA card that is the problem. It's not about UEFI.

    After Exchange with a newer VGA card I can now turn off the boot of Legacy media.

  • Where is the "selection of tools on the homepage - cannot disable the pop-up blocker.

    Pandora website says disable the popup - blocker to proceed - unable to find the 'Tools' option on the Foxfire toolbar first disable Blocker?

    Press F10, or press the Alt key to bring up the 'Menu Bar' temporarily.

  • Tecra A10-13 a - cannot disable the touchpad more

    Dear users,

    I hope that the question was not mailed before.

    Symbol of the touch and the launch is is more shown in the taskbar at the bottom of the screen. FN + F9 works to disable the touchpad.
    What verification Toshiba via programs, utility, the utility touchpad is no longer there (perhaps cc-cleaner has erased).
    How can I reinstall this feature or turn off my touchpad? I can't find it in the control panel or the other.

    Thanks in advance

    Michael

    Hello

    I agree with you: probably the driver for the touchpad has been cleared

    But there s no problem because you can download it from the official website of Toshiba:
    http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

    After installing the touchpad driver symbol in the taskbar should reappear and you should be able to turn off once again.

  • HP Pavilion 17-e-116dx - cannot disable the touchpad

    Operating Windows 8.1.  I'm trying to disable the touchpad on the computer I just bought.  I normally use an external mouse, but even without that, the touchpad is uncomfortable when I type, causing the paper up and down on the screen.  I understand the touchpad doesn't have the feature of plays twice in the corner to turn it off, but there must be a way to avoid having my documents move wherever.   Is badly in need of help!

    dmwvols,

    Welcome to the HP Forum.

    See if anything here helps:

    Control Panel > display icon > mouse > properties > TouchPad tab / ClickPad parameters

    Dragon documents:

    Reduce the sensitivity of the TouchPad

    Click on the Thumbs - Up Kudos to show that you appreciate the help and time of our Experts.

    Click on accept as Solution when the answer is a good solution or workaround!

    Although I strive to reflect best practices of HP, I do not work for HP.

  • Dell Inspiron 15R cannot disable the touchpad

    Hi all

    because this model does not detect function of palm that eliminate palm accidentally trigger the touchpad, I looked for ways to disable the touchpad.

    http://Forum.NotebookReview.com/Dell-Inspiron-Dell-Studio/567926-how-disable-touchpad.html

    link above may not help me.

    your help is very appreciated.

    Hi JamesyMY,

    It seems that the problem is with the utility of rapid setting due to which + or does not work. You can install the utility of rapid adjustment from the link: http://dell.to/Zl7Oz3.

    You can also update the touchpad drivers, please see the link: http://dell.to/10wz2Ow.

    Keep me posted with the results. I'll be happy to help you.

  • cannot disable the nod on occasion? 10.1.1

    In iMovie 10.1.1 I can't disable snap to mark? I checked the other questions and it doesn't seem to work.

    Have you tried to disable alignment in the view menu?  Make sure it is not checked.  This applies to all the slam.  I don't think you can disable just for the brands.

    Geoff.

  • DV7-6143eo cannot disable the keyboard driver

    Hello

    A time, that I had a problem with some keys on my keyboard, repeating endlessly as if the button was pressed, even if the current button does not seem to be stuck. He would usually stop repeating after pressing the key. I had a similar experience with another laptop and it ended up repeating constantly the key even after pressing the key.

    Until I'm in a similar situation with this laptop, I decided to get a usb keyboard. It worked for several months, but suddenly the issue with a key constantly repeat even after the key on the keyboard of the notebook appeared.

    As a temporary solution, I turned off the key 'w '. Try to delete the driver for the laptop keyboard simply result in it to be reinstalled on reboot. It seems that my only option is to disassemble the laptop and remove it or the deactivation of the pilot.

    I have no experience with the dismantling of a laptop and would like to avoid this. If I go into Device Manager, a disable option does not display the drop down menu to the pilot and in the properties of the option is grayed out.

    The laptop is a dv7 6143eo and use windows 7 64-bit. The name of the driver is "Standard PS/2-keyboard" (keyboard = keyboard).

    Sorry for the double posting, but I felt it deserved its own post.

    I managed to finally find a solution. If it is not as elegant as I had hoped, it seems to work.

    1. open Devicemanager.

    2. right click on the keyboard driver for laptop computer-> select "Update Driversoftware".

    3. Select "browse the computor for driversoftware.

    4. choose "Let Me pick from a list of devices on the computor.

    5. click on "view the material compatibel.

    6 find a driver that is not compatible with your laptop, I personally went with 'Toshiba - Toshiba USB 109-keyboard Japanase'. Click Next.

    7. click 'OK' in implementing cautioned, we want something that is not compatible after all.

    8. it should tell you that the driver has been installed and ask if you want to restart.

    After restarting your laptop keyboard should work now not at all, including the boring repeated key.

    With my limited knowledge, I can't guarantee that this will not be some issues (can't think of everything well), so do it at your own risk.

    I hope this will help others and post here will make it easier for others to find the 'solution' timetable, that I had to spend.

  • Cannot disable the reorganization of desktop on Windows XP icons

    I'm having a problem with the auto arrange feature that automatically organizes the icons on the desktop whenever I restart my computer it self organizes icons. I do not have the option selected when I click right/rearrange the icons by / auto arrange also lock web items on desktop is disabled.

    I am able to rearrange my icons after I am starting up, but whenever I restart it rearrange my icons.

    After checking several forums seems whether an error in Windows XP and that the solution is to create a new user profile and start from scrach.

    Any ideas?, thanks.

    No, no changes that could cause this problem, I tried 2 methods without success, but here is the solution:

    1. data of the user backup (My Documents, Favorites, desktop)

    2 remove the user profile

    3. connect you again with this user to create new user profile

    4 restore the user data

    And voila! Automatic reorganization works as it should once more!

    Hope this help others causes this problem on internet research will take you to several non-functional solutions.

    Thank you!

  • Cannot disable the Premiere Pro CS6

    I am trying to disable Premiere Pro CS6, but the option in the menu "help" to disable is grayed out. I did all the updates to the first. Any help is appreciated. Thank you!

    If it has been activated?

  • Cannot disable the CS6.

    Hello

    Using a MacPro - try to disable my account before I sell it. When I type 'disable' I get the error "Deactivate failed, please try again." Really don't know what to do. Help please.

    Thank you.

    Hello

    Please refer to the link given: https://helpx.adobe.com/x-productkb/policy-pricing/activation-deactivation-help.html

    It will be useful.

    Concerning

    Bianka Attre

  • Cannot DISABLE the speakers of an HP Pavilion Entertainment PC

    Greetings! I recently downloaded updates for the computer. Now, my speakers and the headphones does not work. I have an amber mute button that turns it on my screen on the upper left side of my keyboard. I can't activate this button. I don't have a system restore point which will allow me to restore the system to a working state before recently downloaded updates have been installed. I tried to restore the default values for my speakers. Does anyone have any suggestions? I am logged in as administrator. Help, please! Best regards, Stewart

    Greetings BHK6! I discovered the solution to the problem. I restored the ORIGINAL AUDIO DRIVER. The function of speakers now. My question came on 27 December 2013 when I allowed a useless update. I went several days without the sound on my computer, and I am grateful to have the restored sound. I should have tried this solution to restore the ORIGINAL AUDIO DRIVERS several days ago. Thanks for your help. Blessings, Stewart

Maybe you are looking for