Cannot install anything but XP after memory upgrade

Similar Questions

• Cannot install flash player. After you download the Adobe FLash Player installer and running, a gray pop-up window opens but nothing does not appear in it. There is no progress bar or whatever it is.

  Cannot install flash player. After you download the Adobe FLash Player installer and running, a gray pop-up window opens but nothing does not appear in it. There is no progress bar or whatever it is, and even after keeping it running for a long time, there is no progress. Please help with this question.

  Hi Rlap,

  We are aware of this problem and are working on a fix.  In the meantime, please use the offline installation program, displayed at the bottom of the help page corresponding to your operating system and browser:

  • Installation problems | Flash Player | Windows
  • Installation problems | Flash Player | Mac

  Installers are at the bottom of the page, in the section "problems".

  --

  Maria

• HP Photosmart C6280: cannot print on C6280 wireless after the upgrade to Windows 10

  Cannot print on C6280 wireless after the upgrade to Windows 10. Have removed the device, but try to re install the printer when is not found. Can print if I connect USB. Tried to reload the driver using HP Support software help, but when he arrives at the end of the download fails.

  Hi @Ron9871,

  Welcome to the Forums of HP Support!

  I see that you are unable to get your printer HP Photosmart C6280 wireless printing. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I would like to try the steps in this guide, "offline" Status Message printer (Windows 10).

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  • Print a Page of Network Configuration menu of the printer front panel. Note: the IPV4 IP.
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.

  Please restart the router, the printer and the computer in this sequence.

  If you're still having problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  • Use the File Checker system to repair missing or corrupted system files. It's always a good idea to back up your data before proceeding.
  • File system check (SFC) analysis and repair system files & DISM to fix things that are not SFC.

  You can try to change your WSD printer port by a Standard TCP/IP port.

  To do this, you will need your current IP address printers.  The Network Setup page shows the parameters of network for the product. To print this page; Press the button of network () on the control panel of the product.

   

• Impossible to get updates of Windows to work and cannot install anything after upgrading to SP3

  After the upgrade to SP3 I met many problems. Any time I go to install it I get a Windows Installer error is not installed (even if this is the case) and I have to go to start/run and type Services.msc and the go to the installer of windows and right-click on it and select start and then install what I was tring to do.  Windows Update will not update and I tried to restart the installer and it does not work.  I tried the auto fixes but cannot get them to work because they will not install either or will not run.  I had to uninstall Windows Defender as I am unable to update the definitions it is basically useless.  All this started after I did a full cleaning of the computer and then downloaded the original Windows XP that I bought from Dell.

  Try this:

  http://www.ehow.com/how_7176381_microsoft-install-after-installing-SP3.html

  I hope this helps.

• cannot start win8 after memory upgrade

  Hi I have a HP Pavilion P6813w

  It came with win 7 64 bit installed with 6 GB of ram
  I created a duel with victory 8 boot
  It was working fine until I got my 16 GB of ram today
  Well I got the 16 GB in and turn on the computer to get to this
  Recovery
  your pc needs to be repaired
  the application or the operating system could not
  be loaded because a required file is missing or
  contains errors.
  file:\Windows\system32\winload.exe
  error code 0 xC0000001
  but when I'm out of 8 GB it starts and displays the 8 gb of ram.
  I tried to do the repair installation dvd options since the win8 and even tried it recover usb option
  When I use the usb option I get error 22 grub 1.5
  so my question is why win8 will not load with additional memory
  and even win 7 does not load
  It gives me the same error
  my computer shows he takes supporting up to 16 GB
  4 GB ram sticks
  IM experience pc users and cela just stem me
  any idea what could be the problem

  Hi Wallace,

  There is a limit of memory for Windows 8. For version 512 GB for 64 - bit and 32-bit maximum 4 GB is allowed.

  For more information, see the links.

  Limits of memory for Windows versions 

  The memory upgrade (RAM): HP Pavilion p6813w Desktop PC support

  If you have any questions on Windows, feel free to let us know. We are happy to be of assistance.

• Y430A can not boot after memory upgrade

  OS: VISTA HOME PREMIUM 32-BIT
  CPU: P7350
  MEMORY: HYNIX DDR2 667 2GB

  I added a 2 GB Kingston ram on the connector 2

  First of all, it can be the start and connect to windows,

  but after a while, the system of suspension or the SCREEN BLUE DEAD shows,
  He cannot even get into the bios screen when I reboot it

  but it can be boot up if I remove and reconnect the memory

  Sometimes the machine can be restarted and works correctly, except if once I turn it off

  I tried to exchange the slot 1 and 2 with 2 x 2 GB,

  and also replace with 2 x 256 MB Hynix memory.

  but it does not work.

  The new memory is not faulty or is not compatible because it works very well if it autonomous.

  In short, if I install 2 x 2 GB memory, the system may start only once.

  Is it the BIOS problem or it's my mistake?

  Please help and sorry for my bad English.

  Thanks in advance.

  This is perhaps due to the incompatibility of the modules of RAM, working together. If Yes, than to change only the modules will help.

  Also looks like Y510 behavior when it was a fresh model - Y510 all were not able to manage two RAM modules. Update the BIOS helped. For now no new BIOS for Y530/Y430, so will have to wait.

• Error 1723 - cannot install anything with a .msi installer

  I understand that this kind of question has been asked several times on this here that I searched, however still have not been able to solve the problem :(

  Basically, I'm unable to install anything with .msi (windows package install), I get the error messages like:
  "There is a problem with this windows package install." A DLL required for this install to complete could not be run. Contact your provider to support personal or package"
  OR
  "Installation directory must be on a local hard drive" (even if this is the case).
  It is not with a specific software, I have a problem with. For example I tried to install Acrobat, Quicktime, rhinoceros (3d software) and T-splines (plugin for Rhinoceros)... which was a mistake and had some msi installers, so I think its safe to assume this is not not the software, but a problem with my computer, and I suspect the registry eventually.
  Things I've tried so far without success
  • sfc/scannow
  • Microsoft fix it tool
  • Checked the status of windows install services (it was in operation)

  The only thing that I came close to using 'run as administrator' with quicktime as it was the only program which enabled this option as an msi file. This actually worked and was able to replace the DLL error somehow and install quicktime.
  Any help is really appreciated, I hope that his is not going to use a new installation on win 7 :(

  None of the above worked, unfortunately, but don't worry...

  ... I FIXED IT
  Here's how
  I resorted to a repair of windows 7 by using the support of instillation DVD/ISO/USB of my version on win 7 (it is actually an upgrade, wait for your upgrade to the exact version even though it should work with your key)
  I followed these instructions to the repair facility
  http://www.SevenForums.com/tutorials/3413-repair-install.html
  Don't worry, you won't lose any files, but I would still recommend making a return to the top.
  I use Macrium reflect free http://www.macrium.com/reflectfree.aspx
  OR you can simply backup your stuff important to usb. But like I said, you shouldn't lose anything, and all programs will be installed as well.
  If you do not know your key (for when he asks during the upgrade) Windows use magical jelly bean before starting the upgrade and take notehttp://download.cnet.com/Magical-Jelly-Bean-Keyfinder/3000-18487_4-10079600.html keyfinder
  NOTE: After you completed the upgrade and to my office, I was greeted with the notification

  "Setup has detected that .NET Framework 4 needs to be repaired. Do not restart your computer until the repair is completed. »

  It is perhaps was necessary to repair? I don't know, but it took about 10-15 mins to fix it for me.
  Anyway, the bottom line is, so far, everything works well again, I can install msi without problem, I will report back if I get more specific questions, but fingers crossed I don't want.

• Cannot create a PDF file after the upgrades: Adobe 9.2 and Mac OS 10.6.2

  After the upgrade to Adobe Professional 9.2 and Mac 10.6.2 I lost the ability to create PDF files.

  The printer Adobe (display says that the printer is v. 9.0) indicates the status of the job as "Mistake" and has the following message; "You must install the software to use this printer. To install the software, choose software update from the Apple menu. If the software for your printer is not available in software update, contact the manufacturer of your printer. »

  I get errors when I try to create a PDF from a Web page.

  I get the following error when I try to create a pdf from a word file: "Acrobat cannot open 'AAA.docx' because it is not a type of supported file or because the file has been damaged (for example, it was sent as an attachment to e-mail and has not been correctly decoded).

  To create an Adobe PDF document, go to the source application. Then print the document in Adobe PDF format".

  (I can create a PDF from jpg files... but I never really have a need to do this...)

  I uninstalled Adobe Professional by using the uninstall program (then emptied the trash and restart), then reinstalled Adobe Professional from disk (and restarted).  After the reinstallation, I always get the same problems, even if I get no error message until Adobe Professional updates from 9.0 to 9.2.  Before the upgrade Adobe, v9.0 attempts to print to pdf just act as the pdf is created (no error message), but I do not get a backup fast, nor is a new pdf no matter where the document is located.

  Help, please!

  With OSX.6.x, the possibility of using the Adobe PDF printer has been lost. See the ad at the top of this forum (known issues with Snow Leopard).

• Satellite P100-219: overheating after memory upgrade

  Hello guys,.

  I've recently upgraded to 4 GB RAM in my laptop, and he did it again.
  Computer laptop stops immediately after awhile. CPU or GPU gets really hot. Works fan CPU, GPU was not used intensely. Simple web browsing/cat/emailing.

  What becomes hot however is part to the left of the memory/wlan compartment. Is it possible that a chipset gets hot after just upgrade memory?
  I tested the memory with Memtest + for more than 3 hours. No errors.

  Moreover, the last time that my phone was in ASP it had returned with DMI saying it's Satellite L20! I dunno if that could be related...

  Thanks in advance for your suggestions,
  mentorek

  You have blown the dust anyway? As you say, maybe another component is overheating rather than the CPU or GPU. The CPU/GPU heatsink can be shared with other chips.

  Have you installed RAM high performance? His best choose RAM that has the same Timings CASE/RAS as the original factory of RAM.

  The name DMI does not cause something like this.

  PS. If you're running Vista, you must pass the BIOS and driver nVidia on the Toshiba site

• Cannot install anything.

  My Xoom of US - not all of a sudden doesn't let me install anything from the Android Market.

  I've selected an application, and click on install, I saw a notification skipped upward, bottom right indicating 'Installation', but after a few moments,

  He showed "Appname installation fails.

  I tried to restart my Xoom and clear the cache of the market, but still no luck. Someone has encountered this problem before and how do you solve?

  Ok.. It is the problem of storage space...

  I left 3.95 GB. It's Go, gigabytes left, but it won't let me install anything... I think that I had deleted about 1 GB and then have 5 GB left... then my Xoom behaves normally.

• Cannot enter 'log-in' page after the upgrade of VISTA SP1 x 32 SP2 with failure code 0xc0190036 340/47122 (explorer.exe)

  I was "forced" to upgrade my computer to SP1 to SP2 when I tried to download the latest msn who.

  The upgrade part wasn't serious and VISTA asked me to restart my computer after the upgrade. Then I REBOOTED.

  The problem came when the final stages of the upgrade, which took part after reboot. It was somewhere near STADIUM 1/3 or 2/3 and then suddenly all blackened. I'm POSITIVEMENT SAFE that my computer is connected to the power supply (mine is a laptop). And then when I start to restart my computer (the second time), I got this message

  0xc0190036 340/47122 (explorer.exe)

  Then I restarted and I got to a page where windows told me that my computer is not able to be marketed with success because of the recent changes I made.

  I did an upgrade from the night before, where I update the OFFICE GENIOUS sthsth (sorry, but I forgot the name). I need to upgrade this thing in order to be able to upgrade to SP2 (complicated huh? lol)

  I tried to use the recovery thing and save the thing but WINDOWS insisted that I do not have a recovery... I would say is quite disappointing...

  COMPUTER:

  HP 2133 NetBook

  VISTA HOME BASIC run x 32

  I ' ve done some searching on the web but found nth related code 340/47122 and VISTA HOME BASIC x 32 and SP2...»

  The last method I want to use is the method of parameters factory reboot, restore... so here I am, ask help from experienced users. I don't have any DVD or CD ROM for the restart or what. any method that can safe me to restart my computer?

  Million thanks,

  momikoo :)

  Hello

  Method 1:

  I suggest you to check if you are able to start in safe mode or last known good configuration. Follow the steps mentioned below.

  a. restart the system and keep tapping F8 until you reach the start menu.

  b. Select secure known mode/last good configuration in the list and press ENTER.

  Method 2:

  I suggest you follow the steps mentioned in the link given below and let us know if your problem is solved.

  Error code on a black screen when you try to install a Service Pack in Windows Vista: "0xc0190036."

  http://support.Microsoft.com/kb/975430

   

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Cannot install Service Pack 1 after 4 years, Windows Vista Factory restore

  I have a Dell XPS ONE and used the option to restore to the factory due to several problems. The system is 4 years old and maintain a 4 year old Windows Vista Home Premium system proved to be too much for me to handle.

  When I try to update Windows, I managed about 60 updates, but then I get to the SP 1. He tells me that it is installed, but then I go to the update again and it tells me that I need SP I... I can go through the same indefinitely, SP 1 installation, but he always tells me that I need to install Service Pack 1 even if it was just installed successfully. Aparently, SP 1 is not installed correctly, but it tells me that it is installed. It is not!

  In the meantime, I can ' t reinstall Norton Internet Security. He tells me that I need SP2 for Vista.

  I have a Dell XPS ONE and used the option to restore to the factory due to several problems. The system is 4 years old and maintain a 4 year old Windows Vista Home Premium system proved to be too much for me to handle.

  When I try to update Windows, I managed about 60 updates, but then I get to the SP 1. He tells me that it is installed, but then I go to the update again and it tells me that I need SP I... I can go through the same indefinitely, SP 1 installation, but he always tells me that I need to install Service Pack 1 even if it was just installed successfully. Aparently, SP 1 is not installed correctly, but it tells me that it is installed. It is not!

  In the meantime, I can ' t reinstall Norton Internet Security. He tells me that I need SP2 for Vista.

  It is good, that you can not install Norton Product.  Stop trying.  No McAfee either.
   
  Avast, AVG, Avira , or UnThreat are choices fine (free option).
  You could spend ~ 60USD during two years of eSET NOD32 AntiVirus (not more - just product AntiVirus) and which would be more worthwhile.

  Regarding SP1 - do this manually.  Windows Vista Edition _, _ - bit? [Fill in the blanks]

  Download and save the SP1 that is appropriate for your architecture of Vista (32-bit or 64-bit) operating system (on your desktop).  Reboot and logon.  Right click on the saved file and choose Run as administrator.  Follow through until it's done and restart with 5 minutes between each restart twice.

  • Windows Vista 32 - bit SP1
  • Windows Vista 64 - bit SP1

  Download and save the SP2 appropriate for your architecture of Vista (32-bit or 64-bit) operating system (on your desktop).  Reboot and logon.  Right click on the saved file and choose Run as administrator.  Follow through until it's done and restart with 5 minutes between each restart twice.

  • Windows Vista 32-bit SP2
  • Windows Vista 64 - bit SP2

  Then download updates post-SP2 via normal means.

• How can I fix mini slow mac after memory upgrade from 4 GB to 16 GB

  I have a Mac Mini (ver 6.2 end 2012, i7 to 2.3 GHz, OS X 10.10.5) that I just put new memory to upgrade to 4 GB 15 GB (Crucial 16 GB = 8GBx2 kit corresponding blades plug their scanner software and HW Apple specs). I use HDMI to my Vizio 32 inch HDTV and now my Mac runs slower for typing, clicks, etc, but the software seems to work fime. I have checjed the "about this Mac" and it shows the memory is available and authorized to use. I also run app "Cleaner" memory and it shows the total memory available and currently in use.

  Then what should I do to solve the slow?

  Thank you in advance fr that all help someone of you provide.

  Ron/Nightstyles

  I run a mini end 2012 with 16 GB.  It's fast... I also have SSD which also provides the spectacular for startup performance improvement and any disk activity.

  Have you checked for any process out of control by using the activity monitor?

  https://discussions.Apple.com/message/20379601#20379601#20379601

  Have you reset the NVRAM and SMC memory since installing the RAM?

  Restart and hold down the command-Option-P-R keys immediately after you hear the startup sound.

  How to reset the NVRAM on your Mac - Apple Support

  To reset the SMC?

  Basically the kindly stop and turn off the power for 10 to 20 seconds.

  Reset the management system (SCM) controller on your Mac - Apple Support

  After resetting these go check the keyboard settings in system preferences...

• NB100 black screen after memory upgrade

  My NB100 works well with the Samsung 1 GB of memory which was included when I bought it, but when I replaced the screen with a new Kingston 2 GB 667 MHz (2 G/VR667D2S5) doesn't show anything when I turn on the laptop back, even if the LED indicators seem normal and fans inside its normal.

  I tried a replacement memory (same type of Kingston) - still no luck. I put the old Samsung back and the laptop starts fine.

  Any ideas?

  Hey Buddy,

  What NB100 you have exactly? What is the number of exact part of it?

  AFAIK NB100 supports only 2 GB of RAM. This means that you can install the module of 1 GB in each slot, but not a 2 GB RAM module will not work.

  So, if you want only 2 GB of RAM, you will need to purchase an additional 1 GB module because the NB has two memory slots.

• Pavilion 15-ab043sa: cannot reset to factory settings after the upgrade computer laptop brand new 10 Windows

  I bought 2 new laptops, they seem to be special models not listed is not in the HP support site, purchased from Currys PC World in the United Kingdom.

  First HP Pavilion 15-ab045sa laptop computer 15.6 "-red, upgraded to windows 10 perfectly well and I made a backup of the system while I studied the creation of recovery media (this info must be printed with the laptop in the box, rather than letting the user have to find BTW)."

  The other a HP Pavilion 15-ab043sa laptop computer 15.6 "-blue, for my parents, has turned into a total disaster."

  The two models are the same, except that the first is red and the other is blue, that's why they have different product numbers?

  I was now in a position where the recovery on the D: drive partition is not a factory reset.

  I did not even recovery disks as having the first one to go smoothly, I thought the same thing would happen on the second laptop and I got the recovery disc then.   I tried to create a USB stick recovery, but I had no one who can save the system settings - need at least 32 GB free.

  This occurred as first I started the laptop, made of windows, MS Office 365 updates, added then waiting 2 days for windows 10 to arrive.  When it came it installed fine and then I added a printer driver for an HP printer and made some configurations of the operating system.  At the next reboot showed something was wrong as the boot took over 7 minutes.  As the synaptics app was referenced twice in the tab start Task Manager also had strange things in the system.  Rather than go back to a previous system restore point that I attempted to identify what was wrong and uninstalled all without success.  I then had the opportunity to go back to 8.1 for Windows or "reset the PC.  Not a lot of explanation on delivery to zero and certainly no warning options that the D: partition was no longer valid.  Windows options were "in my face" so I don't think watching HP recovery.  So I chose to run from Control Panel 'Reset the PC and keep the files'.  So, indeed, I now have a clean install of Windows 10 but have lost all applications that were on the factory orginal building.  I see no way to re - install all of these programs and find the license keys.  I have more HP recovery at all.

  So I have no way to put the blue doesn't return to the factory settings.

  Advice please, I want a laptop blue, the same as the red, i.e. Windows 10 with all applications that have come to the factory as well as the correct printer drivers and a time of less than 30 seconds of starting.

  You are not sure if there is anything I can copy from red to blue to get it going again?

  Any help gratefully appreciated, thank you

  You have the options of Chat or telephone. Mon - Fri 08:30 - 18:00. Sat 10:00 - 16:00.

  https://support.HP.com/GB-en/contact-HP/product/HP-Pavilion-15-ab000-notebook-PC-series/7771366/model/8255007#Z7_3054ICK0KGTE30AQO5O3KA30F3