Cannot start my Satellite A100 - 1 G - the battery light just flashes

I have a laptop A100 - 1 G. Indicator of battery showed low and I plugged the power supply for the laptop and he showed the connection was made, later she flashed low battery connect to the power (although it was still connected) and then he would flash his load and then back to low battery, until it ends by died.
Now it shows even not any light when I plug in the power adapter and start not upward, the battery light blinks just and nothing else.

Help would be appreciated!

I think the problem is the battery. Remove the battery from the laptop, connect only leave, adapter / it connected ten minutes and try to restart your laptop.

Please let us know what happens when you do this.

Tags: Toshiba

Similar Questions

  • Satellite A100 - freezes if the blue light turns

    When the blue light comes on the touchpad turn high freezers.

    Also what cause the blue light comes on?

    You must give us a few more details.

    What Satellite notebook you have exactly?
    What operating system do you use?

    What blue light do you mean? Is it always or sometimes only?

  • Satellite L300 is dead - the battery light blinks orange 6 times

    Does anyone know what was the cause of this yellow flashing light?
    I have the same problem with a Satellite L300.

    Battery light flashes orange 6 times when I press the power button and nothing else happens. Dead laptop.
    I just picked up a service guarantee yesterday where they replaced memory card and the mother.
    He worked for 45 minutes then screen erased and won't turn on again.

    Anyone know about this problem?

    Hello

    The blink code provides some kind of clerical error, and this error is not always the same.

    Individual booklets are equiupped with different motherboards and provide different codes.

    It looks like a hardware problem and therefore, you should contact the ASP again.

    The warranty is still valid and you should take it!

    Don t waste time own investigation but get in touch with the guys again and explain your situation and that this error has occurred again.

    Welcome them

  • Re: Satellite A100-662 - new compatible battery

    Hello

    I have a satellite A100 - 662.
    The battery is a Li-ion battery / / model PA3399U-2BRS number / / DC 10.8V / 4000 mAh.
    My battery is flat. It is impossible to recharge. The charger is ok.
    I want to buy a new battery, but I think that this model does not close.
    You know a model equivalent and compatible?

    Thanks a lot for your answer.

    It is quite easy to find information on a new battery.

    Look on the Toshiba site, you can search for this type of accumulators.
    http://EU.computers.Toshiba-Europe.com => devices & Services-online Options & accessories-online Options and accessories homepage.
    There you can choose your laptop (Satellite A100) and you will see all the power options and a list of compatible batteries.

  • I can't start with Satellite P10 by pressing the power button more

    I can't start my Satellite P10 by pressing the power button more.
    Sometimes, very rarely its starts when I hold the power button for a while say 10 seconds.

    I tested the power supply and a battery to my friends P10 (of the same type) and both work very well.

    So it must be a problem with the key.
    No idea what to do?

    Thanks for any help

    The best.

    Tobias

    If it s a button or a power supply electronic problem, then you can't do anything.
    In this case assistance by the technicians of laptop would be necessary.

    But the next time that you should try this option if the laptop turns on not;
    Remove the battery and unplug the AC adapter from the laptop for about 30 min.

    After this short period of time to reconnect the two parts and check if the laptop could start.

    Good luck

  • I install the spilitter of bandwidth for isa server 2006 after the stoped.i of the microsoft firewall service cannot start this service and I take the error 1068-how do I do

    I install the spilitter of bandwidth for isa server 2006 after the stoped.i of the microsoft firewall service cannot start this service and I take the error 1068-how do I do?

    Hello

    Your question is beyond the scope of these forums.

    Please use the following links for that matter.

    Network Infrastructure servers Forum:
    http://social.technet.Microsoft.com/forums/EU/winserverNIS/threads

    Category of the Windows Server:
    http://social.technet.Microsoft.com/forums/EU/category/WindowsServer

    Concerning

  • I tried Windows 10 and after 10 days of hell, I asked them to uninstall.  But went with is my old Acrobat Reader.  I tried to use it, but it says that my browser plug is missing and that it cannot start because MSVCP120 is missing on the computer too.

    I tried Windows 10 and after 10 days of hell, I asked them to uninstall.  But went with is my old Acrobat Reader.  I tried to use it, but it says that my browser plug is missing and that it cannot start because MSVCP120 is missing on the computer too.  A friend told me that I have to uninstall and then re-install again.  I am a 71 years who does not know what to do.  Help

    Hi jimm13886845,

    Of course I'll help you get this problem is resolved.

    Run this cleanup tool to uninstall any old version of Adobe Reader Download Adobe Reader and Acrobat tool - Adobe Labs.

    Restart your computer and then installer you old version of Adobe Reader using this link Adobe - Adobe Acrobat Reader DC Distribution.

    Let me know if you encounter a problem, we will be happy to help you.

    Kind regards

    Nicos

  • Satellite A100-new or old battery is not

    Hello
    I have a Satellite A100 - 543 (PSAARE).

    The original battery was not charging so I bought a new. Now a new charge or the other. I then ordered a new charger before coming on this forum so I'll try that when it happens, but I think that the problem is not resolved.

    With the new battery, the icon says "10% usable, plugged, in charge. The icon, when the laptop is first turned on, shows the load bar moving (load) but after a few moments, stop.

    With the old battery in the icon says "connected, charge." It shows the empty.
    In both cases, the battery light is on.

    If I get the charger to the laptop computer, the computer stops immediately.

    Trawl the forums I see one proposed solution is an upgrade of the BIOS. I have the BIOS version 5.80
    See: http://www.laptoprepair101.com/laptop/2006/05/23/toshiba-satellite-a105-battery-charging-problem/comment-page-19/#comment-151154

    However I can not find my model (see above) on the list of Toshiba! It was purchased in France and out of warranty.

    Again I am doubtful that this will solve the problem.

    Others point out the motherboard. How I know this? If it's someone have an idea of the cost?

    I hope someone can help.

    Henry

    > It looks like the card main load circuit has a defect which is not cost effective to repair.
    Yes, it seems that Yes. Looks like only a mobo replacement could help

  • Satellite Pro 4600 calibrate the battery?

    Hello

    My Satellite Pro 4600 battery is pretty weird. I always completely load to 100%. But when I use my laptop and it reached 60-65%, it goes down to 3% of the battery. Now, I was wondering if there is a way to calibrate the battery, so he sees it as a battery of 100% full again? Anyone who can help me?

    Thanks in advance

    Hey,.

    Tips for the battery charge.

    Unplug the computer from the power adapter and turn it on. Let the computer battery power until the computer turns off, indicating that the battery is fully discharged.

    Remove the battery.

    Using a soft cloth, wipe the battery packs connectors and AC adapters.

    Reinsert the battery.

    Plug the power adapter from the computer and check the wall outlet, ensuring that the connection is firm.

    When the PC is off, let the battery charge until the icon or the battery light turns green.

    Disconnect the power adapter.

    Remove the battery.

    Wait 30 seconds and reinsert the battery.

    Reconnect the AC adapter.

    Let the battery recharge until the battery status light turns green or the icon appears at 100%.

    Now your battery must be charged completely. Unplug the computer from the wall outlet and turn on the PC. You should notice more autonomy.

    See you soon

  • Re: Satellite A200-14F - after 10 minutes, as the battery is just 10% of 100%

    Hello

    My question is simple. When I use my laptop computer and I use the battery power, the battery icon shows me after 10 minutes that the battery is just 10% of 100%. Does that mean that my battery is "dying"? Should I buy a new one?

    Thanks for help.

    Tomas Fric, Czech Republic

    I'm afraid you are right and your battery loses capacity because it doesn t work properly.
    Remove the battery and check the part number on the sticker. Use this number to order a new one.

  • I just installed an airport extreme router and WiFi works, but the status light still flashes.

    I just installed an airport extreme router and WiFi works, but the status light still flashes.

    Open airport utility... Click EI... and see what the cause of the problem. It will give the list of questions on the summary page. Click on each of them and he will offer you even solutions.

    for example the firmware needs to be updated... nothing major... or DNS is wrong or double NAT...

    Without our crystal ball, we do not know what is the issue.

  • The battery light flashes slowly when computer is off (G6 computer 2011sa) portable

    HP Pavilion 2011sa G6

    Windows 7 64 bit

    The laptop is brand new, I got it for a week.

    This seems to happen when the battery is low, but not to the level of criticism. Initially, I notice the battery light is white for about 30 seconds and then off for 30 seconds and repeat - what happens when the computer is turned off. I turn on the computer and the battery meter shows 29% and a ridiculous time, 43hrs 29minutes. Previously, he said 127hrs. But it seems to be frozen at this value. The battery light is now flashing white and turn off more quickly. Finally the computer just turns off without warning. After recharging the battery meter displays a time in more realistic and there seems to be no problem.

    Go to Device Manager. Expand the device Batteries and right-click on the "'ACPI control method-Microsoft compatible battery ' and select uninstall." Now, do a right-click any device and select ""find the hardware changes " option." Your operating system must be reinstalled a clean copy of the ACPI Microsoft-compatible remote control battery method while parsing. Now, restart your laptop.

    Please post here your positives or negatives in your thread, while others may have of your experience with this method.

    You have installed the operating system - improvements and fixes from the web to your mobile support portal?

  • After that the BIOS update cannot start my Satellite L305-S5885

    Last night I've updated the BIOS of my laptop, but when the completed BIOS flashing, she restarted Windows. The machine could not start. The CD/DVD device go into a cycle with a yellow light and the screen does not appear anything. Can someone help me solve this problem.

    Old Bios: v1.40
    New Bios: v1.50
    OS: Windows XP with SP3

    I can't use the CD/DVD device to start with a Win PE.

    Thank you

    Hello!

    I think that the BIOS was not correctly because your computer laptop doesn't start up again.
    In this case, you can make t a lot of.

    Try this: remove the battery and the AC adapter, wait up to 1 hour and then connect the battery and AC adapter. Try it again and hope it works.

    If this does not work, you should contact a local ASP. In the worst cases, the motherboard must be exchanged :(

    Welcome them

  • Satellite A100-785 - after the virus the bus USB and wireless do not work

    Hello
    I have a Satellite A100-785 with Vista 32 bit.

    I installed the Windows updates and another program. My antivirus detected a virus and delete files and now the USB bus and wireless do not work.
    I downloaded and installed a new driver for my model, but it does not work.

    Help, please!

    And, I want to recover the factory setting but I don't have a recovery CD now. How can I restore to factory settings? If cannot repair with the method of mormal and kare without recovery CD.
    See:
    [http://i39.tinypic.com/rw4f8p.jpg]

    Hello

    You should try to remove the devices that they are marked with a yellow exclamation point. Start Notepad, and then install the latest drivers from the Toshiba site.

    If the virus has destroyed an important system files that it s is no longer possible to install a driver and you need to reinstall Windows using the Toshiba recovery disc.

    Did you create the Toshiba Recovery disk? You can do this with the Toshiba recovery disc creator, which is preinstalled on your laptop. Maybe you are able to do this at the moment.
    In addition, you reinstall Windows using the recovery of HARD drive option. So go to the advanced boot menu and select Repair my computer. Some Windows files will be loaded and then you can choose the Toshiba Recovery option and follow the instructions on the screen.

    If you can t create the recovery disk, you must order a new Toshiba directly:
    https://backupmedia.Toshiba.EU/landing.aspx

    Welcome them

  • Satellite A100 - problem with the operation of the battery

    Hello!

    My laptop (I bought 1.5 years ago) has a big problem when you use with the battery.
    First of all, with a fully charged battery, the notification of "limited battery status" appears after 2 minutes of operation and after 5 minutes, he goes to the standby mode due to the level of the battery is very low.

    Then, I plug it into the AC power and the battery remains yellow for about 15 minutes light and then turns blue.
    (The battery is OK, I tested it on another satellite A100)

    What can be the problem?

    Thanks in advance!

    Maria

    Given that you have tested the battery in another satellite A100, the problem must be in the settings of your computer:

    1 > START > CONTROL PANEL > POWER SELECT THE OPTIONS ICON

    2 > you will now see a screen that shows your management food and note * one * has a tick that is a small point in a circle:

    3 > BALANCED > POWER SAVER > HIGH PERFORMANCE

    4 > THE PLAN OF POWER > CLICK ON CHANGE PLAN SETTINGS > WILL DISPLAY A SCREEN SHOWING YOUR PLAN!

    5 > GO TO > * CLICK * WHERE IT SAYS CHANGE ADVANCED POWER SETTINGS

    6 > IF YOU SCROLL THE BAR TO THE * SIGN + > BATTERY-CLICK * THE * SIGN.

    7 > YOU SHOULD HAVE: you will need to have play with these settings, or you can click on restore plan defaults to see if that will solve your problem

    Notes by clicking on the * + plus SIGN next to tany of these options below will allow you to change what event happens on your computer.

    + CRITICAL BATTERY ACTION

    + LOW BATTERY LEVEL

    + CRITICAL BATTERY LEVEL

    + LOW BATTERY NOTIFICATION

    + BATTERY LOW ACTION

Maybe you are looking for

  • Why full screen become Office precision?

    Well, as everyone probably - know everytime I go full screen its future's own space and ranked last in space than precision. Both cases make it so boring, and after searching around the internet preference and manufacturing system it stops I ask the

  • Drop-down menus are black boxes, namely:-bookmarks, address in the address bar type, click the mouse on the left. Help

    When I click on my favorites, the menu drops down, and the window is all black. I have to move the mouse around the fall down to to display bookmarks. This happens with the bat address and when I left click on the mouse. I uninstalled firefox and rei

  • Satellite 1800-514-display is off every few seconds

    Yesterday, I have a Toshiba Satellite S1800-514. I have install the OS (Windows XP Home) again.Laptop screen turns off every few seconds. When I press the small button above the power switch (sensor for portable fence) there is a beep and the screen

  • an ellipse to a blob image editing

    Hello. IAM new to labview and am treatment eyepiece-images to locate the center of the pupil. I got to a point to isolate the student from the rest of the image (binary) but now I like to adapt to an ellipse to it for a specific student center. I loo

  • Recover log.0000000001

    I am able to retrieve using log.0000000001 disaster recovery:"db_recover - c".But when I try to retrieve using the DB_ENV-> open (.), only the _db.001, the files are recovered, but not the file log.00000001.I use DB_ENV-> open (.) with flags DB_CREAT