Cannot turn off after the upgrade to 10.11.4

Similar Questions

• Mini Mac fails to turn off after the upgrade to El Capitan

  Hello

  Yesterday, I upgraded to El Capitan, unfortunately, the Mac mini does not stop and Finder is unresponsive, I am at a loss and do not know what action to take, any help would be much appreciated.

  Thank you

  rachealfromva

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  https://support.Apple.com/en-us/HT201295

  Subject of memory NVRAM and PRAM

  https://support.Apple.com/en-us/HT204063

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  https://support.Apple.com/en-us/HT201262

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  https://support.Apple.com/en-us/HT201314

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  https://support.Apple.com/en-us/HT204904

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• When I turn off my IPad wifi also turns off after the installation of IOS10. What is the solution?

  When I turn off my IPad wifi also turns off after the installation of IOS10. What is the solution?

  Hello. Do you mean "Turn off" or "sleep"? Your iPad there cell phones, or is it only WiFi?

• Inspiron 9300 screen turns off after the Windows Logo screen

  Inspiron 9300 my wife became severely infected.  I thought I had some weird things start popping up of the problem decided to wipe the hard drive and start over.  Unfortunately, I don't have to restore disks when I bought the computer.  I install windows xp pro service pack 2 full retail version.

  Installation was not a problem until I installed the driver ATI Mobility x 300.  I followed directions for installation from the website, do the installation of xp followed of the dell system software update followed of chipset followed video driver.  After that whenever I put on, the screen turns off after the Windows Logo.  The computer is still running and if I plug an external monitor everythng is fine.

  I tried all the troubleshooting tips I've seen in this forum.  I did a full install twice. made of safety boots (all right), started in VGA mode (works fine), I ran diagnostics from fn on startup, including express, extended and video tests and they pass all the controls.  I'm sure it's a software problem, but have been unable to solve.  I've updated the ATI bios although when I run it says already installed and done one installs x 300 driver on 6 ttimes own.

  I know it must be something simple that I'm missing. My system is the Inspiron 9300 with 2 GB of ram and the mobility x 300 card.  Any help would be appreciated.

  
  

• Display does not decrease or turn off after the time specified in the power settings.

  Hello

  I have HP Pavilion dv6-2140's. It is 1.5 years old. For a few days, my computer doesnot dim laptop screen or stops itself when not in use. I did the settings or power options. tried both recommended hp and energy saving. waited for several minutes, but neither the screen became decrease or stop. It was plugged and I slept something, but I knew he would go to standby mode after 15 minutes, but when I woke in the morning, he was still on with its full brightness for nearly 6 hours! That's what really shocked me, and then I checked for everything on google, but couldn't find anything. So please help me. Why is it so. I didn't install anything, nothing updated.

  Thank you

  Please update the latest version of the BIOS for your laptop and also check if your laptop screen is turned off when the unit works only with the battery.
  Go to control Panel\All Control Panel Items\Power Options\Edit Plan Settings and configure the parameters of the battery and check if the display turns off. In case it does, you can try then configure the parameters of the plan when the unit is plugged.

• The computer screen does not turn off after the specified power Options

  I tried several ways on trying to turn off my monitor of my laptop through the options of food and the use of some applications such as nircmd but nothing works every time. I'm sure it can be a program I am not using a device. I have a wireless mouse plugged into a USB port, but I know that's not what is keeping the PC awake, as always happens when it is not plugged. The thing that bothers me is I don't know how to identify this process shut off and I tried to put end as many process I can safely or those that I am knowledgeable in the subject to close. I would really like this feature back. Thanks in advance for the answers and ask if all the details are needed.

  I understood what was the 'problem '. It turns the screen of my laptop never turns off if my laptop is installed on a sloping surface, because it assumes that I'm working on it. When I went to bed my laptop on a flat level surface, is power does work normally, as reduces the brightness of the screen to the bottom, then turns off after a while. I guess it must be a form any a single function on my laptop. Thanks for all your answers.

• iPhone 6 touch id cannot be added after the upgrade ios 9.3.5

  My iPhone6 more ' Touch ID ceased to operate after the sound ' iOS to 9.3.5. This never happened with the previous iOS updates. Soft reboot (button home + power until the display of the apple logo) didn't work. Turn off the two "use Touch ID" for Unlock iPhone & iTunes App Store, then reboot and or soft reboot didn't work. Tried to 'Add a fingerprint', but as soon as it has been exploited, it goes directly to the page saying: 'FAIL' unable to complete installation of contact ID. Back... I even deleted all to restore my backup who had an operation 9.3.4 iOS, but then, I realized that after the restoration, put also got iOS updated! (I'm back to 0). Please help if you have any other fix for this? Thank you.

  Restoring as a NEW phone using iTunes (do not use backup at all).  Adding 3rd party applications, try the contact ID.  If it still does not work, then you have a hardware problem and will need to bring the phone to Apple for the assessment.

  Best,

  GDG

• BlackBerry Q10 Q10 cannot turn off after 10.3

  I have improved my Q10 to 10.3, after that that it restarts after several minutes since I turn it off. This means that I can't turn it off and it is still running on automactially. But it can be turned off while charging.

  Perform a simple reboot on the BlackBerry this way: with smart BlackBerry poweredphone, remove the battery for a minute and then reinsert the battery to restart. A reboot in this manner is prescribed for most defects and errors of operating system, and you will lose any data on the device doing so.

• Latitude D610 screen turns off after the Windows XP loading screen

  I'm having a problem with my Latitude D610 where after the Windows XP loading screen, the screen turns off completely. No BSOD, no login screen, just a white screen. This started happening at least a year, however, I bought a new computer if it is passed to the hatch. I tried the system restore when it appeared first without success. The computer starts in Mode safe. Any suggestions?

  If it starts in mode without failure, then its almost certainly a driver and with the blank screen problem, I suspect a display driver.

• XP - cannot install updates after the upgrade to Quickbooks 2010

  I am running XP Professional.  Since the upgrade to Quickbooks 2010, I can not install three MS updates, and can I update Adobe Reader version 8 to version 9.  The MS updates remaining in my queue are:

  1 Microsoft.Net Framework 3.5 Service Pack 1 and the .NET Framework 3.5 Family Update for versions of .NET 2.0 to 3.5 (KB951847)

  2 Microsoft SQL Server 2005 Express Edition SP3 (KB955706)

  3 update for .NET Framework 2.0 SP2 and 3.5 SP1 on the Windows 2003 and Windows XP x 86 service provider (KB983583).

  It has been several weeks now and today my TrendMicro PC-Cillin Internet Security 14 security check revealed that I have for very high Security - Bulletins-MS10-056 and MS10-060

  What can I do to fix these problems

  Assuming (by reference to one of the titles of any updates you are 'problems' with) you have Windows XP _ Edition with Service Pack _ 32-bit - here's what I suggest:
   
  Clean and fix the usual suspects

   

  Restart, and then log on as a user with administrative privileges.

  Difficulty your file or registry permissions...

  Ignore the title and follow the subsection under
  "Advanced Troubleshooting", titled,
  "Method 1: reset the registry and the file permissions.
  http://support.Microsoft.com/kb/949377
  * will take time
  * Skip the last step (6) - I hope you have SP3 installed.

  But if not - is not the time.

  You may see errors go even if you watch, count upwards.  NO.
  worries at the moment.

   

  Restart, and then log on as a user with administrative privileges.

   

  Download, install, execute, update and perform a full scan with the following
  (freeware version):

  SuperAntiSpyware
  http://www.SUPERAntiSpyware.com/

  Restart, and then log on as an administrative user.

  Download, install, execute, update and perform a full scan with the following
  (freeware version):

  MalwareBytes
  http://www.Malwarebytes.com/

  Restart, and then log on as an administrative user.

  Download and run the MSRT tool manually:
  http://www.Microsoft.com/security/malwareremove/default.mspx

  You find nothing, you will only find cookies, you may think that it is a
  waste of time - but if do you these things and report back here with what you
  / don't think you do all that - you add more parts to
  the puzzle and all of the picture just may become clearer and your
  problem solved.

  Restart, and then log on as an administrative user.

  Download/install the latest program Windows installation (for your operating system):
  (Windows XP 32-bit: WindowsXP-KB942288-v3 - x 86 .exe)
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=en

  Restart, and then log on as an administrative user.

  Download the latest version of Windows Update (x 86) agent here:
  http://go.Microsoft.com/fwlink/?LinkId=91237
  ... and save it to the root of your drive C:\.  After you have saved in the
  root of the C:\ drive, follow these steps:

  Close all Internet Explorer Windows and other applications.

  AutoScan--> RUN and type:
  %SystemDrive%\windowsupdateagent30-x86.exe /WUFORCE
  --> Click OK.

  (If asked, select 'run.) --> Click on NEXT--> select 'I agree' and click
  THEN--> when it completed the installation, click "Finish"...

  Restart, and then log on as an administrative user.

  Visit this web page:

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  ... and click on the "Microsoft Fix it."  When asked, select "RUN."
  both times.  Check the box "I agree" and click "next".  Select the check box

  
  to "Run the aggressive options (not recommended)" and click "next".  Let
  He finish and follow the instructions until it does.  Close/exit and
  reset when it is.
   
  You should now perform a full CHKDSK on your system drive (C :)...)

  How to scan your disks for errors
  http://support.Microsoft.com/kb/315265
  * will take time and a reboot

  You should now perform a full defragmentation on your system drive (C :)...)

  How to defragment your hard drives
  http://support.Microsoft.com/kb/314848

  
  * will take time
   
  When is the last time you checked the updates for your motherboard
  chipset drivers, device/video card drivers, sound card / drivers
  and the credit card network / device drivers?  You can do now.
  The easiest way is to visit the website of your computer manufacturer
  If it's something like Dell, HP, Lenovo, gateway, etc.  There, you can
  Find the support/downloads/drivers section and look for the drivers
  for your computer model.  I suggest you obtain these updates.

  Uninstall applications from any third party firewall (ZoneAlarm, etc.)
  and use the built-in firewall of Windows only.

  Log in as a user with administrative rights and open Internet Explorer
  and visit http://windowsupdate.microsoft.com/ and select to make a
  CUSTOM scan...

  Whenever you are about to click on something in these pages - web
  first of all, press on and hold down the CTRL key while you click on it.  You can
  release the CTRL key after clicking on each time.

  Once the scan is complete, select that ONLY updates of high priority
  (deselect all others) and install it.

  Reboot again.

  If it worked - try the web page - selection not more than 3-5 a
  time.  Reboot as needed.

  The optional software updates are generally safe - although I recommend
  against the 'Windows Search' one and all of the "Office Live" those or
  "Windows Live" which for the moment.  I would like to avoid completely the
  Optional hardware updates.

  Seriously - do these things.  It's like antibiotics - do not skip a single
  step, don't leave because you think it will be ok now - review
  until the end, until you have done all given in the order shown.  If
  you have a problem with a step to ask and let someone here, you get
  Thanks to this step.  If you do not understand how to bring one back
  and ask here on this step and let someone guide you through it.

  Then - actually - that everyone here knows if it worked for you - or if
  you have more questions.

  
  --
  Martin Stanley
  MS - MVP
  --
  How to ask Questions the Smart way
  http://www.CatB.org/~ESR/FAQs/smart-questions.html

• System turns off after the connection because UPS is misconfigured

  Installing a UPS on XP as he said "he couldn't communicate with battery backup.  I suspect (pretty sure) I put the codes, i.e. signals for the loss of power senseing incorrectly.  So when XP starts, connects and defines then personnal settings immediately it detects a loss of power and down, it is to say newspapers turns off and stops.  By inserting a bootable disc, I get the display for differnet start modes, etc. without danger, but the arrows do not work.  He maintains "normal" startup  So, I'm in a loop.  Pressing F8 does nothing.  I tried several times with the same results.

  Can I get a bootable CD to somehow allow me to set the operating system to default values?  Or would that even work?

  Is this really what the message really says:

  He couldn't communicate with battery backup

  What is the brand and model of your UPS and you have the correct wiring to it and the installed software?
  Configuring UPS never worked correctly before?
  What do you mean "set you codes loss of power properly detection."

  What bootable disc are you using?

  If you think that the XP UPS Service gives you a hard time, you can start the XP Recovery Console and disable it.

  If you have any bootable installation CD XP authentic where you can start in the XP Recovery Console, so you can make a bootable CD from the Console of the Recovery XP (no XP media required) and then just disable the UPS Service does not start during the next reboot.

  Once you enter the Recovery Console, type this command:

  turn off the UPS

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and don't forget (no support for XP not necessary).

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

• HDD turns off after the mode 'sleep'?

  I would like to know if the hard drive would turn out or not after the mode 'sleep'.

  Does anyone have any suggestions?

  Thanks in advance for your suggestions :>

  The computer do not hibernate unless it stops the disc after writing the hibernation file.

  Mode for similarly low-power stop discs 1

• Re: satellite A300 screen turns off after the toshiba logo, will not boot from the CD/DVD

  Hello, I have this problem with Toshiba satellite A300.

  I deleted several files and folders of my drives C and E. To restart the computer, it only shows the Toshiba logo then a slightly gray white screen on a thorough inspection. Whenever I press CRL + ALT + DELETE, the computer restarts and behaves in the same way.

  I tried to use an external monitor, but there is no difference. The tent to start using a CD/DVD, same behaviour occurs, it does not start and screen remains blank after the Toshiba logo, I tried even to change g the order of boot, but in vain.

  What could happen?
  Thanks in advance.

  Hello

  It seems that you deleted system files and Windows no longer starts. Have you tried to restore the disk image factory settings or hard drive recovery? Or do copy the Windows installation... It is easier to reinstall rather fix the problem.

• How to stop the narrative turn off after the end of the video track?

  Hello world.

  As the title says, how can I disable this "feature" absurd? This issue of unique break literally makes the unusable software for me.

  I combed the Panel options and found nothing obvious. I combed also internet to see this: https://helpx.adobe.com/premiere-elements/using/create-narrations.html , which says:

  When you have finished narration, click the Stop button.

  An audio clip containing the narration is added to the active panel of the project and to the Narration track in the timeline of Quick view or the calendar of the expert opinion (below the selected clip).

  Note:

  If you do not click the Stop button, recording stops automatically at the beginning of the next file in the Narration track, or 30 seconds after the end of the last item in the quick view chronology or timeline of the expert opinion.

  Really? I did something wrong or is - this software really broken by design? The design team has already considered that a user might want to tell first and extend video to the narrative later? Is it possible to disable this "feature" break or get a refund if not?

  Thanks in advance.

  Stark Zodiark

  Just in case reference. This isn't Adobe. Instead a user. The frequency of the presence of Adobe in this forum is not defined.

  By the nature of your question, I'll give you the information to return/refund first...

  If you bought the first elements 13 Adobe for download in the last 30 days, you can request a return/refund. Please visit the following link.

  Return, cancel or change an Adobe order

  You can also go to another path (probably takes you to the same place) orders of Adobe's cat.

  Contact the customer service

  First Elements

  Payment of membership, account,

  Payment order, invoices,

  Adobe Chat

  Now to your question.

  Please refer to ATR first troubleshooting items: PE: Narration recording stops after 30 seconds

  I wrote in 2013. He then applied and applies today 2015 for elements first 13/13.1.

  content is needed on a video track, an audio track, or the soundtrack to avoid the situation of "Narration recording stops after 30 seconds.

  The details related to this situation are included in the blog post with the link above.

  There is an Adobe feature Bug report request form that you might want to file with Adobe. The workaround is described in the blog post. I have not found (nor seen reports users say they have found) a way to change this requirement of storytelling other than what I have described in my blog.

  https://www.Adobe.com/cfusion/mmForm/index.cfm?name=wishform

  RTA

• Cannot access portfolio after the upgrade to iOS 10

  I haven't seen this pop up on other forums yet, but my iPhone 6 Plus does not double tapping on my lock screen after that I upgraded to iOS 10.

  I went into the settings of the portfolio and Apple pay and made sure that allow access when it is locked is on.  Does anyone else know this?

  I'm having the same problem