Cannot use the mouse with the laptop wireless

Similar Questions

• Satellite A210 - 27 M (PSAELE) cannot use the new wireless network card

  Hi all

  I changed my wi - fi for Atheros AR5b91 and hardware network card is locked.
  I can't remove this lock of wi - fi switch or fn + F8 probably it's the lock of the bios.

  I tried to unlock it on Windows Vista, Windows 7, Ubuntu, so it is not caused by software.
  I tried the card WiFi on another laptop (toshiba not) and it's ok.

  If anyone can help?

  Thank you

  Hello

  To me, it seems that you used is not compatible Wlan module.
  But I found this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=79237

  A user was unable to activate new update Intel Wlan card.
  According to some information, its possible to enable the Wlan card by covering pin 13 on the wireless Mini-PCI network card.
  But to be honest I've ever tried and I would use this workaround with caution.

• Cannot use the printer wireless

  I use Windows 7 and my computer is connected to the internet. I can't print wireless, I was able to before but not now. The printer is wireless and shows that it is connected. I tried to reinstall the printer, following the programs in case of problem, but everything for nothing. I was able to print a test page, but it happened once and now nothing prints. Another computer has no trouble printing to the same printer.

  What is the brand and model of the printer?

  How it shows that it is connected?

  What is the brand and model of your wireless router?  Please, look at the label on the back or the bottom of the unit and include any version of the material mentioned.

  This problem occurs quite frequently with wireless printers, usually when the printer has been turned off for a while during which other devices are connected to your wireless LAN.

  Printers almost all (if not all) are configured by default to automatically get an IP address from your router wireless.  When you initially installed the printer, Windows found the printer to this IP address and set up the printing system to direct its output to this IP address.

  If during the time that the printer is turned off you connected to other wireless device (for example, another computer or smart phone), the router can assign the originating IP address to the other device.  The router will then assign a new IP address to the printer.  The problem is that Windows is always configured to print to the original IP address... but the printer is no longer there.

  The solution is to assign the printer an IP fixed or 'static' instead of him to use its default value to obtain an IP address automatically.

  To confirm the diagnosis above, read the manual of your printer and either print a configuration page or use the LCD of the printer (if she has one) to show its current IP address.  Write it down.

  On the Windows 7 computer that does not print, open devices and printers.

  Select (click) any printer.

  Click on 'Print server properties' on the toolbar at the top of the printers and devices window.

  Select the "Ports" tab

  Scroll the list of 'Ports on this server' until you find the one for your printer.

  Expand the 'Port' column until you can see the full IP listed for your printer.

  If the IP listed here is different from the IP address by your printer, you will need configure the printer to use a static IP address.  If the IP address here is the same one reported by the printer, you have a different problem.

• 7515 printer is networked but used the laptop wireless printing.

  Tried to reinstall software online version and CD. Rebooted the modem, router, printer and laptop in the sequence. tried the hp and doctor downloads hp diagnostic utility. Network appears on the printer as 'OK' and all the statistics in the reports are very good too. The network has only one name and is secure. What can I do for the new printer will appear and print from my laptop without using a USB cable?

  Frustrated, in California.

  Best regards, Diane_2012

  Yes! I solved my problem... I deleted the original software and reinstalled the software and now the printer will print wireless!

• When you use the question mark, appears like a capital E with accent French and cannot use the quotes.

  Original title: I can't use my question mark (rises like a capital E with accent French and cannot use the quotes)

  I'm having a problem from time to time with my ability to use marks quotaion, brands etc. How can I treat it DEFINITIVELY the question.

  Thank you

  Hi golfnut11,

  1. you are using a laptop?

  2. you remember to make changes to the computer priro to this question?

  Step 1:

  If you use a laptop, check if the FN key is enabled. If so, then try to turn it off and check.

  Step 2:

  You can also try to check the keyboard on the screen and if the problem occurs or not.

  Check out the link:

  Type without using the keyboard (on-screen keyboard)

  http://Windows.Microsoft.com/en-us/Windows7/type-without-using-the-keyboard-on-screen-keyboard

  If you use a Microsoft keyboard, you can also consult the following article:

  Troubleshoot wired keyboards that do not or only the erroneous characters category
  http://support.Microsoft.com/kb/258826

  Hope this information is useful.

• I downloaded the new version and it says: you cannot use this application with this version of Mac os how can I download the older version?

  I downloaded the new version and it says: you cannot use this application with this version of Mac os how can I download the older version? My os is 10.4.11

  You can read this article: Firefox no longer works with Mac OS X 10.4 or PowerPC processors to read about the EOL for Mac 10.4 support and what the best options going forward.

• Im trying to fill the network so my ps2 connections can use the signal wireless to my laptop running vista Basic. When I click to bridge, I get a message saying that I need at least 2 internet connections. is this in any way about this?

  Im trying to fill the network so my ps2 connections can use the signal wireless to my laptop running vista Basic. When I click to bridge, I get a message saying that I need at least 2 internet connections. is this in any way about this?

  Hi Jer9009,

  Welcome to the Microsoft answers site.

  ·         Could you give the exact error code or error number you get?

  To connect multiple computers, install a network adapter in each and run a network CAT5 cabling to connect each one to a hub (and thus the other.) The computer that will serve as a transition will have a standard network card for wired and a wireless network adapter that will connect to the wireless (WAP) access point or gateway on the second network.

  A network bridge is software or hardware that connects two networks or more so that they can communicate. You can create only a single bridge network on a computer, but a bridge can handle any number of network connections.

  For more information, see the link: create a network bridge:http://windows.microsoft.com/en-US/windows-vista/Create-a-network-bridge

  Add a connection to a network bridge: http://windows.microsoft.com/en-us/windows-vista/Add-a-connection-to-a-network-bridge

  Swathi B - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot use the functions F1-12 on my Satellite C55 - A - 19 K

  Hello

  Satellite C55 - A - 19 K have a keyboard drivers?
  I cannot use the functions F1-12 and can not get the wireless since it s on the keyboard...
  Any 1 can help please?

  This function is not controlled by the driver keyboard, but with utilities and tools specific to Toshiba.
  What operating system do you use?

• Magic of the network hit all the computers off line when the laptop wireless on signs

  I have Network Magic V. 5.1.9055.0, a G from Linksys WRT110 wireless router. Online at any time may be all or part of the next list computers/gamers, computer hand Win XP sp3 is connected to the router, Samsung clp300 printer lazer connected to the main computer as a server, Vista sp2 office connected to the Wii, PS3 wireless wireless router and laptop Vista sp2 wireless. Whenever the laptop wireless comes online, it will stop magic network until the wireless is fully initialized and online, it strikes all onlines offline until there is a full boot of the wireless.

  Very frustrating since we went all the cisco and spilled a belkin router that worked perfectly with the above configuration. (unfortunately I gave the belkin far and no longer have access to it or I would have released this new linksys and would be happy to once again) I don't understand why cisco units cannot work together in harmony?  In any case, I can't find any info on the help of linksys or the magical sites network which brings me to this forum. Need help, please notify...

  I removed NM v5.1.9055 three computers and re-installed to v 5.5.9118. inserted my key and re started to each of them. When the laptop wireless started it off the other two for about 3 minutes until the phone was fully charged while we were back on the line. The poster always online in the map view, the internet router is and the laptop (Vista) shows online, but the report to other computers (1 XP and 1 Vista) shows red and offline. Always frustrating because it's all working without error until I installed the linksys cisco router then the trouble started... still need help...

• Portege R700: Cannot use the two SVGA HDMI on the Port PA3838E-1PRP Port Replicator

  Dear all,

  I have a Portege R700 series (PT311E) and a high speed P/N PA3838E-1PRP port replicator.

  Today, I tried to connect two external monitors on the VGA port and the second HDMI port replicator port.
  Unfortunately, I was not able to configure the laptop / duplicator to * work with external monitors stand *.

  Do not work in this way portable stand and port replicator becomes useless.
  Although it is a default installation on other products manufactured without drivers and special parameters will be needed, I hope that in our case a key combination or a driver may resolve this problem.

  To be even more precise, I don't want to also use the laptop screen. I want to just connect laptop closed and turned off in the duplicator, to turn on the laptop the power button of the port replicator and to have the image on two external monitors.

  Thank you for your quick responses,

  Best regards

  Cristian

  Hello

  What R700-xxx you have exactly?

  How to connect two monitors? Are the two monitors connected only to the Port Replicator or is one of the monitor connected to the laptop and the other monitor is connected to the duplicator?

  Could you please post this?

  I'm not quite sure of HDMI and Port Replicator (PA3838E-1PRP) but many laptops equipped with support DVI dual video output (VGA and DVI) port using Advanced Port Replicator III (PA3314E-1PRP) or Advanced Port Replicator III more (PA3474E-1PRP).
  But this is only possible if the laptop itself supports the simultaneous use of RGB & DVI too.

• X 230 bluetooth does not work - cannot use the cell phone as personal hotspot

  I try to use the bluetooth in my X 230 to connect my laptop with my cell phone. I want to be able to use my cell phone as a personal hotspot, where I am in an area where no WiFi secure. I would have thought that it would be a standard feature in a laptop that is presented as a business device, but apparently this is not the case.

  I installed the bluetooth driver and the updated system, as suggested by joelle...

  http://support.Lenovo.com/en_US/research/hints-or-tips/detail.page?&docid=HT073834

  and

  http://support.Lenovo.com/en_US/downloads/detail.page?docid=DS012808

  ... but it's still not working for me. I am now able to connect my mobile phone to my X 230, but instead of allowing me to access the internet via bluetooth, a dialog box appears that allowed me to play songs that are on my cell phone using the laptop speakers.

  I am disappointed that bluetooth driver has not come pre-installed on the 230 x, and I'm disappointed that I'm not able to use my cell phone as a personal hotspot for my x 230.

  I solved the problem myself by following the instructions on this page.

  http://www.kevintaber.com/2012/05/25/iPhone-personal-hotspot-via-Bluetooth-tethering-to-Windows-7/

  In Windows 7, go to the control panel > hardware and sound > devices and printers
  Then right-click on the bluetooth device (in this case, an iPhone) and choose Properties
  Deselect all EXCEPT Personal Area Network Access Point

• Error 1721 when you try to install the Sprint SmartView software to use the Sierra Wireless 598U device.

  Error 1721 when you try to install the Sprint SmartView software to use the Sierra Wireless 598U device.

  It comes with Vista, upgrade install and activate Forum.

  http://social.answers.Microsoft.com/forums/en-us/vistanetworking/threads

  "Connect to a network, mail and the Internet."

  They will help you with your question in the Vista Networking Forum above.

  See you soon

  Mick Murphy - Microsoft partner

• Users on the network cannot use the files after upgrade to Windows 10

  When I switch to win 10 people on the network cannot use the files on my computer

  Hello

  Thanks for posting your query on the Microsoft Community.

  With the description, I understand that you have problems with network connectivity and access files on network on your Windows 7 machine. I will certainly help you to the query.

  I would be grateful if you could help me with more information to better understand the problem and a solution:

  1 is this computer connected to a network domain or home?

  2. what exactly happens when users on the network try to use/access files on this computer? Do they get an error message/code?

  In the meantime, I suggest you refer to the below mentioned thread and check if this is useful:

  http://answers.Microsoft.com/en-us/Insider/Forum/insider_wintp-insider_web/Windows-10-network-file-sharing/18fba63e-7b6c-46FE-BA23-575a634fcee8

  Hope this information is useful. Please write us back with the required information for assistance, we will be happy to help you.

• Cannot use the Start button

  For some reason, when I try to click on the Start button, it disappears.  I tried all day to dissable addons that sort, but it ended up doing another way.  I have restarted computor, but the Start button, always goes away until I can click on it.  Everyone comes through this before please?

  Hello BeverleyMacKenzie,

  Thank you for the question!

  I'm sorry to know that have problems you with start button. As I understand it, you cannot use the button start effectively.

  Method 1: perform the scan SFC (System File Checker) and see if the problem occurs.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  Method 2: use the Microsoft Safety Scanner in full scan mode and to remove all the threats that is not detected by it and see if the problem persists.

  Microsoft safety scanner

  Note: the Microsoft Safety Scanner expires 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  The Microsoft Safety Scanner is not a replacement for the use of antivirus software that offers continuous protection.

  Answer to us if you have problems with start button or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• Lightroom cannot use the catalouge named 'Lightroom '.

  I read online for a solution for this for two hours. I tried all the solutions I found. Please can someone help me with this error message

  "Lightroom cannot use the catalouge named 'lightroom' because it is not writable and cannot be opened.

  I changed the permissions, without success.

  I ran as administrator with no luck.

  There is no current lock file.

  What else can I try?

  Thank you very much

  At this point, I think that you need to restore a recent backup of your catalog file.

• Hello, I have Lightroom and Photoshop CC on a mac and a PC laptop. I bought another mac now and no longer want to use the laptop PC (windows). What should I do to load them on the new mac? First remove the applications from the laptop?

  I have Lightroom and Photoshop CC on an imac and windows laptop PC. I've now bought another mac and want to use the laptop to windows. I need to remove the applications from the laptop first, then download new mac?

  Hello

  Lol you should not remove it. You can turn it off with the signing of the application Adobe CC.

  Reference: connect and disconnect activate Cloud Creative applications

  And then you can install it on your other machine.

  Kind regards

  Sheena