Capacity issue series MCU 4500

Similar Questions

• Radion Series 4000-4500 greenscreens on you tube. any ideas?

  used the intel pentium 4 processor 2.8 ghz 2.79

  GHz

  1.50 GB ram

  32-bit operating system

  Windows 7 ultimate

  videocard ATI radion Series 4000-4500 pci

  L if you-tube on firefox, it blocks the 'window' and is unresponsive and the program closes

  If use internet explore tube you greenscreens on the Panel where the video should play, then this window does not respond but the can still use ie8

  to close ie8 l have the task of alt.ctrl.del and at the end which ie8 to farm/accidents

  This problem has been with me since you tube said l HAD to d/l flash 10.1 to "improve my performance a look" and wouldn't let me post vids until l DID d/l

  Flash 10.1

  l uninstal flash 10.1 and try to install again 9 and a window appears and says "there is a newer version more sucure version of flash player windows @ '.

  What l now please?

  Hi, you can disable hardware acceleration if you have not done. This has contributed to other users. Go to this site Adobe and right click on the Flash logo, click on settings, display settings. Uncheck the h.a.

  http://www.Adobe.com/software/Flash/about/   

  See if that helps,

  eidnolb

  Post edited by: eidnolb add link

• HP envy 4500 series: series like 4500 hp does not print

  printer prints test pages simply awesome.

  When I try to print, page comes out blank?

  Help, please

  Thank you

  John

  Hi @jsk4224,

  Thanks for joining the Forum from HP Support for a solution to your printing problem.

  I understand that you use a HP ENVY 4500 e-all-in-one printer with a Chromebook and and print pages of test very well but work sent from the Chromebook fate in white. I would like to help with that.

  Here is a support document which can help with this question - printer prints blank Page or fact not printing black or color ink.

  Please let me know if that solves the problem, or if you need assistance.

• AP DHCP issues after that 4500 IOS upgraded

  Hello

  Since we went to-: cat4500e-entservicesk9 - mz.122 - 54.SG.bin on our 4500 we had problems with our AP CAPWAP onto our 5500 controller.

  Debugs showed AP, that he cannot receive the IP address.

  DHCP: SDiscover 302 bytes
  * 00:37:02.140 Mar 1: B'cast on the interface GigabitEthernet0 0.0.0.0
  * 00:37:03.999 Mar 1: % CAPWAP-3-Journal of ERRORS: do not send discovery request AP doesn't have an Ip address.
  * 00:37:06.141 Mar 1: DHCP: attempt to SDiscover # 3 for entry:
  * 00:37:06.141 Mar 1: Temp IP addr: 0.0.0.0 for peer on Interface: GigabitEthernet0
  * 00:37:06.141 Mar 1: Temp subnet mask: 0.0.0.0
  * 00:37:06.141 Mar 1: DHCP Lease server: 0.0.0.0, State: 1 selection
  * 00:37:06.141 Mar 1: DHCP transaction id: BF5
  * 00:37:06.141 Mar 1: lease: 0 seconds, renewal: 0 seconds, relink: 0 seconds
  * 00:37:06.141 Mar 1: next timer triggers after: 00:00:04
  * 00:37:06.141 Mar 1: number of attempts: 3 Client-ID: f866.f21d.39d4
  * 00:37:06.141 Mar 1: hexadecimal dumping ID Client: F866F21D39D4
  * 00:37:06.141 Mar 1: host name: APf866.f21d.39d4
  * 00:37:06.141 Mar 1: DHCP: set SDiscover option class-id: 436973636F204150206333353030
  * 00:37:06.141 Mar 1: DHCP: SDiscover: sending of DHCP package for the length 302 bytes
  * 00:37:06.141 Mar 1: DHCP: 302 SDiscover bytes
  * 00:37:06.141 Mar 1: B'cast on the interface GigabitEthernet0 0.0.0.0
  * 00:37:10.143 Mar 1: DHCP: QScan: Timed out selecting State
  * 00:37:13.999 Mar 1: % CAPWAP-3-Journal of ERRORS: do not send discovery request AP doesn't have an Ip address. DHCP problem % unknown... No possible allocation
  * 00:37:19.265 Mar 1: DHCP: waiting for 10 seconds on the interface GigabitEthernet0
  Not in a bound State.

  I did debug on the controller, it gives the address over and over again. I don't see any message CAPWAP and the AP do not have an IP address.

  Not sure if I should roll back IOS, I see not an IOS cause such a problem?

  Any information would be appreciated...

  Thank you

  Brad

  Can do without the configuration of the DHCP server to any device L3 just in order to test?

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCth68708

  Bugs are always trigger... they don't knock code time that execute us...

  It will be great if we could apply externally and do a test...

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• MCU 4500 and video walls

  We are looking to buy a video wall for one of our large conference rooms. I'm just curious how the MCU will display on a video wall. I understand that a conference to the MCU will be only one stream as opposed to separated flows. However, say we get a video wall of 3 x 3, and we have 3 x 3 provision of equal size on the MCU. If we had 9 people at a conference together, I wonder if they would be distributed to each person on one of the screens, or if they have a chance of crossover.

  Again, I understand that the video wall is technically 1 display when the chaining of the TV and I know THAT this MCU as 1 stream, so I think it is possible, that he don't line up exactly how we want to. Anyone tried something like this before? I just want to see what we get in before we eventually purchase.

  Almost impossible to do as you want - it would be pure luck than good management to say things like that.

  Best solution would be to use a Laser/LED data projector; Full HD, not lamp so no hot upward or cool down time, not so dead quiet fan. We use two Projectors Panasonic PT-RZ470EAK Laser/LED in our medium-sized rooms (seating 40 people) - and they are absolutely great. :) Life expectancy is 22000 hours.

  Rooms next to get this development will be our rooms + 100 places.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Video upgrade capacity issues,

  

  HI, I am looking to update my video card on my hp pavilion p7-1003w,

  My specs are:

  AMD Athlon II X 4 650: 3.2 ghz

  8 GBof ram

  250W PSU

  Motherboard for N-Alvorix-RS880-formfat (Alvorix).
  Windows 7 64-bit,

  ATI Radeon 4200

  I would like to now if my computer would be able to run a:

  XFX ATI Radeon HD6670 1 GB DDR5 VGA/DVI/HDMI PCI-Express graphics HD667XZAF3

  effectively, and would be compatible.
  
  I've never updated my card video before and if you need any additional information, please tell me.

  -Conner

  The CS500 Corsair is a great choice according to other users on this forum. It is fully confirmed for if adapt to the space provide and has enough juice to do the job you want it to do.

  Frank

• Capacity issues - information planning does not appear in the dashboard / rims reports

  Hi all

  I'm still getting my head around time involved with the collection of data for projects.

  I had a data manager, collection of information on approximately 200 systems in 2-3 weeks, still in the dashboard I don't see any information I want to learn.

  If you look at the attached screenshots, you will see for the dashboard of the company, I have a 190 systems all in my a project for this company. Among them, only 2 have started to show that they have inventory. In data manager himself most systems already have some inventory information, but this has not filtered through the dashboard yet, apart from these two you see here.

  In my summary inventory systems capture screen you can see a lot of systems that display zeros in all of the inventory. In data manager if I find the system data, I can see his stats for most servers on all sections.

  So I have two questions:

  • Should I worry that this info does not yet show after 2-3 weeks?
    
  • How could I go to take 3 systems in this collection and the pulling of data using custom reports? I created a separate project for these three systems, added to them, they have 2-3 weeks of data collection already, but when I run my custom reports on these systems a lot of data is empty and does not appear do not, even if these three systems have all data and performance data I need when I view on the data Manager server.
    

  Any help would be greatly appreciated.

  Sean

  It resembles a P4 dual core with hyperthreading

  But yes, it seems 'normal '.  Thus, the collector operates.

  Here's the thing... If you add systems to the collector and then create a data sync before the first inventory collection... you ship a bunch of zeroes on the scoreboard.

  the collector will not send new data after the first synchronization, unless you use the full export option.

• San capacity issues

  I'm looking adding shared storage smb essentials more license. im not dicided weather to go with a virtual san or san of material at the moment. I read a little about the new sva vmware offering or a san hp of Créteil. the 2 questions I have is the 2 TB limit that vmware has. This limitation applies to external shared storage and if so the san, the only solution of partitioning is... also any entry on the sva weather occur near a san hardware

  Ty brand

  Hello.

  In vSphere 5, VMFS volumes can be up to 64 TB in a single measure, so the 2 TB limit is really now just around your VMDK files. VMDK (virtual disks) still cannot be larger than 2 TB - 512 bytes, you use VMFS or NFS data warehouses.

  In vSphere 5, you can use the compatibility mode physical RDM for volumes up to 64 TB of size in the comments. In other words, a guest operating system could have a RDM which is very large.

  Equipment storage VMware uses NFS. The question of performance is difficult, because you most likely get a lot more disks in a SAN hardware. You also compare block vs NFS. Again, it is a difficult question.

  Good luck!

• Capacity issue

  Can of print production support for AFP to PDF conversion? I have a project which should convert 50 million documents from AFP to PDF, then on a daily basis, there will be about 25 k which will need to be converted. Production printing support this capability? I was not able to find comparative data for analysis.

  Just like info, I'm not ready to contact an exec for sale at the moment, I am researching just our options. I need to determine if I should exclude Adobe for this project.

  Any help would be appreciated.

  Of course, Production Print can convert AFP to PDF format (or any other output format based on the page, by the way), but you have to be clear about what kind of AFP you use as input. The basic assumption is composed entirely of AFP, that is with all the online resources; If this isn't what you have, you may need to pre-treat your AFP to resolve all the dependencies.

  By experience, you can expect at a rate of about 1,000 pages / processor / minute. This will depend on the complexity of the AFP.

  You should definitely consider LC Production Print for you needs - feel free to post any follow-up questions.

  Best regards

  George

• All series on stacking MCU 5300

  Hello world

  As my topic above.

  I have several questions on stacking MCU 5300 series

  1. what type of series 5300 MCU only stackable? 5310 + 5310? or + 5310 5320? or + -5320 5320?

  2. If I cumulation 5320 + 5320 MCU, can I do conference call with 40 participants from HD in a room?

  3. How about the layout?

  4. What are the different between stacking and cascade MCU?

  Please advise,

  Thank you

  Ovindo Prastyo Utomo

  Hello Ovindo-

  For questions 1 and 2, you can take a look at this powerpoint which shows different stacking combinations for the 5300 series MCU and port capacity for each.

  Regarding the page layouts, the 5300 series follow the same layouts class microcontrollers such as the 4000 series and MSE 8510.  In the MCU 5300 Administrator's guide, it covers some of these layouts.

  The packing is just another word as reunification when compared with other microcontrollers, it allows you to join two or more microcontrollers (two can only be stacked/grouped in the 5300 MCU series).  Once on the other two microcontrollers are treated as a big MCU.

  Cascade, creates a link involved between two microcontrollers.  A MCU dials to the other as a participant and is treated as such in order to allow a larger participants to attend a conference of MCU another if one is at capacity.

  Hope this helps some.

• Two mcu 4205 cluster?

  Two mcu 4205 (4.4) with the same software both have 12 media port, now I have to make them work together as an mcu and 12 multimedia ports, have also the active guard and can be composed of devices or conferences by identification number, also I need if one of them is toward the bottom of the can function as main mcu and conferences continue

  How can I get there?

  Grouping/stacking of the MCU is not supported for 4200 series or 4500 to two MCU operate together as one.

  Clustering/stacking is supported only for the 5300 MCU series. You can only cluster/stack two units of the MCU.

  The idea of clustering/stacking the MCU is to increase capacity. The cluster will provide the sum of the capacities of the individual units. For example, if group you two microcontrollers that each supports 10 ports x 1080 p you supported a cluster which takes 20 ports x 1080 p.

  Optionally you can mount your two cascading 4205 microcontrollers:

  http://www.Cisco.com/c/en/us/support/docs/conferencing/Telepresence-MCU-4505/118763-config-MCU-00.html

  Another solution is that you need a Cisco conductor who works with VCS/CUCM.

  Take a look at these links for more information about deploying Cisco conductor:

  http://www.Cisco.com/c/en/us/products/collateral/conferencing/Telepresence-conductor/data_sheet_c78-709046.html?CacheMode=refresh

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/conductor/config_guide/XC3-0_docs/Telepresence-conductor-Cisco-VCs-B2BUA-deployment-guide-XC3-0.PDF

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/conductor/config_guide/XC3-0_docs/Telepresence-conductor-unified-cm-deployment-guide-XC3-0.PDF

  Kind regards

  Acevirgil

• Cisco MCU 5320 and Polycom vsx

  Hello!

  I have the problem with these devices. Content does not work properly. MCU push content to the same protocol with video endpoint vsx h.261. If the quality of the content are very poor. Is - this intraoperative problem or a software problem?  any other point endpoint it works very well.

  Hello

  You have basic Mode activate on your Polycom endpoint?

  Try to do either disable or enable basic Mode in your devices of Polycom, just to see if you get different behavior. You can find the slot configuration system > admin settings > network > call preferably.

  In addition, the date of issue for MCU version 4.4 indicates some interoperability issues with Polycom HDX endpoints when using content with H261 Protocol, do not know if this limitation also applies to the VSX series.

  In addition, I suggest you check the documentation for Polycom to check if the VSX endpoints are able to share content using protocols H263 or H264 instead of H261, also check if there is some version or configuration required to enable it.

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• function key for secure (HTTPS) management in MCU 4501

  Hello

  Please key to activate the secure HTTPS for MCU 4501 management?

  Thank you

  You must order L-AESCDN-K9 =

  His zero dollars.

  http://www.Cisco.com/c/en/us/products/collateral/conferencing/telepresen...

  AES and HTTPS encryption for post sale MCU 4500 Series upgrade Option

  L AESCDN-K9 =

  Kind regards

  RACLOT

• HP designjet 4500 36 "scan: scan HP designjet 4500

  I wish this scanner with usb with win 10 connection to ise, or win 7 but ı can not find a driver for scanner. It was made contex co for the hp md67m model No.... Number of Q1277a of hp... (Pc scanner does not work so I bought the new pc to scan...) I then need driver)

  Thanks for your interest. I try to use the software context but ı couldnot find dg67m maintarance driver file... So when ı use usb com 'unknown device' soft contex pc "there is no scanner find" "then?
  
  I even look at scan time on contex... G600 series like 4500. I have ıse this scanner softvare. If you know any model on contex-same with dg67m please write... Thank you...

• HP Officejet 4500 g510-m, it scans, but it does not print

  Hello

  I have a HP Officejet 4500 g510-m, which seems to work fine. When I connect it to my laptop, which is a Sony VAIO with windows 7 64 bit, using a usb cable it scans normally but it does not print. There is no error push up, even in the print queue's list as his impression, just not as a document waiting or anything. I've uninstalled and reinstalled the drivers, but nothing happened.  I used printing HP and doctor Scan of your site and it print an internal test page, but not one sent from the computer, so he said that this is not a hardware problem, but something is wrong with the software. On other computers, it works fine. Could you help me?

  Thank you

  Lena

  Hi Lena,.

  Please try to use an alternative driver steps and let me know if this helps,

  It should then allow any functionality such as printing, scanning and fax.

  Open Control Panel, and then select devices and printers.

  Right-click on the icon HP Officejet 4500 (be sure not to select the icon of the series Fax 4500), and then select printer properties.

  If there is no such icon 4500, that it can be combined under any other icon, right-click on the computer icon and look then to the properties of the printer, if not do a right-click any listed printer and check if the icon of 4500 sub list the properties of the printer option.

  Click the Advanced tab, and then click new driver. Follow the dialog box until the sweepers list appears, select HP, and then select the HP Deskjet 6940 printer (it is alphabetic sorted by different printers series)... If there is no such clcik pilot the Windows Update icon and allow it some time to update, and then search the list once again appear.

  Follow the steps to complete the wizard and confirm a dialog window, then try to pritning with HP Deskjet 6940 replacement icon.

  You can see any difference?

  Shlomi