Capture of Lightroom CC attached does not recognize the Nikon D750 & D7100

Similar Questions

• I just bought 6 of Lightroom. It does not recognize the RX10II sony raw files.

  I just bought 6 of Lightroom. It does not recognize the RX10II sony raw files.  (RAW ARW file type).   I checked the web site of Adobe, it says version 6.1.1 LR. reads the ARW files.    6.1.1 seems to be only available in CC.  Is this correct?  My purchase was a waste of money?

  Advice please.

  Lightroom 6.1.1 isn't Lightroom CC. Lightroom 6.1.1 is a stand-alone version and not required Lightroom CC. This is a free update to the version you have now. Download the last 6.3 maintenance of Lightroom Lightroom

• Lightroom 6 PC does not recognize the serial number and has disabled the module development

  I bought Lightroom 6 at Amazon and initially installed without problem. Recently, he started saying that my trial is about to expire. I had uninstalled the trial before installing the original. Now it's saying my trial has expired and has disabled the develop module.

  I tried to get my serial number, but it has no effect and does not give error messages.

  I tried to uninstall. I tried to re - download the app on Amazon. Nothing works. I get just this screen:

  

  It is not necessary to uninstall the trial version before installing the "full" version, because there is no difference in the programs. It is virtually the same program. Enter a valid serial just cancel the limitations of the trial. Your installation seems to act as creative cloud installation. My recommendation would be for you to uninstall completely, including the creative application manager if it is still installed. Download the latest update from the following Web site, and then install it. Use this serial number to see if it will activate.

  Update of Lightroom

• Lightroom CC (2015) does not recognize the lenses since the last update

  I installed updates to Lightroom CC (2015), CC Bridge and Photoshop CC (2015) on 20 March. Since then, LR does not have lens ID in the exif data. It displays all the lenses as 'unknown '. This issue coincides with the last update and I confirmed that the lens information in the exif data. What is the reference for this?

  It will not be restored automatically. My understanding is that after upgrading to the next version, it will be necessary to filter the images concerned, select all, Ctrl / Cmd + S to write metadata (in order to keep all work performed since importation), then do file metadata reading to get the lenses update info.

• Adobe Lightroom 5.7 does not recognize the Canon 60 d raw files. I have the plugin installed Camera Raw 8.7. Is there a solution?

  CS6 Bridge or Lightroom 5.7 can recognize the Canon raw (Canon 60 d camera) file.

  It started a few months without change I made to the system

  Clues?

  I think I found the answer - EOS Utility was running in the background and the 60 d can 'talk' more than a software download. After you have uninstalled the EOS Utility, things seem to work.

  Thank you all for helping solve the problems.

• My version of Lightroom does not recognize the RAW Olympus Pen - F file

  My version of Lightroom, 6.3, does not recognize the RAW Olympus Pen - F file. When an update that contains my new camera? Thank you

  Yes, version 6.6 will support raw files.

  Of course, you can test and report.

• 6 Lightroom does not recognize my Nikon D700 in trying to use Tethered Shooting.   I have the right cable to attached tools I think. It happens with no camera detected.   Camera is on.

  6 LightRoom does not recognize my Nikon D700 DSLR.   I have connected the PC to my DSLR using Windows 10.   I entered the program 6 of Lightroom and selected "file/Tether Capture / captive Start Capture."  He then says "No Camera detected"

  I think I have the right cable attached. It is a 5 Pin mini-cable USB 2.

  The mini USB camera works, I think.  I uploaded photos from the D700 to my computer before.

  When I connect and disconnect the tie between my laptop and the D700, computer one problems

  sound of Bell saying he acknowledged a connection to the laptop device.

  What could be wrong?

  Thank you!

  Len.

  Hello

  Please upgrade to the latest version of Lightroom, and the question to tie with El Capitan will be resolved: keeping up-to-date for Lightroom

  Kind regards

  Tanuj

• Tips on how to get attached with Nikon D810 and Lightroom - I tried with the uSB cable but Lightroom does not recognize the camera. My memory card has no images on it that I read somewhere that it can slow things down if it has pictures on i

  I tried to use the uSB cable, but Lightroom does not recognize the camera. My memory card has no images on it that I read somewhere that it can slow things down if she has no images on it

  If you use Lightroom CC / 6 on a Mac OSX El Capitan you must update to the latest version of CC 2015.4 / 6.4. Problems with Nikon capture home has been fixed in the latest update, the lis below.

  Lightroom Journal | Tips and advice straight from the Lightroom team.

• I am trying to download an update of Lightroom, but it does not recognize my serial number.

  I am trying to download an update of Lightroom, but it does not recognize my serial number.

  Error "serial number is not valid for this product". Creative Suite

• 6 Lightroom does not recognize the raw files of Nikon D800

  I have a nikon D800 and Lightroom does not recognize the raw files yet of this camera.  I've updated the LR software to 6.1.1 yet still cannot import files.

  Can you help me

  Thank you

  Ruben

  The D800 has been supported since Lightroom 4.1.

  You use an earlier version of the Nikon software to transfer files from camera to computer? Older versions are known to make Raw files unreadable by Adobe software.

  Try to download a version update of Nikon. Or use a different card for example reader method.

• I bought a Nikon D7100. Lightroom does not recognize the Nef Raw files what I am doing wrong?

  I bought a Nikon D7100. Lightroom does not recognize the Nef Raw files what I am doing wrong?

  Thank you for your response. I solved the problem by simply importing the

  images using windows rather than the Nikon transfer.

  In a message dated 09/03/2015 20:00:49 Hawaiian Standard Time,

  [email protected] wrote:

  I bought a Nikon D7100. Lightroom does not recognize Nef Raw files

  what I am doing wrong?

  created by BKKDon (https://forums.adobe.com/people/BKKDon) in Photoshop

  Lightroom - see the discussion complete

  (https://forums.adobe.com/message/7270711#7270711)

• DreamColor LP2480zx does not recognize the USB for calibration

  Hello

  I have a DreamColor LP2480zx, which does not recognize the USB connection to the computer during calibration.  I have my eye HP connected through this monitor, so I know the connection and the cable is good and mouse, keyboard.  My setup is like this:

  Reference Dell 690 running 64 bit + Windows XP

  DreamColor LP2480zx

  Apple Cinema Display 23 "

  I bought the DreamColor used, and in all other respects, it seems to work very well.  The original owner didn't have it calibrated within a certain time, but said that having had no problem with the previous calibration.  I installed the last APS (version 2.0) and updated to the latest firmware.  These updates produces no change in recognition USB problem.

  The interesting thing is, I was able to calibrate the Apple Cinema Display, using the same configuration of connection (mouse, keyboard, and HP eye connected to the computer via the LP2480zx) APS was able to see the USB connection and this very well calibrated monitor.

  I had trouble with this problem for a few days.  I've looked around quite a bit online and found a few others who have this same problem, but I did not yet find someone who can point out a solution.  If anyone has had this same problem, or has heard of results that correct it, please let me know, because it's very frustrating.

  Thanks for any help

  Clay

  An update to my previous post, I realized a work around for this problem.

  Apparently, this problem has to do with the Dreamcolor screen and/or software APS do not like working with 64 bit systems.  I'm not saying that it is always the case, but I saw the other posts on this problem on 64-bit systems, and I spoke with two other people personally who told me that they also had the same problem, try to calibrate its Dreamcolor monitor when it was attached to a 64-bit system.  HP does not seem to be concerned about this problem, because they do not even recognize its existence, but since I'm far from being the first to report this problem, he's obviously not a one-time problem.

  My solution was this: I had connect the monitor to a regular running XP 32 bit system.  After I did, I could re - calibrate the monitor without the problem of USB connection.  This isn't a very good solution because not everyone has access to several machines, running different operating systems.  But it's a work around, and it worked for me.

  Hope this helps other people who have this same problem with their Dreamcolor monitors hooked to their 64-bit systems.

  Clay

  PS- I posted this as resolved, only because I was able to calibrate my monitor.  It's not really solved the problem, but it gets the monitor working again.  Maybe HP will address this problem in the future, but I'm not holding my breath.

• Canon 60 d does not recognize the 430ex II flash. Any suggestions?

  Canon 60 d does not recognize the 430ex II flash. On the menu screen, it says that flash is where not compatible.

  Any suggestions? Books or guides recommended?

  Thank you

  A few...

  I hope that you have verified that the flash lights up completely and you get the red light showing that it is ready to fire.

  On your system menu 60 d, if you find the "Flash control" option, you can ensure that you have not set the external speedlite to 'disable' - although I think in this mode, you wouldn't get the message you describe.  that is, I doubt it's, but you can double check.

  A more common reason for the failure is that the flash of the camera can perfectly communicate with flash.  This is usually due to a bad connection in the 'foot' of the lightning.

  The flash must be in place in the rails of the claw.  Make sure that the lock is released, fully slide the flash into the rails of the hoof, stop.  Engage the locking of the foot, so we got him firmly (it will slide to the right and then click sur-pour-snap (you must press the button to release the locking lever).)  This is not * only * snug foot... He also puts a tiny metal pin locking in a small hole in the claw so that flash can't get out.

  At this point, the "foot" of the flash is actually the "ground" connection and he is in contact with the metal rails of the claw AND the five contacts on the foot must be in contact with the camera.

  This means there is nothing wrong with the flash - and there could be something wrong with her.   So if you are convinced you fully secures the flash, then remove the flash and inspect the "foot" on the flash.

  The metal plate on the bottom of the flash must be strong... If you use your fingers and try to move it (do not use a heavy force... we do not break - just firmly grasp and see if he's going to move at all) it should not move.  If it does not move that this means that the foot is loose and is not attached to the body of the flash (there are four very small screws which hold it firmly, but they are accessible from the inside of the flash.

  Next, inspect the 5 metal pins on the bottom of the flash.  Each of these areas is spring loaded so that they will stand against the 5 points of contact in the camera shoe.  I sometimes saw a performance of something (for example, a bit of sand) getting stuck and 'jam' a PIN so that she she brings more contact with the contact on the hoof.  If you view the foot of the flash of an edge - on view, all the pins it is back to the same height.  If one of them is lower than the rest... indented it is blocked.

  The 430EX II has a solid reputation as a flash work horse.  It tends to be among the most reliable flashing on failures is rare.

  It is also possible that the problem is in the camera.  A simple test of this is to try an another speedlite (if you have one, or if you have a friend who has a).  If it's your speedlite, and it is under warranty, then it is probably a simple remedy of service Canon.

  If the flash is not under warranty and that the problem is with the hot-shoe is is not solid, it is often an easy repair.  If a foot have been irreparably damaged, the entire foot can be replaced (everything is a module) and it is an easy and I think a little low cost repair.

• New installation of XP PRO sp3 does not recognize the 500 GB HD

  OK, here are the details:

  System: Computer PORTABLE of Acer Aspire 1700 Pent4, 2 GB of RAM, 80GB (3.5 "full-size, trainee) IDE HD [this is the original HD on this laptop of size important which is designed to use disks 3.5" hard].

  Initial situation: Windows XP Pro (SP3 integrated) installed on HDD of 80 GB and works without poblems. BIOS does NOT show the ability of the intern HD in the BIOS screen. BIOS reports only the model and the serial number of the HD, and there is no options to specify the HD type/format (e.g., MLA, etc.)

  Available: Win XP Pro bootable CD slipstreamed with SP3; It is tested and verified work well to install PC or laptop!

  When running XP Pro on a partition internal 80 GB HD, and when I join a brand new WD 500 GB IDE HD via USB, HD is recognized correctly. I can partition and copy data on the HD 500 GB with no problems!

  When I replaced the old 80 GB HD with the new HD 500 GB HD interning on the laptop, I have the following problems:

  1. I can NOT boot into Windows XP Pro (SP3) which was Ghost on the HD 500 GB of the old 80 GB portable HD it recharges, and if I try the console recovery or secure boot, then the laptop restarts also.
  1B. I have Ghost xp partition to 80 GB HD to a piece of spare HD (40 GB) and replaced the 80 GB with the 40 GB HD and was able to start the laptop without problem. So the problem is NOT related ghost!

  2. I can't perform a clean install of Windows XP Pro (SP3 integrated) because Windows XP Setup recognizes the HD 500 GB GB 131 HD. Therefore, the remaining capacity is not recognized.

  3. I can NOT perform the installation of Windows XP pro (SP3 integrated), even if I have previously partition new HD 500 GB by attaching it to a free desktop PC and use Partition Magic, partitioner of Paragon Disk or other partitioning tools. After partitioning prior, when the 500 GB HD is installed on the laptop (as a trainee HD), then win xp installation lists quality HD of GB 131 and lists the existing partitions as corrupt!

  4. Curiously, if I use Knoppix, Debian, Ubuntu or linux boot CD Mint and start the laptop computer with one of these linux distributions, then the linux installer recognize the HD properly during the phase of recognition of material and later during the phase partitioning HD, the linux system to report a full capacity of 500 GB available for partitioning. In addition, when there are partitions, partitioning linux program then lists these partitions properly as well!

  Considering the 4 points and especially MS Windows XP PRO (integrated with SP3, which should recognize HD with sizes exceeding 137 GB limit - from MS says you must be at least XP SP1 to overcome the size 137 GB limit - and that the different distributions of linux can see the full-size HD 500 GB with no problems) which is exactly the problem with Win XP? Why it does not recognize the full capacity? And how to win xp recognizes a 500 GB capacity, if the new HD is attached to the laptop via USB as an external drive when running XP PRO (SP3) of the 80 GB internal HD?

  so... Can anyone sheds light on the issue with Win XP Pro installation on HD 500 GB IDE?

  Nicely,

  LO

  Hi Palcouk and Doc,

  I think that's the final answer!

  Although, there is a mixture of simple to complex responses to the problem at hand, what it all comes down is that there is a significant difference between the installation of Windows XP and Linux installer program. The XP installation program needs help from the BIOS to deal with HD, and if the BIOS does not support, XP not has no facility to remedy the situation. OTOH, most of Linux new kernels rely on the BIOS for a limited number of extended, but communicate directly with the hardware, in this case, with the HD and therefore manages the material accordingly.

  It seems among users of dual-booting (win/linux) using old PCs, it is a matter of very pretty. What they end up doing is using the first 137 GB that is seen by the BIOS without problem for XP (either as a single partition or divided into several partitions), and the rest of the space is used for Linux because linux has no problem.

  I guess that it really nails the problem with my laptop to a BIOS NON-lba-48-bit!

  Then close this thread as answered or matter who has more to say about this?

  LO

  P.S.: It was very nice meeting you fellows and appreciate all the help and tech expertise.

• iMac does not recognize the function analysis of the LaserJet Pro

  My iMac has OS X v. 10.7.3.  It does not recognize the analysis function of the HP LaserJet professional M1217 MFP nfw which is connected wireless.  I can print with the HP success but the dialog box not incllude not a scan option.  I can't scan from preview or iPhoto or (as suggested by some rsources).  I tried to connect the printer LaserJet by USB but that doesn't solve a problem either.  I uninstalled and reinstalled the software, including HP PrinterDrivers.pkg.  I get the automatic updates from Apple which have not helped.

  Hello

  I apologize for any inconvinence,

  The Director of HP taken do supported by Lion for some specific models, including the M1217.

  However, as mentioned above, only the latest version of the software supported by Lion. any prior version of the software is not supported by the operating system.

  If you have not installed the complete softwatre features attached to my previous post, please be sure to install it. It is compatible with Lion you will find listed on the download page.

  Compatibility: Mac OS X 10.4, Mac OS X 10.5, Mac OS X 10.6, Mac OS X, Mac OS X 10.7 
  

  I appriciate if you can guide me where you see the information that the HP Director is not supported by the OS, I can't take any possible measure to get it corrected.

  Thank you and best regards,

  Shlomi