card network - need to restart problems

Similar Questions

• Error "the network card experiences driver or hardware problems" and "To ensure that your Internet protocol bindings are Correct" on Dell Inspiron 530

  Original title: 'make sure that your Internet protocol bindings are Correct (DELL Inspiron 530 Intel 82562V and Desltop)
  
  I'm doing tech support for the family and I'm stumped. They had a Dell 530 with an Intel 82562V-2 and is no longer connected to the internet.

  ipconfig/all statements

  Hostname...: wayne-PC
  Suffix main DNS...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  That's all. Windows gives errors two errors:

  (1) the card network knows of driver or hardware problems

  (2) check that your Internet Protocol connections are Correct

  I installed the latest Intel drivers and TCP IP settings are checked for V4 and V6. I even went as far to install a new Dynex Ethernet card that gets the same mistakes.

  I even tried the netsh reset ip and netsh winsock reset command. I have no idea what to do next. I searched glasses and found similar problems with the same model of Dell and card, but they have been fixed by rebooting.

  Hi MButIer,

  -How long have you had this problem?
  -Was any change in software because the computer before the show?

  Follow the steps mentioned below:

  Step 1:

  Temporarily disable the antivirus software (and any other security software) and the firewall on the computer as a test. Once disabled check if you can connect to the internet without any error.

  If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program. Please contact the software vendor for assistance in this regard.

  Note: Make sure that you enable the antivirus software, other security and firewall programs.

  Warning

  Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Step 2:

   

  Perform a System Restore to a point before the show and check if this solves the problem.

  See also:

  System Restore: frequently asked questions

  If the steps above do not help, the best would be to get in touch with the Internet Service Provider (ISP) for assistance.

  Hope this information helps.

  Gokul - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• WANT to PC dv7: at startup, I get a blue screen with a :( Your PC has encountered a problem and needs to restart.

  While I was using my laptop I received a message that HP was running some sort of program disagnostic and in the end, he asked if I wanted to repair the problems. I declined the offer. However, the next time I turned on the computer, I saw the first time the HP logo, then the message "automatic repair Preparation". After a few seconds there is a short rectangle that flashes on and disappears. Then I got a blue screen with: your PC encountered a problem and needs to restart. We will restart for you. "Who starts a blue screen and reboot cycle. Blue screens replacement error messages saying: "If you want to learn more, you can search online for later for this error" and once it will say 'FAT file system' and once 'NTFS file system. I have spent to support HP dv7 ENVY page and tried the suggestions of repair without success. Is it possible to go beyond these two error messages and their blue screens to get my system working again? If so, how?

  Hello

  Error code 24 characters is a failure of the short test (DST) disk Self and would indicate that hard is defective and must be replaced.  It is also consistent with your description of the problem.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - if necessary, you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are no longer under warranty, it's a fairly simple procedure to replace the HARD drive yourself - a brief guide on this is below.

  Readers on the following links are examples that would be perfect for your laptop.

  Hard drive 500 GB

  750 GB hard drive.

  1 TB laptop hard drive.

  The procedure to replace the hard drive begins on Page 56 of your maintenance & Service Guide.

  About reinstalling Windows 10 on new HARD drive, as long as the previous installation of Windows 10 had activated Ok after upgrading to Windows 7/8.1, you can simply create your own Windows 10 installation media and perform a new installation as described in the guide on the following link.  Note: On the activation screen, select "I have not a product key" - Windows will activate automatically once installation is complete.

  http://www.howtogeek.com/224342/how-to-clean-install-Windows-10/

  Kind regards

  DP - K

• Satellite C660 - 1 M 0 encountered a problem and needs to restart

  Hello
  Today, when I turned on my laptop before it starts, I get a blue screen says:
  Your computer has encountered a problem and needs to restart. Collection of information.

  What is this problem for?
  My laptop is TOSHIBA Satellite C660 - 1 M 0 i3

  Is this a Windows problem?

  Here is a message I received in Windows7forums on this subject but I don't understand what he means, can understand you for me please? e

  * Re: Heeelp! Your computer ran into a problem! *

  These screens generally include a sentence in the screen "fallen on problems." Usually something like Violation of Watchdog DPC (Deferred procedural call) and are often associated with a bad driver and or a power saving state not supported (sleep, hybrid sleep, hibernate, etc.,)

  First of all, make sure that you have the latest drivers from your computer manufacturer and or the individual device manufacturer's Web site. Then consider whether this computer manufacturer includes any software that may be incompatible with Windows 8 CP or is somehow patented conflict with Windows 8 CP in energy saving power scheme options. You may need to experiment a little, maybe remove the proprietary tools or taste affecting your schema of high performance or even the options down or max.

  The overview of consumption is more or less a new frontier for everyone here to work through this kind of problem is going to be informative and beneficial for all who read your thread, so please keep us posted as to how you are progressing with your current number.

  Concerning
  Randy

  Hello

  Blue screen of death (BSOD) may be caused by software or hardware problems.
  To know if it of really a software problem, you can try running a HARD drive recovery procedure which would fix the laptop back to factory settings.

  What is an option for you?
  If Yes, check this:
  + How to recover a Toshiba notebook with the HDD recovery procedure.
  http://APS2.toshiba-tro.de/KB0/HTD1303440001R01.htm

• R253cl 15 HP: pc encountered a problem and needs to restart. NO LESS driver IRQL OR EQUAL (rtwlane.sys)

  NO LESS driver IRQL OR EQUAL (rtwlane.sys)

  Hi @bazrul,

  Thank you for your inquiry.

  I understand that when you try to start your laptop, you get the error ': PC encountered a problem and needs to restart. " NOT LESS DRIVER IRQL OR EQUAL (rtwlane.sys)".

  I'm assuming you get a blue screen with this error and are unable to load Windows. Is this correct?

  You can start in safe mode?  HP computers - Windows Safe Mode (Windows, 10, 8).

  If you are able to boot into safe mode and that you have installed Norton, you can try to uninstall it as others have said that solved the problem.

  If this is the case and you can again access Windows, run the HP Support Assistant to acquire the recommended updates.

  I also suggest to do the Windows updates.

  Please let me know the results.

  Good luck!

• Photo folder "Windows explorer has encountered a problem and needs to restart" and I cannot access any of my photos.

  Windows Vista and, recently, I scanned a few photos and now my pictures folder won't open and gives me an error "Windows explorer has encountered a problem and needs to restart" and I can't access any of my photos.

  Hi LuiMTX,
  

  This problem is only limited to the pictures folder?

  Method 1: Let flow the fixit available in the link below and then check

  Windows Photo and slideshow problems
  http://support.Microsoft.com/GP/windows_photo_and_slideshow_diag/en-us?EntryPoint=lightbox

  Method 2: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the File System Check
  ER tool to troubleshoot system missing or corrupt files on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

• The blue screen of death error your PC encountered a problem and needs to restart. and we will launch it for you

  I use a desktop computer, Dell XPS 8300, the blue screen looks like this

  " :( Your PC has encountered a problem and needs to restart. "and we will restart it for you.
  Then a blue screen that says:
  «Your pc is not properly start the automatic repair press on restart to reboot your PC, which can sometimes solve the problem.» Alternatively, you can press Advanced Options»
  NONE OF THESE WORK
  I can get the boot menu by pressing F12 at startup, NONE OF THESE OPTIONS WORK

  Help, my computer has been down for a week.

  Hello

  Thanks for posting your query to the Microsoft Community. Sorry for the delay in responding.
  Please go through the steps in this article and check if it helps.

  Resolve stop (blue screen) error in Windows 7

  Hope that the information provided has been helpful and let us know if you need more help. We will be happy to help you.

• Windows 8 stuck in reboot loop ' your pc encountered a problem and needs to restart. We collect only some error information, and then let's restart for you"

  My laptop was working fine last night, but I left it on and unplugged and he died. This morning, I'm an endless loop of ' your pc encountered a problem and needs to restart. We collect only some error information, and then let's restart for you"

  the message appears for a second and then the VAIO logo reappears before the pop blue screen for a second. This goes just forever with no additional info. I can see an additional line appear on the blue screen every time everything as it turns off so it is unreadable.
  Help please?
  more information: the percentage never bar going past 0% it pop right to the top and back immediately to the VAIO screen.

  Hi Wesley,

  This problem could be due to corruption of the system files, I suggest you try to perform auto repair using Windows 8 disc of Windows recovery environment (WinRE) and check if it helps.

  To run auto repair on follow computer Windows 8 as follows:

  a. Insert the media (USB or DVD) and restart your computer.

  b. press on the key F12 (usually it's F12, but it may differ between computer manufacturers) and choose the drive in which you inserted into the installation media.

  c. once the Windows Setup window appears, follow these steps:

  d. click Next and select repair your computer.

  e. you will see an option to choose and then a blue screen. Choose the troubleshooting option and select advanced options.

  f. you can choose automatic repair of the advanced boot option.

   

  Keep us updated on the status of the issue.

• Window 8 - your PC has faced a problem needs to restart

  I had a light blue screen everytimes that says 'Your PC came across a problem and the need to restart'. Is there anyway I can find out what the problem on? It's boring. Help, please.

  Here is a link of my Minidump files:
  https://SkyDrive.live.com/redir?RESID=37DC912F2C1DB026! 110

  Thank you!

  The minidump files point to the mfewfpk.sys which is a Mcafee driver:

  BugCheck D1, {158, 2, 1, fffff8800200b7b3}

  WARNING: Unable to verify timestamp for mfewfpk.sys
  ERROR: Module load completed but symbols can be loaded for mfewfpk.sys
  Probably caused by: fwpkclnt.sys (c:\windows\system32\drivers\fwpkclnt! FwppInjectionStackCallout + c8)

  These accidents can have two programs of third-party antivirus/firewall real time installed, McAfee and Avast.

  I would say to uninstall McAfee and Avast and see if the errors to solve.

  Subsequently, you can reinstall McAfee or Avast, using the most recent version, or go with alternative security such as firewall and antivirus integrated Windows 8 (Windows Defender) software.

• Windows 8 Light Blue error screen: your PC Ran into a problem and need to restart

  Every once a while I reboot my windows, I had a light blue screen that says "your PC came across a problem and the need to restart.
  Is there anyway I can know what is the problem, I don't want to reinstall windows again, please help
  Here is a link of my Minidump files:

  https://SkyDrive.live.com/redir?RESID=38EC4E1D886E0DA8! 105

  Thank you!

  The minidump files showed a BAD_POOL_HEADER stop error (19) caused by the MacHALDriver.sys:

  BUCKET_ID: 0x19_20_MacHALDriver+ 1714

  Bootcamp.exe is the process that blocks.

  Try the following link to get suggestions for this problem:

  https://discussions.Apple.com/thread/4466080?start=0&TSTART=0

• Why do I get a blue screen that says your PC is encountered a problem and needs to restart. We are only collecting the error information and then it will reboot for you.

  Why do I get a blue screen that says your PC is encountered a problem and needs to restart. We are only collecting the error information and then it will reboot for you.

  https://www.dropbox.com/s/2dtm74f6ki7goa4/minidump.zip

  DAG

  These were related to your driver atheros wifi athw8x.sys I would like to re - install the latest driver available.

  If you continue to plant I remove Symantec and use the built in Defender

• "Receive the error message" your PC has encountered a problem and needs to restart.

  Original title: stuck in a reboot loop, can't connect.

  Today, my laptop (VAIO, Windows 8) restarted while I was there and since then has been very slow to start. During loading, I get messages such as 'Your PC came across a problem and must restart' and then 'preparation auto repair' again and again.

  I have tried rebooting several times and sometimes I'll get to the login screen, but when I log into my account (which is the only one available) it says "could not load user profile. Right now, I restarted and did not get to the login screen. It says "repair disk errors. This can take more than an hour to finish."

  Windows 8 is the operating system that is installed with the system. I tried to boot into safe mode several times (SHIFT and F8 at startup), but instead to get a menu of options the computer says "Your PC encountered a problem and needs to restart" and starts all over again.

  Hi Geo,

  What is the model number of the Sony VAIO laptop?

  This problem could be due to corruption of the system files, I suggest you try to perform auto repair using Windows 8 disc of Windows recovery environment (WinRE) and check if it helps.

  To run auto repair on follow computer Windows 8 as follows:

  a. insert the media (USB or DVD) and restart your computer.

  b. press the key F12 (usually it's F12, but it may differ between computer manufacturers) and choose the drive in which you inserted into the installation media.

  c. once that the Windows Setup window appears, follow these steps:

  d. click Next , and then select fix your computer.

  e. you will then see a blue screen and an option to choose. Choose the Troubleshooting option and select Advanced options.

  f. you can choose automatic repair of the advanced boot option.

  Keep us updated on the status of the issue.

• Your computer has encountered a problem and needs to restart - HAL_INITIALIZATION_FAILED

  I have Windows Workstation 10 and now I find I can't create virtual machines with Windows server 2012.  At the point where the VM load iso attached, I get the error - YOUR COMPUTER RAN INTO A PROBLEM AND a NEED OF RESTART - HAL_INITIALIZATION_FAILED - IN ITS COLLECTION ERROR INFORMATION AND will START: 0 SECONDS.

  I tried to download the latest version of Workstation 10.0.3 but I still have this problem.

  Anyone got any ideas?

  Bryan

  Post edited by: a.p. - canhed title in capital letters.

  What type/model of CPU do you have in your host? Make sure that in the case of an Intel - "Virtualization technology (VT - X)" as "Execute Disable Bit (XD)" - are "enabled." In the case of an AMD processor, it's 'No Execute (NX)' which must be enabled. Make sure that you turn on the host after changing any of these settings in the BIOS, a simple reboot may not be enough.

  If this does not resolve the problem, please join the virtual machine vmware.log file to a response message.

  André

• Windows Update cannot currently check the update, because the service does not work, you may need to restart your computer

  My computer stops the update via WIndows Update Component

  Whenever a try to do the manual update using this component I get the message;   * Windows Update cannot currently check the update, because the service does not work, you may need to restart your computer *...

  My computer has a few updates, but can not run these update

  Whenever I try to run computer shotdown/updates remain frozen for a while and stops without updating

  He starts to run updates 1 of 13... and stops

  If I shutdown normal e, computer stay likehanging 1 hour without stopping.

  I would like to know how to solve this problem

  Thank you

  Concerning

  Gladmar.

  Hello

  Were there any changes made on the computer before the show?

  Perform the following methods and check:

  Method 1:

  I suggest you to check if you are able to access Windows Update service and ensure that the following services are started. If it is not started, follow these steps:

  a. click Start, type services.msc and press enter.
  b. search Windows Update.
  c. right-click on the service and select Properties.
  d. in type of startup, select enable.
  e. click Start under the Service status.
  f. click OK.
  g. Repeat steps c to f for the following services:

  Background Intelligent Transfer Service
  Cryptographic services

  If the steps do not help to solve the problem, you can go ahead with the methods mentioned below and check.

  Method 2:

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Method 3:

  Your anti-virus software is in conflict with Windows updates. You can test this by temporarily disabling your antivirus:

  Disable the antivirus software
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 4:

  The problem with Microsoft Windows Update is not working

  http://support.Microsoft.com/mats/windows_update/

  See also:

  Troubleshoot problems with installing updates
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  Updates: frequently asked questions

  
  http://Windows.Microsoft.com/en-us/Windows-Vista/updates-frequently-asked-questions

  I hope this helps.

• Error message "WIndows cannot currently check the updates, because the service is not running, you may need to restart your computer.

  Error message "WIndows cannot currently check the updates, because the service is not running, you may need to restart your computer.

  I am currently using windows 32 bit vist

  I rebooted, I changed the settings, I don't have a file called window update service in the service section to stop and start, I tried the fix programs, I'm out of ideas and I need help!

  Suggestions?

  Hello

  1. have you made changes on the computer before this problem?

  2. which antivirus app do you use?

  I suggest you try these methods and check.

  Method 1:

  Anti-virus software may conflict with Windows Update. You can temporary disable them and check the issue.

  Disable the antivirus software
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2:
  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058
  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article:
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 3: If the methods above do not help, I suggest you delete the edb.log file and check if that helps.

  Follow these steps:

  a. click the Start button, click computer.

  b. now, go to this site: C:\windows\softwaredistribution\datastore\logs\edb.log
  Where 'C' is the drive of operating system
  c. delete the log file, and then restart the computer and check the issue.